1 /* 2 * Copyright 2011-2012 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #ifndef __CONFIG_H 8 #define __CONFIG_H 9 10 /* 11 * B4860 QDS board configuration file 12 */ 13 #ifdef CONFIG_RAMBOOT_PBL 14 #define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/freescale/b4860qds/b4_pbi.cfg 15 #define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/b4860qds/b4_rcw.cfg 16 #ifndef CONFIG_NAND 17 #define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE 18 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc 19 #else 20 #define CONFIG_SPL_FLUSH_IMAGE 21 #define CONFIG_SPL_TARGET "u-boot-with-spl.bin" 22 #define CONFIG_SYS_TEXT_BASE 0x00201000 23 #define CONFIG_SPL_TEXT_BASE 0xFFFD8000 24 #define CONFIG_SPL_PAD_TO 0x40000 25 #define CONFIG_SPL_MAX_SIZE 0x28000 26 #define RESET_VECTOR_OFFSET 0x27FFC 27 #define BOOT_PAGE_OFFSET 0x27000 28 #define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10) 29 #define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000 30 #define CONFIG_SYS_NAND_U_BOOT_START 0x00200000 31 #define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10) 32 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" 33 #define CONFIG_SPL_NAND_BOOT 34 #ifdef CONFIG_SPL_BUILD 35 #define CONFIG_SPL_SKIP_RELOCATE 36 #define CONFIG_SPL_COMMON_INIT_DDR 37 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE 38 #endif 39 #endif 40 #endif 41 42 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 43 /* Set 1M boot space */ 44 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) 45 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ 46 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) 47 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc 48 #endif 49 50 /* High Level Configuration Options */ 51 #define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ 52 #define CONFIG_MP /* support multiple processors */ 53 54 #ifndef CONFIG_SYS_TEXT_BASE 55 #define CONFIG_SYS_TEXT_BASE 0xeff40000 56 #endif 57 58 #ifndef CONFIG_RESET_VECTOR_ADDRESS 59 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc 60 #endif 61 62 #define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ 63 #define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS 64 #define CONFIG_PCIE1 /* PCIE controller 1 */ 65 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ 66 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ 67 68 #ifndef CONFIG_ARCH_B4420 69 #define CONFIG_SYS_SRIO 70 #define CONFIG_SRIO1 /* SRIO port 1 */ 71 #define CONFIG_SRIO2 /* SRIO port 2 */ 72 #define CONFIG_SRIO_PCIE_BOOT_MASTER 73 #endif 74 75 /* I2C bus multiplexer */ 76 #define I2C_MUX_PCA_ADDR 0x77 77 78 /* VSC Crossbar switches */ 79 #define CONFIG_VSC_CROSSBAR 80 #define I2C_CH_DEFAULT 0x8 81 #define I2C_CH_VSC3316 0xc 82 #define I2C_CH_VSC3308 0xd 83 84 #define VSC3316_TX_ADDRESS 0x70 85 #define VSC3316_RX_ADDRESS 0x71 86 #define VSC3308_TX_ADDRESS 0x02 87 #define VSC3308_RX_ADDRESS 0x03 88 89 /* IDT clock synthesizers */ 90 #define CONFIG_IDT8T49N222A 91 #define I2C_CH_IDT 0x9 92 93 #define IDT_SERDES1_ADDRESS 0x6E 94 #define IDT_SERDES2_ADDRESS 0x6C 95 96 /* Voltage monitor on channel 2*/ 97 #define I2C_MUX_CH_VOL_MONITOR 0xa 98 #define I2C_VOL_MONITOR_ADDR 0x40 99 #define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2 100 #define I2C_VOL_MONITOR_BUS_V_OVF 0x1 101 #define I2C_VOL_MONITOR_BUS_V_SHIFT 3 102 103 #define CONFIG_ZM7300 104 #define I2C_MUX_CH_DPM 0xa 105 #define I2C_DPM_ADDR 0x28 106 107 #define CONFIG_ENV_OVERWRITE 108 109 #ifndef CONFIG_MTD_NOR_FLASH 110 #if !