1 /* 2 * MUSB OTG driver peripheral support 3 * 4 * Copyright 2005 Mentor Graphics Corporation 5 * Copyright (C) 2005-2006 by Texas Instruments 6 * Copyright (C) 2006-2007 Nokia Corporation 7 * Copyright (C) 2009 MontaVista Software, Inc. <source@mvista.com> 8 * 9 * This program is free software; you can redistribute it and/or 10 * modify it under the terms of the GNU General Public License 11 * version 2 as published by the Free Software Foundation. 12 * 13 * This program is distributed in the hope that it will be useful, but 14 * WITHOUT ANY WARRANTY; without even the implied warranty of 15 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU 16 * General Public License for more details. 17 * 18 * You should have received a copy of the GNU General Public License 19 * along with this program; if not, write to the Free Software 20 * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 21 * 02110-1301 USA 22 * 23 * THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED 24 * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF 25 * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN 26 * NO EVENT SHALL THE AUTHORS BE LIABLE FOR ANY DIRECT, INDIRECT, 27 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT 28 * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF 29 * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON 30 * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT 31 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF 32 * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 33 * 34 */ 35 36 #ifndef __UBOOT__ 37 #include <linux/kernel.h> 38 #include <linux/list.h> 39 #include <linux/timer.h> 40 #include <linux/module.h> 41 #include <linux/smp.h> 42 #include <linux/spinlock.h> 43 #include <linux/delay.h> 44 #include <linux/dma-mapping.h> 45 #include <linux/slab.h> 46 #else 47 #include <common.h> 48 #include <linux/usb/ch9.h> 49 #include "linux-compat.h" 50 #endif 51 52 #include "musb_core.h" 53 54 55 /* MUSB PERIPHERAL status 3-mar-2006: 56 * 57 * - EP0 seems solid. It passes both USBCV and usbtest control cases. 58 * Minor glitches: 59 * 60 * + remote wakeup to Linux hosts work, but saw USBCV failures; 61 * in one test run (operator error?) 62 * + endpoint halt tests -- in both usbtest and usbcv -- seem 63 * to break when dma is enabled ... is something wrongly 64 * clearing SENDSTALL? 65 * 66 * - Mass storage behaved ok when last tested. Network traffic patterns 67 * (with lots of short transfers etc) need retesting; they turn up the 68 * worst cases of the DMA, since short packets are typical but are not 69 * required. 70 * 71 * - TX/IN 72 * + both pio and dma behave in with network and g_zero tests 73 * + no cppi throughput issues other than no-hw-queueing 74 * + failed with FLAT_REG (DaVinci) 75 * + seems to behave with double buffering, PIO -and- CPPI 76 * + with gadgetfs + AIO, requests got lost? 77 * 78 * - RX/OUT 79 * + both pio and dma behave in with network and g_zero tests 80 * + dma is slow in typical case (short_not_ok is clear) 81 * + double buffering ok with PIO 82 * + double buffering *FAILS* with CPPI, wrong data bytes sometimes 83 * + request lossage observed with gadgetfs 84 * 85 * - ISO not tested ... might work, but only weakly isochronous 86 * 87 * - Gadget driver disabling of softconnect during bind() is ignored; so 88 * drivers can't hold off host requests until userspace is ready. 89 * (Workaround: they can turn it off later.) 90 * 91 * - PORTABILITY (assumes PIO works): 92 * + DaVinci, basically works with cppi dma 93 * + OMAP 2430, ditto with mentor dma 94 * + TUSB 6010, platform-specific dma in the works 95 */ 96 97 /* ----------------------------------------------------------------------- */ 98 99 #define is_buffer_mapped(req) (is_dma_capable() && \ 100 (req->map_state != UN_MAPPED)) 101 102 #ifndef CONFIG_USB_MUSB_PIO_ONLY 103 /* Maps the buffer to dma */ 104 105 static inline void map_dma_buffer(struct musb_request *request, 106 struct musb *musb, struct musb_ep *musb_ep) 107 { 108 int compatible = true; 109 struct dma_controller *dma = musb->dma_controller; 110 111 request->map_state = UN_MAPPED; 112 113 if (!is_dma_capable() || !musb_ep->dma) 114 return; 115 116 /* Check if DMA engine can handle this request. 117 * DMA code must reject the USB request explicitly. 118 * Default behaviour is to map the request. 119 */ 120 if (dma->is_compatible) 121 compatible = dma->is_compatible(musb_ep->dma, 122 musb_ep->packet_sz, request->request.buf, 123 request->request.length); 124 if (!compatible) 125 return; 126 127 if (request->request.dma == DMA_ADDR_INVALID) { 128 request->request.dma = dma_map_single( 129 musb->controller, 130 request->request.buf, 131 request->request.length, 132 request->tx 133 ? DMA_TO_DEVICE 134 : DMA_FROM_DEVICE); 135 request->map_state = MUSB_MAPPED; 136 } else { 137 dma_sync_single_for_device(musb->controller, 138 request->request.dma, 139 request->request.length, 140 request->tx 141 ? DMA_TO_DEVICE 142 : DMA_FROM_DEVICE); 143 request->map_state = PRE_MAPPED; 144 } 145 } 146 147 /* Unmap the buffer from dma and maps it back to cpu */ 148 static inline void unmap_dma_buffer(struct musb_request *request, 149 struct musb *musb) 150 { 151 if (!is_buffer_mapped(request)) 152 return; 153 154 if (request->request.dma == DMA_ADDR_INVALID) { 155 dev_vdbg(musb->controller, 156 "not unmapping a never mapped buffer\n"); 157 return; 158 } 159 if (request->map_state == MUSB_MAPPED) { 160 dma_unmap_single(musb->controller, 161 request->request.dma, 162 request->request.length, 163 request->tx 164 ? DMA_TO_DEVICE 165 : DMA_FROM_DEVICE); 166 request->request.dma = DMA_ADDR_INVALID; 167 } else { /* PRE_MAPPED */ 168 dma_sync_single_for_cpu(musb->controller, 169 request->request.dma, 170 request->request.length, 171 request->tx 172 ? DMA_TO_DEVICE 173 : DMA_FROM_DEVICE); 174 } 175 request->map_state = UN_MAPPED; 176 } 177 #else 178 static inline void map_dma_buffer(struct musb_request *request, 179 struct musb *musb, struct musb_ep *musb_ep) 180 { 181 } 182 183 static inline void unmap_dma_buffer(struct musb_request *request, 184 struct musb *musb) 185 { 186 } 187 #endif 188 189 /* 190 * Immediately complete a request. 191 * 192 * @param request the request to complete 193 * @param status the status to complete the request with 194 * Context: controller locked, IRQs blocked. 195 */ 196 void musb_g_giveback( 197 struct musb_ep *ep, 198 struct usb_request *request, 199 int status) 200 __releases(ep->musb->lock) 201 __acquires(ep->musb->lock) 202 { 203 struct musb_request *req; 204 struct musb *musb; 205 int busy = ep->busy; 206 207 req = to_musb_request(request); 208 209 list_del(&req->list); 210 if (req->request.status == -EINPROGRESS) 211 req->request.status = status; 212 musb = req->musb; 213 214 ep->busy = 1; 215 spin_unlock(&musb->lock); 216 unmap_dma_buffer(req, musb); 217 if (request->status == 0) 218 dev_dbg(musb->controller, "%s done request %p, %d/%d\n", 219 ep->end_point.name, request, 220 req->request.actual, req->request.length); 221 else 222 dev_dbg(musb->controller, "%s request %p, %d/%d fault %d\n", 223 ep->end_point.name, request, 224 req->request.actual, req->request.length, 225 request->status); 226 req->request.complete(&req->ep->end_point, &req->request); 227 spin_lock(&musb->lock); 228 ep->busy = busy; 229 } 230 231 /* ----------------------------------------------------------------------- */ 232 233 /* 234 * Abort requests queued to an endpoint using the status. Synchronous. 