1 /* 2 * Copyright 2011-2012 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 /* 8 * BSC9131 RDB board configuration file 9 */ 10 11 #ifndef __CONFIG_H 12 #define __CONFIG_H 13 14 #define CONFIG_DISPLAY_BOARDINFO 15 16 #ifdef CONFIG_BSC9131RDB 17 #define CONFIG_BSC9131 18 #define CONFIG_NAND_FSL_IFC 19 #endif 20 21 #ifdef CONFIG_SPIFLASH 22 #define CONFIG_RAMBOOT_SPIFLASH 23 #define CONFIG_SYS_RAMBOOT 24 #define CONFIG_SYS_EXTRA_ENV_RELOC 25 #define CONFIG_SYS_TEXT_BASE 0x11000000 26 #define CONFIG_RESET_VECTOR_ADDRESS 0x110bfffc 27 #endif 28 29 #ifdef CONFIG_NAND 30 #define CONFIG_SPL_INIT_MINIMAL 31 #define CONFIG_SPL_SERIAL_SUPPORT 32 #define CONFIG_SPL_NAND_SUPPORT 33 #define CONFIG_SPL_NAND_BOOT 34 #define CONFIG_SPL_FLUSH_IMAGE 35 #define CONFIG_SPL_TARGET "u-boot-with-spl.bin" 36 37 #define CONFIG_SYS_TEXT_BASE 0x00201000 38 #define CONFIG_SPL_TEXT_BASE 0xFFFFE000 39 #define CONFIG_SPL_MAX_SIZE 8192 40 #define CONFIG_SPL_RELOC_TEXT_BASE 0x00100000 41 #define CONFIG_SPL_RELOC_STACK 0x00100000 42 #define CONFIG_SYS_NAND_U_BOOT_SIZE ((768 << 10) - 0x2000) 43 #define CONFIG_SYS_NAND_U_BOOT_DST (0x00200000 - CONFIG_SPL_MAX_SIZE) 44 #define CONFIG_SYS_NAND_U_BOOT_START 0x00200000 45 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0 46 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" 47 #endif 48 49 #ifdef CONFIG_SPL_BUILD 50 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE 51 #else 52 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 53 #endif 54 55 56 /* High Level Configuration Options */ 57 #define CONFIG_BOOKE /* BOOKE */ 58 #define CONFIG_E500 /* BOOKE e500 family */ 59 #define CONFIG_FSL_IFC /* Enable IFC Support */ 60 #define CONFIG_FSL_CAAM /* Enable SEC/CAAM */ 61 62 #define CONFIG_FSL_LAW /* Use common FSL init code */ 63 #define CONFIG_TSEC_ENET 64 #define CONFIG_ENV_OVERWRITE 65 66 #define CONFIG_DDR_CLK_FREQ 66666666 /* DDRCLK on 9131 RDB */ 67 #if defined(CONFIG_SYS_CLK_100) 68 #define CONFIG_SYS_CLK_FREQ 100000000 /* SYSCLK for 9131 RDB */ 69 #else 70 #define CONFIG_SYS_CLK_FREQ 66666666 /* SYSCLK for 9131 RDB */ 71 #endif 72 73 #define CONFIG_HWCONFIG 74 /* 75 * These can be toggled for performance analysis, otherwise use default. 76 */ 77 #define CONFIG_L2_CACHE /* toggle L2 cache */ 78 #define CONFIG_BTB /* enable branch predition */ 79 80 #define CONFIG_SYS_MEMTEST_START 0x01000000 /* memtest works on */ 81 #define CONFIG_SYS_MEMTEST_END 0x01ffffff 82 83 /* DDR Setup */ 84 #define CONFIG_SYS_FSL_DDR3 85 #undef CONFIG_SYS_DDR_RAW_TIMING 86 #undef CONFIG_DDR_SPD 87 #define CONFIG_SYS_SPD_BUS_NUM 0 88 #define SPD_EEPROM_ADDRESS 0x52 /* I2C access */ 89 90 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 91 92 #ifndef __ASSEMBLY__ 93 extern unsigned long get_sdram_size(void); 94 #endif 95 #define CONFIG_SYS_SDRAM_SIZE get_sdram_size() /* DDR size */ 96 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 97 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 98 99 #define CONFIG_NUM_DDR_CONTROLLERS 1 100 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 101 #define CONFIG_CHIP_SELECTS_PER_CTRL 1 102 103 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f 104 #define CONFIG_SYS_DDR_CS0_CONFIG 0x80014302 105 #define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000 106 107 #define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef 108 #define CONFIG_SYS_DDR_INIT_ADDR 0x00000000 109 #define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000 110 #define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000 111 112 #define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600 113 #define CONFIG_SYS_DDR_SR_CNTR 0x00000000 114 #define CONFIG_SYS_DDR_RCW_1 0x00000000 115 #define CONFIG_SYS_DDR_RCW_2 0x00000000 116 #define CONFIG_SYS_DDR_CONTROL 0xC70C0000 /* Type = DDR3 */ 117 #define