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) && !defined(CONFIG_RAMBOOT_PBL) 111 #define CONFIG_ENV_IS_NOWHERE 112 #endif 113 #else 114 #define CONFIG_FLASH_CFI_DRIVER 115 #define CONFIG_SYS_FLASH_CFI 116 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 117 #endif 118 119 #if defined(CONFIG_SPIFLASH) 120 #define CONFIG_SYS_EXTRA_ENV_RELOC 121 #define CONFIG_ENV_IS_IN_SPI_FLASH 122 #define CONFIG_ENV_SPI_BUS 0 123 #define CONFIG_ENV_SPI_CS 0 124 #define CONFIG_ENV_SPI_MAX_HZ 10000000 125 #define CONFIG_ENV_SPI_MODE 0 126 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ 127 #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ 128 #define CONFIG_ENV_SECT_SIZE 0x10000 129 #elif defined(CONFIG_SDCARD) 130 #define CONFIG_SYS_EXTRA_ENV_RELOC 131 #define CONFIG_ENV_IS_IN_MMC 132 #define CONFIG_SYS_MMC_ENV_DEV 0 133 #define CONFIG_ENV_SIZE 0x2000 134 #define CONFIG_ENV_OFFSET (512 * 1097) 135 #elif defined(CONFIG_NAND) 136 #define CONFIG_SYS_EXTRA_ENV_RELOC 137 #define CONFIG_ENV_IS_IN_NAND 138 #define CONFIG_ENV_SIZE 0x2000 139 #define CONFIG_ENV_OFFSET (10 * CONFIG_SYS_NAND_BLOCK_SIZE) 140 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 141 #define CONFIG_ENV_IS_IN_REMOTE 142 #define CONFIG_ENV_ADDR 0xffe20000 143 #define CONFIG_ENV_SIZE 0x2000 144 #elif defined(CONFIG_ENV_IS_NOWHERE) 145 #define CONFIG_ENV_SIZE 0x2000 146 #else 147 #define CONFIG_ENV_IS_IN_FLASH 148 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) 149 #define CONFIG_ENV_SIZE 0x2000 150 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 151 #endif 152 153 #ifndef __ASSEMBLY__ 154 unsigned long get_board_sys_clk(void); 155 unsigned long get_board_ddr_clk(void); 156 #endif 157 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk() /* sysclk for MPC85xx */ 158 #define CONFIG_DDR_CLK_FREQ get_board_ddr_clk() 159 160 /* 161 * These can be toggled for performance analysis, otherwise use default. 162 */ 163 #define CONFIG_SYS_CACHE_STASHING 164 #define CONFIG_BTB /* toggle branch predition */ 165 #define CONFIG_DDR_ECC 166 #ifdef CONFIG_DDR_ECC 167 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 168 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 169 #endif 170 171 #define CONFIG_ENABLE_36BIT_PHYS 172 173 #ifdef CONFIG_PHYS_64BIT 174 #define CONFIG_ADDR_MAP 175 #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ 176 #endif 177 178 #if 0 179 #define CONFIG_POST CONFIG_SYS_POST_MEMORY /* test POST memory test */ 180 #endif 181 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 182 #define CONFIG_SYS_MEMTEST_END 0x00400000 183 #define CONFIG_SYS_ALT_MEMTEST 184 #define CONFIG_PANIC_HANG /* do not reset board on panic */ 185 186 /* 187 * Config the L3 Cache as L3 SRAM 188 */ 189 #define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000 190 #define CONFIG_SYS_L3_SIZE 256 << 10 191 #define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024) 192 #ifdef CONFIG_NAND 193 #define CONFIG_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024) 194 #endif 195 #define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 12 * 1024) 196 #define CONFIG_SPL_RELOC_MALLOC_SIZE (30 << 10) 197 #define CONFIG_SPL_RELOC_STACK (CONFIG_SPL_GD_ADDR + 64 * 1024) 198 #define CONFIG_SPL_RELOC_STACK_SIZE (22 << 10) 199 200 #ifdef CONFIG_PHYS_64BIT 201 #define CONFIG_SYS_DCSRBAR 0xf0000000 202 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull 203 #endif 204 205 /* EEPROM */ 206 #define CONFIG_ID_EEPROM 207 #define CONFIG_SYS_I2C_EEPROM_NXID 208 #define CONFIG_SYS_EEPROM_BUS_NUM 0 209 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 210 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 211 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 212 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 213 214 /* 215 * DDR Setup 216 */ 217 #define CONFIG_VERY_BIG_RAM 218 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 219 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 220 221 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 222 #define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) 223 224 #define CONFIG_DDR_SPD 225 #define CONFIG_SYS_DDR_RAW_TIMING 226 #ifndef CONFIG_SPL_BUILD 227 #define CONFIG_FSL_DDR_INTERACTIVE 228 #endif 229 230 #define CONFIG_SYS_SPD_BUS_NUM 0 231 #define SPD_EEPROM_ADDRESS1 0x51 232 #define SPD_EEPROM_ADDRESS2 0x53 233 234 #define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 