235 * caller locked controller and blocked irqs, and selected this ep. 236 */ 237 static void nuke(struct musb_ep *ep, const int status) 238 { 239 struct musb *musb = ep->musb; 240 struct musb_request *req = NULL; 241 void __iomem *epio = ep->musb->endpoints[ep->current_epnum].regs; 242 243 ep->busy = 1; 244 245 if (is_dma_capable() && ep->dma) { 246 struct dma_controller *c = ep->musb->dma_controller; 247 int value; 248 249 if (ep->is_in) { 250 /* 251 * The programming guide says that we must not clear 252 * the DMAMODE bit before DMAENAB, so we only 253 * clear it in the second write... 254 */ 255 musb_writew(epio, MUSB_TXCSR, 256 MUSB_TXCSR_DMAMODE | MUSB_TXCSR_FLUSHFIFO); 257 musb_writew(epio, MUSB_TXCSR, 258 0 | MUSB_TXCSR_FLUSHFIFO); 259 } else { 260 musb_writew(epio, MUSB_RXCSR, 261 0 | MUSB_RXCSR_FLUSHFIFO); 262 musb_writew(epio, MUSB_RXCSR, 263 0 | MUSB_RXCSR_FLUSHFIFO); 264 } 265 266 value = c->channel_abort(ep->dma); 267 dev_dbg(musb->controller, "%s: abort DMA --> %d\n", 268 ep->name, value); 269 c->channel_release(ep->dma); 270 ep->dma = NULL; 271 } 272 273 while (!list_empty(&ep->req_list)) { 274 req = list_first_entry(&ep->req_list, struct musb_request, list); 275 musb_g_giveback(ep, &req->request, status); 276 } 277 } 278 279 /* ----------------------------------------------------------------------- */ 280 281 /* Data transfers - pure PIO, pure DMA, or mixed mode */ 282 283 /* 284 * This assumes the separate CPPI engine is responding to DMA requests 285 * from the usb core ... sequenced a bit differently from mentor dma. 286 */ 287 288 static inline int max_ep_writesize(struct musb *musb, struct musb_ep *ep) 289 { 290 if (can_bulk_split(musb, ep->type)) 291 return ep->hw_ep->max_packet_sz_tx; 292 else 293 return ep->packet_sz; 294 } 295 296 297 #ifdef CONFIG_USB_INVENTRA_DMA 298 299 /* Peripheral tx (IN) using Mentor DMA works as follows: 300 Only mode 0 is used for transfers <= wPktSize, 301 mode 1 is used for larger transfers, 302 303 One of the following happens: 304 - Host sends IN token which causes an endpoint interrupt 305 -> TxAvail 306 -> if DMA is currently busy, exit. 307 -> if queue is non-empty, txstate(). 308 309 - Request is queued by the gadget driver. 310 -> if queue was previously empty, txstate() 311 312 txstate() 313 -> start 314 /\ -> setup DMA 315 | (data is transferred to the FIFO, then sent out when 316 | IN token(s) are recd from Host. 317 | -> DMA interrupt on completion 318 | calls TxAvail. 319 | -> stop DMA, ~DMAENAB, 320 | -> set TxPktRdy for last short pkt or zlp 321 | -> Complete Request 322 | -> Continue next request (call txstate) 323 |___________________________________| 324 325 * Non-Mentor DMA engines can of course work differently, such as by 326 * upleveling from irq-per-packet to irq-per-buffer. 327 */ 328 329 #endif 330 331 /* 332 * An endpoint is transmitting data. This can be called either from 333 * the IRQ routine or from ep.queue() to kickstart a request on an 334 * endpoint. 335 * 336 * Context: controller locked, IRQs blocked, endpoint selected 337 */ 338 static void txstate(struct musb *musb, struct musb_request *req) 339 { 340 u8 epnum = req->epnum; 341 struct musb_ep *musb_ep; 342 void __iomem *epio = musb->endpoints[epnum].regs; 343 struct usb_request *request; 344 u16 fifo_count = 0, csr; 345 int use_dma = 0; 346 347 musb_ep = req->ep; 348 349 /* Check if EP is disabled */ 350 if (!musb_ep->desc) { 351 dev_dbg(musb->controller, "ep:%s disabled - ignore request\n", 352 musb_ep->end_point.name); 353 return; 354 } 355 356 /* we shouldn't get here while DMA is active ... but we do ... */ 357 if (dma_channel_status(musb_ep->dma) == MUSB_DMA_STATUS_BUSY) { 358 dev_dbg(musb->controller, "dma pending...\n"); 359 return; 360 } 361 362 /* read TXCSR before */ 363 csr = musb_readw(epio, MUSB_TXCSR); 364 365 request = &req->request; 366 fifo_count = min(max_ep_writesize(musb, musb_ep), 367 (int)(request->length - request->actual)); 368 369 if (csr & MUSB_TXCSR_TXPKTRDY) { 370 dev_dbg(musb->controller, "%s old packet still ready , txcsr %03x\n", 371 musb_ep->end_point.name, csr); 372 return; 373 } 374 375 if (csr & MUSB_TXCSR_P_SENDSTALL) { 376 dev_dbg(musb->controller, "%s stalling, txcsr %03x\n", 377 musb_ep->end_point.name, csr); 378 return; 379 } 380 381 dev_dbg(musb->controller, "hw_ep%d, maxpacket %d, fifo count %d, txcsr %03x\n", 382 epnum, musb_ep->packet_sz, fifo_count, 383 csr); 384 385 #ifndef CONFIG_USB_MUSB_PIO_ONLY 386 if (is_buffer_mapped(req)) { 387 struct dma_controller *c = musb->dma_controller; 388 size_t request_size; 389 390 /* setup DMA, then program endpoint CSR */ 391 request_size = min_t(size_t, request->length - request->actual, 392 musb_ep->dma->max_len); 393 394 use_dma = (request->dma != DMA_ADDR_INVALID); 395 396 /* MUSB_TXCSR_P_ISO is still set correctly */ 397 398 #if defined(CONFIG_USB_INVENTRA_DMA) || defined(CONFIG_USB_UX500_DMA) 399 { 400 if (request_size < musb_ep->packet_sz) 401 musb_ep->dma->desired_mode = 0; 402 else 403 musb_ep->dma->desired_mode = 1; 404 405 use_dma = use_dma && c->channel_program( 406 musb_ep->dma, musb_ep->packet_sz, 407 musb_ep->dma->desired_mode, 408 request->dma + request->actual, request_size); 409 if (use_dma) { 410 if (musb_ep->dma->desired_mode == 0) { 411 /* 412 * We must not clear the DMAMODE bit 413 * before the DMAENAB bit -- and the 414 * latter doesn't always get cleared 415 * before we get here... 416 */ 417 csr &= ~(MUSB_TXCSR_AUTOSET 418 | MUSB_TXCSR_DMAENAB); 419 musb_writew(epio, MUSB_TXCSR, csr 420 | MUSB_TXCSR_P_WZC_BITS); 421 csr &= ~MUSB_TXCSR_DMAMODE; 422 csr |= (MUSB_TXCSR_DMAENAB | 423 MUSB_TXCSR_MODE); 424 /* against programming guide */ 425 } else { 426 csr |= (MUSB_TXCSR_DMAENAB 427 | MUSB_TXCSR_DMAMODE 428 | MUSB_TXCSR_MODE); 429 if (!musb_ep->hb_mult) 430 csr |= MUSB_TXCSR_AUTOSET; 431 } 432 csr &= ~MUSB_TXCSR_P_UNDERRUN; 433 434 musb_writew(epio, MUSB_TXCSR, csr); 435 } 436 } 437 438 #elif defined(CONFIG_USB_TI_CPPI_DMA) 439 /* program endpoint CSR first, then setup DMA */ 440 csr &= ~(MUSB_TXCSR_P_UNDERRUN | MUSB_TXCSR_TXPKTRDY); 441 csr |= MUSB_TXCSR_DMAENAB | MUSB_TXCSR_DMAMODE | 442 MUSB_TXCSR_MODE; 443 musb_writew(epio, MUSB_TXCSR, 444 (MUSB_TXCSR_P_WZC_BITS & ~MUSB_TXCSR_P_UNDERRUN) 445 | csr); 446 447 /* ensure writebuffer is empty */ 448 csr = musb_readw(epio, MUSB_TXCSR); 449 450 /* NOTE host side sets DMAENAB later than this; both are 451 * OK since the transfer dma glue (between CPPI and Mentor 452 * fifos) just tells CPPI it could start. Data only moves 453 * to the USB TX fifo when both fifos are ready. 