1 /* 2 * Copyright 2011-2012 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #ifndef __CONFIG_H 8 #define __CONFIG_H 9 10 #define CONFIG_DISPLAY_BOARDINFO 11 12 /* 13 * B4860 QDS board configuration file 14 */ 15 #define CONFIG_B4860QDS 16 #define CONFIG_PHYS_64BIT 17 18 #ifdef CONFIG_RAMBOOT_PBL 19 #define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/freescale/b4860qds/b4_pbi.cfg 20 #define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/b4860qds/b4_rcw.cfg 21 #ifndef CONFIG_NAND 22 #define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE 23 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc 24 #else 25 #define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT 26 #define CONFIG_SPL_ENV_SUPPORT 27 #define CONFIG_SPL_SERIAL_SUPPORT 28 #define CONFIG_SPL_FLUSH_IMAGE 29 #define CONFIG_SPL_TARGET "u-boot-with-spl.bin" 30 #define CONFIG_SPL_LIBGENERIC_SUPPORT 31 #define CONFIG_SPL_LIBCOMMON_SUPPORT 32 #define CONFIG_SPL_I2C_SUPPORT 33 #define CONFIG_SPL_DRIVERS_MISC_SUPPORT 34 #define CONFIG_FSL_LAW /* Use common FSL init code */ 35 #define CONFIG_SYS_TEXT_BASE 0x00201000 36 #define CONFIG_SPL_TEXT_BASE 0xFFFD8000 37 #define CONFIG_SPL_PAD_TO 0x40000 38 #define CONFIG_SPL_MAX_SIZE 0x28000 39 #define RESET_VECTOR_OFFSET 0x27FFC 40 #define BOOT_PAGE_OFFSET 0x27000 41 #define CONFIG_SPL_NAND_SUPPORT 42 #define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10) 43 #define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000 44 #define CONFIG_SYS_NAND_U_BOOT_START 0x00200000 45 #define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10) 46 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" 47 #define CONFIG_SPL_NAND_BOOT 48 #ifdef CONFIG_SPL_BUILD 49 #define CONFIG_SPL_SKIP_RELOCATE 50 #define CONFIG_SPL_COMMON_INIT_DDR 51 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE 52 #define CONFIG_SYS_NO_FLASH 53 #endif 54 #endif 55 #endif 56 57 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 58 /* Set 1M boot space */ 59 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) 60 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ 61 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) 62 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc 63 #define CONFIG_SYS_NO_FLASH 64 #endif 65 66 /* High Level Configuration Options */ 67 #define CONFIG_BOOKE 68 #define CONFIG_E500 /* BOOKE e500 family */ 69 #define CONFIG_E500MC /* BOOKE e500mc family */ 70 #define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ 71 #define CONFIG_MP /* support multiple processors */ 72 73 #ifndef CONFIG_SYS_TEXT_BASE 74 #define CONFIG_SYS_TEXT_BASE 0xeff40000 75 #endif 76 77 #ifndef CONFIG_RESET_VECTOR_ADDRESS 78 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc 79 #endif 80 81 #define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ 82 #define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS 83 #define CONFIG_FSL_IFC /* Enable IFC Support */ 84 #define CONFIG_FSL_CAAM /* Enable SEC/CAAM */ 85 #define CONFIG_PCI /* Enable PCI/PCIE */ 86 #define CONFIG_PCIE1 /* PCIE controler 1 */ 87 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ 88 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ 89 90 #ifndef CONFIG_PPC_B4420 91 #define CONFIG_SYS_SRIO 92 #define CONFIG_SRIO1 /* SRIO port 1 */ 93 #define CONFIG_SRIO2 /* SRIO port 2 */ 94 #define CONFIG_SRIO_PCIE_BOOT_MASTER 95 #endif 96 97 #define CONFIG_FSL_LAW /* Use common FSL init code */ 98 99 /* I2C bus multiplexer */ 100 #define I2C_MUX_PCA_ADDR 0x77 101 102 /* VSC Crossbar switches */ 103 #define CONFIG_VSC_CROSSBAR 104 #define I2C_CH_DEFAULT 0x8 105 #define I2C_CH_VSC3316 0xc 106 #define I2C_CH_VSC3308 0xd 107 108 #define VSC3316_TX_ADDRESS 0x70 109 #define VSC3316_RX_ADDRESS 0x71 110 #define VSC3308_TX_ADDRESS 0x02 111 #define VSC3308_RX_ADDRESS 0x03 112 113 /* IDT clock synthesizers */ 114 #define CONFIG_IDT8T49N222A 115 #define I2C_CH_IDT 0x9 116 117 #define IDT_SERDES1_ADDRESS 0x6E 118 #define IDT_SERDES2_ADDRESS 0x6C 119 120 /* Voltage monitor on channel 2*/ 121 #define I2C_MUX_CH_VOL_MONITOR 0xa 122 #define I2C_VOL_MONITOR_ADDR 0x40 123 #define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2 124 #define I2C_VOL_MONITOR_BUS_V_OVF 0x1 125 #define I2C_VOL_MONITOR_BUS_V_SHIFT 3 126 127 #define CONFIG_ZM7300 128 #define I2C_MUX_CH_DPM 0xa 129 #define I2C_DPM_ADDR 0x28 130 131 #define CONFIG_ENV_OVERWRITE 132 133 #ifdef CONFIG_SYS_NO_FLASH 134 #if !