1 /* 2 * (C) Copyright 2005 3 * ARM Ltd. 4 * Peter Pearse, <Peter.Pearse@arm.com> 5 * Configuration for ARM Core Modules. 6 * No standalonw port yet available 7 * - this file is included by both integratorap.h & integratorcp.h 8 * 9 * SPDX-License-Identifier: GPL-2.0+ 10 */ 11 12 #ifndef __ARMCOREMODULE_H 13 #define __ARMCOREMODULE_H 14 15 #define CM_BASE 0x10000000 16 17 /* CM registers common to all CMs */ 18 /* Note that observed values after reboot into the ARM Boot Monitor 19 have been used as defaults, rather than the POR values */ 20 #define OS_CTRL 0x0000000C 21 #define CMMASK_REMAP 0x00000005 /* set remap & led */ 22 #define CMMASK_RESET 0x00000008 23 #define OS_LOCK 0x00000014 24 #define CMVAL_LOCK1 0x0000A000 /* locking value */ 25 #define CMVAL_LOCK2 0x0000005F /* locking value */ 26 #define CMVAL_UNLOCK 0x00000000 /* any value != CM_LOCKVAL */ 27 #define OS_SDRAM 0x00000020 28 #define OS_INIT 0x00000024 29 #define CMMASK_MAP_SIMPLE 0xFFFDFFFF /* simple mapping */ 30 #define CMMASK_TCRAM_DISABLE 0xFFFEFFFF /* TCRAM disabled */ 31 #define CMMASK_LOWVEC 0x00000000 /* vectors @ 0x00000000 */ 32 #define CMMASK_LE 0xFFFFFFF7 /* little endian */ 33 #define CMMASK_CMxx6_COMMON 0x00000013 /* Common value for CMxx6 */ 34 /* - observed reset value of */ 35 /* CM926EJ-S */ 36 /* CM1136-EJ-S */ 37 38 #if defined (CONFIG_CM10200E) || defined (CONFIG_CM10220E) 39 #define CMMASK_INIT_102 0x00000300 /* see CM102xx ref manual */ 40 /* - PLL test clock bypassed */ 41 /* - bus clock ratio 2 */ 42 /* - little endian */ 43 /* - vectors at zero */ 44 #endif /* CM1022xx */ 45 46 /* Determine CM characteristics */ 47 48 #undef CONFIG_CM_MULTIPLE_SSRAM 49 #undef CONFIG_CM_SPD_DETECT 50 #undef CONFIG_CM_REMAP 51 #undef CONFIG_CM_INIT 52 #undef CONFIG_CM_TCRAM 53 54 #if defined (CONFIG_CM946E_S) || defined (CONFIG_CM966E_S) 55 #define CONFIG_CM_MULTIPLE_SSRAM /* CM has multiple SSRAM mapping */ 56 #endif 57 58 /* Excalibur core module has reduced functionality */ 59 #ifndef CONFIG_CM922T_XA10 60 #define CONFIG_CM_SPD_DETECT /* CM supports SPD query */ 61 #define OS_SPD 0x00000100 /* Address of SPD data */ 62 #define CONFIG_CM_REMAP /* CM supports remapping */ 63 #define CONFIG_CM_INIT /* CM has initialization reg */ 64 #endif /* NOT EXCALIBUR */ 65 66 #if defined(CONFIG_CM926EJ_S) || defined (CONFIG_CM946E_S) || \ 67 defined(CONFIG_CM966E_S) || defined (CONFIG_CM1026EJ_S) || \ 68 defined(CONFIG_CM1136JF_S) 69 #define CONFIG_CM_TCRAM /* CM has TCRAM */ 70 #endif 71 72 #ifdef CONFIG_CM_SPD_DETECT 73 #define OS_SPD 0x00000100 /* The SDRAM SPD data is copied here */ 74 #endif 75 76 #endif /* __ARMCOREMODULE_H */ 77