454 */ 455 456 /* "mode" is irrelevant here; handle terminating ZLPs like 457 * PIO does, since the hardware RNDIS mode seems unreliable 458 * except for the last-packet-is-already-short case. 459 */ 460 use_dma = use_dma && c->channel_program( 461 musb_ep->dma, musb_ep->packet_sz, 462 0, 463 request->dma + request->actual, 464 request_size); 465 if (!use_dma) { 466 c->channel_release(musb_ep->dma); 467 musb_ep->dma = NULL; 468 csr &= ~MUSB_TXCSR_DMAENAB; 469 musb_writew(epio, MUSB_TXCSR, csr); 470 /* invariant: prequest->buf is non-null */ 471 } 472 #elif defined(CONFIG_USB_TUSB_OMAP_DMA) 473 use_dma = use_dma && c->channel_program( 474 musb_ep->dma, musb_ep->packet_sz, 475 request->zero, 476 request->dma + request->actual, 477 request_size); 478 #endif 479 } 480 #endif 481 482 if (!use_dma) { 483 /* 484 * Unmap the dma buffer back to cpu if dma channel 485 * programming fails 486 */ 487 unmap_dma_buffer(req, musb); 488 489 musb_write_fifo(musb_ep->hw_ep, fifo_count, 490 (u8 *) (request->buf + request->actual)); 491 request->actual += fifo_count; 492 csr |= MUSB_TXCSR_TXPKTRDY; 493 csr &= ~MUSB_TXCSR_P_UNDERRUN; 494 musb_writew(epio, MUSB_TXCSR, csr); 495 } 496 497 /* host may already have the data when this message shows... */ 498 dev_dbg(musb->controller, "%s TX/IN %s len %d/%d, txcsr %04x, fifo %d/%d\n", 499 musb_ep->end_point.name, use_dma ? "dma" : "pio", 500 request->actual, request->length, 501 musb_readw(epio, MUSB_TXCSR), 502 fifo_count, 503 musb_readw(epio, MUSB_TXMAXP)); 504 } 505 506 /* 507 * FIFO state update (e.g. data ready). 508 * Called from IRQ, with controller locked. 509 */ 510 void musb_g_tx(struct musb *musb, u8 epnum) 511 { 512 u16 csr; 513 struct musb_request *req; 514 struct usb_request *request; 515 u8 __iomem *mbase = musb->mregs; 516 struct musb_ep *musb_ep = &musb->endpoints[epnum].ep_in; 517 void __iomem *epio = musb->endpoints[epnum].regs; 518 struct dma_channel *dma; 519 520 musb_ep_select(mbase, epnum); 521 req = next_request(musb_ep); 522 request = &req->request; 523 524 csr = musb_readw(epio, MUSB_TXCSR); 525 dev_dbg(musb->controller, "<== %s, txcsr %04x\n", musb_ep->end_point.name, csr); 526 527 dma = is_dma_capable() ? musb_ep->dma : NULL; 528 529 /* 530 * REVISIT: for high bandwidth, MUSB_TXCSR_P_INCOMPTX 531 * probably rates reporting as a host error. 532 */ 533 if (csr & MUSB_TXCSR_P_SENTSTALL) { 534 csr |= MUSB_TXCSR_P_WZC_BITS; 535 csr &= ~MUSB_TXCSR_P_SENTSTALL; 536 musb_writew(epio, MUSB_TXCSR, csr); 537 return; 538 } 539 540 if (csr & MUSB_TXCSR_P_UNDERRUN) { 541 /* We NAKed, no big deal... little reason to care. */ 542 csr |= MUSB_TXCSR_P_WZC_BITS; 543 csr &= ~(MUSB_TXCSR_P_UNDERRUN | MUSB_TXCSR_TXPKTRDY); 544 musb_writew(epio, MUSB_TXCSR, csr); 545 dev_vdbg(musb->controller, "underrun on ep%d, req %p\n", 546 epnum, request); 547 } 548 549 if (dma_channel_status(dma) == MUSB_DMA_STATUS_BUSY) { 550 /* 551 * SHOULD NOT HAPPEN... has with CPPI though, after 552 * changing SENDSTALL (and other cases); harmless? 553 */ 554 dev_dbg(musb->controller, "%s dma still busy?\n", musb_ep->end_point.name); 555 return; 556 } 557 558 if (request) { 559 u8 is_dma = 0; 560 561 if (dma && (csr & MUSB_TXCSR_DMAENAB)) { 562 is_dma = 1; 563 csr |= MUSB_TXCSR_P_WZC_BITS; 564 csr &= ~(MUSB_TXCSR_DMAENAB | MUSB_TXCSR_P_UNDERRUN | 565 MUSB_TXCSR_TXPKTRDY | MUSB_TXCSR_AUTOSET); 566 musb_writew(epio, MUSB_TXCSR, csr); 567 /* Ensure writebuffer is empty. */ 568 csr = musb_readw(epio, MUSB_TXCSR); 569 request->actual += musb_ep->dma->actual_len; 570 dev_dbg(musb->controller, "TXCSR%d %04x, DMA off, len %zu, req %p\n", 571 epnum, csr, musb_ep->dma->actual_len, request); 572 } 573 574 /* 575 * First, maybe a terminating short packet. Some DMA 576 * engines might handle this by themselves. 577 */ 578 if ((request->zero && request->length 579 && (request->length % musb_ep->packet_sz == 0) 580 && (request->actual == request->length)) 581 #if defined(CONFIG_USB_INVENTRA_DMA) || defined(CONFIG_USB_UX500_DMA) 582 || (is_dma && (!dma->desired_mode || 583 (request->actual & 584 (musb_ep->packet_sz - 1)))) 585 #endif 586 ) { 587 /* 588 * On DMA completion, FIFO may not be 589 * available yet... 590 */ 591 if (csr & MUSB_TXCSR_TXPKTRDY) 592 return; 593 594 dev_dbg(musb->controller, "sending zero pkt\n"); 595 musb_writew(epio, MUSB_TXCSR, MUSB_TXCSR_MODE 596 | MUSB_TXCSR_TXPKTRDY); 597 request->zero = 0; 598 } 599 600 if (request->actual == request->length) { 601 musb_g_giveback(musb_ep, request, 0); 602 /* 603 * In the giveback function the MUSB lock is 604 * released and acquired after sometime. During 605 * this time period the INDEX register could get 606 * changed by the gadget_queue function especially 607 * on SMP systems. Reselect the INDEX to be sure 608 * we are reading/modifying the right registers 609 */ 610 musb_ep_select(mbase, epnum); 611 req = musb_ep->desc ? next_request(musb_ep) : NULL; 612 if (!req) { 613 dev_dbg(musb->controller, "%s idle now\n", 614 musb_ep->end_point.name); 615 return; 616 } 617 } 618 619 txstate(musb, req); 620 } 621 } 622 623 /* ------------------------------------------------------------ */ 624 625 #ifdef CONFIG_USB_INVENTRA_DMA 626 627 /* Peripheral rx (OUT) using Mentor DMA works as follows: 628 - Only mode 0 is used. 629 630 - Request is queued by the gadget class driver. 631 -> if queue was previously empty, rxstate() 632 633 - Host sends OUT token which causes an endpoint interrupt 634 /\ -> RxReady 635 | -> if request queued, call rxstate 636 | /\ -> setup DMA 637 | | -> DMA interrupt on completion 638 | | -> RxReady 639 | | -> stop DMA 640 | | -> ack the read 641 | | -> if data recd = max expected 642 | | by the request, or host 643 | | sent a short packet, 644 | | complete the request, 645 | | and start the next one. 646 | |_____________________________________| 647 | else just wait for the host 648 | to send the next OUT token. 649 |__________________________________________________| 650 651 * Non-Mentor DMA engines can of course work differently. 652 */ 653 654 #endif 655 656 /* 657 * Context: controller locked, IRQs blocked, endpoint selected 658 */ 659 static void rxstate(struct musb *musb, struct musb_request *req) 660 { 661 const u8 epnum = req->epnum; 662 struct usb_request *request = &req->request; 663 struct musb_ep *musb_ep; 664 void __iomem *epio = musb->endpoints[epnum].regs; 665 unsigned fifo_count = 0; 666 u16 len; 667 u16 csr = musb_readw(epio, MUSB_RXCSR); 668 struct musb_hw_ep *hw_ep = &musb->endpoints[epnum]; 669 u8 use_mode_1; 670 671 if (hw_ep->is_shared_fifo) 672 musb_ep = &hw_ep->ep_in; 673 else 674 musb_ep = &hw_ep->ep_out; 675 676 len = musb_ep->packet_sz; 677 678 /* Check if EP is disabled */ 679 if (!musb_ep->desc) { 680 dev_dbg(musb->controller, "ep:%s disabled - ignore request\n", 681 musb_ep->end_point.name); 682 return; 683 } 684 685 /* We shouldn't get here while DMA is active, but we do... */ 686 if (dma_channel_status(musb_ep->dma) == MUSB_DMA_STATUS_BUSY) { 687 dev_dbg(musb->controller, "DMA pending...\n"); 688 return; 689 } 690 691 if (csr & MUSB_RXCSR_P_SENDSTALL) { 692 dev_dbg(musb->controller, "%s stalling, RXCSR %04x\n", 693 musb_ep->end_point.name, csr); 694 return; 695 } 696 697 if (is_cppi_enabled() && is_buffer_mapped(req)) { 698 struct dma_controller *c = musb->dma_controller; 699 struct dma_channel *channel = musb_ep->dma; 700 701 /* NOTE: CPPI won't actually stop advancing the DMA 702 * queue after short packet transfers, so this is almost 703 * always going to run as IRQ-per-packet DMA so that 704 * faults will be handled correctly. 