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) && !defined(CONFIG_RAMBOOT_PBL) 135 #define CONFIG_ENV_IS_NOWHERE 136 #endif 137 #else 138 #define CONFIG_FLASH_CFI_DRIVER 139 #define CONFIG_SYS_FLASH_CFI 140 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 141 #endif 142 143 #if defined(CONFIG_SPIFLASH) 144 #define CONFIG_SYS_EXTRA_ENV_RELOC 145 #define CONFIG_ENV_IS_IN_SPI_FLASH 146 #define CONFIG_ENV_SPI_BUS 0 147 #define CONFIG_ENV_SPI_CS 0 148 #define CONFIG_ENV_SPI_MAX_HZ 10000000 149 #define CONFIG_ENV_SPI_MODE 0 150 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ 151 #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ 152 #define CONFIG_ENV_SECT_SIZE 0x10000 153 #elif defined(CONFIG_SDCARD) 154 #define CONFIG_SYS_EXTRA_ENV_RELOC 155 #define CONFIG_ENV_IS_IN_MMC 156 #define CONFIG_SYS_MMC_ENV_DEV 0 157 #define CONFIG_ENV_SIZE 0x2000 158 #define CONFIG_ENV_OFFSET (512 * 1097) 159 #elif defined(CONFIG_NAND) 160 #define CONFIG_SYS_EXTRA_ENV_RELOC 161 #define CONFIG_ENV_IS_IN_NAND 162 #define CONFIG_ENV_SIZE 0x2000 163 #define CONFIG_ENV_OFFSET (10 * CONFIG_SYS_NAND_BLOCK_SIZE) 164 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 165 #define CONFIG_ENV_IS_IN_REMOTE 166 #define CONFIG_ENV_ADDR 0xffe20000 167 #define CONFIG_ENV_SIZE 0x2000 168 #elif defined(CONFIG_ENV_IS_NOWHERE) 169 #define CONFIG_ENV_SIZE 0x2000 170 #else 171 #define CONFIG_ENV_IS_IN_FLASH 172 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) 173 #define CONFIG_ENV_SIZE 0x2000 174 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 175 #endif 176 177 #ifndef __ASSEMBLY__ 178 unsigned long get_board_sys_clk(void); 179 unsigned long get_board_ddr_clk(void); 180 #endif 181 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk() /* sysclk for MPC85xx */ 182 #define CONFIG_DDR_CLK_FREQ get_board_ddr_clk() 183 184 /* 185 * These can be toggled for performance analysis, otherwise use default. 186 */ 187 #define CONFIG_SYS_CACHE_STASHING 188 #define CONFIG_BTB /* toggle branch predition */ 189 #define CONFIG_DDR_ECC 190 #ifdef CONFIG_DDR_ECC 191 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 192 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 193 #endif 194 195 #define CONFIG_ENABLE_36BIT_PHYS 196 197 #ifdef CONFIG_PHYS_64BIT 198 #define CONFIG_ADDR_MAP 199 #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ 200 #endif 201 202 #if 0 203 #define CONFIG_POST CONFIG_SYS_POST_MEMORY /* test POST memory test */ 204 #endif 205 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 206 #define CONFIG_SYS_MEMTEST_END 0x00400000 207 #define CONFIG_SYS_ALT_MEMTEST 208 #define CONFIG_PANIC_HANG /* do not reset board on panic */ 209 210 /* 211 * Config the L3 Cache as L3 SRAM 212 */ 213 #define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000 214 #define CONFIG_SYS_L3_SIZE 256 << 10 215 #define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024) 216 #ifdef CONFIG_NAND 217 #define CONFIG_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024) 218 #endif 219 #define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 12 * 1024) 220 #define CONFIG_SPL_RELOC_MALLOC_SIZE (30 << 10) 221 #define CONFIG_SPL_RELOC_STACK (CONFIG_SPL_GD_ADDR + 64 * 1024) 222 #define CONFIG_SPL_RELOC_STACK_SIZE (22 << 10) 223 224 #ifdef CONFIG_PHYS_64BIT 225 #define CONFIG_SYS_DCSRBAR 0xf0000000 226 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull 227 #endif 228 229 /* EEPROM */ 230 #define CONFIG_ID_EEPROM 231 #define CONFIG_SYS_I2C_EEPROM_NXID 232 #define CONFIG_SYS_EEPROM_BUS_NUM 0 233 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 234 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 235 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 236 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 237 238 /* 239 * DDR Setup 240 */ 241 #define CONFIG_VERY_BIG_RAM 242 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 243 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 244 245 /* CONFIG_NUM_DDR_CONTROLLERS is defined in include/asm/config_mpc85xx.h */ 246 