1 /* Copyright (C) 2004-2007 Freescale Semiconductor, Inc. 2 * Hayden Fraser (Hayden.Fraser@freescale.com) 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #ifndef _M5253DEMO_H 8 #define _M5253DEMO_H 9 10 #define CONFIG_M5253DEMO /* define board type */ 11 12 #define CONFIG_MCFTMR 13 14 #define CONFIG_MCFUART 15 #define CONFIG_SYS_UART_PORT (0) 16 17 #undef CONFIG_WATCHDOG /* disable watchdog */ 18 19 20 /* Configuration for environment 21 * Environment is embedded in u-boot in the second sector of the flash 22 */ 23 #ifdef CONFIG_MONITOR_IS_IN_RAM 24 # define CONFIG_ENV_OFFSET 0x4000 25 # define CONFIG_ENV_SECT_SIZE 0x1000 26 #else 27 # define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x4000) 28 # define CONFIG_ENV_SECT_SIZE 0x1000 29 #endif 30 31 #define LDS_BOARD_TEXT \ 32 . = DEFINED(env_offset) ? env_offset : .; \ 33 common/env_embedded.o (.text*); 34 35 /* 36 * Command line configuration. 37 */ 38 39 #ifdef CONFIG_IDE 40 /* ATA */ 41 # define CONFIG_IDE_RESET 1 42 # define CONFIG_IDE_PREINIT 1 43 # define CONFIG_ATAPI 44 # undef CONFIG_LBA48 45 46 # define CONFIG_SYS_IDE_MAXBUS 1 47 # define CONFIG_SYS_IDE_MAXDEVICE 2 48 49 # define CONFIG_SYS_ATA_BASE_ADDR (CONFIG_SYS_MBAR2 + 0x800) 50 # define CONFIG_SYS_ATA_IDE0_OFFSET 0 51 52 # define CONFIG_SYS_ATA_DATA_OFFSET 0xA0 /* Offset for data I/O */ 53 # define CONFIG_SYS_ATA_REG_OFFSET 0xA0 /* Offset for normal register accesses */ 54 # define CONFIG_SYS_ATA_ALT_OFFSET 0xC0 /* Offset for alternate registers */ 55 # define CONFIG_SYS_ATA_STRIDE 4 /* Interval between registers */ 56 #endif 57 58 #define CONFIG_DRIVER_DM9000 59 #ifdef CONFIG_DRIVER_DM9000 60 # define CONFIG_DM9000_BASE (CONFIG_SYS_CS1_BASE | 0x300) 61 # define DM9000_IO CONFIG_DM9000_BASE 62 # define DM9000_DATA (CONFIG_DM9000_BASE + 4) 63 # undef CONFIG_DM9000_DEBUG 64 # define CONFIG_DM9000_BYTE_SWAPPED 65 66 # define CONFIG_OVERWRITE_ETHADDR_ONCE 67 68 # define CONFIG_EXTRA_ENV_SETTINGS \ 69 "netdev=eth0\0" \ 70 "inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0" \ 71 "loadaddr=10000\0" \ 72 "u-boot=u-boot.bin\0" \ 73 "load=tftp ${loadaddr) ${u-boot}\0" \ 74 "upd=run load; run prog\0" \ 75 "prog=prot off 0xff800000 0xff82ffff;" \ 76 "era 0xff800000 0xff82ffff;" \ 77 "cp.b ${loadaddr} 0xff800000 ${filesize};" \ 78 "save\0" \ 79 "" 80 #endif 81 82 #define CONFIG_HOSTNAME M5253DEMO 83 84 /* I2C */ 85 #define CONFIG_SYS_I2C 86 #define CONFIG_SYS_I2C_FSL 87 #define CONFIG_SYS_FSL_I2C_SPEED 80000 88 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 89 #define CONFIG_SYS_FSL_I2C_OFFSET 0x00000280 90 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR 91 #define CONFIG_SYS_I2C_PINMUX_REG (*(u32 *) (CONFIG_SYS_MBAR+0x19C)) 92 #define CONFIG_SYS_I2C_PINMUX_CLR (0xFFFFE7FF) 93 #define CONFIG_SYS_I2C_PINMUX_SET (0) 94 95 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 96 97 #if defined(CONFIG_CMD_KGDB) 98 # define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 99 #else 100 # define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 101 #endif 102 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 103 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 104 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 105 106 #define CONFIG_SYS_LOAD_ADDR 0x00100000 107 108 #define CONFIG_SYS_MEMTEST_START 0x400 109 #define CONFIG_SYS_MEMTEST_END 0x380000 110 111 #undef CONFIG_SYS_PLL_BYPASS /* bypass PLL for test purpose */ 112 #define CONFIG_SYS_FAST_CLK 113 #ifdef CONFIG_SYS_FAST_CLK 114 # define CONFIG_SYS_PLLCR 0x1243E054 115 # define CONFIG_SYS_CLK 140000000 116 #else 117 # define CONFIG_SYS_PLLCR 0x135a4140 118 # define CONFIG_SYS_CLK 70000000 119 #endif 120 121 /* 122 * Low Level Configuration Settings 123 * (address mappings, register initial values, etc.) 124 * You should know what you are doing if you make changes here. 125 */ 126 127 #define CONFIG_SYS_MBAR 0x10000000 /* Register Base Addrs */ 128 #define CONFIG_SYS_MBAR2 