CONFIG_SYS_DDR_CONTROL_2 0x24401000 118 #define CONFIG_SYS_DDR_TIMING_4 0x00000001 119 #define CONFIG_SYS_DDR_TIMING_5 0x02401400 120 121 #define CONFIG_SYS_DDR_TIMING_3_800 0x00030000 122 #define CONFIG_SYS_DDR_TIMING_0_800 0x00110104 123 #define CONFIG_SYS_DDR_TIMING_1_800 0x6f6b8644 124 #define CONFIG_SYS_DDR_TIMING_2_800 0x0fa888cf 125 #define CONFIG_SYS_DDR_CLK_CTRL_800 0x03000000 126 #define CONFIG_SYS_DDR_MODE_1_800 0x00441420 127 #define CONFIG_SYS_DDR_MODE_2_800 0x8000c000 128 #define CONFIG_SYS_DDR_INTERVAL_800 0x0c300100 129 #define CONFIG_SYS_DDR_WRLVL_CONTROL_800 0x8675f608 130 131 /* 132 * Base addresses -- Note these are effective addresses where the 133 * actual resources get mapped (not physical addresses) 134 */ 135 /* relocated CCSRBAR */ 136 #define CONFIG_SYS_CCSRBAR CONFIG_SYS_CCSRBAR_DEFAULT 137 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR_DEFAULT 138 139 #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses */ 140 /* CONFIG_SYS_IMMR */ 141 /* DSP CCSRBAR */ 142 #define CONFIG_SYS_FSL_DSP_CCSRBAR CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT 143 #define CONFIG_SYS_FSL_DSP_CCSRBAR_PHYS CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT 144 145 /* 146 * Memory map 147 * 148 * 0x0000_0000 0x3FFF_FFFF DDR 1G cacheable 149 * 0x8800_0000 0x8810_0000 IFC internal SRAM 1M 150 * 0xB000_0000 0xB0FF_FFFF DSP core M2 memory 16M 151 * 0xC100_0000 0xC13F_FFFF MAPLE-2F 4M 152 * 0xC1F0_0000 0xC1F3_FFFF PA L2 SRAM Region 0 256K 153 * 0xC1F8_0000 0xC1F9_FFFF PA L2 SRAM Region 1 128K 154 * 0xFED0_0000 0xFED0_3FFF SEC Secured RAM 16K 155 * 0xFF60_0000 0xFF6F_FFFF DSP CCSR 1M 156 * 0xFF70_0000 0xFF7F_FFFF PA CCSR 1M 157 * 0xFF80_0000 0xFFFF_FFFF Boot Page & NAND flash buffer 8M 158 * 159 */ 160 161 /* 162 * IFC Definitions 163 */ 164 #define CONFIG_SYS_NO_FLASH 165 166 /* NAND Flash on IFC */ 167 #define CONFIG_SYS_NAND_BASE 0xff800000 168 #define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE 169 170 #define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 171 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit*/ \ 172 | CSPR_MSEL_NAND /* MSEL = NAND */ \ 173 | CSPR_V) 174 #define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) 175 176 #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ 177 | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ 178 | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ 179 | CSOR_NAND_RAL_2 /* RAL = 2Byes */ \ 180 | CSOR_NAND_PGS_2K /* Page Size = 2K */ \ 181 | CSOR_NAND_SPRZ_64 /* Spare size = 64 */ \ 182 | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ 183 184 /* NAND Flash Timing Params */ 185 #define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x03) \ 186 | FTIM0_NAND_TWP(0x05) \ 187 | FTIM0_NAND_TWCHT(0x02) \ 188 | FTIM0_NAND_TWH(0x04)) 189 #define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x1C) \ 190 | FTIM1_NAND_TWBE(0x1E) \ 191 | FTIM1_NAND_TRR(0x07) \ 192 | FTIM1_NAND_TRP(0x05)) 193 #define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x08) \ 194 | FTIM2_NAND_TREH(0x04) \ 195 | FTIM2_NAND_TWHRE(0x11)) 196 #define CONFIG_SYS_NAND_FTIM3 FTIM3_NAND_TWW(0x04) 197 198 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } 199 #define CONFIG_SYS_MAX_NAND_DEVICE 1 200 #define CONFIG_CMD_NAND 201 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) 202 203 #define CONFIG_SYS_NAND_DDR_LAW 11 204 205 /* Set up IFC registers for boot location NAND */ 206 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR 207 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK 208 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR 209 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 210 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 211 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 212 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 213 214 #define CONFIG_BOARD_EARLY_INIT_F /* Call board_pre_init */ 215 216 #define CONFIG_SYS_INIT_RAM_LOCK 217 #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */ 218 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000/* End of used area in RAM */ 219 220 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE \ 221 - GENERATED_GBL_DATA_SIZE) 222 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 223 224 #define CONFIG_SYS_MONITOR_LEN (768 * 1024) 225 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc*/ 226 227 /* Serial Port */ 228 #define CONFIG_CONS_INDEX 1 229 #undef CONFIG_SERIAL_SOFTWARE_FIFO 230 #define CONFIG_SYS_NS16550_SERIAL 231 #define CONFIG_SYS_NS16550_REG_SIZE 1 232 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 233 #ifdef CONFIG_SPL_BUILD 234 #define CONFIG_NS16550_MIN_FUNCTIONS 235 #endif 236 237 #define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */ 238 239 #define CONFIG_SYS_BAUDRATE_TABLE \ 240 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 241 242 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 243 244 /* Use the HUSH parser */ 245 #define CONFIG_SYS_HUSH_PARSER 246 #ifdef CONFIG_SYS_HUSH_PARSER 247 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " 248 #endif 249 250 #define CONFIG_SYS_I2C 251 #define CONFIG_SYS_I2C_FSL 252 #define CONFIG_SYS_FSL_I2C_SPEED 400000 253 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 254 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 255 256 /* I2C EEPROM */ 257 #define CONFIG_CMD_EEPROM 258 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 259 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 260 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 261 262 #define CONFIG_CMD_I2C 263 264 265 /* eSPI - Enhanced SPI */ 266 #ifdef CONFIG_FSL_ESPI 267 #define CONFIG_CMD_SF 268 #define CONFIG_SF_DEFAULT_SPEED 10000000 269 #define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 270 #endif 271 272 #if defined(CONFIG_TSEC_ENET) 273 274 #define CONFIG_MII /* MII PHY management */ 275 #define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ 276 #define CONFIG_TSEC1 1 277 #define CONFIG_TSEC1_NAME "eTSEC1" 278 #define CONFIG_TSEC2 1 279 #define CONFIG_TSEC2_NAME "eTSEC2" 280 281 #define TSEC1_PHY_ADDR 0 282 #define TSEC2_PHY_ADDR 3 283 284 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 285 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 286 287 #define TSEC1_PHYIDX 0 288 289 #define TSEC2_PHYIDX 0 290 291 #define CONFIG_ETHPRIME "eTSEC1" 292 293 #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ 294 295 #endif /* CONFIG_TSEC_ENET */ 296 297 /* 298 * Environment 299 */ 300 #if defined(CONFIG_RAMBOOT_SPIFLASH) 301 #define CONFIG_ENV_IS_IN_SPI_FLASH 302 #define CONFIG_ENV_SPI_BUS 0 303 #define CONFIG_ENV_SPI_CS 0 304 #define CONFIG_ENV_SPI_MAX_HZ 10000000 305 #define CONFIG_ENV_SPI_MODE 0 306 #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ 307 #define CONFIG_ENV_SECT_SIZE 0x10000 308 #define CONFIG_ENV_SIZE 0x2000 309 #elif defined(CONFIG_NAND) 310 #define CONFIG_ENV_IS_IN_NAND 311 #define CONFIG_SYS_EXTRA_ENV_RELOC 312 #define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE 313 #define CONFIG_ENV_OFFSET ((768 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE) 314 #define CONFIG_ENV_RANGE (3 * CONFIG_ENV_SIZE) 315 #elif defined(CONFIG_SYS_RAMBOOT) 316 #define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */ 317 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) 318 #define CONFIG_ENV_SIZE 0x2000 319 #endif 320 321 #define CONFIG_LOADS_ECHO /* echo on for serial download */ 322 #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ 323 324 /* 325 * Command line configuration. 