235 #define CONFIG_SYS_SDRAM_SIZE 2048 /* for fixed parameter use */ 236 237 /* 238 * IFC Definitions 239 */ 240 #define CONFIG_SYS_FLASH_BASE 0xe0000000 241 #ifdef CONFIG_PHYS_64BIT 242 #define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) 243 #else 244 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE 245 #endif 246 247 #define CONFIG_SYS_NOR0_CSPR_EXT (0xf) 248 #define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \ 249 + 0x8000000) | \ 250 CSPR_PORT_SIZE_16 | \ 251 CSPR_MSEL_NOR | \ 252 CSPR_V) 253 #define CONFIG_SYS_NOR1_CSPR_EXT (0xf) 254 #define CONFIG_SYS_NOR1_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ 255 CSPR_PORT_SIZE_16 | \ 256 CSPR_MSEL_NOR | \ 257 CSPR_V) 258 #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128 * 1024 * 1024) 259 /* NOR Flash Timing Params */ 260 #define CONFIG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(4) 261 #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x01) | \ 262 FTIM0_NOR_TEADC(0x04) | \ 263 FTIM0_NOR_TEAHC(0x20)) 264 #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ 265 FTIM1_NOR_TRAD_NOR(0x1A) |\ 266 FTIM1_NOR_TSEQRAD_NOR(0x13)) 267 #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x01) | \ 268 FTIM2_NOR_TCH(0x0E) | \ 269 FTIM2_NOR_TWPH(0x0E) | \ 270 FTIM2_NOR_TWP(0x1c)) 271 #define CONFIG_SYS_NOR_FTIM3 0x0 272 273 #define CONFIG_SYS_FLASH_QUIET_TEST 274 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 275 276 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ 277 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 278 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 279 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 280 281 #define CONFIG_SYS_FLASH_EMPTY_INFO 282 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS \ 283 + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS} 284 285 #define CONFIG_FSL_QIXIS /* use common QIXIS code */ 286 #define CONFIG_FSL_QIXIS_V2 287 #define QIXIS_BASE 0xffdf0000 288 #ifdef CONFIG_PHYS_64BIT 289 #define QIXIS_BASE_PHYS (0xf00000000ull | QIXIS_BASE) 290 #else 291 #define QIXIS_BASE_PHYS QIXIS_BASE 292 #endif 293 #define QIXIS_LBMAP_SWITCH 0x01 294 #define QIXIS_LBMAP_MASK 0x0f 295 #define QIXIS_LBMAP_SHIFT 0 296 #define QIXIS_LBMAP_DFLTBANK 0x00 297 #define QIXIS_LBMAP_ALTBANK 0x02 298 #define QIXIS_RST_CTL_RESET 0x31 299 #define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 300 #define QIXIS_RCFG_CTL_RECONFIG_START 0x21 301 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 302 303 #define CONFIG_SYS_CSPR3_EXT (0xf) 304 #define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \ 305 | CSPR_PORT_SIZE_8 \ 306 | CSPR_MSEL_GPCM \ 307 | CSPR_V) 308 #define CONFIG_SYS_AMASK3 IFC_AMASK(4 * 1024) 309 #define CONFIG_SYS_CSOR3 0x0 310 /* QIXIS Timing parameters for IFC CS3 */ 311 #define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ 312 FTIM0_GPCM_TEADC(0x0e) | \ 313 FTIM0_GPCM_TEAHC(0x0e)) 314 #define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \ 315 FTIM1_GPCM_TRAD(0x1f)) 316 #define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \ 317 FTIM2_GPCM_TCH(0x8) | \ 318 FTIM2_GPCM_TWP(0x1f)) 319 #define CONFIG_SYS_CS3_FTIM3 0x0 320 321 /* NAND Flash on IFC */ 322 #define CONFIG_NAND_FSL_IFC 323 #define CONFIG_SYS_NAND_MAX_ECCPOS 256 324 #define CONFIG_SYS_NAND_MAX_OOBFREE 2 325 #define CONFIG_SYS_NAND_BASE 0xff800000 326 #ifdef CONFIG_PHYS_64BIT 327 #define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE) 328 #else 329 #define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE 330 #endif 331 332 #define CONFIG_SYS_NAND_CSPR_EXT (0xf) 333 #define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 334 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ 335 | CSPR_MSEL_NAND /* MSEL = NAND */ \ 336 | CSPR_V) 337 #define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024) 338 339 #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ 340 | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ 341 | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ 342 | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \ 343 | CSOR_NAND_PGS_2K /* Page Size = 2K */ \ 344 | CSOR_NAND_SPRZ_64/* Spare size = 64 */ \ 345 | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ 346 347 #define CONFIG_SYS_NAND_ONFI_DETECTION 348 349 /* ONFI NAND Flash mode0 Timing Params */ 350 #define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ 351 FTIM0_NAND_TWP(0x18) | \ 352 FTIM0_NAND_TWCHT(0x07) | \ 353 FTIM0_NAND_TWH(0x0a)) 354 #define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ 355 FTIM1_NAND_TWBE(0x39) | \ 356 FTIM1_NAND_TRR(0x0e) | \ 357 FTIM1_NAND_TRP(0x18)) 358 #define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ 359 FTIM2_NAND_TREH(0x0a) | \ 360 FTIM2_NAND_TWHRE(0x1e)) 361 #define CONFIG_SYS_NAND_FTIM3 0x0 362 363 #define CONFIG_SYS_NAND_DDR_LAW 11 364 365 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } 366 #define CONFIG_SYS_MAX_NAND_DEVICE 1 367 #define CONFIG_CMD_NAND 368 369 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) 370 371 #if defined(CONFIG_NAND) 372 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT 373 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR 374 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK 375 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR 376 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 377 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 378 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 379 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 380 #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR0_CSPR_EXT 381 #define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR0_CSPR 382 #define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK 383 #define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR 384 #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0 385 #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1 386 #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2 387 #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3 388 #else 389 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT 390 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR 391 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK 392 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR 393 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 394 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 395 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 396 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 397 #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT 398 #define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR 399 #define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK 400 #define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR 401 #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0 402 #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1 403 #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2 404 #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3 405 #endif 406 #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR1_CSPR_EXT 407 #define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR 408 #define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK 409 #define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR 410 #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 411 #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 412 #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 413 #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 414 415 #ifdef CONFIG_SPL_BUILD 416 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE 417 #else 418 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 419 #endif 420 421 #if defined(CONFIG_RAMBOOT_PBL) 422 #define CONFIG_SYS_RAMBOOT 423 #endif 424 425 #define CONFIG_BOARD_EARLY_INIT_R 426 #define CONFIG_MISC_INIT_R 427 428 #define CONFIG_HWCONFIG 429 430 /* define to use L1 as initial stack */ 431 #define CONFIG_L1_INIT_RAM 432 #define CONFIG_SYS_INIT_RAM_LOCK 433 #define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ 434 #ifdef CONFIG_PHYS_64BIT 435 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf 436 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe03c000 437 /* The assembler doesn't like typecast */ 438 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ 439 ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ 440 CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) 441 #else 442 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS 0xfe03c000 /* Initial L1 address */ 443 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 444 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS 445 #endif 446 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 447 448 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ 449 GENERATED_GBL_DATA_SIZE) 450 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 451 452 #define CONFIG_SYS_MONITOR_LEN (768 * 1024) 453 #define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) 454 455 /* Serial Port - controlled on board with jumper J8 456 * open - index 2 457 * shorted - index 1 458 */ 459 #define CONFIG_CONS_INDEX 1 460 #define CONFIG_SYS_NS16550_SERIAL 461 #define CONFIG_SYS_NS16550_REG_SIZE 1 462 #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) 463 464 #define CONFIG_SYS_BAUDRATE_TABLE \ 465 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 466 467 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) 468 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) 469 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) 470 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) 471 472 /* I2C */ 473 #define CONFIG_SYS_I2C 474 #define CONFIG_SYS_I2C_FSL /* Use FSL common I2C driver */ 475 #define CONFIG_SYS_FSL_I2C_SPEED 400000 /* I2C speed in Hz */ 476 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 477 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 /* I2C speed in Hz */ 478 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 479 #define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 480 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x119000 481 482 /* 483 * RTC configuration 484 */ 485 #define RTC 486 #define CONFIG_RTC_DS3231 1 487 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 488 489 /* 490 * RapidIO 491 */ 492 #ifdef CONFIG_SYS_SRIO 493 #ifdef CONFIG_SRIO1 494 #define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000 495 #ifdef CONFIG_PHYS_64BIT 496 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull 497 #else 498 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xa0000000 499 #endif 500 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */ 501 #endif 502 503 #ifdef CONFIG_SRIO2 504 #define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000 505 #ifdef CONFIG_PHYS_64BIT 506 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull 507 #else 508 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xb0000000 509 #endif 510 #define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */ 511 #endif 512 #endif 513 514 /* 515 * for slave u-boot IMAGE instored in master memory space, 516 * PHYS must be aligned based on the SIZE 517 */ 518 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull 519 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull 520 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */ 521 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull 522 /* 523 * for slave UCODE and ENV instored in master memory space, 524 * PHYS must be aligned based on the SIZE 525 */ 526 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull 527 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull 528 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ 529 530 /* slave core release by master*/ 531 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 532 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ 533 534 /* 535 * SRIO_PCIE_BOOT - SLAVE 