xref: /openbmc/u-boot/include/configs/M5475EVB.h (revision 1500389c)
1 /*
2  * Configuation settings for the Freescale MCF5475 board.
3  *
4  * Copyright (C) 2004-2008 Freescale Semiconductor, Inc.
5  * TsiChung Liew (Tsi-Chung.Liew@freescale.com)
6  *
7  * SPDX-License-Identifier:	GPL-2.0+
8  */
9 
10 /*
11  * board/config.h - configuration options, board specific
12  */
13 
14 #ifndef _M5475EVB_H
15 #define _M5475EVB_H
16 
17 /*
18  * High Level Configuration Options
19  * (easy to change)
20  */
21 #define CONFIG_MCF547x_8x	/* define processor family */
22 #define CONFIG_M547x		/* define processor type */
23 #define CONFIG_M5475		/* define processor type */
24 
25 #define CONFIG_MCFUART
26 #define CONFIG_SYS_UART_PORT		(0)
27 #define CONFIG_BAUDRATE		115200
28 
29 #define CONFIG_HW_WATCHDOG
30 #define CONFIG_WATCHDOG_TIMEOUT	5000	/* timeout in milliseconds, max timeout is 6.71sec */
31 
32 /* Command line configuration */
33 #include <config_cmd_default.h>
34 
35 #define CONFIG_CMD_CACHE
36 #undef CONFIG_CMD_DATE
37 #define CONFIG_CMD_ELF
38 #define CONFIG_CMD_FLASH
39 #define CONFIG_CMD_I2C
40 #define CONFIG_CMD_MEMORY
41 #define CONFIG_CMD_MISC
42 #define CONFIG_CMD_MII
43 #define CONFIG_CMD_NET
44 #define CONFIG_CMD_PCI
45 #define CONFIG_CMD_PING
46 #define CONFIG_CMD_REGINFO
47 #define CONFIG_CMD_USB
48 
49 #define CONFIG_SLTTMR
50 
51 #define CONFIG_FSLDMAFEC
52 #ifdef CONFIG_FSLDMAFEC
53 #	define CONFIG_MII		1
54 #	define CONFIG_MII_INIT		1
55 #	define CONFIG_HAS_ETH1
56 
57 #	define CONFIG_SYS_DMA_USE_INTSRAM	1
58 #	define CONFIG_SYS_DISCOVER_PHY
59 #	define CONFIG_SYS_RX_ETH_BUFFER	32
60 #	define CONFIG_SYS_TX_ETH_BUFFER	48
61 #	define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
62 
63 #	define CONFIG_SYS_FEC0_PINMUX		0
64 #	define CONFIG_SYS_FEC0_MIIBASE		CONFIG_SYS_FEC0_IOBASE
65 #	define CONFIG_SYS_FEC1_PINMUX		0
66 #	define CONFIG_SYS_FEC1_MIIBASE		CONFIG_SYS_FEC0_IOBASE
67 
68 #	define MCFFEC_TOUT_LOOP		50000
69 /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
70 #	ifndef CONFIG_SYS_DISCOVER_PHY
71 #		define FECDUPLEX	FULL
72 #		define FECSPEED		_100BASET
73 #	else
74 #		ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
75 #			define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
76 #		endif
77 #	endif			/* CONFIG_SYS_DISCOVER_PHY */
78 
79 #	define CONFIG_ETHADDR	00:e0:0c:bc:e5:60
80 #	define CONFIG_ETH1ADDR	00:e0:0c:bc:e5:61
81 #	define CONFIG_IPADDR	192.162.1.2
82 #	define CONFIG_NETMASK	255.255.255.0
83 #	define CONFIG_SERVERIP	192.162.1.1
84 #	define CONFIG_GATEWAYIP	192.162.1.1
85 #	define CONFIG_OVERWRITE_ETHADDR_ONCE
86 
87 #endif
88 
89 #ifdef CONFIG_CMD_USB
90 #	define CONFIG_USB_OHCI_NEW
91 #	define CONFIG_USB_STORAGE
92 
93 #	ifndef CONFIG_CMD_PCI
94 #		define CONFIG_CMD_PCI
95 #	endif
96 #	define CONFIG_PCI_OHCI
97 #	define CONFIG_DOS_PARTITION
98 
99 #	undef CONFIG_SYS_USB_OHCI_BOARD_INIT
100 #	undef CONFIG_SYS_USB_OHCI_CPU_INIT
