1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Configuation settings for the Freescale MCF5475 board. 4 * 5 * Copyright (C) 2004-2008 Freescale Semiconductor, Inc. 6 * TsiChung Liew (Tsi-Chung.Liew@freescale.com) 7 */ 8 9 /* 10 * board/config.h - configuration options, board specific 11 */ 12 13 #ifndef _M5475EVB_H 14 #define _M5475EVB_H 15 16 /* 17 * High Level Configuration Options 18 * (easy to change) 19 */ 20 21 #define CONFIG_MCFUART 22 #define CONFIG_SYS_UART_PORT (0) 23 24 #undef CONFIG_HW_WATCHDOG 25 #define CONFIG_WATCHDOG_TIMEOUT 5000 /* timeout in milliseconds, max timeout is 6.71sec */ 26 27 #define CONFIG_SLTTMR 28 29 #define CONFIG_FSLDMAFEC 30 #ifdef CONFIG_FSLDMAFEC 31 # define CONFIG_MII_INIT 1 32 # define CONFIG_HAS_ETH1 33 34 # define CONFIG_SYS_DMA_USE_INTSRAM 1 35 # define CONFIG_SYS_DISCOVER_PHY 36 # define CONFIG_SYS_RX_ETH_BUFFER 32 37 # define CONFIG_SYS_TX_ETH_BUFFER 48 38 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 39 40 # define CONFIG_SYS_FEC0_PINMUX 0 41 # define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE 42 # define CONFIG_SYS_FEC1_PINMUX 0 43 # define CONFIG_SYS_FEC1_MIIBASE CONFIG_SYS_FEC0_IOBASE 44 45 # define MCFFEC_TOUT_LOOP 50000 46 /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */ 47 # ifndef CONFIG_SYS_DISCOVER_PHY 48 # define FECDUPLEX FULL 49 # define FECSPEED _100BASET 50 # else 51 # ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN 52 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 53 # endif 54 # endif /* CONFIG_SYS_DISCOVER_PHY */ 55 56 # define CONFIG_IPADDR 192.162.1.2 57 # define CONFIG_NETMASK 255.255.255.0 58 # define CONFIG_SERVERIP 192.162.1.1 59 # define CONFIG_GATEWAYIP 192.162.1.1 60 61 #endif 62 63 #ifdef CONFIG_CMD_USB 64 # define CONFIG_USB_OHCI_NEW 65 66 # define CONFIG_PCI_OHCI 67 68 # undef CONFIG_SYS_USB_OHCI_BOARD_INIT 69 # undef CONFIG_SYS_USB_OHCI_CPU_INIT 70 # define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 71 # define CONFIG_SYS_USB_OHCI_SLOT_NAME "isp1561" 72 # define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 73 #endif 74 75 /* I2C */ 76 #define CONFIG_SYS_I2C 77 #define CONFIG_SYS_I2C_FSL 78 #define CONFIG_SYS_FSL_I2C_SPEED 80000 79 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 80 #define CONFIG_SYS_FSL_I2C_OFFSET 0x00008F00 81 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR 82 83 /* PCI */ 84 #ifdef CONFIG_CMD_PCI 85 #define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1 86 87 #define CONFIG_SYS_PCI_CACHE_LINE_SIZE 8 88 89 #define CONFIG_SYS_PCI_MEM_BUS 0x80000000 90 #define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BUS 91 #define CONFIG_SYS_PCI_MEM_SIZE 0x10000000 92 93 #define CONFIG_SYS_PCI_IO_BUS 0x71000000 94 #define CONFIG_SYS_PCI_IO_PHYS CONFIG_SYS_PCI_IO_BUS 95 #define CONFIG_SYS_PCI_IO_SIZE 0x01000000 96 97 #define CONFIG_SYS_PCI_CFG_BUS 0x70000000 98 #define CONFIG_SYS_PCI_CFG_PHYS CONFIG_SYS_PCI_CFG_BUS 99 #define CONFIG_SYS_PCI_CFG_SIZE 0x01000000 100 #endif 101 