1 /* 2 * Configuation settings for the Freescale MCF5485 FireEngine board. 3 * 4 * Copyright (C) 2004-2008 Freescale Semiconductor, Inc. 5 * TsiChung Liew (Tsi-Chung.Liew@freescale.com) 6 * 7 * SPDX-License-Identifier: GPL-2.0+ 8 */ 9 10 /* 11 * board/config.h - configuration options, board specific 12 */ 13 14 #ifndef _M5485EVB_H 15 #define _M5485EVB_H 16 17 /* 18 * High Level Configuration Options 19 * (easy to change) 20 */ 21 #define CONFIG_MCF547x_8x /* define processor family */ 22 #define CONFIG_M548x /* define processor type */ 23 #define CONFIG_M5485 /* define processor type */ 24 25 #define CONFIG_DISPLAY_BOARDINFO 26 27 #define CONFIG_MCFUART 28 #define CONFIG_SYS_UART_PORT (0) 29 #define CONFIG_BAUDRATE 115200 30 31 #undef CONFIG_HW_WATCHDOG 32 #define CONFIG_WATCHDOG_TIMEOUT 5000 /* timeout in milliseconds, max timeout is 6.71sec */ 33 34 /* Command line configuration */ 35 #include <config_cmd_default.h> 36 37 #define CONFIG_CMD_CACHE 38 #undef CONFIG_CMD_DATE 39 #define CONFIG_CMD_ELF 40 #define CONFIG_CMD_FLASH 41 #define CONFIG_CMD_I2C 42 #define CONFIG_CMD_MEMORY 43 #define CONFIG_CMD_MISC 44 #define CONFIG_CMD_MII 45 #define CONFIG_CMD_NET 46 #define CONFIG_CMD_PCI 47 #define CONFIG_CMD_PING 48 #define CONFIG_CMD_REGINFO 49 #define CONFIG_CMD_USB 50 51 #define CONFIG_SLTTMR 52 53 #define CONFIG_FSLDMAFEC 54 #ifdef CONFIG_FSLDMAFEC 55 # define CONFIG_MII 1 56 # define CONFIG_MII_INIT 1 57 # define CONFIG_HAS_ETH1 58 59 # define CONFIG_SYS_DMA_USE_INTSRAM 1 60 # define CONFIG_SYS_DISCOVER_PHY 61 # define CONFIG_SYS_RX_ETH_BUFFER 32 62 # define CONFIG_SYS_TX_ETH_BUFFER 48 63 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 64 65 # define CONFIG_SYS_FEC0_PINMUX 0 66 # define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE 67 # define CONFIG_SYS_FEC1_PINMUX 0 68 # define CONFIG_SYS_FEC1_MIIBASE CONFIG_SYS_FEC0_IOBASE 69 70 # define MCFFEC_TOUT_LOOP 50000 71 /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */ 72 # ifndef CONFIG_SYS_DISCOVER_PHY 73 # define FECDUPLEX FULL 74 # define FECSPEED _100BASET 75 # else 76 # ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN 77 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 78 # endif 79 # endif /* CONFIG_SYS_DISCOVER_PHY */ 80 81 # define CONFIG_ETHADDR 00:e0:0c:bc:e5:60 82 # define CONFIG_ETH1ADDR 00:e0:0c:bc:e5:61 83 # define CONFIG_IPADDR 192.162.1.2 84 # define CONFIG_NETMASK 255.255.255.0 85 # define CONFIG_SERVERIP 192.162.1.1 86 # define CONFIG_GATEWAYIP 192.162.1.1 87 # define CONFIG_OVERWRITE_ETHADDR_ONCE 88 89 #endif 90 91 #ifdef CONFIG_CMD_USB 92 # define CONFIG_USB_STORAGE 93 # define CONFIG_DOS_PARTITION 94 # define CONFIG_USB_OHCI_NEW 95 # ifndef CONFIG_CMD_PCI 96 # define CONFIG_CMD_PCI 97 # endif 98 /*# define CONFIG_PCI_OHCI*/ 99 # define CONFIG_SYS_USB_OHCI_REGS_BASE 0x80041000 100 # define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 101 # define CONFIG_SYS_USB_OHCI_SLOT_NAME "isp1561" 102 # define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 103 #endif 104 105 /* I2C */ 106 #define CONFIG_SYS_I2C 107 #define CONFIG_SYS_I2C_FSL 108 #define CONFIG_SYS_FSL_I2C_SPEED 80000 109 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 110 #define CONFIG_SYS_FSL_I2C_OFFSET 0x00008F00 111 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR 112 113 /* PCI */ 114 #ifdef CONFIG_CMD_PCI 115 #define CONFIG_PCI 1 116 #define CONFIG_PCI_PNP 1 117 #define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1 118 119 #define