101 #	define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS	15
102 #	define CONFIG_SYS_USB_OHCI_SLOT_NAME		"isp1561"
103 #	define CONFIG_SYS_OHCI_SWAP_REG_ACCESS
104 #endif
105 
106 /* I2C */
107 #define CONFIG_SYS_I2C
108 #define CONFIG_SYS_I2C_FSL
109 #define CONFIG_SYS_FSL_I2C_SPEED	80000
110 #define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
111 #define CONFIG_SYS_FSL_I2C_OFFSET	0x00008F00
112 #define CONFIG_SYS_IMMR		CONFIG_SYS_MBAR
113 
114 /* PCI */
115 #ifdef CONFIG_CMD_PCI
116 #define CONFIG_PCI		1
117 #define CONFIG_PCI_PNP		1
118 #define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE	1
119 
120 #define CONFIG_SYS_PCI_CACHE_LINE_SIZE	8
121 
122 #define CONFIG_SYS_PCI_MEM_BUS		0x80000000
123 #define CONFIG_SYS_PCI_MEM_PHYS	CONFIG_SYS_PCI_MEM_BUS
124 #define CONFIG_SYS_PCI_MEM_SIZE	0x10000000
125 
126 #define CONFIG_SYS_PCI_IO_BUS		0x71000000
127 #define CONFIG_SYS_PCI_IO_PHYS		CONFIG_SYS_PCI_IO_BUS
128 #define CONFIG_SYS_PCI_IO_SIZE		0x01000000
129 
130 #define CONFIG_SYS_PCI_CFG_BUS		0x70000000
131 #define CONFIG_SYS_PCI_CFG_PHYS	CONFIG_SYS_PCI_CFG_BUS
132 #define CONFIG_SYS_PCI_CFG_SIZE	0x01000000
133 #endif
134 
135 #define CONFIG_BOOTDELAY	1	/* autoboot after 5 seconds */
136 #define CONFIG_UDP_CHECKSUM
137 
138 #ifdef CONFIG_MCFFEC
139 #	define CONFIG_ETHADDR	00:e0:0c:bc:e5:60
140 #	define CONFIG_IPADDR	192.162.1.2
141 #	define CONFIG_NETMASK	255.255.255.0
142 #	define CONFIG_SERVERIP	192.162.1.1
143 #	define CONFIG_GATEWAYIP	192.162.1.1
144 #	define CONFIG_OVERWRITE_ETHADDR_ONCE
145 #endif				/* FEC_ENET */
146 
147 #define CONFIG_HOSTNAME		M547xEVB
148 #define CONFIG_EXTRA_ENV_SETTINGS		\
149 	"netdev=eth0\0"				\
150 	"loadaddr=10000\0"			\
151 	"u-boot=u-boot.bin\0"			\
152 	"load=tftp ${loadaddr) ${u-boot}\0"	\
153 	"upd=run load; run prog\0"		\
154 	"prog=prot off bank 1;"			\
155 	"era ff800000 ff83ffff;"		\
156 	"cp.b ${loadaddr} ff800000 ${filesize};"\
157 	"save\0"				\
158 	""
159 
160 #define CONFIG_PRAM		512	/* 512 KB */
161 #define CONFIG_SYS_PROMPT		"-> "
162 #define CONFIG_SYS_LONGHELP		/* undef to save memory */
163 
164 #ifdef CONFIG_CMD_KGDB
165 #	define CONFIG_SYS_CBSIZE	1024	/* Console I/O Buffer Size */
166 #else
167 #	define CONFIG_SYS_CBSIZE	256	/* Console I/O Buffer Size */
168 #endif
169 
170 #define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size */
171 #define CONFIG_SYS_MAXARGS		16	/* max number of command args */
172 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size    */
173 #define CONFIG_SYS_LOAD_ADDR		0x00010000
174 
175 #define CONFIG_SYS_CLK			CONFIG_SYS_BUSCLK
176 #define CONFIG_SYS_CPU_CLK		CONFIG_SYS_CLK * 2
177 
178 #define CONFIG_SYS_MBAR		0xF0000000
179 #define CONFIG_SYS_INTSRAM		(CONFIG_SYS_MBAR + 0x10000)
180 #define CONFIG_SYS_INTSRAMSZ		0x8000
181 
182 /*#define CONFIG_SYS_LATCH_ADDR		(CONFIG_SYS_CS1_BASE + 0x80000)*/
183 
184 /*
185  * Low Level Configuration Settings
186  * (address mappings, register initial values, etc.)