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 247 #define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) 248 249 #define CONFIG_DDR_SPD 250 #define CONFIG_SYS_DDR_RAW_TIMING 251 #define CONFIG_SYS_FSL_DDR3 252 #ifndef CONFIG_SPL_BUILD 253 #define CONFIG_FSL_DDR_INTERACTIVE 254 #endif 255 256 #define CONFIG_SYS_SPD_BUS_NUM 0 257 #define SPD_EEPROM_ADDRESS1 0x51 258 #define SPD_EEPROM_ADDRESS2 0x53 259 260 #define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 261 #define CONFIG_SYS_SDRAM_SIZE 2048 /* for fixed parameter use */ 262 263 /* 264 * IFC Definitions 265 */ 266 #define CONFIG_SYS_FLASH_BASE 0xe0000000 267 #ifdef CONFIG_PHYS_64BIT 268 #define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) 269 #else 270 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE 271 #endif 272 273 #define CONFIG_SYS_NOR0_CSPR_EXT (0xf) 274 #define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \ 275 + 0x8000000) | \ 276 CSPR_PORT_SIZE_16 | \ 277 CSPR_MSEL_NOR | \ 278 CSPR_V) 279 #define CONFIG_SYS_NOR1_CSPR_EXT (0xf) 280 #define CONFIG_SYS_NOR1_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ 281 CSPR_PORT_SIZE_16 | \ 282 CSPR_MSEL_NOR | \ 283 CSPR_V) 284 #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128 * 1024 * 1024) 285 /* NOR Flash Timing Params */ 286 #define CONFIG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(4) 287 #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x01) | \ 288 FTIM0_NOR_TEADC(0x04) | \ 289 FTIM0_NOR_TEAHC(0x20)) 290 #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ 291 FTIM1_NOR_TRAD_NOR(0x1A) |\ 292 FTIM1_NOR_TSEQRAD_NOR(0x13)) 293 #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x01) | \ 294 FTIM2_NOR_TCH(0x0E) | \ 295 FTIM2_NOR_TWPH(0x0E) | \ 296 FTIM2_NOR_TWP(0x1c)) 297 #define CONFIG_SYS_NOR_FTIM3 0x0 298 299 #define CONFIG_SYS_FLASH_QUIET_TEST 300 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 301 302 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ 303 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 304 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 305 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 306 307 #define CONFIG_SYS_FLASH_EMPTY_INFO 308 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS \ 309 + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS} 310 311 #define CONFIG_FSL_QIXIS /* use common QIXIS code */ 312 #define CONFIG_FSL_QIXIS_V2 313 #define QIXIS_BASE 0xffdf0000 314 #ifdef CONFIG_PHYS_64BIT 315 #define QIXIS_BASE_PHYS (0xf00000000ull | QIXIS_BASE) 316 #else 317 #define QIXIS_BASE_PHYS QIXIS_BASE 318 #endif 319 #define QIXIS_LBMAP_SWITCH 0x01 320 #define QIXIS_LBMAP_MASK 0x0f 321 #define QIXIS_LBMAP_SHIFT 0 322 #define QIXIS_LBMAP_DFLTBANK 0x00 323 #define QIXIS_LBMAP_ALTBANK 0x02 324 #define QIXIS_RST_CTL_RESET 0x31 325 #define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 326 #define QIXIS_RCFG_CTL_RECONFIG_START 0x21 327 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 328 329 #define CONFIG_SYS_CSPR3_EXT (0xf) 330 #define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \ 331 | CSPR_PORT_SIZE_8 \ 332 | CSPR_MSEL_GPCM \ 333 | CSPR_V) 334 #define CONFIG_SYS_AMASK3 IFC_AMASK(4 * 1024) 335 #define CONFIG_SYS_CSOR3 0x0 336 /* QIXIS Timing parameters for IFC CS3 */ 337 #define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ 338 FTIM0_GPCM_TEADC(0x0e) | \ 339 FTIM0_GPCM_TEAHC(0x0e)) 340 #define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \ 341 FTIM1_GPCM_TRAD(0x1f)) 342 #define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \ 343 FTIM2_GPCM_TCH(0x8) | \ 344 FTIM2_GPCM_TWP(0x1f)) 345 #define CONFIG_SYS_CS3_FTIM3 0x0 346 347 /* NAND Flash on IFC */ 348 #define CONFIG_NAND_FSL_IFC 349 #define CONFIG_SYS_NAND_MAX_ECCPOS 256 350 #define CONFIG_SYS_NAND_MAX_OOBFREE 2 351 #define CONFIG_SYS_NAND_BASE 0xff800000 352 #ifdef CONFIG_PHYS_64BIT 353 #define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE) 354 #else 355 #define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE 356 #endif 357 358 #define CONFIG_SYS_NAND_CSPR_EXT (0xf) 359 #define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 360 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ 361 | CSPR_MSEL_NAND /* MSEL = NAND */ \ 