1 /* 2 * Copyright 2011-2012 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 /* 8 * BSC9131 RDB board configuration file 9 */ 10 11 #ifndef __CONFIG_H 12 #define __CONFIG_H 13 14 #ifdef CONFIG_BSC9131RDB 15 #define CONFIG_BSC9131 16 #define CONFIG_NAND_FSL_IFC 17 #endif 18 19 #ifdef CONFIG_SPIFLASH 20 #define CONFIG_RAMBOOT_SPIFLASH 21 #define CONFIG_SYS_RAMBOOT 22 #define CONFIG_SYS_EXTRA_ENV_RELOC 23 #define CONFIG_SYS_TEXT_BASE 0x11000000 24 #define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc 25 #endif 26 27 #ifdef CONFIG_NAND 28 #define CONFIG_SPL 29 #define CONFIG_SPL_INIT_MINIMAL 30 #define CONFIG_SPL_SERIAL_SUPPORT 31 #define CONFIG_SPL_NAND_SUPPORT 32 #define CONFIG_SPL_NAND_MINIMAL 33 #define CONFIG_SPL_FLUSH_IMAGE 34 #define CONFIG_SPL_TARGET "u-boot-with-spl.bin" 35 36 #define CONFIG_SYS_TEXT_BASE 0x00201000 37 #define CONFIG_SPL_TEXT_BASE 0xFFFFE000 38 #define CONFIG_SPL_MAX_SIZE 8192 39 #define CONFIG_SPL_RELOC_TEXT_BASE 0x00100000 40 #define CONFIG_SPL_RELOC_STACK 0x00100000 41 #define CONFIG_SYS_NAND_U_BOOT_SIZE ((512 << 10) - 0x2000) 42 #define CONFIG_SYS_NAND_U_BOOT_DST (0x00200000 - CONFIG_SPL_MAX_SIZE) 43 #define CONFIG_SYS_NAND_U_BOOT_START 0x00200000 44 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0 45 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" 46 #endif 47 48 #ifdef CONFIG_SPL_BUILD 49 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE 50 #else 51 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 52 #endif 53 54 55 /* High Level Configuration Options */ 56 #define CONFIG_BOOKE /* BOOKE */ 57 #define CONFIG_E500 /* BOOKE e500 family */ 58 #define CONFIG_MPC85xx /* MPC8540/60/55/41/48/P1020/P2020/P1010,etc*/ 59 #define CONFIG_FSL_IFC /* Enable IFC Support */ 60 61 #define CONFIG_FSL_LAW /* Use common FSL init code */ 62 #define CONFIG_TSEC_ENET 63 #define CONFIG_ENV_OVERWRITE 64 65 #define CONFIG_DDR_CLK_FREQ 66666666 /* DDRCLK on 9131 RDB */ 66 #if defined(CONFIG_SYS_CLK_100) 67 #define CONFIG_SYS_CLK_FREQ 100000000 /* SYSCLK for 9131 RDB */ 68 #else 69 #define CONFIG_SYS_CLK_FREQ 66666666 /* SYSCLK for 9131 RDB */ 70 #endif 71 72 #define CONFIG_HWCONFIG 73 /* 74 * These can be toggled for performance analysis, otherwise use default. 75 */ 76 #define CONFIG_L2_CACHE /* toggle L2 cache */ 77 #define CONFIG_BTB /* enable branch predition */ 78 79 #define CONFIG_SYS_MEMTEST_START 0x01000000 /* memtest works on */ 80 #define CONFIG_SYS_MEMTEST_END 0x01ffffff 81 82 /* DDR Setup */ 83 #define CONFIG_FSL_DDR3 84 #undef CONFIG_SYS_DDR_RAW_TIMING 85 #undef CONFIG_DDR_SPD 86 #define CONFIG_SYS_SPD_BUS_NUM 0 87 #define SPD_EEPROM_ADDRESS 0x52 /* I2C access */ 88 89 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 90 91 #ifndef __ASSEMBLY__ 92 extern unsigned long get_sdram_size(void); 93 #endif 94 #define CONFIG_SYS_SDRAM_SIZE get_sdram_size() /* DDR size */ 95 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 96 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 97 98 #define CONFIG_NUM_DDR_CONTROLLERS 1 99 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 100 #define CONFIG_CHIP_SELECTS_PER_CTRL 1 101 102 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f 103 #define CONFIG_SYS_DDR_CS0_CONFIG 0x80014302 104 #define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000 105 106 #define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef 107 #define CONFIG_SYS_DDR_INIT_ADDR 0x00000000 108 #define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000 109 #define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000 110 111 #define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600 112 #define CONFIG_SYS_DDR_SR_CNTR 0x00000000 113 #define CONFIG_SYS_DDR_RCW_1 0x00000000 114 #define CONFIG_SYS_DDR_RCW_2 0x00000000 115 #define CONFIG_SYS_DDR_CONTROL 0xC70C0000 /* Type = DDR3 */ 116 #define