705 */ 706 if (c->channel_program(channel, 707 musb_ep->packet_sz, 708 !request->short_not_ok, 709 request->dma + request->actual, 710 request->length - request->actual)) { 711 712 /* make sure that if an rxpkt arrived after the irq, 713 * the cppi engine will be ready to take it as soon 714 * as DMA is enabled 715 */ 716 csr &= ~(MUSB_RXCSR_AUTOCLEAR 717 | MUSB_RXCSR_DMAMODE); 718 csr |= MUSB_RXCSR_DMAENAB | MUSB_RXCSR_P_WZC_BITS; 719 musb_writew(epio, MUSB_RXCSR, csr); 720 return; 721 } 722 } 723 724 if (csr & MUSB_RXCSR_RXPKTRDY) { 725 len = musb_readw(epio, MUSB_RXCOUNT); 726 727 /* 728 * Enable Mode 1 on RX transfers only when short_not_ok flag 729 * is set. Currently short_not_ok flag is set only from 730 * file_storage and f_mass_storage drivers 731 */ 732 733 if (request->short_not_ok && len == musb_ep->packet_sz) 734 use_mode_1 = 1; 735 else 736 use_mode_1 = 0; 737 738 if (request->actual < request->length) { 739 #ifdef CONFIG_USB_INVENTRA_DMA 740 if (is_buffer_mapped(req)) { 741 struct dma_controller *c; 742 struct dma_channel *channel; 743 int use_dma = 0; 744 745 c = musb->dma_controller; 746 channel = musb_ep->dma; 747 748 /* We use DMA Req mode 0 in rx_csr, and DMA controller operates in 749 * mode 0 only. So we do not get endpoint interrupts due to DMA 750 * completion. We only get interrupts from DMA controller. 751 * 752 * We could operate in DMA mode 1 if we knew the size of the tranfer 753 * in advance. For mass storage class, request->length = what the host 754 * sends, so that'd work. But for pretty much everything else, 755 * request->length is routinely more than what the host sends. For 756 * most these gadgets, end of is signified either by a short packet, 757 * or filling the last byte of the buffer. (Sending extra data in 758 * that last pckate should trigger an overflow fault.) But in mode 1, 759 * we don't get DMA completion interrupt for short packets. 760 * 761 * Theoretically, we could enable DMAReq irq (MUSB_RXCSR_DMAMODE = 1), 762 * to get endpoint interrupt on every DMA req, but that didn't seem 763 * to work reliably. 764 * 765 * REVISIT an updated g_file_storage can set req->short_not_ok, which 766 * then becomes usable as a runtime "use mode 1" hint... 767 */ 768 769 /* Experimental: Mode1 works with mass storage use cases */ 770 if (use_mode_1) { 771 csr |= MUSB_RXCSR_AUTOCLEAR; 772 musb_writew(epio, MUSB_RXCSR, csr); 773 csr |= MUSB_RXCSR_DMAENAB; 774 musb_writew(epio, MUSB_RXCSR, csr); 775 776 /* 777 * this special sequence (enabling and then 778 * disabling MUSB_RXCSR_DMAMODE) is required 779 * to get DMAReq to activate 780 */ 781 musb_writew(epio, MUSB_RXCSR, 782 csr | MUSB_RXCSR_DMAMODE); 783 musb_writew(epio, MUSB_RXCSR, csr); 784 785 } else { 786 if (!musb_ep->hb_mult && 787 musb_ep->hw_ep->rx_double_buffered) 788 csr |= MUSB_RXCSR_AUTOCLEAR; 789 csr |= MUSB_RXCSR_DMAENAB; 790 musb_writew(epio, MUSB_RXCSR, csr); 791 } 792 793 if (request->actual < request->length) { 794 int transfer_size = 0; 795 if (use_mode_1) { 796 transfer_size = min(request->length - request->actual, 797 channel->max_len); 798 musb_ep->dma->desired_mode = 1; 799 } else { 800 transfer_size = min(request->length - request->actual, 801 (unsigned)len); 802 musb_ep->dma->desired_mode = 0; 803 } 804 805 use_dma = c->channel_program( 806 channel, 807 musb_ep->packet_sz, 808 channel->desired_mode, 809 request->dma 810 + request->actual, 811 transfer_size); 812 } 813 814 if (use_dma) 815 return; 816 } 817 #elif defined(CONFIG_USB_UX500_DMA) 818 if ((is_buffer_mapped(req)) && 819 (request->actual < request->length)) { 820 821 struct dma_controller *c; 822 struct dma_channel *channel; 823 int transfer_size = 0; 824 825 c = musb->dma_controller; 826 channel = musb_ep->dma; 827 828 /* In case first packet is short */ 829 if (len < musb_ep->packet_sz) 830 transfer_size = len; 831 else if (request->short_not_ok) 832 transfer_size = min(request->length - 833 request->actual, 834 channel->max_len); 835 else 836 transfer_size = min(request->length - 837 request->actual, 838 (unsigned)len); 839 840 csr &= ~MUSB_RXCSR_DMAMODE; 841 csr |= (MUSB_RXCSR_DMAENAB | 842 MUSB_RXCSR_AUTOCLEAR); 843 844 musb_writew(epio, MUSB_RXCSR, csr); 845 846 if (transfer_size <= musb_ep->packet_sz) { 847 musb_ep->dma->desired_mode = 0; 848 } else { 849 musb_ep->dma->desired_mode = 1; 850 /* Mode must be set after DMAENAB */ 851 csr |= MUSB_RXCSR_DMAMODE; 852 musb_writew(epio, MUSB_RXCSR, csr); 853 } 854 855 if (c->channel_program(channel, 856 musb_ep->packet_sz, 857 channel->desired_mode, 858 request->dma 859 + request->actual, 860 transfer_size)) 861 862 return; 863 } 864 #endif /* Mentor's DMA */ 865 866 fifo_count = request->length - request->actual; 867 dev_dbg(musb->controller, "%s OUT/RX pio fifo %d/%d, maxpacket %d\n", 868 musb_ep->end_point.name, 869 len, fifo_count, 870 musb_ep->packet_sz); 871 872 fifo_count = min_t(unsigned, len, fifo_count); 873 874 #ifdef CONFIG_USB_TUSB_OMAP_DMA 875 if (tusb_dma_omap() && is_buffer_mapped(req)) { 876 struct dma_controller *c = musb->dma_controller; 877 struct dma_channel *channel = musb_ep->dma; 878 u32 dma_addr = request->dma + request->actual; 879 int ret; 880 881 ret = c->channel_program(channel, 882 musb_ep->packet_sz, 883 channel->desired_mode, 884 dma_addr, 885 fifo_count); 886 if (ret) 887 return; 888 } 889 #endif 890 /* 891 * Unmap the dma buffer back to cpu if dma channel 892 * programming fails. This buffer is mapped if the 893 * channel allocation is successful 894 */ 895 if (is_buffer_mapped(req)) { 896 unmap_dma_buffer(req, musb); 897 898 /* 899 * Clear DMAENAB and AUTOCLEAR for the 900 * PIO mode transfer 901 */ 902 csr &= ~(MUSB_RXCSR_DMAENAB | MUSB_RXCSR_AUTOCLEAR); 903 musb_writew(epio, MUSB_RXCSR, csr); 904 } 905 906 musb_read_fifo(musb_ep->hw_ep, fifo_count, (u8 *) 907 (request->buf + request->actual)); 908 request->actual += fifo_count; 909 910 /* REVISIT if we left anything in the fifo, flush 911 * it and report -EOVERFLOW 912 */ 913 914 /* ack the read! */ 915 csr |= MUSB_RXCSR_P_WZC_BITS; 916 csr &= ~MUSB_RXCSR_RXPKTRDY; 917 musb_writew(epio, MUSB_RXCSR, csr); 918 } 919 } 920 921 /* reach the end or short packet detected */ 922 if (request->actual == request->length || len < musb_ep->packet_sz) 923 musb_g_giveback(musb_ep, request, 0); 924 } 925 926 /* 927 * Data ready for a request; called from IRQ 928 */ 929 void musb_g_rx(struct musb *musb, u8 epnum) 930 { 931 u16 csr; 932 struct musb_request *req; 933 struct usb_request *request; 934 void __iomem *mbase = musb->mregs; 935 struct musb_ep *musb_ep; 936 void __iomem *epio = musb->endpoints[epnum].regs; 937 struct dma_channel *dma; 938 struct musb_hw_ep *hw_ep = &musb->endpoints[epnum]; 939 940 if (hw_ep->is_shared_fifo) 941 musb_ep = &hw_ep->ep_in; 942 else 943 musb_ep = &hw_ep->ep_out; 944 945 musb_ep_select(mbase, epnum); 946 947 req = next_request(musb_ep); 948 if (!req) 949 return; 950 951 request = &req->request; 952 953 csr = musb_readw(epio, MUSB_RXCSR); 954 dma = is_dma_capable() ? musb_ep->dma : NULL; 955 956 dev_dbg(musb->controller, "<== %s, rxcsr %04x%s %p\n", musb_ep->end_point.name, 957 csr, dma ? " (dma)" : "", request); 958 959 if (csr & MUSB_RXCSR_P_SENTSTALL) { 960 csr |= MUSB_RXCSR_P_WZC_BITS; 961 csr &= ~MUSB_RXCSR_P_SENTSTALL; 962 musb_writew(epio, MUSB_RXCSR, csr); 963 return; 964 } 965 966 if (csr & MUSB_RXCSR_P_OVERRUN) { 967 /* csr |= MUSB_RXCSR_P_WZC_BITS; */ 968 csr &= ~MUSB_RXCSR_P_OVERRUN; 969 musb_writew(epio, MUSB_RXCSR, csr); 970 971 dev_dbg(musb->controller, "%s iso overrun on %p\n", musb_ep->name, request); 972 if (request->status == -EINPROGRESS) 973 request->status = -EOVERFLOW; 974 } 975 if (csr & MUSB_RXCSR_INCOMPRX) { 976 /* REVISIT not necessarily an error */ 977 dev_dbg(musb->controller, "%s, incomprx\n", musb_ep->end_point.name); 978 } 979 980 if (dma_channel_status(dma) == MUSB_DMA_STATUS_BUSY) { 981 /* "should not happen"; likely RXPKTRDY pending for DMA */ 982 dev_dbg(musb->controller, "%s busy, csr %04x\n", 983 musb_ep->end_point.name, csr); 984 return; 985 } 986 987 if (dma && (csr & MUSB_RXCSR_DMAENAB)) { 988 csr &= ~(MUSB_RXCSR_AUTOCLEAR 989 | MUSB_RXCSR_DMAENAB 990 | MUSB_RXCSR_DMAMODE); 991 musb_writew(epio, MUSB_RXCSR, 992 MUSB_RXCSR_P_WZC_BITS | csr); 993 994 request->actual += musb_ep->dma->actual_len; 995 996 dev_dbg(musb->controller, "RXCSR%d %04x, dma off, %04x, len %zu, req %p\n", 997 epnum, csr, 998 musb_readw(epio, MUSB_RXCSR), 999 musb_ep->dma->actual_len, request); 1000 1001 #if defined(CONFIG_USB_INVENTRA_DMA) || defined(CONFIG_USB_TUSB_OMAP_DMA) || \ 1002 defined(CONFIG_USB_UX500_DMA) 1003 /* Autoclear doesn't clear RxPktRdy for short packets */ 1004 if ((dma->desired_mode == 0 && !hw_ep->rx_double_buffered) 1005 || (dma->actual_len 1006 & (musb_ep->packet_sz - 1))) { 1007 /* ack the read! */ 1008 csr &= ~MUSB_RXCSR_RXPKTRDY; 1009 musb_writew(epio, MUSB_RXCSR, csr); 1010 } 1011 1012 /* incomplete, and not short? wait for next IN packet */ 1013 if ((request->actual < request->length) 1014 && (musb_ep->dma->actual_len 1015 == musb_ep->packet_sz)) { 1016 /* In double buffer case, continue to unload fifo if 1017 * there is Rx packet in FIFO. 1018 **/ 1019 csr = musb_readw(epio, MUSB_RXCSR); 1020 if ((csr & MUSB_RXCSR_RXPKTRDY) && 1021 hw_ep->rx_double_buffered) 1022 goto exit; 1023 return; 1024 } 1025 #endif 1026 musb_g_giveback(musb_ep, request, 0); 1027 /* 1028 * In the giveback function the MUSB lock is 1029 * released and acquired after sometime. During 1030 * this time period the INDEX register could get 1031 * changed by the gadget_queue function especially 1032 * on SMP systems. Reselect the INDEX to be sure 1033 * we are reading/modifying the right registers 1034 */ 1035 musb_ep_select(mbase, epnum); 1036 1037 req = next_request(musb_ep); 1038 if (!req) 1039 return; 1040 } 1041 #if defined(CONFIG_USB_INVENTRA_DMA) || defined(CONFIG_USB_TUSB_OMAP_DMA) || \ 1042 defined(CONFIG_USB_UX500_DMA) 1043 exit: 1044 #endif 1045 /* Analyze request */ 1046 rxstate(musb, req); 1047 } 1048 1049 /* ------------------------------------------------------------ */ 1050 1051 static int musb_gadget_enable(struct usb_ep *ep, 1052 const struct usb_endpoint_descriptor *desc) 1053 { 1054 unsigned long flags; 1055 struct musb_ep *musb_ep; 1056 struct musb_hw_ep *hw_ep; 1057 void __iomem *regs; 1058 struct musb *musb; 1059 void __iomem *mbase; 1060 u8 epnum; 1061 u16 csr; 1062 unsigned tmp; 1063 int status = -EINVAL; 1064 1065 if (!ep || !desc) 1066 return -EINVAL; 1067 1068 musb_ep = to_musb_ep(ep); 1069 hw_ep = musb_ep->hw_ep; 1070 regs = hw_ep->regs; 1071 musb = musb_ep->musb; 1072 mbase = musb->mregs; 1073 epnum = musb_ep->current_epnum; 1074 1075 spin_lock_irqsave(&musb->lock, flags); 1076 1077 if (musb_ep->desc) { 1078 status = -EBUSY; 1079 goto fail; 1080 } 1081 musb_ep->type = usb_endpoint_type(desc); 1082 1083 /* check direction and (later) maxpacket size against endpoint */ 1084 if (usb_endpoint_num(desc) != epnum) 1085 goto fail; 1086 1087 /* REVISIT this rules out high bandwidth periodic transfers */ 1088 tmp = usb_endpoint_maxp(desc); 1089 if (tmp & ~0x07ff) { 1090 int ok; 1091 1092 if (usb_endpoint_dir_in(desc)) 1093 ok = musb->hb_iso_tx; 1094 else 1095 ok = musb->hb_iso_rx; 1096 1097 if (!ok) { 1098 dev_dbg(musb->controller, "no support for high bandwidth ISO\n"); 1099 goto fail; 1100 } 1101 musb_ep->hb_mult = (tmp >> 11) & 3; 1102 } else { 1103 musb_ep->hb_mult = 0; 1104 } 1105 1106 musb_ep->packet_sz = tmp & 0x7ff; 1107 tmp = musb_ep->packet_sz * (musb_ep->hb_mult + 1); 1108 1109 /* enable the interrupts for the endpoint, set the endpoint 1110 * packet size (or fail), set the mode, clear the fifo 1111 */ 1112 musb_ep_select(mbase, epnum); 1113 if (usb_endpoint_dir_in(desc)) { 1114 u16 int_txe = musb_readw(mbase, MUSB_INTRTXE); 1115 1116 if (hw_ep->is_shared_fifo) 1117 musb_ep->is_in = 1; 1118 if (!musb_ep->is_in) 1119 goto fail; 1120 1121 if (tmp > hw_ep->max_packet_sz_tx) { 1122 dev_dbg(musb->controller, "packet size beyond hardware FIFO size\n"); 1123 goto fail; 1124 } 1125 1126 int_txe |= (1 << epnum); 1127 musb_writew(mbase, MUSB_INTRTXE, int_txe); 1128 1129 /* REVISIT if can_bulk_split(), use by updating "tmp"; 1130 * likewise high bandwidth periodic tx 1131 */ 1132 /* Set TXMAXP with the FIFO size of the endpoint 1133 * to disable double buffering mode. 1134 */ 1135 if (musb->double_buffer_not_ok) 1136 musb_writew(regs, MUSB_TXMAXP, hw_ep->max_packet_sz_tx); 1137 else 1138 musb_writew(regs, MUSB_TXMAXP, musb_ep->packet_sz 1139 | (musb_ep->hb_mult << 11)); 1140 1141 csr = MUSB_TXCSR_MODE | MUSB_TXCSR_CLRDATATOG; 1142 if (musb_readw(regs, MUSB_TXCSR) 1143 & MUSB_TXCSR_FIFONOTEMPTY) 1144 csr |= MUSB_TXCSR_FLUSHFIFO; 1145 if (musb_ep->type == USB_ENDPOINT_XFER_ISOC) 1146 csr |= MUSB_TXCSR_P_ISO; 1147 1148 /* set twice in case of double buffering */ 1149 musb_writew(regs, MUSB_TXCSR, csr); 1150 /* REVISIT may be inappropriate w/o FIFONOTEMPTY ... */ 1151 musb_writew(regs, MUSB_TXCSR, csr); 1152 1153 } else { 1154 u16 int_rxe = musb_readw(mbase, MUSB_INTRRXE); 1155 1156 if (hw_ep->is_shared_fifo) 1157 musb_ep->is_in = 0; 1158 if (musb_ep->is_in) 1159 goto fail; 1160 1161 if (tmp > hw_ep->max_packet_sz_rx) { 1162 dev_dbg(musb->controller, "packet size beyond hardware FIFO size\n"); 1163 goto fail; 1164 } 1165 1166 int_rxe |= (1 << epnum); 1167 musb_writew(mbase, MUSB_INTRRXE, int_rxe); 1168 1169 /* REVISIT if can_bulk_combine() use by updating "tmp" 1170 * likewise high bandwidth periodic rx 1171 */ 1172 /* Set RXMAXP with the FIFO size of the endpoint 1173 * to disable double buffering mode. 1174 */ 1175 if (musb->double_buffer_not_ok) 1176 musb_writew(regs, MUSB_RXMAXP, hw_ep->max_packet_sz_tx); 1177 else 1178 musb_writew(regs, MUSB_RXMAXP, musb_ep->packet_sz 1179 | (musb_ep->hb_mult << 11)); 1180 1181 /* force shared fifo to OUT-only mode */ 1182 if (hw_ep->is_shared_fifo) { 1183 csr = musb_readw(regs, MUSB_TXCSR); 1184 csr &= ~(MUSB_TXCSR_MODE | MUSB_TXCSR_TXPKTRDY); 1185 musb_writew(regs, MUSB_TXCSR, csr); 1186 } 1187 1188 csr = MUSB_RXCSR_FLUSHFIFO | MUSB_RXCSR_CLRDATATOG; 1189 if (musb_ep->type == USB_ENDPOINT_XFER_ISOC) 1190 csr |= MUSB_RXCSR_P_ISO; 1191 else if (musb_ep->type == USB_ENDPOINT_XFER_INT) 1192 csr |= MUSB_RXCSR_DISNYET; 1193 1194 /* set twice in case of double buffering */ 1195 musb_writew(regs, MUSB_RXCSR, csr); 1196 musb_writew(regs, MUSB_RXCSR, csr); 1197 } 1198 1199 /* NOTE: all the I/O code _should_ work fine without DMA, in case 1200 * for some reason you run out of channels here. 1201 */ 1202 if (is_dma_capable() && musb->dma_controller) { 1203 struct dma_controller *c = musb->dma_controller; 1204 1205 musb_ep->dma = c->channel_alloc(c, hw_ep, 1206 (desc->bEndpointAddress & USB_DIR_IN)); 1207 } else 1208 musb_ep->dma = NULL; 1209 1210 musb_ep->desc = desc; 1211 musb_ep->busy = 0; 1212 musb_ep->wedged = 0; 1213 status = 0; 1214 1215 pr_debug("%s periph: enabled %s for %s %s, %smaxpacket %d\n", 1216 musb_driver_name, musb_ep->end_point.name, 1217 ({ char *s; switch (musb_ep->type) { 1218 case USB_ENDPOINT_XFER_BULK: s = "bulk"; break; 1219 case USB_ENDPOINT_XFER_INT: s = "int"; break; 1220 default: s = "iso"; break; 1221 }; s; }), 1222 musb_ep->is_in ? "IN" : "OUT", 1223 musb_ep->dma ? "dma, " : "", 1224 musb_ep->packet_sz); 1225 1226 schedule_work(&musb->irq_work); 1227 1228 fail: 1229 spin_unlock_irqrestore(&musb->lock, flags); 1230 return status; 1231 } 1232 1233 /* 1234 * Disable an endpoint flushing all requests queued. 