1 /* 2 * Copyright 2011-2012 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 /* 8 * BSC9131 RDB board configuration file 9 */ 10 11 #ifndef __CONFIG_H 12 #define __CONFIG_H 13 14 #define CONFIG_NAND_FSL_IFC 15 16 #ifdef CONFIG_SPIFLASH 17 #define CONFIG_RAMBOOT_SPIFLASH 18 #define CONFIG_SYS_RAMBOOT 19 #define CONFIG_SYS_EXTRA_ENV_RELOC 20 #define CONFIG_SYS_TEXT_BASE 0x11000000 21 #define CONFIG_RESET_VECTOR_ADDRESS 0x110bfffc 22 #endif 23 24 #ifdef CONFIG_NAND 25 #define CONFIG_SPL_INIT_MINIMAL 26 #define CONFIG_SPL_NAND_BOOT 27 #define CONFIG_SPL_FLUSH_IMAGE 28 #define CONFIG_SPL_TARGET "u-boot-with-spl.bin" 29 30 #define CONFIG_SYS_TEXT_BASE 0x00201000 31 #define CONFIG_SPL_TEXT_BASE 0xFFFFE000 32 #define CONFIG_SPL_MAX_SIZE 8192 33 #define CONFIG_SPL_RELOC_TEXT_BASE 0x00100000 34 #define CONFIG_SPL_RELOC_STACK 0x00100000 35 #define CONFIG_SYS_NAND_U_BOOT_SIZE ((768 << 10) - 0x2000) 36 #define CONFIG_SYS_NAND_U_BOOT_DST (0x00200000 - CONFIG_SPL_MAX_SIZE) 37 #define CONFIG_SYS_NAND_U_BOOT_START 0x00200000 38 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0 39 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" 40 #endif 41 42 #ifdef CONFIG_SPL_BUILD 43 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE 44 #else 45 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 46 #endif 47 48 /* High Level Configuration Options */ 49 #define CONFIG_FSL_IFC /* Enable IFC Support */ 50 #define CONFIG_FSL_CAAM /* Enable SEC/CAAM */ 51 52 #define CONFIG_TSEC_ENET 53 #define CONFIG_ENV_OVERWRITE 54 55 #define CONFIG_DDR_CLK_FREQ 66666666 /* DDRCLK on 9131 RDB */ 56 #if defined(CONFIG_SYS_CLK_100) 57 #define CONFIG_SYS_CLK_FREQ 100000000 /* SYSCLK for 9131 RDB */ 58 #else 59 #define CONFIG_SYS_CLK_FREQ 66666666 /* SYSCLK for 9131 RDB */ 60 #endif 61 62 #define CONFIG_HWCONFIG 63 /* 64 * These can be toggled for performance analysis, otherwise use default. 65 */ 66 #define CONFIG_L2_CACHE /* toggle L2 cache */ 67 #define CONFIG_BTB /* enable branch predition */ 68 69 #define CONFIG_SYS_MEMTEST_START 0x01000000 /* memtest works on */ 70 #define CONFIG_SYS_MEMTEST_END 0x01ffffff 71 72 /* DDR Setup */ 73 #undef CONFIG_SYS_DDR_RAW_TIMING 74 #undef CONFIG_DDR_SPD 75 #define CONFIG_SYS_SPD_BUS_NUM 0 76 #define SPD_EEPROM_ADDRESS 0x52 /* I2C access */ 77 78 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 79 80 #ifndef __ASSEMBLY__ 81 extern unsigned long get_sdram_size(void); 82 #endif 83 #define CONFIG_SYS_SDRAM_SIZE get_sdram_size() /* DDR size */ 84 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 85 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 86 87 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 88 #define CONFIG_CHIP_SELECTS_PER_CTRL 1 89 90 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f 91 #define CONFIG_SYS_DDR_CS0_CONFIG 0x80014302 92 #define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000 93 94 #define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef 95 #define CONFIG_SYS_DDR_INIT_ADDR 0x00000000 96 #define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000 97 #define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000 98 99 #define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600 100 #define CONFIG_SYS_DDR_SR_CNTR 0x00000000 101 #define CONFIG_SYS_DDR_RCW_1 0x00000000 102 #define CONFIG_SYS_DDR_RCW_2 0x00000000 103 #define CONFIG_SYS_DDR_CONTROL 0xC70C0000 /* Type = DDR3 */ 104 #define CONFIG_SYS_DDR_CONTROL_2 0x24401000 105 #define CONFIG_SYS_DDR_TIMING_4 0x00000001 106 #define CONFIG_SYS_DDR_TIMING_5 0x02401400 