1 /* 2 * Copyright (C) 2004-2007 Freescale Semiconductor, Inc. 3 * Hayden Fraser (Hayden.Fraser@freescale.com) 4 * 5 * See file CREDITS for list of people who contributed to this 6 * project. 7 * 8 * This program is free software; you can redistribute it and/or 9 * modify it under the terms of the GNU General Public License as 10 * published by the Free Software Foundation; either version 2 of 11 * the License, or (at your option) any later version. 12 * 13 * This program is distributed in the hope that it will be useful, 14 * but WITHOUT ANY WARRANTY; without even the implied warranty of 15 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 16 * GNU General Public License for more details. 17 * 18 * You should have received a copy of the GNU General Public License 19 * along with this program; if not, write to the Free Software 20 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 21 * MA 02111-1307 USA 22 */ 23 24 #ifndef _M5253DEMO_H 25 #define _M5253DEMO_H 26 27 #define CONFIG_MCF52x2 /* define processor family */ 28 #define CONFIG_M5253 /* define processor type */ 29 #define CONFIG_M5253DEMO /* define board type */ 30 31 #define CONFIG_MCFTMR 32 33 #define CONFIG_MCFUART 34 #define CONFIG_SYS_UART_PORT (0) 35 #define CONFIG_BAUDRATE 115200 36 #define CONFIG_SYS_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } 37 38 #undef CONFIG_WATCHDOG /* disable watchdog */ 39 40 #define CONFIG_BOOTDELAY 5 41 42 /* Configuration for environment 43 * Environment is embedded in u-boot in the second sector of the flash 44 */ 45 #ifdef CONFIG_MONITOR_IS_IN_RAM 46 # define CONFIG_ENV_OFFSET 0x4000 47 # define CONFIG_ENV_SECT_SIZE 0x1000 48 # define CONFIG_ENV_IS_IN_FLASH 1 49 #else 50 # define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x4000) 51 # define CONFIG_ENV_SECT_SIZE 0x1000 52 # define CONFIG_ENV_IS_IN_FLASH 1 53 #endif 54 55 /* 56 * Command line configuration. 57 */ 58 #include <config_cmd_default.h> 59 60 #define CONFIG_CMD_CACHE 61 #define CONFIG_CMD_LOADB 62 #define CONFIG_CMD_LOADS 63 #define CONFIG_CMD_EXT2 64 #define CONFIG_CMD_FAT 65 #define CONFIG_CMD_IDE 66 #define CONFIG_CMD_MEMORY 67 #define CONFIG_CMD_MISC 68 #define CONFIG_CMD_PING 69 70 #ifdef CONFIG_CMD_IDE 71 /* ATA */ 72 # define CONFIG_DOS_PARTITION 73 # define CONFIG_MAC_PARTITION 74 # define CONFIG_IDE_RESET 1 75 # define CONFIG_IDE_PREINIT 1 76 # define CONFIG_ATAPI 77 # undef CONFIG_LBA48 78 79 # define CONFIG_SYS_IDE_MAXBUS 1 80 # define CONFIG_SYS_IDE_MAXDEVICE 2 81 82 # define CONFIG_SYS_ATA_BASE_ADDR (CONFIG_SYS_MBAR2 + 0x800) 83 # define CONFIG_SYS_ATA_IDE0_OFFSET 0 84 85 # define CONFIG_SYS_ATA_DATA_OFFSET 0xA0 /* Offset for data I/O */ 86 # define CONFIG_SYS_ATA_REG_OFFSET 0xA0 /* Offset for normal register accesses */ 87 # define CONFIG_SYS_ATA_ALT_OFFSET 0xC0 /* Offset for alternate registers */ 88 # define CONFIG_SYS_ATA_STRIDE 4 /* Interval between registers */ 89 #endif 90 91 #define CONFIG_NET_MULTI 1 92 #define CONFIG_DRIVER_DM9000 93 #ifdef CONFIG_DRIVER_DM9000 94 # define CONFIG_DM9000_BASE (CONFIG_SYS_CS1_BASE | 0x300) 95 # define DM9000_IO CONFIG_DM9000_BASE 96 # define DM9000_DATA (CONFIG_DM9000_BASE + 4) 97 # undef CONFIG_DM9000_DEBUG 98 99 # define CONFIG_OVERWRITE_ETHADDR_ONCE 100 101 # define CONFIG_EXTRA_ENV_SETTINGS \ 102 "netdev=eth0\0" \ 103 "inpclk=" MK_STR(CONFIG_SYS_INPUT_CLKSRC) "\0" \ 104 "loadaddr=10000\0" \ 105 "u-boot=u-boot.bin\0" \ 106 "load=tftp ${loadaddr) ${u-boot}\0" \ 107 "upd=run load; run prog\0" \ 108 "prog=prot off 0xff800000 0xff82ffff;" \ 109 "era 0xff800000 0xff82ffff;" \ 110 "cp.b ${loadaddr} 0xff800000 ${filesize};" \ 111 "save\0" \ 112 "" 113 #endif 114 115 #define CONFIG_HOSTNAME M5253DEMO 116 117 /* I2C */ 118 #define CONFIG_FSL_I2C 119 #define CONFIG_HARD_I2C /* I2C with hw support */ 120 #define CONFIG_SYS_I2C_SPEED 80000 121 #define CONFIG_SYS_I2C_SLAVE 0x7F 122 #define CONFIG_SYS_I2C_OFFSET 0x00000280 123 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR 124 #define CONFIG_SYS_I2C_PINMUX_REG (*(u32 *) (CONFIG_SYS_MBAR+0x19C)) 125 #define CONFIG_SYS_I2C_PINMUX_CLR (0xFFFFE7FF) 126 #define CONFIG_SYS_I2C_PINMUX_SET (0) 127 128 #define CONFIG_SYS_PROMPT "=> " 129 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 130 131 #if defined(CONFIG_CMD_KGDB) 132 # define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 133 #else 134 # define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 135 #endif 136 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 137 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 138 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 139 140 #define CONFIG_SYS_LOAD_ADDR 0x00100000 141 142 #define CONFIG_SYS_MEMTEST_START 0x400 143 #define CONFIG_SYS_MEMTEST_END 0x380000 144 145 #define CONFIG_SYS_HZ 1000 146 147 #undef CONFIG_SYS_PLL_BYPASS /* bypass PLL for test purpose */ 148 #define CONFIG_SYS_FAST_CLK 149 #ifdef CONFIG_SYS_FAST_CLK 150 # define CONFIG_SYS_PLLCR 0x1243E054 151 # define CONFIG_SYS_CLK 140000000 152 #else 153 # define CONFIG_SYS_PLLCR 0x135a4140 154 # define CONFIG_SYS_CLK 70000000 155 #endif 156 157 /* 158 * Low Level Configuration Settings 159 * (address mappings, register initial values, etc.) 160 * You should know what you are doing if you make changes here. 161 */ 162 163 #define CONFIG_SYS_MBAR 0x10000000 /* Register Base Addrs */ 164 #define CONFIG_SYS_MBAR2 0x80000000 /* Module Base Addrs 2 */ 165 166 /* 167 * Definitions for initial stack pointer and data area (in DPRAM) 168 */ 169 #define CONFIG_SYS_INIT_RAM_ADDR 0x20000000 170 #define CONFIG_SYS_INIT_RAM_END 0x10000 /* End of used area in internal SRAM */ 171 #define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ 172 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) 173 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 174 175 /* 176 * Start addresses for the final memory configuration 177 * (Set up by the startup code) 178 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 179 */ 180 #define CONFIG_SYS_SDRAM_BASE 0x00000000 181 #define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */ 182 183 #ifdef CONFIG_MONITOR_IS_IN_RAM 184 # define CONFIG_SYS_MONITOR_BASE 0x20000 185 #else 186 # define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) 187 #endif 188 189 #define CONFIG_SYS_MONITOR_LEN 0x40000 190 #define CONFIG_SYS_MALLOC_LEN (256 << 10) 191 #define CONFIG_SYS_BOOTPARAMS_LEN (64*1024) 192 193 /* 194 * For booting Linux, the board info and command line data 195 * have to be in the first 8 MB of memory, since this is 196 * the maximum mapped by the Linux kernel during initialization ?? 