1235 */ 1236 static int musb_gadget_disable(struct usb_ep *ep) 1237 { 1238 unsigned long flags; 1239 struct musb *musb; 1240 u8 epnum; 1241 struct musb_ep *musb_ep; 1242 void __iomem *epio; 1243 int status = 0; 1244 1245 musb_ep = to_musb_ep(ep); 1246 musb = musb_ep->musb; 1247 epnum = musb_ep->current_epnum; 1248 epio = musb->endpoints[epnum].regs; 1249 1250 spin_lock_irqsave(&musb->lock, flags); 1251 musb_ep_select(musb->mregs, epnum); 1252 1253 /* zero the endpoint sizes */ 1254 if (musb_ep->is_in) { 1255 u16 int_txe = musb_readw(musb->mregs, MUSB_INTRTXE); 1256 int_txe &= ~(1 << epnum); 1257 musb_writew(musb->mregs, MUSB_INTRTXE, int_txe); 1258 musb_writew(epio, MUSB_TXMAXP, 0); 1259 } else { 1260 u16 int_rxe = musb_readw(musb->mregs, MUSB_INTRRXE); 1261 int_rxe &= ~(1 << epnum); 1262 musb_writew(musb->mregs, MUSB_INTRRXE, int_rxe); 1263 musb_writew(epio, MUSB_RXMAXP, 0); 1264 } 1265 1266 musb_ep->desc = NULL; 1267 #ifndef __UBOOT__ 1268 musb_ep->end_point.desc = NULL; 1269 #endif 1270 1271 /* abort all pending DMA and requests */ 1272 nuke(musb_ep, -ESHUTDOWN); 1273 1274 schedule_work(&musb->irq_work); 1275 1276 spin_unlock_irqrestore(&(musb->lock), flags); 1277 1278 dev_dbg(musb->controller, "%s\n", musb_ep->end_point.name); 1279 1280 return status; 1281 } 1282 1283 /* 1284 * Allocate a request for an endpoint. 1285 * Reused by ep0 code. 1286 */ 1287 struct usb_request *musb_alloc_request(struct usb_ep *ep, gfp_t gfp_flags) 1288 { 1289 struct musb_ep *musb_ep = to_musb_ep(ep); 1290 struct musb *musb = musb_ep->musb; 1291 struct musb_request *request = NULL; 1292 1293 request = kzalloc(sizeof *request, gfp_flags); 1294 if (!request) { 1295 dev_dbg(musb->controller, "not enough memory\n"); 1296 return NULL; 1297 } 1298 1299 request->request.dma = DMA_ADDR_INVALID; 1300 request->epnum = musb_ep->current_epnum; 1301 request->ep = musb_ep; 1302 1303 return &request->request; 1304 } 1305 1306 /* 1307 * Free a request 1308 * Reused by ep0 code. 1309 */ 1310 void musb_free_request(struct usb_ep *ep, struct usb_request *req) 1311 { 1312 kfree(to_musb_request(req)); 1313 } 1314 1315 static LIST_HEAD(buffers); 1316 1317 struct free_record { 1318 struct list_head list; 1319 struct device *dev; 1320 unsigned bytes; 1321 dma_addr_t dma; 1322 }; 1323 1324 /* 1325 * Context: controller locked, IRQs blocked. 1326 */ 1327 void musb_ep_restart(struct musb *musb, struct musb_request *req) 1328 { 1329 dev_dbg(musb->controller, "<== %s request %p len %u on hw_ep%d\n", 1330 req->tx ? "TX/IN" : "RX/OUT", 1331 &req->request, req->request.length, req->epnum); 1332 1333 musb_ep_select(musb->mregs, req->epnum); 1334 if (req->tx) 1335 txstate(musb, req); 1336 else 1337 rxstate(musb, req); 1338 } 1339 1340 static int musb_gadget_queue(struct usb_ep *ep, struct usb_request *req, 1341 gfp_t gfp_flags) 1342 { 1343 struct musb_ep *musb_ep; 1344 struct musb_request *request; 1345 struct musb *musb; 1346 int status = 0; 1347 unsigned long lockflags; 1348 1349 if (!ep || !req) 1350 return -EINVAL; 1351 if (!req->buf) 1352 return -ENODATA; 1353 1354 musb_ep = to_musb_ep(ep); 1355 musb = musb_ep->musb; 1356 1357 request = to_musb_request(req); 1358 request->musb = musb; 1359 1360 if (request->ep != musb_ep) 1361 return -EINVAL; 1362 1363 dev_dbg(musb->controller, "<== to %s request=%p\n", ep->name, req); 1364 1365 /* request is mine now... */ 1366 request->request.actual = 0; 1367 request->request.status = -EINPROGRESS; 1368 request->epnum = musb_ep->current_epnum; 1369 request->tx = musb_ep->is_in; 1370 1371 map_dma_buffer(request, musb, musb_ep); 1372 1373 spin_lock_irqsave(&musb->lock, lockflags); 1374 1375 /* don't queue if the ep is down */ 1376 if (!musb_ep->desc) { 1377 dev_dbg(musb->controller, "req %p queued to %s while ep %s\n", 1378 req, ep->name, "disabled"); 1379 status = -ESHUTDOWN; 1380 goto cleanup; 1381 } 1382 1383 /* add request to the list */ 1384 list_add_tail(&request->list, &musb_ep->req_list); 1385 1386 /* it this is the head of the queue, start i/o ... */ 1387 if (!musb_ep->busy && &request->list == musb_ep->req_list.next) 1388 musb_ep_restart(musb, request); 1389 1390 cleanup: 1391 spin_unlock_irqrestore(&musb->lock, lockflags); 1392 return status; 1393 } 1394 1395 static int musb_gadget_dequeue(struct usb_ep *ep, struct usb_request *request) 1396 { 1397 struct musb_ep *musb_ep = to_musb_ep(ep); 1398 struct musb_request *req = to_musb_request(request); 1399 struct musb_request *r; 1400 unsigned long flags; 1401 int status = 0; 1402 struct musb *musb = musb_ep->musb; 1403 1404 if (!ep || !request || to_musb_request(request)->ep != musb_ep) 1405 return -EINVAL; 1406 1407 spin_lock_irqsave(&musb->lock, flags); 1408 1409 list_for_each_entry(r, &musb_ep->req_list, list) { 1410 if (r == req) 1411 break; 1412 } 1413 if (r != req) { 1414 dev_dbg(musb->controller, "request %p not queued to %s\n", request, ep->name); 1415 status = -EINVAL; 1416 goto done; 1417 } 1418 1419 /* if the hardware doesn't have the request, easy ... */ 1420 if (musb_ep->req_list.next != &req->list || musb_ep->busy) 1421 musb_g_giveback(musb_ep, request, -ECONNRESET); 1422 1423 /* ... else abort the dma transfer ... */ 1424 else if (is_dma_capable() && musb_ep->dma) { 1425 struct dma_controller *c = musb->dma_controller; 1426 1427 musb_ep_select(musb->mregs, musb_ep->current_epnum); 1428 if (c->channel_abort) 1429 status = c->channel_abort(musb_ep->dma); 1430 else 1431 status = -EBUSY; 1432 if (status == 0) 1433 musb_g_giveback(musb_ep, request, -ECONNRESET); 1434 } else { 1435 /* NOTE: by sticking to easily tested hardware/driver states, 1436 * we leave counting of in-flight packets imprecise. 1437 */ 1438 musb_g_giveback(musb_ep, request, -ECONNRESET); 1439 } 1440 1441 done: 1442 spin_unlock_irqrestore(&musb->lock, flags); 1443 return status; 1444 } 1445 1446 /* 1447 * Set or clear the halt bit of an endpoint. A halted enpoint won't tx/rx any 1448 * data but will queue requests. 1449 * 1450 * exported to ep0 code 1451 */ 1452 static int musb_gadget_set_halt(struct usb_ep *ep, int value) 1453 { 1454 struct musb_ep *musb_ep = to_musb_ep(ep); 1455 u8 epnum = musb_ep->current_epnum; 1456 struct musb *musb = musb_ep->musb; 1457 void __iomem *epio = musb->endpoints[epnum].regs; 1458 void __iomem *mbase; 1459 unsigned long flags; 1460 u16 csr; 1461 struct musb_request *request; 1462 int status = 0; 1463 1464 if (!ep) 1465 return -EINVAL; 1466 mbase = musb->mregs; 1467 1468 spin_lock_irqsave(&musb->lock, flags); 1469 1470 if ((USB_ENDPOINT_XFER_ISOC == musb_ep->type)) { 1471 status = -EINVAL; 1472 goto done; 1473 } 1474 1475 musb_ep_select(mbase, epnum); 1476 1477 request = next_request(musb_ep); 1478 if (value) { 1479 if (request) { 1480 dev_dbg(musb->controller, "request in progress, cannot halt %s\n", 1481 ep->name); 1482 status = -EAGAIN; 1483 goto done; 1484 } 1485 /* Cannot portably stall with non-empty FIFO */ 1486 if (musb_ep->is_in) { 1487 csr = musb_readw(epio, MUSB_TXCSR); 1488 if (csr & MUSB_TXCSR_FIFONOTEMPTY) { 1489 dev_dbg(musb->controller, "FIFO busy, cannot halt %s\n", ep->name); 1490 status = -EAGAIN; 1491 goto done; 1492 } 1493 } 1494 } else 1495 musb_ep->wedged = 0; 1496 1497 /* set/clear the stall and toggle bits */ 1498 dev_dbg(musb->controller, "%s: %s stall\n", ep->name, value ? "set" : "clear"); 1499 