326 */ 327 #define CONFIG_CMD_DHCP 328 #define CONFIG_CMD_ERRATA 329 #define CONFIG_CMD_EXT2 330 #define CONFIG_CMD_FAT 331 #define CONFIG_CMD_IRQ 332 #define CONFIG_CMD_MII 333 #define CONFIG_DOS_PARTITION 334 #define CONFIG_CMD_PING 335 #define CONFIG_CMD_REGINFO 336 337 /* 338 * Miscellaneous configurable options 339 */ 340 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 341 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 342 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 343 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 344 345 #if defined(CONFIG_CMD_KGDB) 346 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 347 #else 348 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 349 #endif 350 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) 351 /* Print Buffer Size */ 352 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 353 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ 354 355 /* 356 * For booting Linux, the board info and command line data 357 * have to be in the first 64 MB of memory, since this is 358 * the maximum mapped by the Linux kernel during initialization. 359 */ 360 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux */ 361 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 362 363 #if defined(CONFIG_CMD_KGDB) 364 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 365 #endif 366 367 /* Hash command with SHA acceleration supported in hardware */ 368 #ifdef CONFIG_FSL_CAAM 369 #define CONFIG_CMD_HASH 370 #define CONFIG_SHA_HW_ACCEL 371 #endif 372 373 #define CONFIG_USB_EHCI 374 375 #ifdef CONFIG_USB_EHCI 376 #define CONFIG_CMD_USB 377 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 378 #define CONFIG_USB_EHCI_FSL 379 #define CONFIG_USB_STORAGE 380 #define CONFIG_HAS_FSL_DR_USB 381 #endif 382 383 /* 384 * Dynamic MTD Partition support with mtdparts 385 */ 386 #define CONFIG_MTD_DEVICE 387 #define CONFIG_MTD_PARTITIONS 388 #define CONFIG_CMD_MTDPARTS 389 #define MTDIDS_DEFAULT "nand0=ff800000.flash," 390 #define MTDPARTS_DEFAULT "mtdparts=ff800000.flash:1m(uboot)," \ 391 "8m(kernel),512k(dtb),-(fs)" 392 /* 393 * Override partitions in device tree using info 394 * in "mtdparts" environment variable 395 */ 396 #ifdef CONFIG_CMD_MTDPARTS 397 #define CONFIG_FDT_FIXUP_PARTITIONS 398 #endif 399 400 /* 401 * Environment Configuration 402 */ 403 404 #if defined(CONFIG_TSEC_ENET) 405 #define CONFIG_HAS_ETH0 406 #endif 407 408 #define CONFIG_HOSTNAME BSC9131rdb 409 #define CONFIG_ROOTPATH "/opt/nfsroot" 410 #define CONFIG_BOOTFILE "uImage" 411 #define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */ 412 413 #define CONFIG_BAUDRATE 115200 414 #define CONFIG_BOOTDELAY 10 /* -1 disable auto-boot */ 415 416 #define CONFIG_EXTRA_ENV_SETTINGS \ 417 "netdev=eth0\0" \ 418 "uboot=" CONFIG_UBOOTPATH "\0" \ 419 "loadaddr=1000000\0" \ 420 "bootfile=uImage\0" \ 421 "consoledev=ttyS0\0" \ 422 "ramdiskaddr=2000000\0" \ 423 "ramdiskfile=rootfs.ext2.gz.uboot\0" \ 424 "fdtaddr=c00000\0" \ 425 "fdtfile=bsc9131rdb.dtb\0" \ 426 "bdev=sda1\0" \ 427 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0" \ 428 "bootm_size=0x37000000\0" \ 429 "othbootargs=ramdisk_size=600000 " \ 430 "default_hugepagesz=256m hugepagesz=256m hugepages=1\0" \ 431 "usbext2boot=setenv bootargs root=/dev/ram rw " \ 432 "console=$consoledev,$baudrate $othbootargs; " \ 433 "usb start;" \ 434 "ext2load usb 0:4 $loadaddr $bootfile;" \ 435 "ext2load usb 0:4 $fdtaddr $fdtfile;" \ 436 "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \ 437 "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \ 438 439 #define CONFIG_RAMBOOTCOMMAND \ 440 "setenv bootargs root=/dev/ram rw " \ 441 "console=$consoledev,$baudrate $othbootargs; " \ 442 "tftp $ramdiskaddr $ramdiskfile;" \ 443 "tftp $loadaddr $bootfile;" \ 444 "tftp $fdtaddr $fdtfile;" \ 445 "bootm $loadaddr $ramdiskaddr $fdtaddr" 446 447 #define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND 448 449 #endif /* __CONFIG_H */ 450