1 /* 2 * Configuation settings for the Freescale MCF5329 FireEngine board. 3 * 4 * Copyright (C) 2004-2007 Freescale Semiconductor, Inc. 5 * TsiChung Liew (Tsi-Chung.Liew@freescale.com) 6 * 7 * SPDX-License-Identifier: GPL-2.0+ 8 */ 9 10 /* 11 * board/config.h - configuration options, board specific 12 */ 13 14 #ifndef _M5329EVB_H 15 #define _M5329EVB_H 16 17 /* 18 * High Level Configuration Options 19 * (easy to change) 20 */ 21 22 #define CONFIG_MCFUART 23 #define CONFIG_SYS_UART_PORT (0) 24 #define CONFIG_BAUDRATE 115200 25 26 #undef CONFIG_WATCHDOG 27 #define CONFIG_WATCHDOG_TIMEOUT 5000 /* timeout in milliseconds, max timeout is 6.71sec */ 28 29 /* Command line configuration */ 30 #define CONFIG_CMD_DATE 31 #define CONFIG_CMD_REGINFO 32 33 #ifdef CONFIG_NANDFLASH_SIZE 34 # define CONFIG_CMD_NAND 35 #endif 36 37 #define CONFIG_SYS_UNIFY_CACHE 38 39 #define CONFIG_MCFFEC 40 #ifdef CONFIG_MCFFEC 41 # define CONFIG_MII 1 42 # define CONFIG_MII_INIT 1 43 # define CONFIG_SYS_DISCOVER_PHY 44 # define CONFIG_SYS_RX_ETH_BUFFER 8 45 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 46 47 # define CONFIG_SYS_FEC0_PINMUX 0 48 # define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE 49 # define MCFFEC_TOUT_LOOP 50000 50 /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */ 51 # ifndef CONFIG_SYS_DISCOVER_PHY 52 # define FECDUPLEX FULL 53 # define FECSPEED _100BASET 54 # else 55 # ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN 56 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 57 # endif 58 # endif /* CONFIG_SYS_DISCOVER_PHY */ 59 #endif 60 61 #define CONFIG_MCFRTC 62 #undef RTC_DEBUG 63 64 /* Timer */ 65 #define CONFIG_MCFTMR 66 #undef CONFIG_MCFPIT 67 68 /* I2C */ 69 #define CONFIG_SYS_I2C 70 #define CONFIG_SYS_I2C_FSL 71 #define CONFIG_SYS_FSL_I2C_SPEED 80000 72 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 73 #define CONFIG_SYS_FSL_I2C_OFFSET 0x58000 74 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR 75 76 #define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */ 77 #define CONFIG_UDP_CHECKSUM 78 79 #ifdef CONFIG_MCFFEC 80 # define CONFIG_IPADDR 192.162.1.2 81 # define CONFIG_NETMASK 255.255.255.0 82 # define CONFIG_SERVERIP 192.162.1.1 83 # define CONFIG_GATEWAYIP 192.162.1.1 84 #endif /* FEC_ENET */ 85 86 #define CONFIG_HOSTNAME M5329EVB 87 #define CONFIG_EXTRA_ENV_SETTINGS \ 88 "netdev=eth0\0" \ 89 "loadaddr=40010000\0" \ 90 "u-boot=u-boot.bin\0" \ 91 "load=tftp ${loadaddr) ${u-boot}\0" \ 92 "upd=run load; run prog\0" \ 93 "prog=prot off 0 3ffff;" \ 94 "era 0 3ffff;" \ 95 "cp.b ${loadaddr} 0 ${filesize};" \ 96 "save\0" \ 97 "" 98 99 #define CONFIG_PRAM 512 /* 512 KB */ 100 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 101 102 #ifdef CONFIG_CMD_KGDB 103 # define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 104 #else 105 # define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 106 #endif 107 108 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 109 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 110 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 111 #define CONFIG_SYS_LOAD_ADDR 0x40010000 112 113 #define CONFIG_SYS_CLK 80000000 114 #define CONFIG_SYS_CPU_CLK CONFIG_SYS_CLK * 3 115 116 #define CONFIG_SYS_MBAR 0xFC000000 117 118 #define CONFIG_SYS_LATCH_ADDR (CONFIG_SYS_CS1_BASE + 0x80000) 119 120 /* 121 * Low Level Configuration Settings 122 * (address mappings, register initial values, etc.) 123 * You should know what you are doing if you make changes here. 124 */ 125 /*----------------------------------------------------------------------- 126 * Definitions for initial stack pointer and data area (in DPRAM) 127 */ 128 #define CONFIG_SYS_INIT_RAM_ADDR 0x80000000 129 #define CONFIG_SYS_INIT_RAM_SIZE 0x8000 /* Size of used area in internal SRAM */ 130 #define CONFIG_SYS_INIT_RAM_CTRL 0x221 131 #define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - 0x10) 132 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 133 134 /*----------------------------------------------------------------------- 135 * Start addresses for the final memory configuration 136 * (Set up by the startup code) 137 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 138 */ 139 #define CONFIG_SYS_SDRAM_BASE 0x40000000 140 #define CONFIG_SYS_SDRAM_SIZE 32 /* SDRAM size in MB */ 141 #define CONFIG_SYS_SDRAM_CFG1 0x53722730 142 #define CONFIG_SYS_SDRAM_CFG2 0x56670000 143 #define CONFIG_SYS_SDRAM_CTRL 0xE1092000 144 #define CONFIG_SYS_SDRAM_EMOD 0x40010000 145 #define CONFIG_SYS_SDRAM_MODE 0x018D0000 146 147 #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE + 0x400 148 #define CONFIG_SYS_MEMTEST_END ((CONFIG_SYS_SDRAM_SIZE - 3) << 20) 149 150 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) 151 #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ 152 153 #define CONFIG_SYS_BOOTPARAMS_LEN 64*1024 154 #define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ 155 156 /* 157 * For booting Linux, the board info and command line data 158 * have to be in the first 8 MB of memory, since this is 159 * the maximum mapped by the Linux kernel during initialization ?? 160 */ 161 #define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20)) 162 #define CONFIG_SYS_BOOTM_LEN (CONFIG_SYS_SDRAM_SIZE << 20) 163 164 /*----------------------------------------------------------------------- 165 * FLASH organization 166 */ 167 #define CONFIG_SYS_FLASH_CFI 168 #ifdef CONFIG_SYS_FLASH_CFI 169 # define CONFIG_FLASH_CFI_DRIVER 1 170 # define CONFIG_SYS_FLASH_SIZE 0x800000 /* Max size that the board might have */ 171 # define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT 172 # define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ 173 # define CONFIG_SYS_MAX_FLASH_SECT 137 /* max number of sectors on one chip */ 174 # define CONFIG_SYS_FLASH_PROTECTION /* "Real" (hardware) sectors protection */ 175 #endif 176 177 #ifdef CONFIG_NANDFLASH_SIZE 178 # define CONFIG_SYS_MAX_NAND_DEVICE 1 179 # define CONFIG_SYS_NAND_BASE CONFIG_SYS_CS2_BASE 180 # define CONFIG_SYS_NAND_SIZE 1 181 # define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } 182 # define NAND_ALLOW_ERASE_ALL 1 183 # define CONFIG_JFFS2_NAND 1 184 # define CONFIG_JFFS2_DEV "nand0" 185 # define CONFIG_JFFS2_PART_SIZE (CONFIG_SYS_CS2_MASK & ~1) 186 # define CONFIG_JFFS2_PART_OFFSET 0x00000000 187 #endif 188 189 #define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE 190 191 /* Configuration for environment 192 * Environment is embedded in u-boot in the second sector of the flash 193 */ 194 #define CONFIG_ENV_OFFSET 0x4000 195 #define CONFIG_ENV_SECT_SIZE 0x2000 196 #define CONFIG_ENV_IS_IN_FLASH 1 197 198 #define LDS_BOARD_TEXT \ 199 . = DEFINED(env_offset) ? env_offset : .; \ 200 common/env_embedded.o (.text*); 201 202 /*----------------------------------------------------------------------- 203 * Cache Configuration 204 */ 205 #define CONFIG_SYS_CACHELINE_SIZE 16 206 207 #define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 208 CONFIG_SYS_INIT_RAM_SIZE - 8) 209 #define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 210 CONFIG_SYS_INIT_RAM_SIZE - 4) 211 #define CONFIG_SYS_ICACHE_INV (CF_CACR_CINVA) 212 #define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ 213 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ 214 CF_ACR_EN | CF_ACR_SM_ALL) 215 #define CONFIG_SYS_CACHE_ICACR (CF_CACR_EC | CF_CACR_CINVA | \ 216 CF_CACR_DCM_P) 217 218 /*----------------------------------------------------------------------- 219 * Chipselect bank definitions 220 */ 221 /* 222 * CS0 - NOR Flash 1, 2, 4, or 8MB 223 * CS1 - CompactFlash and registers 224 * CS2 - NAND Flash 16, 32, or 64MB 225 * CS3 - Available 226 * CS4 - Available 227 * CS5 - Available 228 */ 229 #define CONFIG_SYS_CS0_BASE 0 230 #define CONFIG_SYS_CS0_MASK 0x007f0001 231 #define CONFIG_SYS_CS0_CTRL 0x00001fa0 232 233 #define CONFIG_SYS_CS1_BASE 0x10000000 234 #define CONFIG_SYS_CS1_MASK 0x001f0001 235 #define CONFIG_SYS_CS1_CTRL 0x002A3780 236 237 #ifdef CONFIG_NANDFLASH_SIZE 238 #define CONFIG_SYS_CS2_BASE 0x20000000 239 #define CONFIG_SYS_CS2_MASK ((CONFIG_NANDFLASH_SIZE << 20) | 1) 240 #define CONFIG_SYS_CS2_CTRL 0x00001f60 241 #endif 242 243 #endif /* _M5329EVB_H */ 244