107 108 #define CONFIG_SYS_DDR_TIMING_3_800 0x00030000 109 #define CONFIG_SYS_DDR_TIMING_0_800 0x00110104 110 #define CONFIG_SYS_DDR_TIMING_1_800 0x6f6b8644 111 #define CONFIG_SYS_DDR_TIMING_2_800 0x0fa888cf 112 #define CONFIG_SYS_DDR_CLK_CTRL_800 0x03000000 113 #define CONFIG_SYS_DDR_MODE_1_800 0x00441420 114 #define CONFIG_SYS_DDR_MODE_2_800 0x8000c000 115 #define CONFIG_SYS_DDR_INTERVAL_800 0x0c300100 116 #define CONFIG_SYS_DDR_WRLVL_CONTROL_800 0x8675f608 117 118 /* 119 * Base addresses -- Note these are effective addresses where the 120 * actual resources get mapped (not physical addresses) 121 */ 122 /* relocated CCSRBAR */ 123 #define CONFIG_SYS_CCSRBAR CONFIG_SYS_CCSRBAR_DEFAULT 124 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR_DEFAULT 125 126 #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses */ 127 /* CONFIG_SYS_IMMR */ 128 /* DSP CCSRBAR */ 129 #define CONFIG_SYS_FSL_DSP_CCSRBAR CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT 130 #define CONFIG_SYS_FSL_DSP_CCSRBAR_PHYS CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT 131 132 /* 133 * Memory map 134 * 135 * 0x0000_0000 0x3FFF_FFFF DDR 1G cacheable 136 * 0x8800_0000 0x8810_0000 IFC internal SRAM 1M 137 * 0xB000_0000 0xB0FF_FFFF DSP core M2 memory 16M 138 * 0xC100_0000 0xC13F_FFFF MAPLE-2F 4M 139 * 0xC1F0_0000 0xC1F3_FFFF PA L2 SRAM Region 0 256K 140 * 0xC1F8_0000 0xC1F9_FFFF PA L2 SRAM Region 1 128K 141 * 0xFED0_0000 0xFED0_3FFF SEC Secured RAM 16K 142 * 0xFF60_0000 0xFF6F_FFFF DSP CCSR 1M 143 * 0xFF70_0000 0xFF7F_FFFF PA CCSR 1M 144 * 0xFF80_0000 0xFFFF_FFFF Boot Page & NAND flash buffer 8M 145 * 146 */ 147 148 /* 149 * IFC Definitions 150 */ 151 #define CONFIG_SYS_NO_FLASH 152 153 /* NAND Flash on IFC */ 154 #define CONFIG_SYS_NAND_BASE 0xff800000 155 #define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE 156 157 #define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 158 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit*/ \ 159 | CSPR_MSEL_NAND /* MSEL = NAND */ \ 160 | CSPR_V) 161 #define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) 162 163 #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ 164 | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ 165 | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ 166 | CSOR_NAND_RAL_2 /* RAL = 2Byes */ \ 167 | CSOR_NAND_PGS_2K /* Page Size = 2K */ \ 168 | CSOR_NAND_SPRZ_64 /* Spare size = 64 */ \ 169 | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ 170 171 /* NAND Flash Timing Params */ 172 #define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x03) \ 173 | FTIM0_NAND_TWP(0x05) \ 174 | FTIM0_NAND_TWCHT(0x02) \ 175 | FTIM0_NAND_TWH(0x04)) 176 #define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x1C) \ 177 | FTIM1_NAND_TWBE(0x1E) \ 178 | FTIM1_NAND_TRR(0x07) \ 179 | FTIM1_NAND_TRP(0x05)) 180 #define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x08) \ 181 | FTIM2_NAND_TREH(0x04) \ 182 | FTIM2_NAND_TWHRE(0x11)) 183 #define CONFIG_SYS_NAND_FTIM3 FTIM3_NAND_TWW(0x04) 184 185 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } 186 #define CONFIG_SYS_MAX_NAND_DEVICE 1 187 #define CONFIG_CMD_NAND 188 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) 189 190 #define CONFIG_SYS_NAND_DDR_LAW 11 191 192 /* Set up IFC registers for boot location NAND */ 193 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR 194 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK 195 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR 196 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 197 