xref: /openbmc/u-boot/include/configs/M5475EVB.h (revision fea7f3aa)
1 /*
2  * Configuation settings for the Freescale MCF5475 board.
3  *
4  * Copyright (C) 2004-2008 Freescale Semiconductor, Inc.
5  * TsiChung Liew (Tsi-Chung.Liew@freescale.com)
6  *
7  * SPDX-License-Identifier:	GPL-2.0+
8  */
9 
10 /*
11  * board/config.h - configuration options, board specific
12  */
13 
14 #ifndef _M5475EVB_H
15 #define _M5475EVB_H
16 
17 /*
18  * High Level Configuration Options
19  * (easy to change)
20  */
21 
22 #define CONFIG_DISPLAY_BOARDINFO
23 
24 #define CONFIG_MCFUART
25 #define CONFIG_SYS_UART_PORT		(0)
26 #define CONFIG_BAUDRATE		115200
27 
28 #undef CONFIG_HW_WATCHDOG
29 #define CONFIG_WATCHDOG_TIMEOUT	5000	/* timeout in milliseconds, max timeout is 6.71sec */
30 
31 /* Command line configuration */
32 #define CONFIG_CMD_CACHE
33 #undef CONFIG_CMD_DATE
34 #define CONFIG_CMD_I2C
35 #define CONFIG_CMD_MII
36 #define CONFIG_CMD_PCI
37 #define CONFIG_CMD_PING
38 #define CONFIG_CMD_REGINFO
39 #define CONFIG_CMD_USB
40 
41 #define CONFIG_SLTTMR
42 
43 #define CONFIG_FSLDMAFEC
44 #ifdef CONFIG_FSLDMAFEC
45 #	define CONFIG_MII		1
46 #	define CONFIG_MII_INIT		1
47 #	define CONFIG_HAS_ETH1
48 
49 #	define CONFIG_SYS_DMA_USE_INTSRAM	1
50 #	define CONFIG_SYS_DISCOVER_PHY
51 #	define CONFIG_SYS_RX_ETH_BUFFER	32
52 #	define CONFIG_SYS_TX_ETH_BUFFER	48
53 #	define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
54 
55 #	define CONFIG_SYS_FEC0_PINMUX		0
56 #	define CONFIG_SYS_FEC0_MIIBASE		CONFIG_SYS_FEC0_IOBASE
57 #	define CONFIG_SYS_FEC1_PINMUX		0
58 #	define CONFIG_SYS_FEC1_MIIBASE		CONFIG_SYS_FEC0_IOBASE
59 
60 #	define MCFFEC_TOUT_LOOP		50000
61 /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
62 #	ifndef CONFIG_SYS_DISCOVER_PHY
63 #		define FECDUPLEX	FULL
64 #		define FECSPEED		_100BASET
65 #	else
66 #		ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
67 #			define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
68 #		endif
69 #	endif			/* CONFIG_SYS_DISCOVER_PHY */
70 
71 #	define CONFIG_IPADDR	192.162.1.2
72 #	define CONFIG_NETMASK	255.255.255.0
73 #	define CONFIG_SERVERIP	192.162.1.1
74 #	define CONFIG_GATEWAYIP	192.162.1.1
75 
76 #endif
77 
78 #ifdef CONFIG_CMD_USB
79 #	define CONFIG_USB_OHCI_NEW
80 #	define CONFIG_USB_STORAGE
81 
82 #	ifndef CONFIG_CMD_PCI
83 #		define CONFIG_CMD_PCI
84 #	endif
85 #	define CONFIG_PCI_OHCI
86 #	define CONFIG_DOS_PARTITION
87 
88 #	undef CONFIG_SYS_USB_OHCI_BOARD_INIT
89 #	undef CONFIG_SYS_USB_OHCI_CPU_INIT
90 #	define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS	15
91 #	define CONFIG_SYS_USB_OHCI_SLOT_NAME		"isp1561"
92 #	define CONFIG_SYS_OHCI_SWAP_REG_ACCESS
93 #endif
94 
95 /* I2C */
96 #define CONFIG_SYS_I2C
97 #define CONFIG_SYS_I2C_FSL
98 #define CONFIG_SYS_FSL_I2C_SPEED	80000
99 #define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
100 #define CONFIG_SYS_FSL_I2C_OFFSET	0x00008F00
101 #define CONFIG_SYS_IMMR		CONFIG_SYS_MBAR
102 
103 /* PCI */
104 #ifdef CONFIG_CMD_PCI
105 #define CONFIG_PCI		1
106 #define CONFIG_PCI_PNP		1
107 #define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE	1
108 
109 #define CONFIG_SYS_PCI_CACHE_LINE_SIZE	8
110 
111 #define CONFIG_SYS_PCI_MEM_BUS		0x80000000
112 #define CONFIG_SYS_PCI_MEM_PHYS	CONFIG_SYS_PCI_MEM_BUS
113 #define CONFIG_SYS_PCI_MEM_SIZE	0x10000000
114 
115 #define CONFIG_SYS_PCI_IO_BUS		0x71000000
116 #define CONFIG_SYS_PCI_IO_PHYS		CONFIG_SYS_PCI_IO_BUS
117 #define CONFIG_SYS_PCI_IO_SIZE		0x01000000
118 
119 #define CONFIG_SYS_PCI_CFG_BUS		0x70000000
120 #define CONFIG_SYS_PCI_CFG_PHYS	CONFIG_SYS_PCI_CFG_BUS
121 #define CONFIG_SYS_PCI_CFG_SIZE	0x01000000
122 #endif
123 
124 #define CONFIG_BOOTDELAY	1	/* autoboot after 5 seconds */
125 #define CONFIG_UDP_CHECKSUM
126 
