1 /* 2 * Configuation settings for the Freescale MCF5485 FireEngine board. 3 * 4 * Copyright (C) 2004-2008 Freescale Semiconductor, Inc. 5 * TsiChung Liew (Tsi-Chung.Liew@freescale.com) 6 * 7 * SPDX-License-Identifier: GPL-2.0+ 8 */ 9 10 /* 11 * board/config.h - configuration options, board specific 12 */ 13 14 #ifndef _M5485EVB_H 15 #define _M5485EVB_H 16 17 /* 18 * High Level Configuration Options 19 * (easy to change) 20 */ 21 22 #define CONFIG_DISPLAY_BOARDINFO 23 24 #define CONFIG_MCFUART 25 #define CONFIG_SYS_UART_PORT (0) 26 #define CONFIG_BAUDRATE 115200 27 28 #undef CONFIG_HW_WATCHDOG 29 #define CONFIG_WATCHDOG_TIMEOUT 5000 /* timeout in milliseconds, max timeout is 6.71sec */ 30 31 /* Command line configuration */ 32 #include <config_cmd_default.h> 33 34 #define CONFIG_CMD_CACHE 35 #undef CONFIG_CMD_DATE 36 #define CONFIG_CMD_ELF 37 #define CONFIG_CMD_FLASH 38 #define CONFIG_CMD_I2C 39 #define CONFIG_CMD_MEMORY 40 #define CONFIG_CMD_MISC 41 #define CONFIG_CMD_MII 42 #define CONFIG_CMD_PCI 43 #define CONFIG_CMD_PING 44 #define CONFIG_CMD_REGINFO 45 #define CONFIG_CMD_USB 46 47 #define CONFIG_SLTTMR 48 49 #define CONFIG_FSLDMAFEC 50 #ifdef CONFIG_FSLDMAFEC 51 # define CONFIG_MII 1 52 # define CONFIG_MII_INIT 1 53 # define CONFIG_HAS_ETH1 54 55 # define CONFIG_SYS_DMA_USE_INTSRAM 1 56 # define CONFIG_SYS_DISCOVER_PHY 57 # define CONFIG_SYS_RX_ETH_BUFFER 32 58 # define CONFIG_SYS_TX_ETH_BUFFER 48 59 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 60 61 # define CONFIG_SYS_FEC0_PINMUX 0 62 # define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE 63 # define CONFIG_SYS_FEC1_PINMUX 0 64 # define CONFIG_SYS_FEC1_MIIBASE CONFIG_SYS_FEC0_IOBASE 65 66 # define MCFFEC_TOUT_LOOP 50000 67 /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */ 68 # ifndef CONFIG_SYS_DISCOVER_PHY 69 # define FECDUPLEX FULL 70 # define FECSPEED _100BASET 71 # else 72 # ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN 73 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 74 # endif 75 # endif /* CONFIG_SYS_DISCOVER_PHY */ 76 77 # define CONFIG_IPADDR 192.162.1.2 78 # define CONFIG_NETMASK 255.255.255.0 79 # define CONFIG_SERVERIP 192.162.1.1 80 # define CONFIG_GATEWAYIP 192.162.1.1 81 82 #endif 83 84 #ifdef CONFIG_CMD_USB 85 # define CONFIG_USB_STORAGE 86 # define CONFIG_DOS_PARTITION 87 # define CONFIG_USB_OHCI_NEW 88 # ifndef CONFIG_CMD_PCI 89 # define CONFIG_CMD_PCI 90 # endif 91 /*# define CONFIG_PCI_OHCI*/ 92 # define CONFIG_SYS_USB_OHCI_REGS_BASE 0x80041000 93 # define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 94 # define CONFIG_SYS_USB_OHCI_SLOT_NAME "isp1561" 95 # define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 96 #endif 97 98 /* I2C */ 99 #define CONFIG_SYS_I2C 100 #define CONFIG_SYS_I2C_FSL 101 #define CONFIG_SYS_FSL_I2C_SPEED 80000 102 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 103 #define CONFIG_SYS_FSL_I2C_OFFSET 0x00008F00 104 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR 105 106 /* PCI */ 107 #ifdef CONFIG_CMD_PCI 108 #define CONFIG_PCI 1 109 #define CONFIG_PCI_PNP 1 110 #define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1 111 112 #define CONFIG_SYS_PCI_MEM_BUS 0x80000000 113 #define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BUS 114 #define CONFIG_SYS_PCI_MEM_SIZE 0x10000000 115 116 #define CONFIG_SYS_PCI_IO_BUS 0x71000000 117 #define