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 198 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 199 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 200 201 #define CONFIG_BOARD_EARLY_INIT_F /* Call board_pre_init */ 202 203 #define CONFIG_SYS_INIT_RAM_LOCK 204 #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */ 205 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000/* End of used area in RAM */ 206 207 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE \ 208 - GENERATED_GBL_DATA_SIZE) 209 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 210 211 #define CONFIG_SYS_MONITOR_LEN (768 * 1024) 212 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc*/ 213 214 /* Serial Port */ 215 #define CONFIG_CONS_INDEX 1 216 #undef CONFIG_SERIAL_SOFTWARE_FIFO 217 #define CONFIG_SYS_NS16550_SERIAL 218 #define CONFIG_SYS_NS16550_REG_SIZE 1 219 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 220 #ifdef CONFIG_SPL_BUILD 221 #define CONFIG_NS16550_MIN_FUNCTIONS 222 #endif 223 224 #define CONFIG_SYS_BAUDRATE_TABLE \ 225 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 226 227 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 228 229 #define CONFIG_SYS_I2C 230 #define CONFIG_SYS_I2C_FSL 231 #define CONFIG_SYS_FSL_I2C_SPEED 400000 232 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 233 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 234 235 /* I2C EEPROM */ 236 #define CONFIG_CMD_EEPROM 237 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 238 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 239 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 240 241 /* eSPI - Enhanced SPI */ 242 #ifdef CONFIG_FSL_ESPI 243 #define CONFIG_SF_DEFAULT_SPEED 10000000 244 #define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 245 #endif 246 247 #if defined(CONFIG_TSEC_ENET) 248 249 #define CONFIG_MII /* MII PHY management */ 250 #define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ 251 #define CONFIG_TSEC1 1 252 #define CONFIG_TSEC1_NAME "eTSEC1" 253 #define CONFIG_TSEC2 1 254 #define CONFIG_TSEC2_NAME "eTSEC2" 255 256 #define TSEC1_PHY_ADDR 0 257 #define TSEC2_PHY_ADDR 3 258 259 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 260 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 261 262 #define TSEC1_PHYIDX 0 263 264 #define TSEC2_PHYIDX 0 265 266 #define CONFIG_ETHPRIME "eTSEC1" 267 268 #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ 269 270 #endif /* CONFIG_TSEC_ENET */ 271 272 /* 273 * Environment 274 */ 275 #if defined(CONFIG_RAMBOOT_SPIFLASH) 276 #define CONFIG_ENV_IS_IN_SPI_FLASH 277 #define CONFIG_ENV_SPI_BUS 0 278 #define CONFIG_ENV_SPI_CS 0 279 #define CONFIG_ENV_SPI_MAX_HZ 10000000 280 #define CONFIG_ENV_SPI_MODE 0 281 #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ 282 #define CONFIG_ENV_SECT_SIZE 0x10000 283 #define CONFIG_ENV_SIZE 0x2000 284 #elif defined(CONFIG_NAND) 285 #define CONFIG_ENV_IS_IN_NAND 286 #define CONFIG_SYS_EXTRA_ENV_RELOC 287 #define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE 288 #define CONFIG_ENV_OFFSET ((768 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE) 289 #define CONFIG_ENV_RANGE (3 * CONFIG_ENV_SIZE) 290 #elif defined(CONFIG_SYS_RAMBOOT) 291 #define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */ 292 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) 293 #define CONFIG_ENV_SIZE 0x2000 294 #endif 295 296 #define CONFIG_LOADS_ECHO /* echo on for serial download */ 297 #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ 298 299 /* 300 * Command line configuration. 