102 #define CONFIG_UDP_CHECKSUM 103 104 #ifdef CONFIG_MCFFEC 105 # define CONFIG_IPADDR 192.162.1.2 106 # define CONFIG_NETMASK 255.255.255.0 107 # define CONFIG_SERVERIP 192.162.1.1 108 # define CONFIG_GATEWAYIP 192.162.1.1 109 #endif /* FEC_ENET */ 110 111 #define CONFIG_HOSTNAME "M547xEVB" 112 #define CONFIG_EXTRA_ENV_SETTINGS \ 113 "netdev=eth0\0" \ 114 "loadaddr=10000\0" \ 115 "u-boot=u-boot.bin\0" \ 116 "load=tftp ${loadaddr) ${u-boot}\0" \ 117 "upd=run load; run prog\0" \ 118 "prog=prot off bank 1;" \ 119 "era ff800000 ff83ffff;" \ 120 "cp.b ${loadaddr} ff800000 ${filesize};"\ 121 "save\0" \ 122 "" 123 124 #define CONFIG_PRAM 512 /* 512 KB */ 125 126 #define CONFIG_SYS_LOAD_ADDR 0x00010000 127 128 #define CONFIG_SYS_CLK CONFIG_SYS_BUSCLK 129 #define CONFIG_SYS_CPU_CLK CONFIG_SYS_CLK * 2 130 131 #define CONFIG_SYS_MBAR 0xF0000000 132 #define CONFIG_SYS_INTSRAM (CONFIG_SYS_MBAR + 0x10000) 133 #define CONFIG_SYS_INTSRAMSZ 0x8000 134 135 /*#define CONFIG_SYS_LATCH_ADDR (CONFIG_SYS_CS1_BASE + 0x80000)*/ 136 137 /* 138 * Low Level Configuration Settings 139 * (address mappings, register initial values, etc.) 140 * You should know what you are doing if you make changes here. 141 */ 142 /*----------------------------------------------------------------------- 143 * Definitions for initial stack pointer and data area (in DPRAM) 144 */ 145 #define CONFIG_SYS_INIT_RAM_ADDR 0xF2000000 146 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in internal SRAM */ 147 #define CONFIG_SYS_INIT_RAM_CTRL 0x21 148 #define CONFIG_SYS_INIT_RAM1_ADDR (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_RAM_SIZE) 149 #define CONFIG_SYS_INIT_RAM1_END 0x1000 /* End of used area in internal SRAM */ 150 #define CONFIG_SYS_INIT_RAM1_CTRL 0x21 151 #define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - 0x10) 152 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 153 154 /*----------------------------------------------------------------------- 155 * Start addresses for the final memory configuration 156 * (Set up by the startup code) 157 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 158 */ 159 #define CONFIG_SYS_SDRAM_BASE 0x00000000 160 #define CONFIG_SYS_SDRAM_CFG1 0x73711630 161 #define CONFIG_SYS_SDRAM_CFG2 0x46770000 162 #define CONFIG_SYS_SDRAM_CTRL 0xE10B0000 163 #define CONFIG_SYS_SDRAM_EMOD 0x40010000 164 #define CONFIG_SYS_SDRAM_MODE 0x018D0000 165 #define CONFIG_SYS_SDRAM_DRVSTRENGTH 0x000002AA 166 #ifdef CONFIG_SYS_DRAMSZ1 167 # define CONFIG_SYS_SDRAM_SIZE (CONFIG_SYS_DRAMSZ + CONFIG_SYS_DRAMSZ1) 168 #else 169 # define CONFIG_SYS_SDRAM_SIZE CONFIG_SYS_DRAMSZ 170 #endif 171 172 #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE + 0x400 173 #define CONFIG_SYS_MEMTEST_END ((CONFIG_SYS_SDRAM_SIZE - 3) << 20) 174 175 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) 176 #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ 177 178 #define CONFIG_SYS_BOOTPARAMS_LEN 64*1024 179 180 /* Reserve 256 kB for malloc() */ 181 #define CONFIG_SYS_MALLOC_LEN (256 << 10) 182 /* 183 * For booting Linux, the board info and command line data 184 * have to be in the first 8 MB of memory, since this is 185 * the maximum mapped by the Linux kernel during initialization ?? 