362 | CSPR_V) 363 #define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024) 364 365 #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ 366 | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ 367 | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ 368 | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \ 369 | CSOR_NAND_PGS_2K /* Page Size = 2K */ \ 370 | CSOR_NAND_SPRZ_64/* Spare size = 64 */ \ 371 | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ 372 373 #define CONFIG_SYS_NAND_ONFI_DETECTION 374 375 /* ONFI NAND Flash mode0 Timing Params */ 376 #define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ 377 FTIM0_NAND_TWP(0x18) | \ 378 FTIM0_NAND_TWCHT(0x07) | \ 379 FTIM0_NAND_TWH(0x0a)) 380 #define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ 381 FTIM1_NAND_TWBE(0x39) | \ 382 FTIM1_NAND_TRR(0x0e) | \ 383 FTIM1_NAND_TRP(0x18)) 384 #define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ 385 FTIM2_NAND_TREH(0x0a) | \ 386 FTIM2_NAND_TWHRE(0x1e)) 387 #define CONFIG_SYS_NAND_FTIM3 0x0 388 389 #define CONFIG_SYS_NAND_DDR_LAW 11 390 391 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } 392 #define CONFIG_SYS_MAX_NAND_DEVICE 1 393 #define CONFIG_CMD_NAND 394 395 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) 396 397 #if defined(CONFIG_NAND) 398 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT 399 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR 400 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK 401 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR 402 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 403 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 404 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 405 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 406 #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR0_CSPR_EXT 407 #define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR0_CSPR 408 #define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK 409 #define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR 410 #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0 411 #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1 412 #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2 413 #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3 414 #else 415 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT 416 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR 417 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK 418 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR 419 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 420 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 421 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 422 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 423 #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT 424 #define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR 425 #define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK 426 #define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR 427 #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0 428 #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1 429 #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2 430 #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3 431 #endif 432 #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR1_CSPR_EXT 433 #define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR 434 #define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK 435 #define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR 436 #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 437 #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 438 #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 439 #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 440 441 #ifdef CONFIG_SPL_BUILD 442 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE 443 #else 444 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 445 #endif 446 447 #if defined(CONFIG_RAMBOOT_PBL) 448 #define CONFIG_SYS_RAMBOOT 449 #endif 450 451 #define CONFIG_BOARD_EARLY_INIT_R 452 #define CONFIG_MISC_INIT_R 453 454 #define CONFIG_HWCONFIG 455 456 /* define to use L1 as initial stack */ 457 #define CONFIG_L1_INIT_RAM 458 #define