1 /* 2 * Configuation settings for the Freescale MCF54418 TWR board. 3 * 4 * Copyright 2010-2012 Freescale Semiconductor, Inc. 5 * TsiChung Liew (Tsi-Chung.Liew@freescale.com) 6 * 7 * SPDX-License-Identifier: GPL-2.0+ 8 */ 9 10 /* 11 * board/config.h - configuration options, board specific 12 */ 13 14 #ifndef _M54418TWR_H 15 #define _M54418TWR_H 16 17 /* 18 * High Level Configuration Options 19 * (easy to change) 20 */ 21 #define CONFIG_M54418TWR /* M54418TWR board */ 22 23 #define CONFIG_MCFUART 24 #define CONFIG_SYS_UART_PORT (0) 25 #define CONFIG_SYS_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } 26 27 #define LDS_BOARD_TEXT board/freescale/m54418twr/sbf_dram_init.o (.text*) 28 29 #undef CONFIG_WATCHDOG 30 31 #define CONFIG_TIMESTAMP /* Print image info with timestamp */ 32 33 /* 34 * BOOTP options 35 */ 36 #define CONFIG_BOOTP_BOOTFILESIZE 37 #define CONFIG_BOOTP_BOOTPATH 38 #define CONFIG_BOOTP_GATEWAY 39 #define CONFIG_BOOTP_HOSTNAME 40 41 /* 42 * NAND FLASH 43 */ 44 #ifdef CONFIG_CMD_NAND 45 #define CONFIG_JFFS2_NAND 46 #define CONFIG_NAND_FSL_NFC 47 #define CONFIG_SYS_NAND_BASE 0xFC0FC000 48 #define CONFIG_SYS_MAX_NAND_DEVICE 1 49 #define NAND_MAX_CHIPS CONFIG_SYS_MAX_NAND_DEVICE 50 #define CONFIG_SYS_NAND_SELECT_DEVICE 51 #endif 52 53 /* Network configuration */ 54 #define CONFIG_MCFFEC 55 #ifdef CONFIG_MCFFEC 56 #define CONFIG_MII 1 57 #define CONFIG_MII_INIT 1 58 #define CONFIG_SYS_DISCOVER_PHY 59 #define CONFIG_SYS_RX_ETH_BUFFER 2 60 #define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 61 #define CONFIG_SYS_TX_ETH_BUFFER 2 62 #define CONFIG_HAS_ETH1 63 64 #define CONFIG_SYS_FEC0_PINMUX 0 65 #define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE 66 #define CONFIG_SYS_FEC1_PINMUX 0 67 #define CONFIG_SYS_FEC1_MIIBASE CONFIG_SYS_FEC0_MIIBASE 68 #define MCFFEC_TOUT_LOOP 50000 69 #define CONFIG_SYS_FEC0_PHYADDR 0 70 #define CONFIG_SYS_FEC1_PHYADDR 1 71 72 #define CONFIG_ETHPRIME "FEC0" 73 #define CONFIG_IPADDR 192.168.1.2 74 #define CONFIG_NETMASK 255.255.255.0 75 #define CONFIG_SERVERIP 192.168.1.1 76 #define CONFIG_GATEWAYIP 192.168.1.1 77 78 #define CONFIG_SYS_FEC_BUF_USE_SRAM 79 /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */ 80 #ifndef CONFIG_SYS_DISCOVER_PHY 81 #define FECDUPLEX FULL 82 #define FECSPEED _100BASET 83 #define LINKSTATUS 1 84 #else 85 #define LINKSTATUS 0 86 #ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN 87 #define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 88 #endif 89 #endif /* CONFIG_SYS_DISCOVER_PHY */ 90 #endif 91 92 #define CONFIG_HOSTNAME M54418TWR 93 94 #if defined(CONFIG_CF_SBF) 95 /* ST Micro serial flash */ 96 #define CONFIG_SYS_LOAD_ADDR2 0x40010007 97 #define CONFIG_EXTRA_ENV_SETTINGS \ 98 "netdev=eth0\0" \ 99 "inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0" \ 100 "loadaddr=0x40010000\0" \ 101 "sbfhdr=sbfhdr.bin\0" \ 102 "uboot=u-boot.bin\0" \ 103 "load=tftp ${loadaddr} ${sbfhdr};" \ 104 "tftp " __stringify(CONFIG_SYS_LOAD_ADDR2) " ${uboot} \0" \ 105 "upd=run load; run prog\0" \ 106 "prog=sf probe 0:1 1000000 3;" \ 107 "sf erase 0 40000;" \ 108 "sf write ${loadaddr} 0 40000;" \ 109 "save\0" \ 110 "" 111 #elif defined(CONFIG_SYS_NAND_BOOT) 112 #define CONFIG_EXTRA_ENV_SETTINGS \ 113 "netdev=eth0\0" \ 114 "inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0" \ 115 "loadaddr=0x40010000\0" \ 116 "u-boot=u-boot.bin\0" \ 117 "load=tftp ${loadaddr} ${u-boot};\0" \ 118 "upd=run load; run prog\0" \ 119 "prog=nand device 0;" \ 120 "nand erase 0 40000;" \ 121 "nb_update ${loadaddr} ${filesize};" \ 122 "save\0" \ 123 "" 124 #else 125 #define CONFIG_SYS_UBOOT_END 0x3FFFF 126 #define CONFIG_EXTRA_ENV_SETTINGS \ 127 "netdev=eth0\0" \ 128 "inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0" \ 129 "loadaddr=40010000\0" \ 130 "u-boot=u-boot.bin\0" \ 131 "load=tftp ${loadaddr) ${u-boot}\0" \ 132 "upd=run load; run prog\0" \ 133 "prog=prot off mram" " ;" \ 134 "cp.b ${loadaddr} 0 ${filesize};" \ 135 "save\0" \ 136 "" 137 #endif 138 139 /* Realtime clock */ 140 #undef CONFIG_MCFRTC 141 #define CONFIG_RTC_MCFRRTC 142 #define CONFIG_SYS_MCFRRTC_BASE 0xFC0A8000 143 144 /* Timer */ 145 #define CONFIG_MCFTMR 146 #undef CONFIG_MCFPIT 147 148 /* I2c */ 149 #undef CONFIG_SYS_FSL_I2C 150 #undef CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ 151 /* I2C speed and slave address */ 152 #define CONFIG_SYS_I2C_SPEED 80000 153 #define CONFIG_SYS_I2C_SLAVE 0x7F 154 #define CONFIG_SYS_I2C_OFFSET 0x58000 155 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR 156 157 /* DSPI and Serial Flash */ 158 #define CONFIG_CF_SPI 159 #define CONFIG_CF_DSPI 160 #define CONFIG_SERIAL_FLASH 161 #define CONFIG_HARD_SPI 162 #define CONFIG_SYS_SBFHDR_SIZE 0x7 163 #ifdef CONFIG_CMD_SPI 164 165 # define CONFIG_SYS_DSPI_CTAR0 (DSPI_CTAR_TRSZ(7) | \ 166 DSPI_CTAR_PCSSCK_1CLK | \ 167 DSPI_CTAR_PASC(0) | \ 168 DSPI_CTAR_PDT(0) | \ 169 DSPI_CTAR_CSSCK(0) | \ 170 DSPI_CTAR_ASC(0) | \ 171 DSPI_CTAR_DT(1)) 172 # define CONFIG_SYS_DSPI_CTAR1 (CONFIG_SYS_DSPI_CTAR0) 173 # define CONFIG_SYS_DSPI_CTAR2 (CONFIG_SYS_DSPI_CTAR0) 174 #endif 175 176 /* Input, PCI, Flexbus, and VCO */ 177 #define CONFIG_EXTRA_CLOCK 178 179 #define CONFIG_PRAM 2048 /* 2048 KB */ 180 181 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 182 183 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 184 /* Boot Argument Buffer Size */ 185 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 186 187 #define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x10000) 188 189 #define CONFIG_SYS_MBAR 0xFC000000 190 191 /* 192 * Low Level Configuration Settings 193 * (address mappings, register initial values, etc.) 194 * You should know what you are