CONFIG_SYS_DDR_CONTROL_2 0x24401000 117 #define CONFIG_SYS_DDR_TIMING_4 0x00000001 118 #define CONFIG_SYS_DDR_TIMING_5 0x02401400 119 120 #define CONFIG_SYS_DDR_TIMING_3_800 0x00030000 121 #define CONFIG_SYS_DDR_TIMING_0_800 0x00110104 122 #define CONFIG_SYS_DDR_TIMING_1_800 0x6f6b8644 123 #define CONFIG_SYS_DDR_TIMING_2_800 0x0fa888cf 124 #define CONFIG_SYS_DDR_CLK_CTRL_800 0x03000000 125 #define CONFIG_SYS_DDR_MODE_1_800 0x00441420 126 #define CONFIG_SYS_DDR_MODE_2_800 0x8000c000 127 #define CONFIG_SYS_DDR_INTERVAL_800 0x0c300100 128 #define CONFIG_SYS_DDR_WRLVL_CONTROL_800 0x8675f608 129 130 /* 131 * Base addresses -- Note these are effective addresses where the 132 * actual resources get mapped (not physical addresses) 133 */ 134 /* relocated CCSRBAR */ 135 #define CONFIG_SYS_CCSRBAR CONFIG_SYS_CCSRBAR_DEFAULT 136 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR_DEFAULT 137 138 #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses */ 139 /* CONFIG_SYS_IMMR */ 140 /* DSP CCSRBAR */ 141 #define CONFIG_SYS_FSL_DSP_CCSRBAR CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT 142 #define CONFIG_SYS_FSL_DSP_CCSRBAR_PHYS CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT 143 144 /* 145 * Memory map 146 * 147 * 0x0000_0000 0x3FFF_FFFF DDR 1G cacheable 148 * 0x8800_0000 0x8810_0000 IFC internal SRAM 1M 149 * 0xB000_0000 0xB0FF_FFFF DSP core M2 memory 16M 150 * 0xC100_0000 0xC13F_FFFF MAPLE-2F 4M 151 * 0xC1F0_0000 0xC1F3_FFFF PA L2 SRAM Region 0 256K 152 * 0xC1F8_0000 0xC1F9_FFFF PA L2 SRAM Region 1 128K 153 * 0xFED0_0000 0xFED0_3FFF SEC Secured RAM 16K 154 * 0xFF60_0000 0xFF6F_FFFF DSP CCSR 1M 155 * 0xFF70_0000 0xFF7F_FFFF PA CCSR 1M 156 * 0xFF80_0000 0xFFFF_FFFF Boot Page & NAND flash buffer 8M 157 * 158 */ 159 160 /* 161 * IFC Definitions 162 */ 163 #define CONFIG_SYS_NO_FLASH 164 165 /* NAND Flash on IFC */ 166 #define CONFIG_SYS_NAND_BASE 0xff800000 167 #define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE 168 169 #define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 170 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit*/ \ 171 | CSPR_MSEL_NAND /* MSEL = NAND */ \ 172 | CSPR_V) 173 #define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) 174 175 #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ 176 | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ 177 | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ 178 | CSOR_NAND_RAL_2 /* RAL = 2Byes */ \ 179 | CSOR_NAND_PGS_2K /* Page Size = 2K */ \ 180 | CSOR_NAND_SPRZ_64 /* Spare size = 64 */ \ 181 | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ 182 183 /* NAND Flash Timing Params */ 184 #define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x08) \ 185 | FTIM0_NAND_TWP(0x06) \ 186 | FTIM0_NAND_TWCHT(0x03) \ 187 | FTIM0_NAND_TWH(0x04)) 188 #define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x18) \ 189 | FTIM1_NAND_TWBE(0x23) \ 190 | FTIM1_NAND_TRR(0x08) \ 191 | FTIM1_NAND_TRP(0x05)) 192 #define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x08) \ 193 | FTIM2_NAND_TREH(0x04) \ 194 | FTIM2_NAND_TWHRE(0x3f)) 195 #define CONFIG_SYS_NAND_FTIM3 FTIM3_NAND_TWW(0x22) 196 197 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } 198 #define CONFIG_SYS_MAX_NAND_DEVICE 1 199 #define CONFIG_MTD_NAND_VERIFY_WRITE 200 #define CONFIG_CMD_NAND 201 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) 202 203 #define CONFIG_SYS_NAND_DDR_LAW 11 204 205 /* Set up IFC registers for boot location NAND */ 206 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR 207 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK 208 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR 209 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 210 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 211 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 212 