CONFIG_SYS_INIT_RAM_LOCK 459 #define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ 460 #ifdef CONFIG_PHYS_64BIT 461 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf 462 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe03c000 463 /* The assembler doesn't like typecast */ 464 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ 465 ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ 466 CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) 467 #else 468 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS 0xfe03c000 /* Initial L1 address */ 469 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 470 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS 471 #endif 472 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 473 474 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ 475 GENERATED_GBL_DATA_SIZE) 476 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 477 478 #define CONFIG_SYS_MONITOR_LEN (768 * 1024) 479 #define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) 480 481 /* Serial Port - controlled on board with jumper J8 482 * open - index 2 483 * shorted - index 1 484 */ 485 #define CONFIG_CONS_INDEX 1 486 #define CONFIG_SYS_NS16550 487 #define CONFIG_SYS_NS16550_SERIAL 488 #define CONFIG_SYS_NS16550_REG_SIZE 1 489 #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) 490 491 #define CONFIG_SYS_BAUDRATE_TABLE \ 492 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 493 494 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) 495 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) 496 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) 497 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) 498 #ifndef CONFIG_SPL_BUILD 499 #define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */ 500 #endif 501 502 503 /* Use the HUSH parser */ 504 #define CONFIG_SYS_HUSH_PARSER 505 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " 506 507 /* pass open firmware flat tree */ 508 #define CONFIG_OF_LIBFDT 509 #define CONFIG_OF_BOARD_SETUP 510 #define CONFIG_OF_STDOUT_VIA_ALIAS 511 512 /* new uImage format support */ 513 #define CONFIG_FIT 514 #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ 515 516 /* I2C */ 517 #define CONFIG_SYS_I2C 518 #define CONFIG_SYS_I2C_FSL /* Use FSL common I2C driver */ 519 #define CONFIG_SYS_FSL_I2C_SPEED 400000 /* I2C speed in Hz */ 520 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 521 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 /* I2C speed in Hz */ 522 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 523 #define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 524 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x119000 525 526 /* 527 * RTC configuration 528 */ 529 #define RTC 530 #define CONFIG_RTC_DS3231 1 531 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 532 533 /* 534 * RapidIO 535 */ 536 #ifdef CONFIG_SYS_SRIO 537 #ifdef CONFIG_SRIO1 538 #define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000 539 #ifdef CONFIG_PHYS_64BIT 540 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull 541 #else 542 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xa0000000 543 #endif 544 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */ 545 #endif 546 547 #ifdef CONFIG_SRIO2 548 #define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000 549 #ifdef CONFIG_PHYS_64BIT 550 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull 551 #else 552 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xb0000000 553 #endif 554 #define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */ 555 #endif 556 #endif 557 558 /* 559 * for slave u-boot IMAGE instored in master memory space, 560 * PHYS must be aligned based on the SIZE 561 */ 562 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull 563 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull 564 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */ 565 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull 566 /* 567 * for slave UCODE and ENV instored in master memory space, 568 * PHYS must be aligned based on the SIZE 569 */ 570 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull 571 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull 572 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ 573 574 /* slave core release by master*/ 575 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 576 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ 577 578 /* 579 * SRIO_PCIE_BOOT - SLAVE 580 */ 581 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 582 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 583 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ 584 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) 585 #endif 586 587 /* 588 * eSPI - Enhanced SPI 589 */ 590 #define CONFIG_FSL_ESPI 591 #define CONFIG_SPI_FLASH_SST 592 #define CONFIG_CMD_SF 593 #define CONFIG_SF_DEFAULT_SPEED 10000000 594 #define CONFIG_SF_DEFAULT_MODE 0 595 596 /* 597 * MAPLE 598 */ 599 #ifdef CONFIG_PHYS_64BIT 600 #define CONFIG_SYS_MAPLE_MEM_PHYS 0xFA0000000ull 601 #else 602 #define CONFIG_SYS_MAPLE_MEM_PHYS 0xA0000000 603 #endif 604 605 /* 606 * General PCI 607 * Memory space is mapped 1-1, but I/O space must start from 0. 608 */ 609 610 /* controller 1, direct to uli, tgtid 3, Base address 20000 */ 611 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 612 #ifdef CONFIG_PHYS_64BIT 613 #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 614 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull 615 #else 616 #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 617 #define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000 618 #endif 619 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 620 #define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 621 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 622 #ifdef CONFIG_PHYS_64BIT 623 #define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull 624 #else 625 #define CONFIG_SYS_PCIE1_IO_PHYS 0xf8000000 626 #endif 627 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 628 629 /* Qman/Bman */ 630 #ifndef CONFIG_NOBQFMAN 631 #define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ 632 #define CONFIG_SYS_BMAN_NUM_PORTALS 25 633 #define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 634 #ifdef CONFIG_PHYS_64BIT 635 #define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull 636 #else 637 #define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE 638 #endif 639 #define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000 640 #define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000 641 #define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000 642 #define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE 643 #define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 644 #define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \ 645 CONFIG_SYS_BMAN_CENA_SIZE) 646 #define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 647 #define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08 648 #define CONFIG_SYS_QMAN_NUM_PORTALS 25 649 #define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000 650 #ifdef CONFIG_PHYS_64BIT 651 #define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull 652 #else 653 #define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE 654 #endif 655 #define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000 656 #define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000 657 #define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000 658 #define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE 659 #define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 660 #define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \ 661 CONFIG_SYS_QMAN_CENA_SIZE) 662 #define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 663 #define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08 664 665 #define CONFIG_SYS_DPAA_FMAN 666 667 #define CONFIG_SYS_DPAA_RMAN 668 669 /* Default address of microcode for the Linux Fman driver */ 670 #if defined(CONFIG_SPIFLASH) 671 /* 672 * env is stored at 0x100000, sector size is 0x10000, ucode is stored after 673 * env, so we got 0x110000. 674 */ 675 #define CONFIG_SYS_QE_FW_IN_SPIFLASH 676 #define CONFIG_SYS_FMAN_FW_ADDR 0x110000 677 #elif defined(CONFIG_SDCARD) 678 /* 679 * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is 680 * about 545KB (1089 blocks), Env is stored after the image, and the env size is 681 * 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130. 