1 /* 2 * Configuation settings for the Motorola MC5282EVB board. 3 * 4 * (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de> 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 /* 10 * board/config.h - configuration options, board specific 11 */ 12 13 #ifndef _CONFIG_M5282EVB_H 14 #define _CONFIG_M5282EVB_H 15 16 /* 17 * High Level Configuration Options 18 * (easy to change) 19 */ 20 #define CONFIG_MCFTMR 21 22 #define CONFIG_MCFUART 23 #define CONFIG_SYS_UART_PORT (0) 24 25 #undef CONFIG_MONITOR_IS_IN_RAM /* define if monitor is started from a pre-loader */ 26 27 /* Configuration for environment 28 * Environment is embedded in u-boot in the second sector of the flash 29 */ 30 #define CONFIG_ENV_ADDR 0xffe04000 31 #define CONFIG_ENV_SIZE 0x2000 32 33 #define LDS_BOARD_TEXT \ 34 . = DEFINED(env_offset) ? env_offset : .; \ 35 common/env_embedded.o (.text*); 36 37 /* 38 * BOOTP options 39 */ 40 #define CONFIG_BOOTP_BOOTFILESIZE 41 #define CONFIG_BOOTP_BOOTPATH 42 #define CONFIG_BOOTP_GATEWAY 43 #define CONFIG_BOOTP_HOSTNAME 44 45 /* 46 * Command line configuration. 47 */ 48 49 #define CONFIG_MCFFEC 50 #ifdef CONFIG_MCFFEC 51 # define CONFIG_MII 1 52 # define CONFIG_MII_INIT 1 53 # define CONFIG_SYS_DISCOVER_PHY 54 # define CONFIG_SYS_RX_ETH_BUFFER 8 55 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 56 57 # define CONFIG_SYS_FEC0_PINMUX 0 58 # define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE 59 # define MCFFEC_TOUT_LOOP 50000 60 /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */ 61 # ifndef CONFIG_SYS_DISCOVER_PHY 62 # define FECDUPLEX FULL 63 # define FECSPEED _100BASET 64 # else 65 # ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN 66 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 67 # endif 68 # endif /* CONFIG_SYS_DISCOVER_PHY */ 69 #endif 70 71 #ifdef CONFIG_MCFFEC 72 # define CONFIG_IPADDR 192.162.1.2 73 # define CONFIG_NETMASK 255.255.255.0 74 # define CONFIG_SERVERIP 192.162.1.1 75 # define CONFIG_GATEWAYIP 192.162.1.1 76 #endif /* CONFIG_MCFFEC */ 77 78 #define CONFIG_HOSTNAME M5282EVB 79 #define CONFIG_EXTRA_ENV_SETTINGS \ 80 "netdev=eth0\0" \ 81 "loadaddr=10000\0" \ 82 "u-boot=u-boot.bin\0" \ 83 "load=tftp ${loadaddr) ${u-boot}\0" \ 84 "upd=run load; run prog\0" \ 85 "prog=prot off ffe00000 ffe3ffff;" \ 86 "era ffe00000 ffe3ffff;" \ 87 "cp.b ${loadaddr} ffe00000 ${filesize};"\ 88 "save\0" \ 89 "" 90 91 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 92 93 #if defined(CONFIG_CMD_KGDB) 94 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 95 #else 96 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 97 #endif 98 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 99 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 100 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 101 102 #define CONFIG_SYS_LOAD_ADDR 0x20000 103 104 #define CONFIG_SYS_MEMTEST_START 0x400 105 #define CONFIG_SYS_MEMTEST_END 0x380000 106 107 #define CONFIG_SYS_CLK 64000000 108 109 /* PLL Configuration: Ext Clock * 6 (see table 9-4 of MCF user manual) */ 110 111 #define CONFIG_SYS_MFD 0x02 /* PLL Multiplication Factor Devider */ 112 #define CONFIG_SYS_RFD 0x00 /* PLL Reduce Frecuency Devider */ 113 114 /* 115 * Low Level Configuration Settings 116 * (address mappings, register initial values, etc.) 117 * You should know what you are doing if you make changes here. 118 */ 119 #define CONFIG_SYS_MBAR 0x40000000 120 121 /*----------------------------------------------------------------------- 122 * Definitions for initial stack pointer and data area (in DPRAM) 123 */ 124 #define CONFIG_SYS_INIT_RAM_ADDR 0x20000000 125 #define CONFIG_SYS_INIT_RAM_SIZE 0x10000 /* Size of used area in internal SRAM */ 126 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 127 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 128 129 /*----------------------------------------------------------------------- 130 * Start addresses for the final memory configuration 131 * (Set up by the startup code) 132 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 133 */ 134 #define CONFIG_SYS_SDRAM_BASE 0x00000000 135 #define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */ 136 #define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE 137 #define CONFIG_SYS_INT_FLASH_BASE 0xf0000000 138 #define CONFIG_SYS_INT_FLASH_ENABLE 0x21 139 140 /* If M5282 port is fully implemented the monitor base will be behind 141 * the vector table. */ 142 #if (CONFIG_SYS_TEXT_BASE != CONFIG_SYS_INT_FLASH_BASE) 143 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) 144 #else 145 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_TEXT_BASE + 0x418) /* 24 Byte for CFM-Config */ 146 #endif 147 148 #define CONFIG_SYS_MONITOR_LEN 0x20000 149 #define CONFIG_SYS_MALLOC_LEN (256 << 10) 150 #define CONFIG_SYS_BOOTPARAMS_LEN 64*1024 151 152 /* 153 * For booting Linux, the board info and command line data 154 * have to be in the first 8 MB of memory, since this is 155 * the maximum mapped by the Linux kernel during initialization ?? 156 */ 157 #define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20)) 158 159 /*----------------------------------------------------------------------- 160 * FLASH organization 161 */ 162 #define CONFIG_SYS_FLASH_CFI 163 #ifdef CONFIG_SYS_FLASH_CFI 164 165 # define CONFIG_FLASH_CFI_DRIVER 1 166 # define CONFIG_SYS_FLASH_SIZE 0x1000000 /* Max size that the board might have */ 167 # define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT 168 # define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ 169 # define CONFIG_SYS_MAX_FLASH_SECT 137 /* max number of sectors on one chip */ 170 # define CONFIG_SYS_FLASH_PROTECTION /* "Real" (hardware) sectors protection */ 171 # define CONFIG_SYS_FLASH_CHECKSUM 172 # define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } 173 #endif 174 175 /*----------------------------------------------------------------------- 176 * Cache Configuration 177 */ 178 #define CONFIG_SYS_CACHELINE_SIZE 16 179 180 #define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 181 CONFIG_SYS_INIT_RAM_SIZE - 8) 182 #define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 183 CONFIG_SYS_INIT_RAM_SIZE - 4) 184 #define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV + CF_CACR_DCM) 185 #define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ 186 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ 187 CF_ACR_EN | CF_ACR_SM_ALL) 188 #define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_DISD | \ 189 CF_CACR_CEIB | CF_CACR_DBWE | \ 190 CF_CACR_EUSP) 191 192 /*----------------------------------------------------------------------- 193 * Memory bank definitions 194 */ 195 #define CONFIG_SYS_CS0_BASE 0xFFE00000 196 #define CONFIG_SYS_CS0_CTRL 0x00001980 197 #define CONFIG_SYS_CS0_MASK 0x001F0001 198 199 /*----------------------------------------------------------------------- 200 * Port configuration 201 */ 202 #define CONFIG_SYS_PACNT 0x0000000 /* Port A D[31:24] */ 203 #define CONFIG_SYS_PADDR 0x0000000 204 #define CONFIG_SYS_PADAT 0x0000000 205 206 #define CONFIG_SYS_PBCNT 0x0000000 /* Port B D[23:16] */ 207 #define CONFIG_SYS_PBDDR 0x0000000 208 #define CONFIG_SYS_PBDAT 0x0000000 209 210 #define CONFIG_SYS_PCCNT 0x0000000 /* Port C D[15:08] */ 211 #define CONFIG_SYS_PCDDR 0x0000000 212 #define CONFIG_SYS_PCDAT 0x0000000 213 214 #define CONFIG_SYS_PDCNT 0x0000000 /* Port D D[07:00] */ 215 #define CONFIG_SYS_PCDDR 0x0000000 216 #define CONFIG_SYS_PCDAT 0x0000000 217 218 #define CONFIG_SYS_PEHLPAR 0xC0 219 #define CONFIG_SYS_PUAPAR 0x0F /* UA0..UA3 = Uart 0 +1 */ 220 #define CONFIG_SYS_DDRUA 0x05 221 #define CONFIG_SYS_PJPAR 0xFF 222 223 #endif /* _CONFIG_M5282EVB_H */ 224