187  * You should know what you are doing if you make changes here.
188  */
189 /*-----------------------------------------------------------------------
190  * Definitions for initial stack pointer and data area (in DPRAM)
191  */
192 #define CONFIG_SYS_INIT_RAM_ADDR	0xF2000000
193 #define CONFIG_SYS_INIT_RAM_SIZE	0x1000	/* Size of used area in internal SRAM */
194 #define CONFIG_SYS_INIT_RAM_CTRL	0x21
195 #define CONFIG_SYS_INIT_RAM1_ADDR	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_RAM_SIZE)
196 #define CONFIG_SYS_INIT_RAM1_END	0x1000	/* End of used area in internal SRAM */
197 #define CONFIG_SYS_INIT_RAM1_CTRL	0x21
198 #define CONFIG_SYS_GBL_DATA_OFFSET	((CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - 0x10)
199 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
200 
201 /*-----------------------------------------------------------------------
202  * Start addresses for the final memory configuration
203  * (Set up by the startup code)
204  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
205  */
206 #define CONFIG_SYS_SDRAM_BASE		0x00000000
207 #define CONFIG_SYS_SDRAM_CFG1		0x73711630
208 #define CONFIG_SYS_SDRAM_CFG2		0x46770000
209 #define CONFIG_SYS_SDRAM_CTRL		0xE10B0000
210 #define CONFIG_SYS_SDRAM_EMOD		0x40010000
211 #define CONFIG_SYS_SDRAM_MODE		0x018D0000
212 #define CONFIG_SYS_SDRAM_DRVSTRENGTH	0x000002AA
213 #ifdef CONFIG_SYS_DRAMSZ1
214 #	define CONFIG_SYS_SDRAM_SIZE	(CONFIG_SYS_DRAMSZ + CONFIG_SYS_DRAMSZ1)
215 #else
216 #	define CONFIG_SYS_SDRAM_SIZE	CONFIG_SYS_DRAMSZ
217 #endif
218 
219 #define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE + 0x400
220 #define CONFIG_SYS_MEMTEST_END		((CONFIG_SYS_SDRAM_SIZE - 3) << 20)
221 
222 #define CONFIG_SYS_MONITOR_BASE	(CONFIG_SYS_FLASH_BASE + 0x400)
223 #define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor */
224 
225 #define CONFIG_SYS_BOOTPARAMS_LEN	64*1024
226 
227 /* Reserve 256 kB for malloc() */
228 #define CONFIG_SYS_MALLOC_LEN		(256 << 10)
229 /*
230  * For booting Linux, the board info and command line data
231  * have to be in the first 8 MB of memory, since this is
232  * the maximum mapped by the Linux kernel during initialization ??