682 */ 683 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC 684 #define CONFIG_SYS_FMAN_FW_ADDR (512 * 1130) 685 #elif defined(CONFIG_NAND) 686 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND 687 #define CONFIG_SYS_FMAN_FW_ADDR (13 * CONFIG_SYS_NAND_BLOCK_SIZE) 688 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 689 /* 690 * Slave has no ucode locally, it can fetch this from remote. When implementing 691 * in two corenet boards, slave's ucode could be stored in master's memory 692 * space, the address can be mapped from slave TLB->slave LAW-> 693 * slave SRIO or PCIE outbound window->master inbound window-> 694 * master LAW->the ucode address in master's memory space. 695 */ 696 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE 697 #define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000 698 #else 699 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR 700 #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000 701 #endif 702 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 703 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) 704 #endif /* CONFIG_NOBQFMAN */ 705 706 #ifdef CONFIG_SYS_DPAA_FMAN 707 #define CONFIG_FMAN_ENET 708 #define CONFIG_PHYLIB_10G 709 #define CONFIG_PHY_VITESSE 710 #define CONFIG_PHY_TERANETICS 711 #define SGMII_CARD_PORT1_PHY_ADDR 0x1C 712 #define SGMII_CARD_PORT2_PHY_ADDR 0x10 713 #define SGMII_CARD_PORT3_PHY_ADDR 0x1E 714 #define SGMII_CARD_PORT4_PHY_ADDR 0x11 715 #endif 716 717 #ifdef CONFIG_PCI 718 #define CONFIG_PCI_INDIRECT_BRIDGE 719 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 720 721 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 722 #define CONFIG_DOS_PARTITION 723 #endif /* CONFIG_PCI */ 724 725 #ifdef CONFIG_FMAN_ENET 726 #define CONFIG_SYS_FM1_ONBOARD_PHY1_ADDR 0x10 727 #define CONFIG_SYS_FM1_ONBOARD_PHY2_ADDR 0x11 728 729 /*B4860 QDS AMC2PEX-2S default PHY_ADDR */ 730 #define CONFIG_SYS_FM1_10GEC1_PHY_ADDR 0x7 /*SLOT 1*/ 731 #define CONFIG_SYS_FM1_10GEC2_PHY_ADDR 0x6 /*SLOT 2*/ 732 733 734 #define CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR 0x1c 735 #define CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR 0x1d 736 #define CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR 0x1e 737 #define CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR 0x1f 738 739 #define CONFIG_MII /* MII PHY management */ 740 #define CONFIG_ETHPRIME "FM1@DTSEC1" 741 #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ 742 #endif 743 744 #define CONFIG_SYS_FSL_B4860QDS_XFI_ERR 745 746 /* 747 * Environment 748 */ 749 #define CONFIG_LOADS_ECHO /* echo on for serial download */ 750 #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ 751 752 /* 753 * Command line configuration. 754 */ 755 #define CONFIG_CMD_DATE 756 #define CONFIG_CMD_DHCP 757 #define CONFIG_CMD_EEPROM 758 #define CONFIG_CMD_ERRATA 759 #define CONFIG_CMD_GREPENV 760 #define CONFIG_CMD_IRQ 761 #define CONFIG_CMD_I2C 762 #define CONFIG_CMD_MII 763 #define CONFIG_CMD_PING 764 #define CONFIG_CMD_REGINFO 765 766 #ifdef CONFIG_PCI 767 #define CONFIG_CMD_PCI 768 #endif 769 770 /* Hash command with SHA acceleration supported in hardware */ 771 #ifdef CONFIG_FSL_CAAM 772 #define CONFIG_CMD_HASH 773 #define CONFIG_SHA_HW_ACCEL 774 #endif 775 776 /* 777 * USB 778 */ 779 #define CONFIG_HAS_FSL_DR_USB 780 781 #ifdef CONFIG_HAS_FSL_DR_USB 782 #define CONFIG_USB_EHCI 783 784 #ifdef CONFIG_USB_EHCI 785 #define CONFIG_CMD_USB 786 #define CONFIG_USB_STORAGE 787 #define CONFIG_USB_EHCI_FSL 788 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 789 #define CONFIG_CMD_EXT2 790 #endif 791 #endif 792 793 /* 794 * Miscellaneous configurable options 795 */ 796 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 797 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 798 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 799 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 800 #ifdef CONFIG_CMD_KGDB 801 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 802 #else 803 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 804 #endif 805 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) 806 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 807 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ 808 809 /* 810 * For booting Linux, the board info and command line data 811 * have to be in the first 64 MB of memory, since this is 812 * the maximum mapped by the Linux kernel during initialization. 