1 /* 2 * Configuation settings for the Freescale MCF5485 FireEngine board. 3 * 4 * Copyright (C) 2004-2008 Freescale Semiconductor, Inc. 5 * TsiChung Liew (Tsi-Chung.Liew@freescale.com) 6 * 7 * SPDX-License-Identifier: GPL-2.0+ 8 */ 9 10 /* 11 * board/config.h - configuration options, board specific 12 */ 13 14 #ifndef _M5485EVB_H 15 #define _M5485EVB_H 16 17 /* 18 * High Level Configuration Options 19 * (easy to change) 20 */ 21 22 #define CONFIG_DISPLAY_BOARDINFO 23 24 #define CONFIG_MCFUART 25 #define CONFIG_SYS_UART_PORT (0) 26 #define CONFIG_BAUDRATE 115200 27 28 #undef CONFIG_HW_WATCHDOG 29 #define CONFIG_WATCHDOG_TIMEOUT 5000 /* timeout in milliseconds, max timeout is 6.71sec */ 30 31 /* Command line configuration */ 32 #define CONFIG_CMD_CACHE 33 #undef CONFIG_CMD_DATE 34 #define CONFIG_CMD_I2C 35 #define CONFIG_CMD_MII 36 #define CONFIG_CMD_PCI 37 #define CONFIG_CMD_PING 38 #define CONFIG_CMD_REGINFO 39 #define CONFIG_CMD_USB 40 41 #define CONFIG_SLTTMR 42 43 #define CONFIG_FSLDMAFEC 44 #ifdef CONFIG_FSLDMAFEC 45 # define CONFIG_MII 1 46 # define CONFIG_MII_INIT 1 47 # define CONFIG_HAS_ETH1 48 49 # define CONFIG_SYS_DMA_USE_INTSRAM 1 50 # define CONFIG_SYS_DISCOVER_PHY 51 # define CONFIG_SYS_RX_ETH_BUFFER 32 52 # define CONFIG_SYS_TX_ETH_BUFFER 48 53 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 54 55 # define CONFIG_SYS_FEC0_PINMUX 0 56 # define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE 57 # define CONFIG_SYS_FEC1_PINMUX 0 58 # define CONFIG_SYS_FEC1_MIIBASE CONFIG_SYS_FEC0_IOBASE 59 60 # define MCFFEC_TOUT_LOOP 50000 61 /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */ 62 # ifndef CONFIG_SYS_DISCOVER_PHY 63 # define FECDUPLEX FULL 64 # define FECSPEED _100BASET 65 # else 66 # ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN 67 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 68 # endif 69 # endif /* CONFIG_SYS_DISCOVER_PHY */ 70 71 # define CONFIG_IPADDR 192.162.1.2 72 # define CONFIG_NETMASK 255.255.255.0 73 # define CONFIG_SERVERIP 192.162.1.1 74 # define CONFIG_GATEWAYIP 192.162.1.1 75 76 #endif 77 78 #ifdef CONFIG_CMD_USB 79 # define CONFIG_USB_STORAGE 80 # define CONFIG_DOS_PARTITION 81 # define CONFIG_USB_OHCI_NEW 82 # ifndef CONFIG_CMD_PCI 83 # define CONFIG_CMD_PCI 84 # endif 85 /*# define CONFIG_PCI_OHCI*/ 86 # define CONFIG_SYS_USB_OHCI_REGS_BASE 0x80041000 87 # define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 88 # define CONFIG_SYS_USB_OHCI_SLOT_NAME "isp1561" 89 # define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 90 #endif 91 92 /* I2C */ 93 #define CONFIG_SYS_I2C 94 #define CONFIG_SYS_I2C_FSL 95 #define CONFIG_SYS_FSL_I2C_SPEED 80000 96 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 97 #define CONFIG_SYS_FSL_I2C_OFFSET 0x00008F00 98 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR 99 100 /* PCI */ 101 #ifdef CONFIG_CMD_PCI 102 #define CONFIG_PCI 1 103 #define CONFIG_PCI_PNP 1 104 #define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1 105 106 #define CONFIG_SYS_PCI_MEM_BUS 0x80000000 107 #define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BUS 108 #define CONFIG_SYS_PCI_MEM_SIZE 0x10000000 109 110 #define CONFIG_SYS_PCI_IO_BUS 0x71000000 111 #define CONFIG_SYS_PCI_IO_PHYS CONFIG_SYS_PCI_IO_BUS 112 #define CONFIG_SYS_PCI_IO_SIZE 0x01000000 113 114 #define CONFIG_SYS_PCI_CFG_BUS 0x70000000 115 #define CONFIG_SYS_PCI_CFG_PHYS CONFIG_SYS_PCI_CFG_BUS 116 #define CONFIG_SYS_PCI_CFG_SIZE 0x01000000 117 #endif 118 119 #define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */ 120 #define CONFIG_UDP_CHECKSUM 121 122 #define CONFIG_HOSTNAME M548xEVB 123 #define CONFIG_EXTRA_ENV_SETTINGS \ 124 "netdev=eth0\0" \ 125 "loadaddr=10000\0" \ 126 "u-boot=u-boot.bin\0" \ 127 "load=tftp ${loadaddr) ${u-boot}\0" \ 128 "upd=run load; run prog\0" \ 129 "prog=prot off bank 1;" \ 130 "era ff800000 ff83ffff;" \ 131 "cp.b ${loadaddr} ff800000 ${filesize};"\ 132 "save\0" \ 133 "" 134 135 #define CONFIG_PRAM 512 /* 512 KB */ 136 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 137 138 #ifdef CONFIG_CMD_KGDB 139 # define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 140 #else 141 # define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 142 #endif 143 144 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 145 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 146 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 147 #define CONFIG_SYS_LOAD_ADDR 0x00010000 148 149 #define CONFIG_SYS_CLK CONFIG_SYS_BUSCLK 150 #define CONFIG_SYS_CPU_CLK CONFIG_SYS_CLK * 2 151 152 #define CONFIG_SYS_MBAR 0xF0000000 153 #define CONFIG_SYS_INTSRAM (CONFIG_SYS_MBAR + 0x10000) 154 #define CONFIG_SYS_INTSRAMSZ 0x8000 155 156 /*#define CONFIG_SYS_LATCH_ADDR (CONFIG_SYS_CS1_BASE + 0x80000)*/ 157 158 /* 159 * Low Level Configuration Settings 160 * (address mappings, register initial values, etc.) 161 * You should know what you are doing if you make changes here. 162 */ 163 /*----------------------------------------------------------------------- 164 * Definitions for initial stack pointer and data area (in DPRAM) 165 */ 166 #define CONFIG_SYS_INIT_RAM_ADDR 0xF2000000 167 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in internal SRAM */ 168 #define CONFIG_SYS_INIT_RAM_CTRL 0x21 169 #define CONFIG_SYS_INIT_RAM1_ADDR (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_RAM_SIZE) 170 #define CONFIG_SYS_INIT_RAM1_END 0x1000 /* End of used area in internal SRAM */ 171 #define CONFIG_SYS_INIT_RAM1_CTRL 0x21 172 #define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - 0x10) 173 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 174 175 /*----------------------------------------------------------------------- 176 * Start addresses for the final memory configuration 177 * (Set up by the startup code) 178 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 179 */ 180 #define CONFIG_SYS_SDRAM_BASE 0x00000000 181 #define CONFIG_SYS_SDRAM_CFG1 0x73711630 182 #define CONFIG_SYS_SDRAM_CFG2 0x46770000 183 #define CONFIG_SYS_SDRAM_CTRL 0xE10B0000 184 #define CONFIG_SYS_SDRAM_EMOD 0x40010000 185 #define CONFIG_SYS_SDRAM_MODE 0x018D0000 186 #define CONFIG_SYS_SDRAM_DRVSTRENGTH 0x000002AA 187 #ifdef CONFIG_SYS_DRAMSZ1 188 # define CONFIG_SYS_SDRAM_SIZE (CONFIG_SYS_DRAMSZ + CONFIG_SYS_DRAMSZ1) 189 #else 190 # define CONFIG_SYS_SDRAM_SIZE CONFIG_SYS_DRAMSZ 191 #endif 192 193 #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE + 0x400 194 #define CONFIG_SYS_MEMTEST_END ((CONFIG_SYS_SDRAM_SIZE - 3) << 20) 195 196 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) 197 #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ 198 199 #define CONFIG_SYS_BOOTPARAMS_LEN 64*1024 200 201 /* Reserve 256 kB for malloc() */ 202 #define CONFIG_SYS_MALLOC_LEN (256 << 10) 203 /* 204 * For booting Linux, the board info and command line data 205 * have to be in the first 8 MB of memory, since this is 206 * the maximum mapped by the Linux kernel during initialization ?? 