233  */
234 #define CONFIG_SYS_BOOTMAPSZ		(CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
235 
236 /*-----------------------------------------------------------------------
237  * FLASH organization
238  */
239 #define CONFIG_SYS_FLASH_CFI
240 #ifdef CONFIG_SYS_FLASH_CFI
241 #	define CONFIG_SYS_FLASH_BASE		(CONFIG_SYS_CS0_BASE)
242 #	define CONFIG_FLASH_CFI_DRIVER	1
243 #	define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
244 #	define CONFIG_SYS_MAX_FLASH_SECT	137	/* max number of sectors on one chip */
245 #	define CONFIG_SYS_FLASH_PROTECTION	/* "Real" (hardware) sectors protection */
246 #	define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
247 #ifdef CONFIG_SYS_NOR1SZ
248 #	define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of memory banks */
249 #	define CONFIG_SYS_FLASH_SIZE		((CONFIG_SYS_NOR1SZ + CONFIG_SYS_BOOTSZ) << 20)
250 #	define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_CS0_BASE, CONFIG_SYS_CS1_BASE }
251 #else
252 #	define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks */
253 #	define CONFIG_SYS_FLASH_SIZE		(CONFIG_SYS_BOOTSZ << 20)
254 #endif
255 #endif
256 
257 /* Configuration for environment
258  * Environment is not embedded in u-boot but at offset 0x40000 on the flash.
259  * First time runing may have env crc error warning if there is
260  * no correct environment on the flash.
261  */
262 #define CONFIG_ENV_OFFSET		0x40000
263 #define CONFIG_ENV_SECT_SIZE	0x10000
264 #define CONFIG_ENV_IS_IN_FLASH	1
265 
266 /*-----------------------------------------------------------------------
267  * Cache Configuration
268  */
269 #define CONFIG_SYS_CACHELINE_SIZE	16
270 
271 #define ICACHE_STATUS			(CONFIG_SYS_INIT_RAM_ADDR + \
272 					 CONFIG_SYS_INIT_RAM_SIZE - 8)
273 #define DCACHE_STATUS			(CONFIG_SYS_INIT_RAM_ADDR + \
274 					 CONFIG_SYS_INIT_RAM_SIZE - 4)
275 #define CONFIG_SYS_ICACHE_INV		(CF_CACR_BCINVA + CF_CACR_ICINVA + \
276 					 CF_CACR_IDCM)
277 #define CONFIG_SYS_DCACHE_INV		(CF_CACR_DCINVA)
278 #define CONFIG_SYS_CACHE_ACR2		(CONFIG_SYS_SDRAM_BASE | \
279 					 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
280 					 CF_ACR_EN | CF_ACR_SM_ALL)
281 #define CONFIG_SYS_CACHE_ICACR		(CF_CACR_BEC | CF_CACR_BCINVA | \
282 					 CF_CACR_IEC | CF_CACR_ICINVA)
283 #define CONFIG_SYS_CACHE_DCACR		((CONFIG_SYS_CACHE_ICACR | \
284 					 CF_CACR_DEC | CF_CACR_DDCM_P | \
285 					 CF_CACR_DCINVA) & ~CF_CACR_ICINVA)
286 
287 /*-----------------------------------------------------------------------
288  * Chipselect bank definitions
289  */
290 /*
291  * CS0 - NOR Flash 1, 2, 4, or 8MB
292  * CS1 - NOR Flash
293  * CS2 - Available
294  * CS3 - Available
295  * CS4 - Available
296  * CS5 - Available
297  */
298 #define CONFIG_SYS_CS0_BASE		0xFF800000
299 #define CONFIG_SYS_CS0_MASK		(((CONFIG_SYS_BOOTSZ << 20) - 1) & 0xFFFF0001)
300 #define CONFIG_SYS_CS0_CTRL		0x00101980
301 
302 #ifdef CONFIG_SYS_NOR1SZ
303 #define CONFIG_SYS_CS1_BASE		0xE0000000
304 #define CONFIG_SYS_CS1_MASK		(((CONFIG_SYS_NOR1SZ << 20) - 1) & 0xFFFF0001)
305 #define CONFIG_SYS_CS1_CTRL		0x00101D80
306 #endif
307 
308 #endif				/* _M5475EVB_H */
309