813 */ 814 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/ 815 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 816 817 #ifdef CONFIG_CMD_KGDB 818 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 819 #endif 820 821 /* 822 * Environment Configuration 823 */ 824 #define CONFIG_ROOTPATH "/opt/nfsroot" 825 #define CONFIG_BOOTFILE "uImage" 826 #define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server*/ 827 828 /* default location for tftp and bootm */ 829 #define CONFIG_LOADADDR 1000000 830 831 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ 832 833 #define CONFIG_BAUDRATE 115200 834 835 #define __USB_PHY_TYPE ulpi 836 837 #ifdef CONFIG_PPC_B4860 838 #define HWCONFIG "hwconfig=fsl_ddr:ctlr_intlv=null," \ 839 "bank_intlv=cs0_cs1;" \ 840 "en_cpc:cpc2;" 841 #else 842 #define HWCONFIG "hwconfig=fsl_ddr:ctlr_intlv=null,bank_intlv=cs0_cs1;" 843 #endif 844 845 #define CONFIG_EXTRA_ENV_SETTINGS \ 846 HWCONFIG \ 847 "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ 848 "netdev=eth0\0" \ 849 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 850 "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ 851 "tftpflash=tftpboot $loadaddr $uboot && " \ 852 "protect off $ubootaddr +$filesize && " \ 853 "erase $ubootaddr +$filesize && " \ 854 "cp.b $loadaddr $ubootaddr $filesize && " \ 855 "protect on $ubootaddr +$filesize && " \ 856 "cmp.b $loadaddr $ubootaddr $filesize\0" \ 857 "consoledev=ttyS0\0" \ 858 "ramdiskaddr=2000000\0" \ 859 "ramdiskfile=b4860qds/ramdisk.uboot\0" \ 860 "fdtaddr=c00000\0" \ 861 "fdtfile=b4860qds/b4860qds.dtb\0" \ 862 "bdev=sda3\0" 863 864 /* For emulation this causes u-boot to jump to the start of the proof point 865 app code automatically */ 866 #define CONFIG_PROOF_POINTS \ 867 "setenv bootargs root=/dev/$bdev rw " \ 868 "console=$consoledev,$baudrate $othbootargs;" \ 869 "cpu 1 release 0x29000000 - - -;" \ 870 "cpu 2 release 0x29000000 - - -;" \ 871 "cpu 3 release 0x29000000 - - -;" \ 872 "cpu 4 release 0x29000000 - - -;" \ 873 "cpu 5 release 0x29000000 - - -;" \ 874 "cpu 6 release 0x29000000 - - -;" \ 875 "cpu 7 release 0x29000000 - - -;" \ 876 "go 0x29000000" 877 878 #define CONFIG_HVBOOT \ 879 "setenv bootargs config-addr=0x60000000; " \ 880 "bootm 0x01000000 - 0x00f00000" 881 882 #define CONFIG_ALU \ 883 "setenv bootargs root=/dev/$bdev rw " \ 884 "console=$consoledev,$baudrate $othbootargs;" \ 885 "cpu 1 release 0x01000000 - - -;" \ 886 "cpu 2 release 0x01000000 - - -;" \ 887 "cpu 3 release 0x01000000 - - -;" \ 888 "cpu 4 release 0x01000000 - - -;" \ 889 "cpu 5 release 0x01000000 - - -;" \ 890 "cpu 6 release 0x01000000 - - -;" \ 891 "cpu 7 release 0x01000000 - - -;" \ 892 "go 0x01000000" 893 894 #define CONFIG_LINUX \ 895 "setenv bootargs root=/dev/ram rw " \ 896 "console=$consoledev,$baudrate $othbootargs;" \ 897 "setenv ramdiskaddr 0x02000000;" \ 898 "setenv fdtaddr 0x00c00000;" \ 899 "setenv loadaddr 0x1000000;" \ 900 "bootm $loadaddr $ramdiskaddr $fdtaddr" 901 902 #define CONFIG_HDBOOT \ 903 "setenv bootargs root=/dev/$bdev rw " \ 904 "console=$consoledev,$baudrate $othbootargs;" \ 905 "tftp $loadaddr $bootfile;" \ 906 "tftp $fdtaddr $fdtfile;" \ 907 "bootm $loadaddr - $fdtaddr" 908 909 #define CONFIG_NFSBOOTCOMMAND \ 910 "setenv bootargs root=/dev/nfs rw " \ 911 "nfsroot=$serverip:$rootpath " \ 912 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 913 "console=$consoledev,$baudrate $othbootargs;" \ 914 "tftp $loadaddr $bootfile;" \ 915 "tftp $fdtaddr $fdtfile;" \ 916 "bootm $loadaddr - $fdtaddr" 917 918 #define CONFIG_RAMBOOTCOMMAND \ 919 "setenv bootargs root=/dev/ram rw " \ 920 "console=$consoledev,$baudrate $othbootargs;" \ 921 "tftp $ramdiskaddr $ramdiskfile;" \ 922 "tftp $loadaddr $bootfile;" \ 923 "tftp $fdtaddr $fdtfile;" \ 924 "bootm $loadaddr $ramdiskaddr $fdtaddr" 925 926 #define CONFIG_BOOTCOMMAND CONFIG_LINUX 927 928 #include <asm/fsl_secure_boot.h> 929 930 #ifdef CONFIG_SECURE_BOOT 931 #define CONFIG_CMD_BLOB 932 #endif 933 934 #endif /* __CONFIG_H */ 935