301 */ 302 #define CONFIG_CMD_ERRATA 303 #define CONFIG_CMD_IRQ 304 #define CONFIG_DOS_PARTITION 305 #define CONFIG_CMD_REGINFO 306 307 /* 308 * Miscellaneous configurable options 309 */ 310 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 311 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 312 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 313 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 314 315 #if defined(CONFIG_CMD_KGDB) 316 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 317 #else 318 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 319 #endif 320 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) 321 /* Print Buffer Size */ 322 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 323 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ 324 325 /* 326 * For booting Linux, the board info and command line data 327 * have to be in the first 64 MB of memory, since this is 328 * the maximum mapped by the Linux kernel during initialization. 329 */ 330 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux */ 331 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 332 333 #if defined(CONFIG_CMD_KGDB) 334 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 335 #endif 336 337 /* Hash command with SHA acceleration supported in hardware */ 338 #ifdef CONFIG_FSL_CAAM 339 #define CONFIG_CMD_HASH 340 #define CONFIG_SHA_HW_ACCEL 341 #endif 342 343 #define CONFIG_USB_EHCI 344 345 #ifdef CONFIG_USB_EHCI 346 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 347 #define CONFIG_USB_EHCI_FSL 348 #define CONFIG_HAS_FSL_DR_USB 349 #endif 350 351 /* 352 * Dynamic MTD Partition support with mtdparts 353 */ 354 #define CONFIG_MTD_DEVICE 355 #define CONFIG_MTD_PARTITIONS 356 #define CONFIG_CMD_MTDPARTS 357 #define MTDIDS_DEFAULT "nand0=ff800000.flash," 358 #define MTDPARTS_DEFAULT "mtdparts=ff800000.flash:1m(uboot)," \ 359 "8m(kernel),512k(dtb),-(fs)" 360 361 /* 362 * Environment Configuration 363 */ 364 365 #if defined(CONFIG_TSEC_ENET) 366 #define CONFIG_HAS_ETH0 367 #endif 368 369 #define CONFIG_HOSTNAME BSC9131rdb 370 #define CONFIG_ROOTPATH "/opt/nfsroot" 371 #define CONFIG_BOOTFILE "uImage" 372 #define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */ 373 374 #define CONFIG_BAUDRATE 115200 375 376 #define CONFIG_EXTRA_ENV_SETTINGS \ 377 "netdev=eth0\0" \ 378 "uboot=" CONFIG_UBOOTPATH "\0" \ 379 "loadaddr=1000000\0" \ 380 "bootfile=uImage\0" \ 381 "consoledev=ttyS0\0" \ 382 "ramdiskaddr=2000000\0" \ 383 "ramdiskfile=rootfs.ext2.gz.uboot\0" \ 384 "fdtaddr=1e00000\0" \ 385 "fdtfile=bsc9131rdb.dtb\0" \ 386 "bdev=sda1\0" \ 387 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0" \ 388 "bootm_size=0x37000000\0" \ 389 "othbootargs=ramdisk_size=600000 " \ 390 "default_hugepagesz=256m hugepagesz=256m hugepages=1\0" \ 391 "usbext2boot=setenv bootargs root=/dev/ram rw " \ 392 "console=$consoledev,$baudrate $othbootargs; " \ 393 "usb start;" \ 394 "ext2load usb 0:4 $loadaddr $bootfile;" \ 395 "ext2load usb 0:4 $fdtaddr $fdtfile;" \ 396 "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \ 397 "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \ 398 399 #define CONFIG_RAMBOOTCOMMAND \ 400 "setenv bootargs root=/dev/ram rw " \ 401 "console=$consoledev,$baudrate $othbootargs; " \ 402 "tftp $ramdiskaddr $ramdiskfile;" \ 403 "tftp $loadaddr $bootfile;" \ 404 "tftp $fdtaddr $fdtfile;" \ 405 "bootm $loadaddr $ramdiskaddr $fdtaddr" 406 407 #define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND 408 409 #endif /* __CONFIG_H */ 410