1 /* 2 * Configuation settings for the Freescale MCF54451 EVB board. 3 * 4 * Copyright (C) 2004-2008 Freescale Semiconductor, Inc. 5 * TsiChung Liew (Tsi-Chung.Liew@freescale.com) 6 * 7 * SPDX-License-Identifier: GPL-2.0+ 8 */ 9 10 /* 11 * board/config.h - configuration options, board specific 12 */ 13 14 #ifndef _M54451EVB_H 15 #define _M54451EVB_H 16 17 /* 18 * High Level Configuration Options 19 * (easy to change) 20 */ 21 #define CONFIG_M54451EVB /* M54451EVB board */ 22 23 #define CONFIG_DISPLAY_BOARDINFO 24 25 #define CONFIG_MCFUART 26 #define CONFIG_SYS_UART_PORT (0) 27 #define CONFIG_BAUDRATE 115200 28 29 #undef CONFIG_WATCHDOG 30 31 #define CONFIG_TIMESTAMP /* Print image info with timestamp */ 32 33 /* 34 * BOOTP options 35 */ 36 #define CONFIG_BOOTP_BOOTFILESIZE 37 #define CONFIG_BOOTP_BOOTPATH 38 #define CONFIG_BOOTP_GATEWAY 39 #define CONFIG_BOOTP_HOSTNAME 40 41 /* Command line configuration */ 42 #include <config_cmd_default.h> 43 44 #define CONFIG_CMD_BOOTD 45 #define CONFIG_CMD_CACHE 46 #define CONFIG_CMD_DATE 47 #define CONFIG_CMD_DHCP 48 #define CONFIG_CMD_ELF 49 #define CONFIG_CMD_FLASH 50 #define CONFIG_CMD_I2C 51 #undef CONFIG_CMD_JFFS2 52 #define CONFIG_CMD_MEMORY 53 #define CONFIG_CMD_MISC 54 #define CONFIG_CMD_MII 55 #define CONFIG_CMD_NFS 56 #define CONFIG_CMD_PING 57 #define CONFIG_CMD_REGINFO 58 #define CONFIG_CMD_SPI 59 #define CONFIG_CMD_SF 60 61 #undef CONFIG_CMD_LOADB 62 #undef CONFIG_CMD_LOADS 63 64 /* Network configuration */ 65 #define CONFIG_MCFFEC 66 #ifdef CONFIG_MCFFEC 67 # define CONFIG_MII 1 68 # define CONFIG_MII_INIT 1 69 # define CONFIG_SYS_DISCOVER_PHY 70 # define CONFIG_SYS_RX_ETH_BUFFER 8 71 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 72 73 # define CONFIG_SYS_FEC0_PINMUX 0 74 # define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE 75 # define MCFFEC_TOUT_LOOP 50000 76 77 # define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */ 78 # define CONFIG_BOOTARGS "root=/dev/mtdblock1 rw rootfstype=jffs2 ip=none mtdparts=physmap-flash.0:2M(kernel)ro,-(jffs2)" 79 # define CONFIG_ETHPRIME "FEC0" 80 # define CONFIG_IPADDR 192.162.1.2 81 # define CONFIG_NETMASK 255.255.255.0 82 # define CONFIG_SERVERIP 192.162.1.1 83 # define CONFIG_GATEWAYIP 192.162.1.1 84 85 /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */ 86 # ifndef CONFIG_SYS_DISCOVER_PHY 87 # define FECDUPLEX FULL 88 # define FECSPEED _100BASET 89 # else 90 # ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN 91 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 92 # endif 93 # endif /* CONFIG_SYS_DISCOVER_PHY */ 94 #endif 95 96 #define CONFIG_HOSTNAME M54451EVB 97 #ifdef CONFIG_SYS_STMICRO_BOOT 98 /* ST Micro serial flash */ 99 #define CONFIG_SYS_LOAD_ADDR2 0x40010007 100 #define CONFIG_EXTRA_ENV_SETTINGS \ 101 "netdev=eth0\0" \ 102 "inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0" \ 103 "loadaddr=0x40010000\0" \ 104 "sbfhdr=sbfhdr.bin\0" \ 105 "uboot=u-boot.bin\0" \ 106 "load=tftp ${loadaddr} ${sbfhdr};" \ 107 "tftp " __stringify(CONFIG_SYS_LOAD_ADDR2) " ${uboot} \0" \ 108 "upd=run load; run prog\0" \ 109 "prog=sf probe 0:1 1000000 3;" \ 110 "sf erase 0 30000;" \ 111 "sf write ${loadaddr} 0 30000;" \ 112 "save\0" \ 113 "" 114 #else 115 #define CONFIG_SYS_UBOOT_END 0x3FFFF 116 #define CONFIG_EXTRA_ENV_SETTINGS \ 117 "netdev=eth0\0" \ 118 "inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0" \ 119 "loadaddr=40010000\0" \ 120 "u-boot=u-boot.bin\0" \ 121 "load=tftp ${loadaddr) ${u-boot}\0" \ 122 "upd=run load; run prog\0" \ 123 "prog=prot off 0 " __stringify(CONFIG_SYS_UBOOT_END) \ 124 "; era 0 " __stringify(CONFIG_SYS_UBOOT_END) " ;" \ 125 "cp.b ${loadaddr} 0 ${filesize};" \ 126 "save\0" \ 127 "" 128 #endif 129 130 /* Realtime clock */ 131 #define CONFIG_MCFRTC 132 #undef RTC_DEBUG 133 #define CONFIG_SYS_RTC_OSCILLATOR (32 * CONFIG_SYS_HZ) 134 135 /* Timer */ 136 #define CONFIG_MCFTMR 137 #undef CONFIG_MCFPIT 138 139 /* I2c */ 140 #define CONFIG_SYS_I2C 141 #define CONFIG_SYS_I2C_FSL 142 #define CONFIG_SYS_FSL_I2C_SPEED 80000 143 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 144 #define CONFIG_SYS_FSL_I2C_OFFSET 0x58000 145 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR 146 147 /* DSPI and Serial Flash */ 148 #define CONFIG_CF_SPI 149 #define CONFIG_CF_DSPI 150 #define CONFIG_SERIAL_FLASH 151 #define CONFIG_HARD_SPI 152 #define CONFIG_SYS_SBFHDR_SIZE 0x7 153 #ifdef CONFIG_CMD_SPI 154 # define CONFIG_SPI_FLASH_STMICRO 155 156 # define CONFIG_SYS_DSPI_CTAR0 (DSPI_CTAR_TRSZ(7) | \ 157 DSPI_CTAR_PCSSCK_1CLK | \ 158 DSPI_CTAR_PASC(0) | \ 159 DSPI_CTAR_PDT(0) | \ 160 DSPI_CTAR_CSSCK(0) | \ 161 DSPI_CTAR_ASC(0) | \ 162 DSPI_CTAR_DT(1)) 163 # define CONFIG_SYS_DSPI_CTAR1 (CONFIG_SYS_DSPI_CTAR0) 164 # define CONFIG_SYS_DSPI_CTAR2 (CONFIG_SYS_DSPI_CTAR0) 165 #endif 166 167 /* Input, PCI, Flexbus, and VCO */ 168 #define CONFIG_EXTRA_CLOCK 169 170 #define CONFIG_PRAM 2048 /* 2048 KB */ 171 172 #define CONFIG_SYS_PROMPT "-> " 173 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 174 175 #if defined(CONFIG_CMD_KGDB) 176 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 177 #else 178 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 179 #endif 180 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 181 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 182 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 183 184 #define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x10000) 185 186 #define CONFIG_SYS_MBAR 0xFC000000 187 188 /* 189 * Low Level Configuration Settings 190 * (address mappings, register initial values, etc.) 191 * You should know what you are doing if you make changes here. 192 */ 193 194 /*----------------------------------------------------------------------- 195 * Definitions for initial stack pointer and data area (in DPRAM) 196 */ 197 #define CONFIG_SYS_INIT_RAM_ADDR 0x80000000 198 #define CONFIG_SYS_INIT_RAM_SIZE 0x8000 /* Size of used area in internal SRAM */ 199 #define CONFIG_SYS_INIT_RAM_CTRL 0x221 200 #define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - 32) 201 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 202 #define CONFIG_SYS_SBFHDR_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - 32) 203 204 /*----------------------------------------------------------------------- 205 * Start addresses for the final memory configuration 206 * (Set up by the startup code) 207 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 208 */ 209 #define CONFIG_SYS_SDRAM_BASE 0x40000000 210 #define CONFIG_SYS_SDRAM_SIZE 128 /* SDRAM size in MB */ 211 #define CONFIG_SYS_SDRAM_CFG1 0x33633F30 212 #define CONFIG_SYS_SDRAM_CFG2 0x57670000 213 #define CONFIG_SYS_SDRAM_CTRL 0xE20D2C00 214 #define CONFIG_SYS_SDRAM_EMOD 0x80810000 215 #define CONFIG_SYS_SDRAM_MODE 0x008D0000 216 #define CONFIG_SYS_SDRAM_DRV_STRENGTH 0x44 217 218 #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE + 0x400 219 #define CONFIG_SYS_MEMTEST_END ((CONFIG_SYS_SDRAM_SIZE - 3) << 20) 220 221 #ifdef CONFIG_CF_SBF 222 # define CONFIG_SERIAL_BOOT 223 # define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_TEXT_BASE + 0x400) 224 #else 225 # define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) 226 #endif 227 #define CONFIG_SYS_BOOTPARAMS_LEN 64*1024 228 #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ 229 230 /* Reserve 256 kB for malloc() */ 231 #define CONFIG_SYS_MALLOC_LEN (256 << 10) 232 /* 233 * For booting Linux, the board info and command line data 234 * have to be in the first 8 MB of memory, since this is 235 * the maximum mapped by the Linux kernel during initialization ?? 