536 */ 537 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 538 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 539 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ 540 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) 541 #endif 542 543 /* 544 * eSPI - Enhanced SPI 545 */ 546 #define CONFIG_SF_DEFAULT_SPEED 10000000 547 #define CONFIG_SF_DEFAULT_MODE 0 548 549 /* 550 * MAPLE 551 */ 552 #ifdef CONFIG_PHYS_64BIT 553 #define CONFIG_SYS_MAPLE_MEM_PHYS 0xFA0000000ull 554 #else 555 #define CONFIG_SYS_MAPLE_MEM_PHYS 0xA0000000 556 #endif 557 558 /* 559 * General PCI 560 * Memory space is mapped 1-1, but I/O space must start from 0. 561 */ 562 563 /* controller 1, direct to uli, tgtid 3, Base address 20000 */ 564 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 565 #ifdef CONFIG_PHYS_64BIT 566 #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 567 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull 568 #else 569 #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 570 #define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000 571 #endif 572 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 573 #define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 574 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 575 #ifdef CONFIG_PHYS_64BIT 576 #define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull 577 #else 578 #define CONFIG_SYS_PCIE1_IO_PHYS 0xf8000000 579 #endif 580 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 581 582 /* Qman/Bman */ 583 #ifndef CONFIG_NOBQFMAN 584 #define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ 585 #define CONFIG_SYS_BMAN_NUM_PORTALS 25 586 #define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 587 #ifdef CONFIG_PHYS_64BIT 588 #define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull 589 #else 590 #define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE 591 #endif 592 #define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000 593 #define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000 594 #define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000 595 #define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE 596 #define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 597 #define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \ 598 CONFIG_SYS_BMAN_CENA_SIZE) 599 #define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 600 #define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08 601 #define CONFIG_SYS_QMAN_NUM_PORTALS 25 602 #define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000 603 #ifdef CONFIG_PHYS_64BIT 604 #define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull 605 #else 606 #define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE 607 #endif 608 #define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000 609 #define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000 610 #define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000 611 #define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE 612 #define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 613 #define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \ 614 CONFIG_SYS_QMAN_CENA_SIZE) 615 #define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 616 #define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08 617 618 #define CONFIG_SYS_DPAA_FMAN 619 620 #define CONFIG_SYS_DPAA_RMAN 621 622 /* Default address of microcode for the Linux Fman driver */ 623 #if defined(CONFIG_SPIFLASH) 624 /* 625 * env is stored at 0x100000, sector size is 0x10000, ucode is stored after 626 * env, so we got 0x110000. 627 */ 628 #define CONFIG_SYS_QE_FW_IN_SPIFLASH 629 #define CONFIG_SYS_FMAN_FW_ADDR 0x110000 630 #elif defined(CONFIG_SDCARD) 631 /* 632 * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is 633 * about 545KB (1089 blocks), Env is stored after the image, and the env size is 634 * 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130. 