if (musb_ep->is_in) { 1500 csr = musb_readw(epio, MUSB_TXCSR); 1501 csr |= MUSB_TXCSR_P_WZC_BITS 1502 | MUSB_TXCSR_CLRDATATOG; 1503 if (value) 1504 csr |= MUSB_TXCSR_P_SENDSTALL; 1505 else 1506 csr &= ~(MUSB_TXCSR_P_SENDSTALL 1507 | MUSB_TXCSR_P_SENTSTALL); 1508 csr &= ~MUSB_TXCSR_TXPKTRDY; 1509 musb_writew(epio, MUSB_TXCSR, csr); 1510 } else { 1511 csr = musb_readw(epio, MUSB_RXCSR); 1512 csr |= MUSB_RXCSR_P_WZC_BITS 1513 | MUSB_RXCSR_FLUSHFIFO 1514 | MUSB_RXCSR_CLRDATATOG; 1515 if (value) 1516 csr |= MUSB_RXCSR_P_SENDSTALL; 1517 else 1518 csr &= ~(MUSB_RXCSR_P_SENDSTALL 1519 | MUSB_RXCSR_P_SENTSTALL); 1520 musb_writew(epio, MUSB_RXCSR, csr); 1521 } 1522 1523 /* maybe start the first request in the queue */ 1524 if (!musb_ep->busy && !value && request) { 1525 dev_dbg(musb->controller, "restarting the request\n"); 1526 musb_ep_restart(musb, request); 1527 } 1528 1529 done: 1530 spin_unlock_irqrestore(&musb->lock, flags); 1531 return status; 1532 } 1533 1534 #ifndef __UBOOT__ 1535 /* 1536 * Sets the halt feature with the clear requests ignored 1537 */ 1538 static int musb_gadget_set_wedge(struct usb_ep *ep) 1539 { 1540 struct musb_ep *musb_ep = to_musb_ep(ep); 1541 1542 if (!ep) 1543 return -EINVAL; 1544 1545 musb_ep->wedged = 1; 1546 1547 return usb_ep_set_halt(ep); 1548 } 1549 #endif 1550 1551 static int musb_gadget_fifo_status(struct usb_ep *ep) 1552 { 1553 struct musb_ep *musb_ep = to_musb_ep(ep); 1554 void __iomem *epio = musb_ep->hw_ep->regs; 1555 int retval = -EINVAL; 1556 1557 if (musb_ep->desc && !musb_ep->is_in) { 1558 struct musb *musb = musb_ep->musb; 1559 int epnum = musb_ep->current_epnum; 1560 void __iomem *mbase = musb->mregs; 1561 unsigned long flags; 1562 1563 spin_lock_irqsave(&musb->lock, flags); 1564 1565 musb_ep_select(mbase, epnum); 1566 /* FIXME return zero unless RXPKTRDY is set */ 1567 retval = musb_readw(epio, MUSB_RXCOUNT); 1568 1569 spin_unlock_irqrestore(&musb->lock, flags); 1570 } 1571 return retval; 1572 } 1573 1574 static void musb_gadget_fifo_flush(struct usb_ep *ep) 1575 { 1576 struct musb_ep *musb_ep = to_musb_ep(ep); 1577 struct musb *musb = musb_ep->musb; 1578 u8 epnum = musb_ep->current_epnum; 1579 void __iomem *epio = musb->endpoints[epnum].regs; 1580 void __iomem *mbase; 1581 unsigned long flags; 1582 u16 csr, int_txe; 1583 1584 mbase = musb->mregs; 1585 1586 spin_lock_irqsave(&musb->lock, flags); 1587 musb_ep_select(mbase, (u8) epnum); 1588 1589 /* disable interrupts */ 1590 int_txe = musb_readw(mbase, MUSB_INTRTXE); 1591 musb_writew(mbase, MUSB_INTRTXE, int_txe & ~(1 << epnum)); 1592 1593 if (musb_ep->is_in) { 1594 csr = musb_readw(epio, MUSB_TXCSR); 1595 if (csr & MUSB_TXCSR_FIFONOTEMPTY) { 1596 csr |= MUSB_TXCSR_FLUSHFIFO | MUSB_TXCSR_P_WZC_BITS; 1597 /* 1598 * Setting both TXPKTRDY and FLUSHFIFO makes controller 1599 * to interrupt current FIFO loading, but not flushing 1600 * the already loaded ones. 1601 */ 1602 csr &= ~MUSB_TXCSR_TXPKTRDY; 1603 musb_writew(epio, MUSB_TXCSR, csr); 1604 /* REVISIT may be inappropriate w/o FIFONOTEMPTY ... */ 1605 musb_writew(epio, MUSB_TXCSR, csr); 1606 } 1607 } else { 1608 csr = musb_readw(epio, MUSB_RXCSR); 1609 csr |= MUSB_RXCSR_FLUSHFIFO | MUSB_RXCSR_P_WZC_BITS; 1610 musb_writew(epio, MUSB_RXCSR, csr); 1611 musb_writew(epio, MUSB_RXCSR, csr); 1612 } 1613 1614 /* re-enable interrupt */ 1615 musb_writew(mbase, MUSB_INTRTXE, int_txe); 1616 spin_unlock_irqrestore(&musb->lock, flags); 1617 } 1618 1619 static const struct usb_ep_ops musb_ep_ops = { 1620 .enable = musb_gadget_enable, 1621 .disable = musb_gadget_disable, 1622 .alloc_request = musb_alloc_request, 1623 .free_request = musb_free_request, 1624 .queue = musb_gadget_queue, 1625 .dequeue = musb_gadget_dequeue, 1626 .set_halt = musb_gadget_set_halt, 1627 #ifndef __UBOOT__ 1628 .set_wedge = musb_gadget_set_wedge, 1629 #endif 1630 .fifo_status = musb_gadget_fifo_status, 1631 .fifo_flush = musb_gadget_fifo_flush 1632 }; 1633 1634 /* ----------------------------------------------------------------------- */ 1635 1636 static int musb_gadget_get_frame(struct usb_gadget *gadget) 1637 { 1638 struct musb *musb = gadget_to_musb(gadget); 1639 1640 return (int)musb_readw(musb->mregs, MUSB_FRAME); 1641 } 1642 1643 static int musb_gadget_wakeup(struct usb_gadget *gadget) 1644 { 1645 #ifndef __UBOOT__ 1646 struct musb *musb = gadget_to_musb(gadget); 1647 void __iomem *mregs = musb->mregs; 1648 unsigned long flags; 1649 int status = -EINVAL; 1650 u8 power, devctl; 1651 int retries; 1652 1653 spin_lock_irqsave(&musb->lock, flags); 1654 1655 switch (musb->xceiv->state) { 1656 case OTG_STATE_B_PERIPHERAL: 1657 /* NOTE: OTG state machine doesn't include B_SUSPENDED; 1658 * that's part of the standard usb 1.1 state machine, and 1659 * doesn't affect OTG transitions. 1660 */ 1661 if (musb->may_wakeup && musb->is_suspended) 1662 break; 1663 goto done; 1664 case OTG_STATE_B_IDLE: 1665 /* Start SRP ... OTG not required. */ 1666 devctl = musb_readb(mregs, MUSB_DEVCTL); 1667 dev_dbg(musb->controller, "Sending SRP: devctl: %02x\n", devctl); 1668 devctl |= MUSB_DEVCTL_SESSION; 1669 musb_writeb(mregs, MUSB_DEVCTL, devctl); 1670 devctl = musb_readb(mregs, MUSB_DEVCTL); 1671 retries = 100; 1672 while (!(devctl & MUSB_DEVCTL_SESSION)) { 1673 devctl = musb_readb(mregs, MUSB_DEVCTL); 1674 if (retries-- < 1) 1675 break; 1676 } 1677 retries = 10000; 1678 while (devctl & MUSB_DEVCTL_SESSION) { 1679 devctl = musb_readb(mregs, MUSB_DEVCTL); 1680 if (retries-- < 1) 1681 break; 1682 } 1683 1684 spin_unlock_irqrestore(&musb->lock, flags); 1685 otg_start_srp(musb->xceiv->otg); 1686 spin_lock_irqsave(&musb->lock, flags); 1687 1688 /* Block idling for at least 1s */ 1689 musb_platform_try_idle(musb, 1690 jiffies + msecs_to_jiffies(1 * HZ)); 1691 1692 status = 0; 1693 goto done; 1694 default: 1695 dev_dbg(musb->controller, "Unhandled wake: %s\n", 1696 otg_state_string(musb->xceiv->state)); 1697 goto done; 1698 } 1699 1700 status = 0; 1701 1702 power = musb_readb(mregs, MUSB_POWER); 1703 power |= MUSB_POWER_RESUME; 1704 musb_writeb(mregs, MUSB_POWER, power); 1705 dev_dbg(musb->controller, "issue wakeup\n"); 1706 1707 /* FIXME do this next chunk in a timer callback, no udelay */ 1708 mdelay(2); 1709 1710 power = musb_readb(mregs, MUSB_POWER); 1711 power &= ~MUSB_POWER_RESUME; 1712 musb_writeb(mregs, MUSB_POWER, power); 1713 done: 1714 spin_unlock_irqrestore(&musb->lock, flags); 1715 return status; 1716 #else 1717 return 0; 1718 #endif 1719 } 1720 1721 static int 1722 musb_gadget_set_self_powered(struct usb_gadget *gadget, int is_selfpowered) 1723 { 1724 struct musb *musb = gadget_to_musb(gadget); 1725 1726 musb->is_self_powered = !!is_selfpowered; 1727 return 0; 1728 } 1729 1730 static void musb_pullup(struct musb *musb, int is_on) 1731 { 1732 u8 power; 1733 1734 power = musb_readb(musb->mregs, MUSB_POWER); 1735 if (is_on) 1736 power |= MUSB_POWER_SOFTCONN; 1737 else 1738 power &= ~MUSB_POWER_SOFTCONN; 1739 1740 /* FIXME if on, HdrcStart; if off, HdrcStop */ 1741 1742 dev_dbg(musb->controller, "gadget D+ pullup %s\n", 1743 is_on ? "on" : "off"); 1744 musb_writeb(musb->mregs, MUSB_POWER, power); 1745 } 1746 1747 #if 0 1748 static int musb_gadget_vbus_session(struct usb_gadget *gadget, int is_active) 1749 { 1750 dev_dbg(musb->controller, "<= %s =>\n", __func__); 1751 1752 /* 1753 * FIXME iff driver's softconnect flag is set (as it is during probe, 1754 * though that can clear it), just musb_pullup(). 