236 */ 237 /* Initial Memory map for Linux */ 238 #define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20)) 239 240 /* Configuration for environment 241 * Environment is not embedded in u-boot. First time runing may have env 242 * crc error warning if there is no correct environment on the flash. 243 */ 244 #if defined(CONFIG_SYS_STMICRO_BOOT) 245 # define CONFIG_ENV_IS_IN_SPI_FLASH 1 246 # define CONFIG_ENV_SPI_CS 1 247 # define CONFIG_ENV_OFFSET 0x20000 248 # define CONFIG_ENV_SIZE 0x2000 249 # define CONFIG_ENV_SECT_SIZE 0x10000 250 #else 251 # define CONFIG_ENV_IS_IN_FLASH 1 252 # define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x40000) 253 # define CONFIG_ENV_SIZE 0x2000 254 # define CONFIG_ENV_SECT_SIZE 0x20000 255 #endif 256 #undef CONFIG_ENV_OVERWRITE 257 258 /* FLASH organization */ 259 #define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE 260 261 #define CONFIG_SYS_FLASH_CFI 262 #ifdef CONFIG_SYS_FLASH_CFI 263 264 # define CONFIG_FLASH_CFI_DRIVER 1 265 # define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 266 # define CONFIG_SYS_FLASH_SIZE 0x1000000 /* Max size that the board might have */ 267 # define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT 268 # define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ 269 # define CONFIG_SYS_MAX_FLASH_SECT 137 /* max number of sectors on one chip */ 270 # define CONFIG_SYS_FLASH_PROTECTION /* "Real" (hardware) sectors protection */ 271 # define CONFIG_SYS_FLASH_CHECKSUM 272 # define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_CS0_BASE } 273 274 #endif 275 276 /* 277 * This is setting for JFFS2 support in u-boot. 278 * NOTE: Enable CONFIG_CMD_JFFS2 for JFFS2 support. 279 */ 280 #ifdef CONFIG_CMD_JFFS2 281 # define CONFIG_JFFS2_DEV "nor0" 282 # define CONFIG_JFFS2_PART_SIZE 0x01000000 283 # define CONFIG_JFFS2_PART_OFFSET (CONFIG_SYS_FLASH0_BASE + 0x500000) 284 #endif 285 286 /* Cache Configuration */ 287 #define CONFIG_SYS_CACHELINE_SIZE 16 288 289 #define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 290 CONFIG_SYS_INIT_RAM_SIZE - 8) 291 #define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 292 CONFIG_SYS_INIT_RAM_SIZE - 4) 293 #define CONFIG_SYS_ICACHE_INV (CF_CACR_BCINVA + CF_CACR_ICINVA) 294 #define CONFIG_SYS_DCACHE_INV (CF_CACR_DCINVA) 295 #define CONFIG_SYS_CACHE_ACR2 (CONFIG_SYS_SDRAM_BASE | \ 296 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ 297 CF_ACR_EN | CF_ACR_SM_ALL) 298 #define CONFIG_SYS_CACHE_ICACR (CF_CACR_BEC | CF_CACR_IEC | \ 299 CF_CACR_ICINVA | CF_CACR_EUSP) 300 #define CONFIG_SYS_CACHE_DCACR ((CONFIG_SYS_CACHE_ICACR | \ 301 CF_CACR_DEC | CF_CACR_DDCM_P | \ 302 CF_CACR_DCINVA) & ~CF_CACR_ICINVA) 303 304 /*----------------------------------------------------------------------- 305 * Memory bank definitions 306 */ 307 /* 308 * CS0 - NOR Flash 16MB 309 * CS1 - Available 310 * CS2 - Available 311 * CS3 - Available 312 * CS4 - Available 313 * CS5 - Available 314 */ 315 316 /* Flash */ 317 #define CONFIG_SYS_CS0_BASE 0x00000000 318 #define CONFIG_SYS_CS0_MASK 0x00FF0001 319 #define CONFIG_SYS_CS0_CTRL 0x00004D80 320 321 #define CONFIG_SYS_SPANSION_BASE CONFIG_SYS_CS0_BASE 322 323 #endif /* _M54451EVB_H */ 324