CONFIG_SYS_PCI_IO_PHYS CONFIG_SYS_PCI_IO_BUS 118 #define CONFIG_SYS_PCI_IO_SIZE 0x01000000 119 120 #define CONFIG_SYS_PCI_CFG_BUS 0x70000000 121 #define CONFIG_SYS_PCI_CFG_PHYS CONFIG_SYS_PCI_CFG_BUS 122 #define CONFIG_SYS_PCI_CFG_SIZE 0x01000000 123 #endif 124 125 #define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */ 126 #define CONFIG_UDP_CHECKSUM 127 128 #define CONFIG_HOSTNAME M548xEVB 129 #define CONFIG_EXTRA_ENV_SETTINGS \ 130 "netdev=eth0\0" \ 131 "loadaddr=10000\0" \ 132 "u-boot=u-boot.bin\0" \ 133 "load=tftp ${loadaddr) ${u-boot}\0" \ 134 "upd=run load; run prog\0" \ 135 "prog=prot off bank 1;" \ 136 "era ff800000 ff83ffff;" \ 137 "cp.b ${loadaddr} ff800000 ${filesize};"\ 138 "save\0" \ 139 "" 140 141 #define CONFIG_PRAM 512 /* 512 KB */ 142 #define CONFIG_SYS_PROMPT "-> " 143 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 144 145 #ifdef CONFIG_CMD_KGDB 146 # define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 147 #else 148 # define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 149 #endif 150 151 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 152 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 153 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 154 #define CONFIG_SYS_LOAD_ADDR 0x00010000 155 156 #define CONFIG_SYS_CLK CONFIG_SYS_BUSCLK 157 #define CONFIG_SYS_CPU_CLK CONFIG_SYS_CLK * 2 158 159 #define CONFIG_SYS_MBAR 0xF0000000 160 #define CONFIG_SYS_INTSRAM (CONFIG_SYS_MBAR + 0x10000) 161 #define CONFIG_SYS_INTSRAMSZ 0x8000 162 163 /*#define CONFIG_SYS_LATCH_ADDR (CONFIG_SYS_CS1_BASE + 0x80000)*/ 164 165 /* 166 * Low Level Configuration Settings 167 * (address mappings, register initial values, etc.) 168 * You should know what you are doing if you make changes here. 169 */ 170 /*----------------------------------------------------------------------- 171 * Definitions for initial stack pointer and data area (in DPRAM) 172 */ 173 #define CONFIG_SYS_INIT_RAM_ADDR 0xF2000000 174 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in internal SRAM */ 175 #define CONFIG_SYS_INIT_RAM_CTRL 0x21 176 #define CONFIG_SYS_INIT_RAM1_ADDR (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_RAM_SIZE) 177 #define CONFIG_SYS_INIT_RAM1_END 0x1000 /* End of used area in internal SRAM */ 178 #define CONFIG_SYS_INIT_RAM1_CTRL 0x21 179 #define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - 0x10) 180 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 181 182 /*----------------------------------------------------------------------- 183 * Start addresses for the final memory configuration 184 * (Set up by the startup code) 185 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 186 */ 187 #define CONFIG_SYS_SDRAM_BASE 0x00000000 188 #define CONFIG_SYS_SDRAM_CFG1 0x73711630 189 #define CONFIG_SYS_SDRAM_CFG2 0x46770000 190 #define CONFIG_SYS_SDRAM_CTRL 0xE10B0000 191 #define CONFIG_SYS_SDRAM_EMOD 0x40010000 192 #define CONFIG_SYS_SDRAM_MODE 0x018D0000 193 #define CONFIG_SYS_SDRAM_DRVSTRENGTH 0x000002AA 194 #ifdef CONFIG_SYS_DRAMSZ1 195 # define CONFIG_SYS_SDRAM_SIZE (CONFIG_SYS_DRAMSZ + CONFIG_SYS_DRAMSZ1) 196 #else 197 # define CONFIG_SYS_SDRAM_SIZE CONFIG_SYS_DRAMSZ 198 #endif 199 200 #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE + 0x400 201 #define CONFIG_SYS_MEMTEST_END ((CONFIG_SYS_SDRAM_SIZE - 3) << 20) 202 203 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) 204 #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ 205 206 #define CONFIG_SYS_BOOTPARAMS_LEN 64*1024 207 208 /* Reserve 256 kB for malloc() */ 209 #define CONFIG_SYS_MALLOC_LEN (256 << 10) 210 /* 211 * For booting Linux, the board info and command line data 212 * have to be in the first 8 MB of memory, since this is 213 * the maximum mapped by the Linux kernel during initialization ?? 