doing if you make changes here. 195 */ 196 197 /*----------------------------------------------------------------------- 198 * Definitions for initial stack pointer and data area (in DPRAM) 199 */ 200 #define CONFIG_SYS_INIT_RAM_ADDR 0x80000000 201 /* End of used area in internal SRAM */ 202 #define CONFIG_SYS_INIT_RAM_SIZE 0x10000 203 #define CONFIG_SYS_INIT_RAM_CTRL 0x221 204 #define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - \ 205 GENERATED_GBL_DATA_SIZE) - 32) 206 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 207 #define CONFIG_SYS_SBFHDR_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - 32) 208 209 /*----------------------------------------------------------------------- 210 * Start addresses for the final memory configuration 211 * (Set up by the startup code) 212 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 213 */ 214 #define CONFIG_SYS_SDRAM_BASE 0x40000000 215 #define CONFIG_SYS_SDRAM_SIZE 128 /* SDRAM size in MB */ 216 217 #define CONFIG_SYS_MEMTEST_START (CONFIG_SYS_SDRAM_BASE + 0x400) 218 #define CONFIG_SYS_MEMTEST_END ((CONFIG_SYS_SDRAM_SIZE - 3) << 20) 219 #define CONFIG_SYS_DRAM_TEST 220 221 #if defined(CONFIG_CF_SBF) || defined(CONFIG_SYS_NAND_BOOT) 222 #define CONFIG_SERIAL_BOOT 223 #endif 224 225 #if defined(CONFIG_SERIAL_BOOT) 226 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_TEXT_BASE + 0x400) 227 #else 228 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) 229 #endif 230 231 #define CONFIG_SYS_BOOTPARAMS_LEN (64 * 1024) 232 /* Reserve 256 kB for Monitor */ 233 #define CONFIG_SYS_MONITOR_LEN (256 << 10) 234 /* Reserve 256 kB for malloc() */ 235 #define CONFIG_SYS_MALLOC_LEN (256 << 10) 236 237 /* 238 * For booting Linux, the board info and command line data 239 * have to be in the first 8 MB of memory, since this is 240 * the maximum mapped by the Linux kernel during initialization ?? 241 */ 242 /* Initial Memory map for Linux */ 243 #define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + \ 244 (CONFIG_SYS_SDRAM_SIZE << 20)) 245 246 /* Configuration for environment 247 * Environment is embedded in u-boot in the second sector of the flash 248 */ 249 #if !defined(CONFIG_SERIAL_BOOT) /*MRAM boot*/ 250 #define CONFIG_ENV_ADDR (0x40000 - 0x1000) /*MRAM size 40000*/ 251 #define CONFIG_ENV_SIZE 0x1000 252 #endif 253 254 #if defined(CONFIG_CF_SBF) 255 #define CONFIG_ENV_SPI_CS 1 256 #define CONFIG_ENV_OFFSET 0x40000 257 #define CONFIG_ENV_SIZE 0x2000 258 #define CONFIG_ENV_SECT_SIZE 0x10000 259 #endif 260 #if defined(CONFIG_SYS_NAND_BOOT) 261 #define CONFIG_ENV_OFFSET 0x80000 262 #define CONFIG_ENV_SIZE 0x20000 263 #define CONFIG_ENV_SECT_SIZE 0x20000 264 #endif 265 #undef CONFIG_ENV_OVERWRITE 266 267 /* FLASH organization */ 268 #define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE 269 270 #undef CONFIG_SYS_FLASH_CFI 271 #ifdef CONFIG_SYS_FLASH_CFI 272 273 #define CONFIG_FLASH_CFI_DRIVER 1 274 /* Max size that the board might have */ 275 #define CONFIG_SYS_FLASH_SIZE 0x1000000 276 #define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT 277 /* max number of memory banks */ 278 #define CONFIG_SYS_MAX_FLASH_BANKS 1 279 /* max number of sectors on one chip */ 280 #define CONFIG_SYS_MAX_FLASH_SECT 270 281 /* "Real" (hardware) sectors protection */ 282 #define CONFIG_SYS_FLASH_PROTECTION 283 #define CONFIG_SYS_FLASH_CHECKSUM 284 #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_CS0_BASE } 285 #else 286 /* max number of sectors on one chip */ 287 #define CONFIG_SYS_MAX_FLASH_SECT 270 288 /* max number of sectors on one chip */ 289 #define CONFIG_SYS_MAX_FLASH_BANKS 0 290 #endif 291 292 /* 293 * This is setting for JFFS2 support in u-boot. 294 * NOTE: Enable CONFIG_CMD_JFFS2 for JFFS2 support. 295 */ 296 #ifdef CONFIG_CMD_JFFS2 297 #define CONFIG_JFFS2_DEV "nand0" 298 #define CONFIG_JFFS2_PART_OFFSET (0x800000) 299 #define CONFIG_MTD_DEVICE 300 #define MTDIDS_DEFAULT "nand0=m54418twr.nand" 301 302 #define MTDPARTS_DEFAULT "mtdparts=m54418twr.nand:1m(data)," \ 303 "7m(kernel)," \ 304 "-(rootfs)" 305 306 #endif 307 308 #ifdef CONFIG_CMD_UBI 309 #define CONFIG_MTD_DEVICE /* needed for mtdparts command */ 310 #define CONFIG_MTD_PARTITIONS /* mtdparts and UBI support */ 311 #define MTDIDS_DEFAULT "nand0=NAND" 312 #define MTDPARTS_DEFAULT "mtdparts=NAND:1m(u-boot)," \ 313 "-(ubi)" 314 #endif 315 /* Cache Configuration */ 316 #define CONFIG_SYS_CACHELINE_SIZE 16 317 #define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 318 CONFIG_SYS_INIT_RAM_SIZE - 8) 319 #define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 320 CONFIG_SYS_INIT_RAM_SIZE - 4) 321 #define CONFIG_SYS_ICACHE_INV (CF_CACR_BCINVA + CF_CACR_ICINVA) 322 #define CONFIG_SYS_DCACHE_INV (CF_CACR_DCINVA) 323 #define CONFIG_SYS_CACHE_ACR2 (CONFIG_SYS_SDRAM_BASE | \ 324 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ 325 CF_ACR_EN | CF_ACR_SM_ALL) 326 #define CONFIG_SYS_CACHE_ICACR (CF_CACR_BEC | CF_CACR_IEC | \ 327 CF_CACR_ICINVA | CF_CACR_EUSP) 328 #define CONFIG_SYS_CACHE_DCACR ((CONFIG_SYS_CACHE_ICACR | \ 329 CF_CACR_DEC | CF_CACR_DDCM_P | \ 330 CF_CACR_DCINVA) & ~CF_CACR_ICINVA) 331 332 #define CACR_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 333 CONFIG_SYS_INIT_RAM_SIZE - 12) 334 335 /*----------------------------------------------------------------------- 336 * Memory bank definitions 337 */ 338 /* 339 * CS0 - NOR Flash 16MB 340 * CS1 - Available 341 * CS2 - Available 342 * CS3 - Available 343 * CS4 - Available 344 * CS5 - Available 345 */ 346 347 /* Flash */ 348 #define CONFIG_SYS_CS0_BASE 0x00000000 349 #define CONFIG_SYS_CS0_MASK 0x000F0101 350 #define CONFIG_SYS_CS0_CTRL 0x00001D60 351 352 #endif /* _M54418TWR_H */ 353