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 213 214 #define CONFIG_BOARD_EARLY_INIT_F /* Call board_pre_init */ 215 216 #define CONFIG_SYS_INIT_RAM_LOCK 217 #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */ 218 #define CONFIG_SYS_INIT_RAM_END 0x00004000/* End of used area in RAM */ 219 220 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END \ 221 - GENERATED_GBL_DATA_SIZE) 222 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 223 224 #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon*/ 225 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc*/ 226 227 /* Serial Port */ 228 #define CONFIG_CONS_INDEX 1 229 #undef CONFIG_SERIAL_SOFTWARE_FIFO 230 #define CONFIG_SYS_NS16550 231 #define CONFIG_SYS_NS16550_SERIAL 232 #define CONFIG_SYS_NS16550_REG_SIZE 1 233 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 234 #ifdef CONFIG_SPL_BUILD 235 #define CONFIG_NS16550_MIN_FUNCTIONS 236 #endif 237 238 #define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */ 239 240 #define CONFIG_SYS_BAUDRATE_TABLE \ 241 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 242 243 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 244 245 /* Use the HUSH parser */ 246 #define CONFIG_SYS_HUSH_PARSER 247 #ifdef CONFIG_SYS_HUSH_PARSER 248 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " 249 #endif 250 251 /* 252 * Pass open firmware flat tree 253 */ 254 #define CONFIG_OF_LIBFDT 255 #define CONFIG_OF_BOARD_SETUP 256 #define CONFIG_OF_STDOUT_VIA_ALIAS 257 258 /* new uImage format support */ 259 #define CONFIG_FIT 260 #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ 261 262 #define CONFIG_SYS_I2C 263 #define CONFIG_SYS_I2C_FSL 264 #define CONFIG_SYS_FSL_I2C_SPEED 400000 265 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 266 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 267 268 /* I2C EEPROM */ 269 #define CONFIG_CMD_EEPROM 270 #define CONFIG_SYS_I2C_MULTI_EEPROMS 271 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 272 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 273 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 274 275 #define CONFIG_CMD_I2C 276 277 278 #define CONFIG_FSL_ESPI 279 /* eSPI - Enhanced SPI */ 280 #ifdef CONFIG_FSL_ESPI 281 #define CONFIG_SPI_FLASH 282 #define CONFIG_SPI_FLASH_SPANSION 283 #define CONFIG_CMD_SF 284 #define CONFIG_SF_DEFAULT_SPEED 10000000 285 #define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 286 #endif 287 288 #if defined(CONFIG_TSEC_ENET) 289 290 #define CONFIG_MII /* MII PHY management */ 291 #define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ 292 #define CONFIG_TSEC1 1 293 #define CONFIG_TSEC1_NAME "eTSEC1" 294 #define CONFIG_TSEC2 1 295 #define CONFIG_TSEC2_NAME "eTSEC2" 296 297 #define TSEC1_PHY_ADDR 0 298 #define TSEC2_PHY_ADDR 3 299 300 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 301 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 302 303 #define TSEC1_PHYIDX 0 304 305 #define TSEC2_PHYIDX 0 306 307 #define CONFIG_ETHPRIME "eTSEC1" 308 309 #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ 310 311 #endif /* CONFIG_TSEC_ENET */ 312 313 /* 314 * Environment 315 */ 316 #if defined(CONFIG_RAMBOOT_SPIFLASH) 317 #define CONFIG_ENV_IS_IN_SPI_FLASH 318 #define CONFIG_ENV_SPI_BUS 0 319 #define CONFIG_ENV_SPI_CS 0 320 #define CONFIG_ENV_SPI_MAX_HZ 10000000 321 #define CONFIG_ENV_SPI_MODE 0 322 #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ 323 #define CONFIG_ENV_SECT_SIZE 0x10000 324 #define CONFIG_ENV_SIZE 0x2000 325 #elif defined(CONFIG_NAND) 326 #define CONFIG_ENV_IS_IN_NAND 327 #define CONFIG_SYS_EXTRA_ENV_RELOC 328 #define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE 329 #define CONFIG_ENV_OFFSET ((512 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE) 330 #define CONFIG_ENV_RANGE (3 * CONFIG_ENV_SIZE) 331 #elif defined(CONFIG_SYS_RAMBOOT) 332 #define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */ 333 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) 334 #define CONFIG_ENV_SIZE 0x2000 335 #endif 336 337 #define CONFIG_LOADS_ECHO /* echo on for serial download */ 338 #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ 339 340 /* 341 * Command line configuration. 