207 */ 208 #define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20)) 209 210 /*----------------------------------------------------------------------- 211 * FLASH organization 212 */ 213 #define CONFIG_SYS_FLASH_CFI 214 #ifdef CONFIG_SYS_FLASH_CFI 215 # define CONFIG_SYS_FLASH_BASE (CONFIG_SYS_CS0_BASE) 216 # define CONFIG_FLASH_CFI_DRIVER 1 217 # define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT 218 # define CONFIG_SYS_MAX_FLASH_SECT 137 /* max number of sectors on one chip */ 219 # define CONFIG_SYS_FLASH_PROTECTION /* "Real" (hardware) sectors protection */ 220 # define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 221 #ifdef CONFIG_SYS_NOR1SZ 222 # define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ 223 # define CONFIG_SYS_FLASH_SIZE ((CONFIG_SYS_NOR1SZ + CONFIG_SYS_BOOTSZ) << 20) 224 # define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_CS0_BASE, CONFIG_SYS_CS1_BASE } 225 #else 226 # define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ 227 # define CONFIG_SYS_FLASH_SIZE (CONFIG_SYS_BOOTSZ << 20) 228 #endif 229 #endif 230 231 /* Configuration for environment 232 * Environment is not embedded in u-boot. First time runing may have env 233 * crc error warning if there is no correct environment on the flash. 234 */ 235 #define CONFIG_ENV_OFFSET 0x40000 236 #define CONFIG_ENV_SECT_SIZE 0x10000 237 #define CONFIG_ENV_IS_IN_FLASH 1 238 239 /*----------------------------------------------------------------------- 240 * Cache Configuration 241 */ 242 #define CONFIG_SYS_CACHELINE_SIZE 16 243 244 #define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 245 CONFIG_SYS_INIT_RAM_SIZE - 8) 246 #define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 247 CONFIG_SYS_INIT_RAM_SIZE - 4) 248 #define CONFIG_SYS_ICACHE_INV (CF_CACR_BCINVA + CF_CACR_ICINVA + \ 249 CF_CACR_IDCM) 250 #define CONFIG_SYS_DCACHE_INV (CF_CACR_DCINVA) 251 #define CONFIG_SYS_CACHE_ACR2 (CONFIG_SYS_SDRAM_BASE | \ 252 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ 253 CF_ACR_EN | CF_ACR_SM_ALL) 254 #define CONFIG_SYS_CACHE_ICACR (CF_CACR_BEC | CF_CACR_BCINVA | \ 255 CF_CACR_IEC | CF_CACR_ICINVA) 256 #define CONFIG_SYS_CACHE_DCACR ((CONFIG_SYS_CACHE_ICACR | \ 257 CF_CACR_DEC | CF_CACR_DDCM_P | \ 258 CF_CACR_DCINVA) & ~CF_CACR_ICINVA) 259 260 /*----------------------------------------------------------------------- 261 * Chipselect bank definitions 262 */ 263 /* 264 * CS0 - NOR Flash 1, 2, 4, or 8MB 265 * CS1 - NOR Flash 266 * CS2 - Available 267 * CS3 - Available 268 * CS4 - Available 269 * CS5 - Available 270 */ 271 #define CONFIG_SYS_CS0_BASE 0xFF800000 272 #define CONFIG_SYS_CS0_MASK (((CONFIG_SYS_BOOTSZ << 20) - 1) & 0xFFFF0001) 273 #define CONFIG_SYS_CS0_CTRL 0x00101980 274 275 #ifdef CONFIG_SYS_NOR1SZ 276 #define CONFIG_SYS_CS1_BASE 0xE0000000 277 #define CONFIG_SYS_CS1_MASK (((CONFIG_SYS_NOR1SZ << 20) - 1) & 0xFFFF0001) 278 #define CONFIG_SYS_CS1_CTRL 0x00101D80 279 #endif 280 281 #endif /* _M5485EVB_H */ 282