635 */ 636 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC 637 #define CONFIG_SYS_FMAN_FW_ADDR (512 * 1130) 638 #elif defined(CONFIG_NAND) 639 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND 640 #define CONFIG_SYS_FMAN_FW_ADDR (13 * CONFIG_SYS_NAND_BLOCK_SIZE) 641 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 642 /* 643 * Slave has no ucode locally, it can fetch this from remote. When implementing 644 * in two corenet boards, slave's ucode could be stored in master's memory 645 * space, the address can be mapped from slave TLB->slave LAW-> 646 * slave SRIO or PCIE outbound window->master inbound window-> 647 * master LAW->the ucode address in master's memory space. 648 */ 649 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE 650 #define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000 651 #else 652 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR 653 #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000 654 #endif 655 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 656 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) 657 #endif /* CONFIG_NOBQFMAN */ 658 659 #ifdef CONFIG_SYS_DPAA_FMAN 660 #define CONFIG_FMAN_ENET 661 #define CONFIG_PHYLIB_10G 662 #define CONFIG_PHY_VITESSE 663 #define CONFIG_PHY_TERANETICS 664 #define SGMII_CARD_PORT1_PHY_ADDR 0x1C 665 #define SGMII_CARD_PORT2_PHY_ADDR 0x10 666 #define SGMII_CARD_PORT3_PHY_ADDR 0x1E 667 #define SGMII_CARD_PORT4_PHY_ADDR 0x11 668 #endif 669 670 #ifdef CONFIG_PCI 671 #define CONFIG_PCI_INDIRECT_BRIDGE 672 673 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 674 #endif /* CONFIG_PCI */ 675 676 #ifdef CONFIG_FMAN_ENET 677 #define CONFIG_SYS_FM1_ONBOARD_PHY1_ADDR 0x10 678 #define CONFIG_SYS_FM1_ONBOARD_PHY2_ADDR 0x11 679 680 /*B4860 QDS AMC2PEX-2S default PHY_ADDR */ 681 #define CONFIG_SYS_FM1_10GEC1_PHY_ADDR 0x7 /*SLOT 1*/ 682 #define CONFIG_SYS_FM1_10GEC2_PHY_ADDR 0x6 /*SLOT 2*/ 683 684 #define CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR 0x1c 685 #define CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR 0x1d 686 #define CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR 0x1e 687 #define CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR 0x1f 688 689 #define CONFIG_MII /* MII PHY management */ 690 #define CONFIG_ETHPRIME "FM1@DTSEC1" 691 #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ 692 #endif 693 694 #define CONFIG_SYS_FSL_B4860QDS_XFI_ERR 695 696 /* 697 * Environment 698 */ 699 #define CONFIG_LOADS_ECHO /* echo on for serial download */ 700 #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ 701 702 /* 703 * Command line configuration. 704 */ 705 #define CONFIG_CMD_DATE 706 #define CONFIG_CMD_EEPROM 707 #define CONFIG_CMD_ERRATA 708 #define CONFIG_CMD_IRQ 709 #define CONFIG_CMD_REGINFO 710 711 #ifdef CONFIG_PCI 712 #define CONFIG_CMD_PCI 713 #endif 714 715 /* Hash command with SHA acceleration supported in hardware */ 716 #ifdef CONFIG_FSL_CAAM 717 #define CONFIG_CMD_HASH 718 #define CONFIG_SHA_HW_ACCEL 719 #endif 720 721 /* 722 * USB 723 */ 724 #define CONFIG_HAS_FSL_DR_USB 725 726 #ifdef CONFIG_HAS_FSL_DR_USB 727 #define CONFIG_USB_EHCI 728 729 #ifdef CONFIG_USB_EHCI 730 #define CONFIG_USB_EHCI_FSL 731 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 732 #endif 733 #endif 734 735 /* 736 * Miscellaneous configurable options 737 */ 738 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 739 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 740 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 741 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 742 #ifdef CONFIG_CMD_KGDB 743 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 744 #else 745 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 746 #endif 747 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) 748 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 749 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ 750 751 /* 752 * For booting Linux, the board info and command line data 753 * have to be in the first 64 MB of memory, since this is 754 * the maximum mapped by the Linux kernel during initialization. 