342 */ 343 #include <config_cmd_default.h> 344 345 #define CONFIG_CMD_DHCP 346 #define CONFIG_CMD_ERRATA 347 #define CONFIG_CMD_ELF 348 #define CONFIG_CMD_EXT2 349 #define CONFIG_CMD_FAT 350 #define CONFIG_CMD_IRQ 351 #define CONFIG_CMD_MII 352 #define CONFIG_DOS_PARTITION 353 #define CONFIG_CMD_PING 354 #define CONFIG_CMD_REGINFO 355 #define CONFIG_CMD_SETEXPR 356 357 /* 358 * Miscellaneous configurable options 359 */ 360 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 361 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 362 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 363 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 364 #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ 365 366 #if defined(CONFIG_CMD_KGDB) 367 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 368 #else 369 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 370 #endif 371 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) 372 /* Print Buffer Size */ 373 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 374 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ 375 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ 376 377 /* 378 * For booting Linux, the board info and command line data 379 * have to be in the first 64 MB of memory, since this is 380 * the maximum mapped by the Linux kernel during initialization. 381 */ 382 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux */ 383 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 384 385 #if defined(CONFIG_CMD_KGDB) 386 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 387 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 388 #endif 389 390 #define CONFIG_USB_EHCI 391 392 #ifdef CONFIG_USB_EHCI 393 #define CONFIG_CMD_USB 394 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 395 #define CONFIG_USB_EHCI_FSL 396 #define CONFIG_USB_STORAGE 397 #define CONFIG_HAS_FSL_DR_USB 398 #endif 399 400 /* 401 * Environment Configuration 402 */ 403 404 #if defined(CONFIG_TSEC_ENET) 405 #define CONFIG_HAS_ETH0 406 #endif 407 408 #define CONFIG_HOSTNAME BSC9131rdb 409 #define CONFIG_ROOTPATH "/opt/nfsroot" 410 #define CONFIG_BOOTFILE "uImage" 411 #define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */ 412 413 #define CONFIG_BAUDRATE 115200 414 415 #define CONFIG_EXTRA_ENV_SETTINGS \ 416 "netdev=eth0\0" \ 417 "uboot=" CONFIG_UBOOTPATH "\0" \ 418 "loadaddr=1000000\0" \ 419 "bootfile=uImage\0" \ 420 "consoledev=ttyS0\0" \ 421 "ramdiskaddr=2000000\0" \ 422 "ramdiskfile=rootfs.ext2.gz.uboot\0" \ 423 "fdtaddr=c00000\0" \ 424 "fdtfile=bsc9131rdb.dtb\0" \ 425 "bdev=sda1\0" \ 426 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0" \ 427 "bootm_size=0x37000000\0" \ 428 "othbootargs=ramdisk_size=600000 " \ 429 "default_hugepagesz=256m hugepagesz=256m hugepages=1\0" \ 430 "usbext2boot=setenv bootargs root=/dev/ram rw " \ 431 "console=$consoledev,$baudrate $othbootargs; " \ 432 "usb start;" \ 433 "ext2load usb 0:4 $loadaddr $bootfile;" \ 434 "ext2load usb 0:4 $fdtaddr $fdtfile;" \ 435 "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \ 436 "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \ 437 438 #define CONFIG_RAMBOOTCOMMAND \ 439 "setenv bootargs root=/dev/ram rw " \ 440 "console=$consoledev,$baudrate $othbootargs; " \ 441 "tftp $ramdiskaddr $ramdiskfile;" \ 442 "tftp $loadaddr $bootfile;" \ 443 "tftp $fdtaddr $fdtfile;" \ 444 "bootm $loadaddr $ramdiskaddr $fdtaddr" 445 446 #define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND 447 448 #endif /* __CONFIG_H */ 449