CONFIG_SYS_PCI_MEM_BUS 0x80000000 120 #define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BUS 121 #define CONFIG_SYS_PCI_MEM_SIZE 0x10000000 122 123 #define CONFIG_SYS_PCI_IO_BUS 0x71000000 124 #define CONFIG_SYS_PCI_IO_PHYS CONFIG_SYS_PCI_IO_BUS 125 #define CONFIG_SYS_PCI_IO_SIZE 0x01000000 126 127 #define CONFIG_SYS_PCI_CFG_BUS 0x70000000 128 #define CONFIG_SYS_PCI_CFG_PHYS CONFIG_SYS_PCI_CFG_BUS 129 #define CONFIG_SYS_PCI_CFG_SIZE 0x01000000 130 #endif 131 132 #define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */ 133 #define CONFIG_UDP_CHECKSUM 134 135 #define CONFIG_HOSTNAME M548xEVB 136 #define CONFIG_EXTRA_ENV_SETTINGS \ 137 "netdev=eth0\0" \ 138 "loadaddr=10000\0" \ 139 "u-boot=u-boot.bin\0" \ 140 "load=tftp ${loadaddr) ${u-boot}\0" \ 141 "upd=run load; run prog\0" \ 142 "prog=prot off bank 1;" \ 143 "era ff800000 ff83ffff;" \ 144 "cp.b ${loadaddr} ff800000 ${filesize};"\ 145 "save\0" \ 146 "" 147 148 #define CONFIG_PRAM 512 /* 512 KB */ 149 #define CONFIG_SYS_PROMPT "-> " 150 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 151 152 #ifdef CONFIG_CMD_KGDB 153 # define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 154 #else 155 # define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 156 #endif 157 158 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 159 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 160 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 161 #define CONFIG_SYS_LOAD_ADDR 0x00010000 162 163 #define CONFIG_SYS_CLK CONFIG_SYS_BUSCLK 164 #define CONFIG_SYS_CPU_CLK CONFIG_SYS_CLK * 2 165 166 #define CONFIG_SYS_MBAR 0xF0000000 167 #define CONFIG_SYS_INTSRAM (CONFIG_SYS_MBAR + 0x10000) 168 #define CONFIG_SYS_INTSRAMSZ 0x8000 169 170 /*#define CONFIG_SYS_LATCH_ADDR (CONFIG_SYS_CS1_BASE + 0x80000)*/ 171 172 /* 173 * Low Level Configuration Settings 174 * (address mappings, register initial values, etc.) 175 * You should know what you are doing if you make changes here. 176 */ 177 /*----------------------------------------------------------------------- 178 * Definitions for initial stack pointer and data area (in DPRAM) 179 */ 180 #define CONFIG_SYS_INIT_RAM_ADDR 0xF2000000 181 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in internal SRAM */ 182 #define CONFIG_SYS_INIT_RAM_CTRL 0x21 183 #define CONFIG_SYS_INIT_RAM1_ADDR (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_RAM_SIZE) 184 #define CONFIG_SYS_INIT_RAM1_END 0x1000 /* End of used area in internal SRAM */ 185 #define CONFIG_SYS_INIT_RAM1_CTRL 0x21 186 #define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - 0x10) 187 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 188 189 /*----------------------------------------------------------------------- 190 * Start addresses for the final memory configuration 191 * (Set up by the startup code) 192 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 193 */ 194 #define CONFIG_SYS_SDRAM_BASE 0x00000000 195 #define CONFIG_SYS_SDRAM_CFG1 0x73711630 196 #define CONFIG_SYS_SDRAM_CFG2 0x46770000 197 #define CONFIG_SYS_SDRAM_CTRL 0xE10B0000 198 #define CONFIG_SYS_SDRAM_EMOD 0x40010000 199 #define CONFIG_SYS_SDRAM_MODE 0x018D0000 200 #define CONFIG_SYS_SDRAM_DRVSTRENGTH 0x000002AA 201 #ifdef CONFIG_SYS_DRAMSZ1 202 # define CONFIG_SYS_SDRAM_SIZE (CONFIG_SYS_DRAMSZ + CONFIG_SYS_DRAMSZ1) 203 #else 204 # define CONFIG_SYS_SDRAM_SIZE CONFIG_SYS_DRAMSZ 205 #endif 206 207 #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE + 0x400 208 #define CONFIG_SYS_MEMTEST_END ((CONFIG_SYS_SDRAM_SIZE - 3) << 20) 209 210 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) 211 #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ 212 213 #define CONFIG_SYS_BOOTPARAMS_LEN 64*1024 214 215 /* Reserve 256 kB for malloc() */ 216 #define CONFIG_SYS_MALLOC_LEN (256 << 10) 217 /* 218 * For booting Linux, the board info and command line data 219 * have to be in the first 8 MB of memory, since this is 220 * the maximum mapped by the Linux kernel during initialization ?? 