755 */ 756 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/ 757 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 758 759 #ifdef CONFIG_CMD_KGDB 760 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 761 #endif 762 763 /* 764 * Environment Configuration 765 */ 766 #define CONFIG_ROOTPATH "/opt/nfsroot" 767 #define CONFIG_BOOTFILE "uImage" 768 #define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server*/ 769 770 /* default location for tftp and bootm */ 771 #define CONFIG_LOADADDR 1000000 772 773 #define __USB_PHY_TYPE ulpi 774 775 #ifdef CONFIG_ARCH_B4860 776 #define HWCONFIG "hwconfig=fsl_ddr:ctlr_intlv=null," \ 777 "bank_intlv=cs0_cs1;" \ 778 "en_cpc:cpc2;" 779 #else 780 #define HWCONFIG "hwconfig=fsl_ddr:ctlr_intlv=null,bank_intlv=cs0_cs1;" 781 #endif 782 783 #define CONFIG_EXTRA_ENV_SETTINGS \ 784 HWCONFIG \ 785 "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ 786 "netdev=eth0\0" \ 787 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 788 "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ 789 "tftpflash=tftpboot $loadaddr $uboot && " \ 790 "protect off $ubootaddr +$filesize && " \ 791 "erase $ubootaddr +$filesize && " \ 792 "cp.b $loadaddr $ubootaddr $filesize && " \ 793 "protect on $ubootaddr +$filesize && " \ 794 "cmp.b $loadaddr $ubootaddr $filesize\0" \ 795 "consoledev=ttyS0\0" \ 796 "ramdiskaddr=2000000\0" \ 797 "ramdiskfile=b4860qds/ramdisk.uboot\0" \ 798 "fdtaddr=1e00000\0" \ 799 "fdtfile=b4860qds/b4860qds.dtb\0" \ 800 "bdev=sda3\0" 801 802 /* For emulation this causes u-boot to jump to the start of the proof point 803 app code automatically */ 804 #define CONFIG_PROOF_POINTS \ 805 "setenv bootargs root=/dev/$bdev rw " \ 806 "console=$consoledev,$baudrate $othbootargs;" \ 807 "cpu 1 release 0x29000000 - - -;" \ 808 "cpu 2 release 0x29000000 - - -;" \ 809 "cpu 3 release 0x29000000 - - -;" \ 810 "cpu 4 release 0x29000000 - - -;" \ 811 "cpu 5 release 0x29000000 - - -;" \ 812 "cpu 6 release 0x29000000 - - -;" \ 813 "cpu 7 release 0x29000000 - - -;" \ 814 "go 0x29000000" 815 816 #define CONFIG_HVBOOT \ 817 "setenv bootargs config-addr=0x60000000; " \ 818 "bootm 0x01000000 - 0x00f00000" 819 820 #define CONFIG_ALU \ 821 "setenv bootargs root=/dev/$bdev rw " \ 822 "console=$consoledev,$baudrate $othbootargs;" \ 823 "cpu 1 release 0x01000000 - - -;" \ 824 "cpu 2 release 0x01000000 - - -;" \ 825 "cpu 3 release 0x01000000 - - -;" \ 826 "cpu 4 release 0x01000000 - - -;" \ 827 "cpu 5 release 0x01000000 - - -;" \ 828 "cpu 6 release 0x01000000 - - -;" \ 829 "cpu 7 release 0x01000000 - - -;" \ 830 "go 0x01000000" 831 832 #define CONFIG_LINUX \ 833 "setenv bootargs root=/dev/ram rw " \ 834 "console=$consoledev,$baudrate $othbootargs;" \ 835 "setenv ramdiskaddr 0x02000000;" \ 836 "setenv fdtaddr 0x01e00000;" \ 837 "setenv loadaddr 0x1000000;" \ 838 "bootm $loadaddr $ramdiskaddr $fdtaddr" 839 840 #define CONFIG_HDBOOT \ 841 "setenv bootargs root=/dev/$bdev rw " \ 842 "console=$consoledev,$baudrate $othbootargs;" \ 843 "tftp $loadaddr $bootfile;" \ 844 "tftp $fdtaddr $fdtfile;" \ 845 "bootm $loadaddr - $fdtaddr" 846 847 #define CONFIG_NFSBOOTCOMMAND \ 848 "setenv bootargs root=/dev/nfs rw " \ 849 "nfsroot=$serverip:$rootpath " \ 850 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 851 "console=$consoledev,$baudrate $othbootargs;" \ 852 "tftp $loadaddr $bootfile;" \ 853 "tftp $fdtaddr $fdtfile;" \ 854 "bootm $loadaddr - $fdtaddr" 855 856 #define CONFIG_RAMBOOTCOMMAND \ 857 "setenv bootargs root=/dev/ram rw " \ 858 "console=$consoledev,$baudrate $othbootargs;" \ 859 "tftp $ramdiskaddr $ramdiskfile;" \ 860 "tftp $loadaddr $bootfile;" \ 861 "tftp $fdtaddr $fdtfile;" \ 862 "bootm $loadaddr $ramdiskaddr $fdtaddr" 863 864 #define CONFIG_BOOTCOMMAND CONFIG_LINUX 865 866 #include <asm/fsl_secure_boot.h> 867 868 #endif /* __CONFIG_H */ 869