1 /* 2 * Configuation settings for the Freescale MCF5208EVBe. 3 * 4 * Copyright (C) 2004-2008 Freescale Semiconductor, Inc. 5 * TsiChung Liew (Tsi-Chung.Liew@freescale.com) 6 * 7 * SPDX-License-Identifier: GPL-2.0+ 8 */ 9 10 #ifndef _M5208EVBE_H 11 #define _M5208EVBE_H 12 13 /* 14 * High Level Configuration Options 15 * (easy to change) 16 */ 17 #define CONFIG_MCF520x /* define processor family */ 18 #define CONFIG_M5208 /* define processor type */ 19 20 #define CONFIG_MCFUART 21 #define CONFIG_SYS_UART_PORT (0) 22 #define CONFIG_BAUDRATE 115200 23 24 #undef CONFIG_WATCHDOG 25 #define CONFIG_WATCHDOG_TIMEOUT 5000 26 27 /* Command line configuration */ 28 #include <config_cmd_default.h> 29 30 #define CONFIG_CMD_CACHE 31 #define CONFIG_CMD_ELF 32 #define CONFIG_CMD_FLASH 33 #undef CONFIG_CMD_I2C 34 #define CONFIG_CMD_MEMORY 35 #define CONFIG_CMD_MISC 36 #define CONFIG_CMD_MII 37 #define CONFIG_CMD_NET 38 #define CONFIG_CMD_PING 39 #define CONFIG_CMD_REGINFO 40 41 #define CONFIG_MCFFEC 42 #ifdef CONFIG_MCFFEC 43 # define CONFIG_MII 1 44 # define CONFIG_MII_INIT 1 45 # define CONFIG_SYS_DISCOVER_PHY 46 # define CONFIG_SYS_RX_ETH_BUFFER 8 47 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 48 # define CONFIG_HAS_ETH1 49 50 # define CONFIG_SYS_FEC0_PINMUX 0 51 # define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE 52 # define MCFFEC_TOUT_LOOP 50000 53 /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */ 54 # ifndef CONFIG_SYS_DISCOVER_PHY 55 # define FECDUPLEX FULL 56 # define FECSPEED _100BASET 57 # else 58 # ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN 59 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 60 # endif 61 # endif /* CONFIG_SYS_DISCOVER_PHY */ 62 #endif 63 64 /* Timer */ 65 #define CONFIG_MCFTMR 66 #undef CONFIG_MCFPIT 67 68 /* I2C */ 69 #define CONFIG_SYS_I2C 70 #define CONFIG_SYS_I2C_FSL 71 #define CONFIG_SYS_FSL_I2C_SPEED 80000 72 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 73 #define CONFIG_SYS_FSL_I2C_OFFSET 0x58000 74 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR 75 76 #define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */ 77 #define CONFIG_UDP_CHECKSUM 78 79 #ifdef CONFIG_MCFFEC 80 # define CONFIG_ETHADDR 00:e0:0c:bc:e5:60 81 # define CONFIG_IPADDR 192.162.1.2 82 # define CONFIG_NETMASK 255.255.255.0 83 # define CONFIG_SERVERIP 192.162.1.1 84 # define CONFIG_GATEWAYIP 192.162.1.1 85 # define CONFIG_OVERWRITE_ETHADDR_ONCE 86 #endif /* CONFIG_MCFFEC */ 87 88 #define CONFIG_HOSTNAME M5208EVBe 89 #define CONFIG_EXTRA_ENV_SETTINGS \ 90 "netdev=eth0\0" \ 91 "loadaddr=40010000\0" \ 92 "u-boot=u-boot.bin\0" \ 93 "load=tftp ${loadaddr) ${u-boot}\0" \ 94 "upd=run load; run prog\0" \ 95 "prog=prot off 0 3ffff;" \ 96 "era 0 3ffff;" \ 97 "cp.b ${loadaddr} 0 ${filesize};" \ 98 "save\0" \ 99 "" 100 101 #define CONFIG_PRAM 512 /* 512 KB */ 102 #define CONFIG_SYS_PROMPT "-> " 103 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 104 105 #ifdef CONFIG_CMD_KGDB 106 # define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 107 #else 108 # define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 109 #endif 110 111 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 112 #define CONFIG_SYS_MAXARGS 16 /* max number of cmd args */ 113 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Arg Buf Sz */ 114 #define CONFIG_SYS_LOAD_ADDR 0x40010000 115 116 #define CONFIG_SYS_HZ 1000 117 #define CONFIG_SYS_CLK 166666666 /* CPU Core Clock */ 118 #define CONFIG_SYS_PLL_ODR 0x36 119 #define CONFIG_SYS_PLL_FDR 0x7D 120 121 #define CONFIG_SYS_MBAR 0xFC000000 122 123 /* 124 * Low Level Configuration Settings 125 * (address mappings, register initial values, etc.) 126 * You should know what you are doing if you make changes here. 127 */ 128 /* Definitions for initial stack pointer and data area (in DPRAM) */ 129 #define CONFIG_SYS_INIT_RAM_ADDR 0x80000000 130 #define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in internal SRAM */ 131 #define CONFIG_SYS_INIT_RAM_CTRL 0x221 132 #define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - 0x10) 133 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 134 135 /* 136 * Start addresses for the final memory configuration 137 * (Set up by the startup code) 138 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 139 */ 140 #define CONFIG_SYS_SDRAM_BASE 0x40000000 141 #define CONFIG_SYS_SDRAM_SIZE 32 /* SDRAM size in MB */ 142 #define CONFIG_SYS_SDRAM_CFG1 0x43711630 143 #define CONFIG_SYS_SDRAM_CFG2 0x56670000 144 #define CONFIG_SYS_SDRAM_CTRL 0xE1002000 145 #define CONFIG_SYS_SDRAM_EMOD 0x80010000 146 #define CONFIG_SYS_SDRAM_MODE 0x00CD0000 147 148 #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE + 0x400 149 #define CONFIG_SYS_MEMTEST_END ((CONFIG_SYS_SDRAM_SIZE - 3) << 20) 150 151 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) 152 #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ 153 154 #define CONFIG_SYS_BOOTPARAMS_LEN 64*1024 155 #define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ 156 157 /* 158 * For booting Linux, the board info and command line data 159 * have to be in the first 8 MB of memory, since this is 160 * the maximum mapped by the Linux kernel during initialization ?? 161 */ 162 #define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20)) 163 #define CONFIG_SYS_BOOTM_LEN (CONFIG_SYS_SDRAM_SIZE << 20) 164 165 /* FLASH organization */ 166 #define CONFIG_SYS_FLASH_CFI 167 #ifdef CONFIG_SYS_FLASH_CFI 168 # define CONFIG_FLASH_CFI_DRIVER 1 169 # define CONFIG_SYS_FLASH_SIZE 0x800000 /* Max size that the board might have */ 170 # define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT 171 # define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ 172 # define CONFIG_SYS_MAX_FLASH_SECT 254 /* max number of sectors on one chip */ 173 # define CONFIG_SYS_FLASH_PROTECTION /* "Real" (hardware) sectors protection */ 174 #endif 175 176 #define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE 177 178 /* 179 * Configuration for environment 180 * Environment is embedded in u-boot in the second sector of the flash 181 */ 182 #define CONFIG_ENV_OFFSET 0x2000 183 #define CONFIG_ENV_SIZE 0x1000 184 #define CONFIG_ENV_SECT_SIZE 0x2000 185 #define CONFIG_ENV_IS_IN_FLASH 1 186 187 /* Cache Configuration */ 188 #define CONFIG_SYS_CACHELINE_SIZE 16 189 190 #define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 191 CONFIG_SYS_INIT_RAM_SIZE - 8) 192 #define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 193 CONFIG_SYS_INIT_RAM_SIZE - 4) 194 #define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV | CF_CACR_INVI) 195 #define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ 196 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ 197 CF_ACR_EN | CF_ACR_SM_ALL) 198 #define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CINV | \ 199 CF_CACR_DISD | CF_CACR_INVI | \ 200 CF_CACR_CEIB | CF_CACR_DCM | \ 201 CF_CACR_EUSP) 202 203 /* Chipselect bank definitions */ 204 /* 205 * CS0 - NOR Flash 206 * CS1 - Available 207 * CS2 - Available 208 * CS3 - Available 209 * CS4 - Available 210 * CS5 - Available 211 */ 212 #define CONFIG_SYS_CS0_BASE 0 213 #define CONFIG_SYS_CS0_MASK 0x007F0001 214 #define CONFIG_SYS_CS0_CTRL 0x00001FA0 215 216 #endif /* _M5208EVBE_H */ 217