127 #ifdef CONFIG_MCFFEC
128 #	define CONFIG_IPADDR	192.162.1.2
129 #	define CONFIG_NETMASK	255.255.255.0
130 #	define CONFIG_SERVERIP	192.162.1.1
131 #	define CONFIG_GATEWAYIP	192.162.1.1
132 #endif				/* FEC_ENET */
133 
134 #define CONFIG_HOSTNAME		M547xEVB
135 #define CONFIG_EXTRA_ENV_SETTINGS		\
136 	"netdev=eth0\0"				\
137 	"loadaddr=10000\0"			\
138 	"u-boot=u-boot.bin\0"			\
139 	"load=tftp ${loadaddr) ${u-boot}\0"	\
140 	"upd=run load; run prog\0"		\
141 	"prog=prot off bank 1;"			\
142 	"era ff800000 ff83ffff;"		\
143 	"cp.b ${loadaddr} ff800000 ${filesize};"\
144 	"save\0"				\
145 	""
146 
147 #define CONFIG_PRAM		512	/* 512 KB */
148 #define CONFIG_SYS_LONGHELP		/* undef to save memory */
149 
150 #ifdef CONFIG_CMD_KGDB
151 #	define CONFIG_SYS_CBSIZE	1024	/* Console I/O Buffer Size */
152 #else
153 #	define CONFIG_SYS_CBSIZE	256	/* Console I/O Buffer Size */
154 #endif
155 
156 #define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size */
157 #define CONFIG_SYS_MAXARGS		16	/* max number of command args */
158 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size    */
159 #define CONFIG_SYS_LOAD_ADDR		0x00010000
160 
161 #define CONFIG_SYS_CLK			CONFIG_SYS_BUSCLK
162 #define CONFIG_SYS_CPU_CLK		CONFIG_SYS_CLK * 2
163 
164 #define CONFIG_SYS_MBAR		0xF0000000
165 #define CONFIG_SYS_INTSRAM		(CONFIG_SYS_MBAR + 0x10000)
166 #define CONFIG_SYS_INTSRAMSZ		0x8000
167 
168 /*#define CONFIG_SYS_LATCH_ADDR		(CONFIG_SYS_CS1_BASE + 0x80000)*/
169 
170 /*
171  * Low Level Configuration Settings
172  * (address mappings, register initial values, etc.)
173  * You should know what you are doing if you make changes here.
174  */
175 /*-----------------------------------------------------------------------
176  * Definitions for initial stack pointer and data area (in DPRAM)
177  */
178 #define CONFIG_SYS_INIT_RAM_ADDR	0xF2000000
179 #define CONFIG_SYS_INIT_RAM_SIZE	0x1000	/* Size of used area in internal SRAM */
180 #define CONFIG_SYS_INIT_RAM_CTRL	0x21
181 #define CONFIG_SYS_INIT_RAM1_ADDR	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_RAM_SIZE)
182 #define CONFIG_SYS_INIT_RAM1_END	0x1000	/* End of used area in internal SRAM */
183 #define CONFIG_SYS_INIT_RAM1_CTRL	0x21
184 #define CONFIG_SYS_GBL_DATA_OFFSET	((CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - 0x10)
185 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
186 
187 /*-----------------------------------------------------------------------
188  * Start addresses for the final memory configuration
189  * (Set up by the startup code)
190  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
191  */
192 #define CONFIG_SYS_SDRAM_BASE		0x00000000
193 #define CONFIG_SYS_SDRAM_CFG1		0x73711630
194 #define CONFIG_SYS_SDRAM_CFG2		0x46770000
195 #define CONFIG_SYS_SDRAM_CTRL		0xE10B0000
196 #define CONFIG_SYS_SDRAM_EMOD		0x40010000
197 #define CONFIG_SYS_SDRAM_MODE		0x018D0000
198 #define CONFIG_SYS_SDRAM_DRVSTRENGTH	0x000002AA
199 #ifdef CONFIG_SYS_DRAMSZ1
200 #	define CONFIG_SYS_SDRAM_SIZE	(CONFIG_SYS_DRAMSZ + CONFIG_SYS_DRAMSZ1)
201 #else
202 #	define CONFIG_SYS_SDRAM_SIZE	CONFIG_SYS_DRAMSZ
203 #endif
204 
205 #define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE + 0x400
206 #define CONFIG_SYS_MEMTEST_END		((CONFIG_SYS_SDRAM_SIZE - 3) << 20)
207 
208 #define CONFIG_SYS_MONITOR_BASE	(CONFIG_SYS_FLASH_BASE + 0x400)
209 #define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor */
210 
211 #define CONFIG_SYS_BOOTPARAMS_LEN	64*1024
212 
213 /* Reserve 256 kB for malloc() */
214 #define CONFIG_SYS_MALLOC_LEN		(256 << 10)
215 /*
216  * For booting Linux, the board info and command line data
217  * have to be in the first 8 MB of memory, since this is
218  * the maximum mapped by the Linux kernel during initialization ??