186 */ 187 #define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20)) 188 189 /*----------------------------------------------------------------------- 190 * FLASH organization 191 */ 192 #ifdef CONFIG_SYS_FLASH_CFI 193 # define CONFIG_SYS_FLASH_BASE (CONFIG_SYS_CS0_BASE) 194 # define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT 195 # define CONFIG_SYS_MAX_FLASH_SECT 137 /* max number of sectors on one chip */ 196 #ifdef CONFIG_SYS_NOR1SZ 197 # define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ 198 # define CONFIG_SYS_FLASH_SIZE ((CONFIG_SYS_NOR1SZ + CONFIG_SYS_BOOTSZ) << 20) 199 # define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_CS0_BASE, CONFIG_SYS_CS1_BASE } 200 #else 201 # define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ 202 # define CONFIG_SYS_FLASH_SIZE (CONFIG_SYS_BOOTSZ << 20) 203 #endif 204 #endif 205 206 /* Configuration for environment 207 * Environment is not embedded in u-boot but at offset 0x40000 on the flash. 208 * First time runing may have env crc error warning if there is 209 * no correct environment on the flash. 210 */ 211 #define CONFIG_ENV_OFFSET 0x40000 212 #define CONFIG_ENV_SECT_SIZE 0x10000 213 214 /*----------------------------------------------------------------------- 215 * Cache Configuration 216 */ 217 #define CONFIG_SYS_CACHELINE_SIZE 16 218 219 #define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 220 CONFIG_SYS_INIT_RAM_SIZE - 8) 221 #define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 222 CONFIG_SYS_INIT_RAM_SIZE - 4) 223 #define CONFIG_SYS_ICACHE_INV (CF_CACR_BCINVA + CF_CACR_ICINVA + \ 224 CF_CACR_IDCM) 225 #define CONFIG_SYS_DCACHE_INV (CF_CACR_DCINVA) 226 #define CONFIG_SYS_CACHE_ACR2 (CONFIG_SYS_SDRAM_BASE | \ 227 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ 228 CF_ACR_EN | CF_ACR_SM_ALL) 229 #define CONFIG_SYS_CACHE_ICACR (CF_CACR_BEC | CF_CACR_BCINVA | \ 230 CF_CACR_IEC | CF_CACR_ICINVA) 231 #define CONFIG_SYS_CACHE_DCACR ((CONFIG_SYS_CACHE_ICACR | \ 232 CF_CACR_DEC | CF_CACR_DDCM_P | \ 233 CF_CACR_DCINVA) & ~CF_CACR_ICINVA) 234 235 /*----------------------------------------------------------------------- 236 * Chipselect bank definitions 237 */ 238 /* 239 * CS0 - NOR Flash 1, 2, 4, or 8MB 240 * CS1 - NOR Flash 241 * CS2 - Available 242 * CS3 - Available 243 * CS4 - Available 244 * CS5 - Available 245 */ 246 #define CONFIG_SYS_CS0_BASE 0xFF800000 247 #define CONFIG_SYS_CS0_MASK (((CONFIG_SYS_BOOTSZ << 20) - 1) & 0xFFFF0001) 248 #define CONFIG_SYS_CS0_CTRL 0x00101980 249 250 #ifdef CONFIG_SYS_NOR1SZ 251 #define CONFIG_SYS_CS1_BASE 0xE0000000 252 #define CONFIG_SYS_CS1_MASK (((CONFIG_SYS_NOR1SZ << 20) - 1) & 0xFFFF0001) 253 #define CONFIG_SYS_CS1_CTRL 0x00101D80 254 #endif 255 256 #endif /* _M5475EVB_H */ 257