221 */ 222 #define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20)) 223 224 /*----------------------------------------------------------------------- 225 * FLASH organization 226 */ 227 #define CONFIG_SYS_FLASH_CFI 228 #ifdef CONFIG_SYS_FLASH_CFI 229 # define CONFIG_SYS_FLASH_BASE (CONFIG_SYS_CS0_BASE) 230 # define CONFIG_FLASH_CFI_DRIVER 1 231 # define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT 232 # define CONFIG_SYS_MAX_FLASH_SECT 137 /* max number of sectors on one chip */ 233 # define CONFIG_SYS_FLASH_PROTECTION /* "Real" (hardware) sectors protection */ 234 # define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 235 #ifdef CONFIG_SYS_NOR1SZ 236 # define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ 237 # define CONFIG_SYS_FLASH_SIZE ((CONFIG_SYS_NOR1SZ + CONFIG_SYS_BOOTSZ) << 20) 238 # define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_CS0_BASE, CONFIG_SYS_CS1_BASE } 239 #else 240 # define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ 241 # define CONFIG_SYS_FLASH_SIZE (CONFIG_SYS_BOOTSZ << 20) 242 #endif 243 #endif 244 245 /* Configuration for environment 246 * Environment is not embedded in u-boot. First time runing may have env 247 * crc error warning if there is no correct environment on the flash. 248 */ 249 #define CONFIG_ENV_OFFSET 0x40000 250 #define CONFIG_ENV_SECT_SIZE 0x10000 251 #define CONFIG_ENV_IS_IN_FLASH 1 252 253 /*----------------------------------------------------------------------- 254 * Cache Configuration 255 */ 256 #define CONFIG_SYS_CACHELINE_SIZE 16 257 258 #define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 259 CONFIG_SYS_INIT_RAM_SIZE - 8) 260 #define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 261 CONFIG_SYS_INIT_RAM_SIZE - 4) 262 #define CONFIG_SYS_ICACHE_INV (CF_CACR_BCINVA + CF_CACR_ICINVA + \ 263 CF_CACR_IDCM) 264 #define CONFIG_SYS_DCACHE_INV (CF_CACR_DCINVA) 265 #define CONFIG_SYS_CACHE_ACR2 (CONFIG_SYS_SDRAM_BASE | \ 266 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ 267 CF_ACR_EN | CF_ACR_SM_ALL) 268 #define CONFIG_SYS_CACHE_ICACR (CF_CACR_BEC | CF_CACR_BCINVA | \ 269 CF_CACR_IEC | CF_CACR_ICINVA) 270 #define CONFIG_SYS_CACHE_DCACR ((CONFIG_SYS_CACHE_ICACR | \ 271 CF_CACR_DEC | CF_CACR_DDCM_P | \ 272 CF_CACR_DCINVA) & ~CF_CACR_ICINVA) 273 274 /*----------------------------------------------------------------------- 275 * Chipselect bank definitions 276 */ 277 /* 278 * CS0 - NOR Flash 1, 2, 4, or 8MB 279 * CS1 - NOR Flash 280 * CS2 - Available 281 * CS3 - Available 282 * CS4 - Available 283 * CS5 - Available 284 */ 285 #define CONFIG_SYS_CS0_BASE 0xFF800000 286 #define CONFIG_SYS_CS0_MASK (((CONFIG_SYS_BOOTSZ << 20) - 1) & 0xFFFF0001) 287 #define CONFIG_SYS_CS0_CTRL 0x00101980 288 289 #ifdef CONFIG_SYS_NOR1SZ 290 #define CONFIG_SYS_CS1_BASE 0xE0000000 291 #define CONFIG_SYS_CS1_MASK (((CONFIG_SYS_NOR1SZ << 20) - 1) & 0xFFFF0001) 292 #define CONFIG_SYS_CS1_CTRL 0x00101D80 293 #endif 294 295 #endif /* _M5485EVB_H */ 296