197 */ 198 #define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20)) 199 #define CONFIG_SYS_BOOTM_LEN (CONFIG_SYS_SDRAM_SIZE << 20) 200 201 /* FLASH organization */ 202 #define CONFIG_SYS_FLASH_BASE (CONFIG_SYS_CS0_BASE) 203 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ 204 #define CONFIG_SYS_MAX_FLASH_SECT 2048 /* max number of sectors on one chip */ 205 #define CONFIG_SYS_FLASH_ERASE_TOUT 1000 206 207 #define FLASH_SST6401B 0x200 208 #define SST_ID_xF6401B 0x236D236D 209 210 #undef CONFIG_SYS_FLASH_CFI 211 #ifdef CONFIG_SYS_FLASH_CFI 212 /* 213 * Unable to use CFI driver, due to incompatible sector erase command by SST. 214 * Amd/Atmel use 0x30 for sector erase, SST use 0x50. 215 * 0x30 is block erase in SST 216 */ 217 # define CONFIG_FLASH_CFI_DRIVER 1 218 # define CONFIG_SYS_FLASH_SIZE 0x800000 219 # define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT 220 # define CONFIG_FLASH_CFI_LEGACY 221 #else 222 # define CONFIG_SYS_SST_SECT 2048 223 # define CONFIG_SYS_SST_SECTSZ 0x1000 224 # define CONFIG_SYS_FLASH_WRITE_TOUT 500 225 #endif 226 227 /* Cache Configuration */ 228 #define CONFIG_SYS_CACHELINE_SIZE 16 229 230 #define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 231 CONFIG_SYS_INIT_RAM_END - 8) 232 #define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 233 CONFIG_SYS_INIT_RAM_END - 4) 234 #define CONFIG_SYS_ICACHE_INV (CF_CACR_DCM) 235 #define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_FLASH_BASE | \ 236 CF_ADDRMASK(8) | \ 237 CF_ACR_EN | CF_ACR_SM_ALL) 238 #define CONFIG_SYS_CACHE_ACR1 (CONFIG_SYS_SDRAM_BASE | \ 239 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ 240 CF_ACR_EN | CF_ACR_SM_ALL) 241 #define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CEIB | \ 242 CF_CACR_DBWE) 243 244 /* Port configuration */ 245 #define CONFIG_SYS_FECI2C 0xF0 246 247 #define CONFIG_SYS_CS0_BASE 0xFF800000 248 #define CONFIG_SYS_CS0_MASK 0x007F0021 249 #define CONFIG_SYS_CS0_CTRL 0x00001D80 250 251 #define CONFIG_SYS_CS1_BASE 0xE0000000 252 #define CONFIG_SYS_CS1_MASK 0x00000001 253 #define CONFIG_SYS_CS1_CTRL 0x00003DD8 254 255 /*----------------------------------------------------------------------- 256 * Port configuration 257 */ 258 #define CONFIG_SYS_GPIO_FUNC 0x00000008 /* Set gpio pins: none */ 259 #define CONFIG_SYS_GPIO1_FUNC 0x00df00f0 /* 36-39(SWITCH),48-52(FPGAs),54 */ 260 #define CONFIG_SYS_GPIO_EN 0x00000008 /* Set gpio output enable */ 261 #define CONFIG_SYS_GPIO1_EN 0x00c70000 /* Set gpio output enable */ 262 #define CONFIG_SYS_GPIO_OUT 0x00000008 /* Set outputs to default state */ 263 #define CONFIG_SYS_GPIO1_OUT 0x00c70000 /* Set outputs to default state */ 264 #define CONFIG_SYS_GPIO1_LED 0x00400000 /* user led */ 265 266 #endif /* _M5253DEMO_H */ 267