214 */ 215 #define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20)) 216 217 /*----------------------------------------------------------------------- 218 * FLASH organization 219 */ 220 #define CONFIG_SYS_FLASH_CFI 221 #ifdef CONFIG_SYS_FLASH_CFI 222 # define CONFIG_SYS_FLASH_BASE (CONFIG_SYS_CS0_BASE) 223 # define CONFIG_FLASH_CFI_DRIVER 1 224 # define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT 225 # define CONFIG_SYS_MAX_FLASH_SECT 137 /* max number of sectors on one chip */ 226 # define CONFIG_SYS_FLASH_PROTECTION /* "Real" (hardware) sectors protection */ 227 # define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 228 #ifdef CONFIG_SYS_NOR1SZ 229 # define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ 230 # define CONFIG_SYS_FLASH_SIZE ((CONFIG_SYS_NOR1SZ + CONFIG_SYS_BOOTSZ) << 20) 231 # define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_CS0_BASE, CONFIG_SYS_CS1_BASE } 232 #else 233 # define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ 234 # define CONFIG_SYS_FLASH_SIZE (CONFIG_SYS_BOOTSZ << 20) 235 #endif 236 #endif 237 238 /* Configuration for environment 239 * Environment is not embedded in u-boot. First time runing may have env 240 * crc error warning if there is no correct environment on the flash. 241 */ 242 #define CONFIG_ENV_OFFSET 0x40000 243 #define CONFIG_ENV_SECT_SIZE 0x10000 244 #define CONFIG_ENV_IS_IN_FLASH 1 245 246 /*----------------------------------------------------------------------- 247 * Cache Configuration 248 */ 249 #define CONFIG_SYS_CACHELINE_SIZE 16 250 251 #define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 252 CONFIG_SYS_INIT_RAM_SIZE - 8) 253 #define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 254 CONFIG_SYS_INIT_RAM_SIZE - 4) 255 #define CONFIG_SYS_ICACHE_INV (CF_CACR_BCINVA + CF_CACR_ICINVA + \ 256 CF_CACR_IDCM) 257 #define CONFIG_SYS_DCACHE_INV (CF_CACR_DCINVA) 258 #define CONFIG_SYS_CACHE_ACR2 (CONFIG_SYS_SDRAM_BASE | \ 259 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ 260 CF_ACR_EN | CF_ACR_SM_ALL) 261 #define CONFIG_SYS_CACHE_ICACR (CF_CACR_BEC | CF_CACR_BCINVA | \ 262 CF_CACR_IEC | CF_CACR_ICINVA) 263 #define CONFIG_SYS_CACHE_DCACR ((CONFIG_SYS_CACHE_ICACR | \ 264 CF_CACR_DEC | CF_CACR_DDCM_P | \ 265 CF_CACR_DCINVA) & ~CF_CACR_ICINVA) 266 267 /*----------------------------------------------------------------------- 268 * Chipselect bank definitions 269 */ 270 /* 271 * CS0 - NOR Flash 1, 2, 4, or 8MB 272 * CS1 - NOR Flash 273 * CS2 - Available 274 * CS3 - Available 275 * CS4 - Available 276 * CS5 - Available 277 */ 278 #define CONFIG_SYS_CS0_BASE 0xFF800000 279 #define CONFIG_SYS_CS0_MASK (((CONFIG_SYS_BOOTSZ << 20) - 1) & 0xFFFF0001) 280 #define CONFIG_SYS_CS0_CTRL 0x00101980 281 282 #ifdef CONFIG_SYS_NOR1SZ 283 #define CONFIG_SYS_CS1_BASE 0xE0000000 284 #define CONFIG_SYS_CS1_MASK (((CONFIG_SYS_NOR1SZ << 20) - 1) & 0xFFFF0001) 285 #define CONFIG_SYS_CS1_CTRL 0x00101D80 286 #endif 287 288 #endif /* _M5485EVB_H */ 289