0x80000000 /* Module Base Addrs 2 */ 129 130 /* 131 * Definitions for initial stack pointer and data area (in DPRAM) 132 */ 133 #define CONFIG_SYS_INIT_RAM_ADDR 0x20000000 134 #define CONFIG_SYS_INIT_RAM_SIZE 0x10000 /* Size of used area in internal SRAM */ 135 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 136 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 137 138 /* 139 * Start addresses for the final memory configuration 140 * (Set up by the startup code) 141 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 142 */ 143 #define CONFIG_SYS_SDRAM_BASE 0x00000000 144 #define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */ 145 146 #ifdef CONFIG_MONITOR_IS_IN_RAM 147 # define CONFIG_SYS_MONITOR_BASE 0x20000 148 #else 149 # define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) 150 #endif 151 152 #define CONFIG_SYS_MONITOR_LEN 0x40000 153 #define CONFIG_SYS_MALLOC_LEN (256 << 10) 154 #define CONFIG_SYS_BOOTPARAMS_LEN (64*1024) 155 156 /* 157 * For booting Linux, the board info and command line data 158 * have to be in the first 8 MB of memory, since this is 159 * the maximum mapped by the Linux kernel during initialization ?? 160 */ 161 #define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20)) 162 #define CONFIG_SYS_BOOTM_LEN (CONFIG_SYS_SDRAM_SIZE << 20) 163 164 /* FLASH organization */ 165 #define CONFIG_SYS_FLASH_BASE (CONFIG_SYS_CS0_BASE) 166 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ 167 #define CONFIG_SYS_MAX_FLASH_SECT 2048 /* max number of sectors on one chip */ 168 #define CONFIG_SYS_FLASH_ERASE_TOUT 1000 169 170 #define FLASH_SST6401B 0x200 171 #define SST_ID_xF6401B 0x236D236D 172 173 #undef CONFIG_SYS_FLASH_CFI 174 #ifdef CONFIG_SYS_FLASH_CFI 175 /* 176 * Unable to use CFI driver, due to incompatible sector erase command by SST. 177 * Amd/Atmel use 0x30 for sector erase, SST use 0x50. 178 * 0x30 is block erase in SST 179 */ 180 # define CONFIG_FLASH_CFI_DRIVER 1 181 # define CONFIG_SYS_FLASH_SIZE 0x800000 182 # define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT 183 # define CONFIG_FLASH_CFI_LEGACY 184 #else 185 # define CONFIG_SYS_SST_SECT 2048 186 # define CONFIG_SYS_SST_SECTSZ 0x1000 187 # define CONFIG_SYS_FLASH_WRITE_TOUT 500 188 #endif 189 190 /* Cache Configuration */ 191 #define CONFIG_SYS_CACHELINE_SIZE 16 192 193 #define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 194 CONFIG_SYS_INIT_RAM_SIZE - 8) 195 #define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 196 CONFIG_SYS_INIT_RAM_SIZE - 4) 197 #define CONFIG_SYS_ICACHE_INV (CF_CACR_DCM) 198 #define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_FLASH_BASE | \ 199 CF_ADDRMASK(8) | \ 200 CF_ACR_EN | CF_ACR_SM_ALL) 201 #define CONFIG_SYS_CACHE_ACR1 (CONFIG_SYS_SDRAM_BASE | \ 202 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ 203 CF_ACR_EN | CF_ACR_SM_ALL) 204 #define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CEIB | \ 205 CF_CACR_DBWE) 206 207 /* Port configuration */ 208 #define CONFIG_SYS_FECI2C 0xF0 209 210 #define CONFIG_SYS_CS0_BASE 0xFF800000 211 #define CONFIG_SYS_CS0_MASK 0x007F0021 212 #define CONFIG_SYS_CS0_CTRL 0x00001D80 213 214 #define CONFIG_SYS_CS1_BASE 0xE0000000 215 #define CONFIG_SYS_CS1_MASK 0x00000001 216 #define CONFIG_SYS_CS1_CTRL 0x00003DD8 217 218 /*----------------------------------------------------------------------- 219 * Port configuration 220 */ 221 #define CONFIG_SYS_GPIO_FUNC 0x00000008 /* Set gpio pins: none */ 222 #define CONFIG_SYS_GPIO1_FUNC 0x00df00f0 /* 36-39(SWITCH),48-52(FPGAs),54 */ 223 #define CONFIG_SYS_GPIO_EN 0x00000008 /* Set gpio output enable */ 224 #define CONFIG_SYS_GPIO1_EN 0x00c70000 /* Set gpio output enable */ 225 #define CONFIG_SYS_GPIO_OUT 0x00000008 /* Set outputs to default state */ 226 #define CONFIG_SYS_GPIO1_OUT 0x00c70000 /* Set outputs to default state */ 227 #define CONFIG_SYS_GPIO1_LED 0x00400000 /* user led */ 228 229 #endif /* _M5253DEMO_H */ 230