219  */
220 #define CONFIG_SYS_BOOTMAPSZ		(CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
221 
222 /*-----------------------------------------------------------------------
223  * FLASH organization
224  */
225 #define CONFIG_SYS_FLASH_CFI
226 #ifdef CONFIG_SYS_FLASH_CFI
227 #	define CONFIG_SYS_FLASH_BASE		(CONFIG_SYS_CS0_BASE)
228 #	define CONFIG_FLASH_CFI_DRIVER	1
229 #	define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
230 #	define CONFIG_SYS_MAX_FLASH_SECT	137	/* max number of sectors on one chip */
231 #	define CONFIG_SYS_FLASH_PROTECTION	/* "Real" (hardware) sectors protection */
232 #	define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
233 #ifdef CONFIG_SYS_NOR1SZ
234 #	define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of memory banks */
235 #	define CONFIG_SYS_FLASH_SIZE		((CONFIG_SYS_NOR1SZ + CONFIG_SYS_BOOTSZ) << 20)
236 #	define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_CS0_BASE, CONFIG_SYS_CS1_BASE }
237 #else
238 #	define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks */
239 #	define CONFIG_SYS_FLASH_SIZE		(CONFIG_SYS_BOOTSZ << 20)
240 #endif
241 #endif
242 
243 /* Configuration for environment
244  * Environment is not embedded in u-boot but at offset 0x40000 on the flash.
245  * First time runing may have env crc error warning if there is
246  * no correct environment on the flash.
247  */
248 #define CONFIG_ENV_OFFSET		0x40000
249 #define CONFIG_ENV_SECT_SIZE	0x10000
250 #define CONFIG_ENV_IS_IN_FLASH	1
251 
252 /*-----------------------------------------------------------------------
253  * Cache Configuration
254  */
255 #define CONFIG_SYS_CACHELINE_SIZE	16
256 
257 #define ICACHE_STATUS			(CONFIG_SYS_INIT_RAM_ADDR + \
258 					 CONFIG_SYS_INIT_RAM_SIZE - 8)
259 #define DCACHE_STATUS			(CONFIG_SYS_INIT_RAM_ADDR + \
260 					 CONFIG_SYS_INIT_RAM_SIZE - 4)
261 #define CONFIG_SYS_ICACHE_INV		(CF_CACR_BCINVA + CF_CACR_ICINVA + \
262 					 CF_CACR_IDCM)
263 #define CONFIG_SYS_DCACHE_INV		(CF_CACR_DCINVA)
264 #define CONFIG_SYS_CACHE_ACR2		(CONFIG_SYS_SDRAM_BASE | \
265 					 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
266 					 CF_ACR_EN | CF_ACR_SM_ALL)
267 #define CONFIG_SYS_CACHE_ICACR		(CF_CACR_BEC | CF_CACR_BCINVA | \
268 					 CF_CACR_IEC | CF_CACR_ICINVA)
269 #define CONFIG_SYS_CACHE_DCACR		((CONFIG_SYS_CACHE_ICACR | \
270 					 CF_CACR_DEC | CF_CACR_DDCM_P | \
271 					 CF_CACR_DCINVA) & ~CF_CACR_ICINVA)
272 
273 /*-----------------------------------------------------------------------
274  * Chipselect bank definitions
275  */
276 /*
277  * CS0 - NOR Flash 1, 2, 4, or 8MB
278  * CS1 - NOR Flash
279  * CS2 - Available
280  * CS3 - Available
281  * CS4 - Available
282  * CS5 - Available
283  */
284 #define CONFIG_SYS_CS0_BASE		0xFF800000
285 #define CONFIG_SYS_CS0_MASK		(((CONFIG_SYS_BOOTSZ << 20) - 1) & 0xFFFF0001)
286 #define CONFIG_SYS_CS0_CTRL		0x00101980
287 
288 #ifdef CONFIG_SYS_NOR1SZ
289 #define CONFIG_SYS_CS1_BASE		0xE0000000
290 #define CONFIG_SYS_CS1_MASK		(((CONFIG_SYS_NOR1SZ << 20) - 1) & 0xFFFF0001)
291 #define CONFIG_SYS_CS1_CTRL		0x00101D80
292 #endif
293 
294 #endif				/* _M5475EVB_H */
295