1755 */ 1756 1757 return -EINVAL; 1758 } 1759 #endif 1760 1761 static int musb_gadget_vbus_draw(struct usb_gadget *gadget, unsigned mA) 1762 { 1763 #ifndef __UBOOT__ 1764 struct musb *musb = gadget_to_musb(gadget); 1765 1766 if (!musb->xceiv->set_power) 1767 return -EOPNOTSUPP; 1768 return usb_phy_set_power(musb->xceiv, mA); 1769 #else 1770 return 0; 1771 #endif 1772 } 1773 1774 static int musb_gadget_pullup(struct usb_gadget *gadget, int is_on) 1775 { 1776 struct musb *musb = gadget_to_musb(gadget); 1777 unsigned long flags; 1778 1779 is_on = !!is_on; 1780 1781 pm_runtime_get_sync(musb->controller); 1782 1783 /* NOTE: this assumes we are sensing vbus; we'd rather 1784 * not pullup unless the B-session is active. 1785 */ 1786 spin_lock_irqsave(&musb->lock, flags); 1787 if (is_on != musb->softconnect) { 1788 musb->softconnect = is_on; 1789 musb_pullup(musb, is_on); 1790 } 1791 spin_unlock_irqrestore(&musb->lock, flags); 1792 1793 pm_runtime_put(musb->controller); 1794 1795 return 0; 1796 } 1797 1798 #ifndef __UBOOT__ 1799 static int musb_gadget_start(struct usb_gadget *g, 1800 struct usb_gadget_driver *driver); 1801 static int musb_gadget_stop(struct usb_gadget *g, 1802 struct usb_gadget_driver *driver); 1803 #endif 1804 1805 static const struct usb_gadget_ops musb_gadget_operations = { 1806 .get_frame = musb_gadget_get_frame, 1807 .wakeup = musb_gadget_wakeup, 1808 .set_selfpowered = musb_gadget_set_self_powered, 1809 /* .vbus_session = musb_gadget_vbus_session, */ 1810 .vbus_draw = musb_gadget_vbus_draw, 1811 .pullup = musb_gadget_pullup, 1812 #ifndef __UBOOT__ 1813 .udc_start = musb_gadget_start, 1814 .udc_stop = musb_gadget_stop, 1815 #endif 1816 }; 1817 1818 /* ----------------------------------------------------------------------- */ 1819 1820 /* Registration */ 1821 1822 /* Only this registration code "knows" the rule (from USB standards) 1823 * about there being only one external upstream port. It assumes 1824 * all peripheral ports are external... 1825 */ 1826 1827 #ifndef __UBOOT__ 1828 static void musb_gadget_release(struct device *dev) 1829 { 1830 /* kref_put(WHAT) */ 1831 dev_dbg(dev, "%s\n", __func__); 1832 } 1833 #endif 1834 1835 1836 static void __devinit 1837 init_peripheral_ep(struct musb *musb, struct musb_ep *ep, u8 epnum, int is_in) 1838 { 1839 struct musb_hw_ep *hw_ep = musb->endpoints + epnum; 1840 1841 memset(ep, 0, sizeof *ep); 1842 1843 ep->current_epnum = epnum; 1844 ep->musb = musb; 1845 ep->hw_ep = hw_ep; 1846 ep->is_in = is_in; 1847 1848 INIT_LIST_HEAD(&ep->req_list); 1849 1850 sprintf(ep->name, "ep%d%s", epnum, 1851 (!epnum || hw_ep->is_shared_fifo) ? "" : ( 1852 is_in ? "in" : "out")); 1853 ep->end_point.name = ep->name; 1854 INIT_LIST_HEAD(&ep->end_point.ep_list); 1855 if (!epnum) { 1856 ep->end_point.maxpacket = 64; 1857 ep->end_point.ops = &musb_g_ep0_ops; 1858 musb->g.ep0 = &ep->end_point; 1859 } else { 1860 if (is_in) 1861 ep->end_point.maxpacket = hw_ep->max_packet_sz_tx; 1862 else 1863 ep->end_point.maxpacket = hw_ep->max_packet_sz_rx; 1864 ep->end_point.ops = &musb_ep_ops; 1865 list_add_tail(&ep->end_point.ep_list, &musb->g.ep_list); 1866 } 1867 } 1868 1869 /* 1870 * Initialize the endpoints exposed to peripheral drivers, with backlinks 1871 * to the rest of the driver state. 1872 */ 1873 static inline void __devinit musb_g_init_endpoints(struct musb *musb) 1874 { 1875 u8 epnum; 1876 struct musb_hw_ep *hw_ep; 1877 unsigned count = 0; 1878 1879 /* initialize endpoint list just once */ 1880 INIT_LIST_HEAD(&(musb->g.ep_list)); 1881 1882 for (epnum = 0, hw_ep = musb->endpoints; 1883 epnum < musb->nr_endpoints; 1884 epnum++, hw_ep++) { 1885 if (hw_ep->is_shared_fifo /* || !epnum */) { 1886 init_peripheral_ep(musb, &hw_ep->ep_in, epnum, 0); 1887 count++; 1888 } else { 1889 if (hw_ep->max_packet_sz_tx) { 1890 init_peripheral_ep(musb, &hw_ep->ep_in, 1891 epnum, 1); 1892 count++; 1893 } 1894 if (hw_ep->max_packet_sz_rx) { 1895 init_peripheral_ep(musb, &hw_ep->ep_out, 1896 epnum, 0); 1897 count++; 1898 } 1899 } 1900 } 1901 } 1902 1903 /* called once during driver setup to initialize and link into 1904 * the driver model; memory is zeroed. 1905 */ 1906 int __devinit musb_gadget_setup(struct musb *musb) 1907 { 1908 int status; 1909 1910 /* REVISIT minor race: if (erroneously) setting up two 1911 * musb peripherals at the same time, only the bus lock 1912 * is probably held. 1913 */ 1914 1915 musb->g.ops = &musb_gadget_operations; 1916 #ifndef __UBOOT__ 1917 musb->g.max_speed = USB_SPEED_HIGH; 1918 #endif 1919 musb->g.speed = USB_SPEED_UNKNOWN; 1920 1921 #ifndef __UBOOT__ 1922 /* this "gadget" abstracts/virtualizes the controller */ 1923 dev_set_name(&musb->g.dev, "gadget"); 1924 musb->g.dev.parent = musb->controller; 1925 musb->g.dev.dma_mask = musb->controller->dma_mask; 1926 musb->g.dev.release = musb_gadget_release; 1927 #endif 1928 musb->g.name = musb_driver_name; 1929 1930 #ifndef __UBOOT__ 1931 if (is_otg_enabled(musb)) 1932 musb->g.is_otg = 1; 1933 #endif 1934 1935 musb_g_init_endpoints(musb); 1936 1937 musb->is_active = 0; 1938 musb_platform_try_idle(musb, 0); 1939 1940 #ifndef __UBOOT__ 1941 status = device_register(&musb->g.dev); 1942 if (status != 0) { 1943 put_device(&musb->g.dev); 1944 return status; 1945 } 1946 status = usb_add_gadget_udc(musb->controller, &musb->g); 1947 if (status) 1948 goto err; 1949 #endif 1950 1951 return 0; 1952 #ifndef __UBOOT__ 1953 err: 1954 musb->g.dev.parent = NULL; 1955 device_unregister(&musb->g.dev); 1956 return status; 1957 #endif 1958 } 1959 1960 void musb_gadget_cleanup(struct musb *musb) 1961 { 1962 #ifndef __UBOOT__ 1963 usb_del_gadget_udc(&musb->g); 1964 if (musb->g.dev.parent) 1965 device_unregister(&musb->g.dev); 1966 #endif 1967 } 1968 1969 /* 1970 * Register the gadget driver. Used by gadget drivers when 1971 * registering themselves with the controller. 1972 * 1973 * -EINVAL something went wrong (not driver) 1974 * -EBUSY another gadget is already using the controller 1975 * -ENOMEM no memory to perform the operation 1976 * 1977 * @param driver the gadget driver 1978 * @return <0 if error, 0 if everything is fine 1979 */ 1980 #ifndef __UBOOT__ 1981 static int musb_gadget_start(struct usb_gadget *g, 1982 struct usb_gadget_driver *driver) 1983 #else 1984 int musb_gadget_start(struct usb_gadget *g, 1985 struct usb_gadget_driver *driver) 1986 #endif 1987 { 1988 struct musb *musb = gadget_to_musb(g); 1989 #ifndef __UBOOT__ 1990 struct usb_otg *otg = musb->xceiv->otg; 1991 #endif 1992 unsigned long flags; 1993 int retval = -EINVAL; 1994 1995 #ifndef __UBOOT__ 1996 if (driver->max_speed < USB_SPEED_HIGH) 1997 goto err0; 1998 #endif 1999 2000 pm_runtime_get_sync(musb->controller); 2001 2002 #ifndef __UBOOT__ 2003 dev_dbg(musb->controller, "registering driver %s\n", driver->function); 2004 #endif 2005 2006 musb->softconnect = 0; 2007 musb->gadget_driver = driver; 2008 2009 spin_lock_irqsave(&musb->lock, flags); 2010 musb->is_active = 1; 2011 2012 #ifndef __UBOOT__ 2013 otg_set_peripheral(otg, &musb->g); 2014 musb->xceiv->state = OTG_STATE_B_IDLE; 2015 2016 /* 2017 * FIXME this ignores the softconnect flag. Drivers are 2018 * allowed hold the peripheral inactive until for example 2019 * userspace hooks up printer hardware or DSP codecs, so 2020 * hosts only see fully functional devices. 2021 */ 2022 2023 if (!is_otg_enabled(musb)) 2024 #endif 2025 musb_start(musb); 2026 2027 spin_unlock_irqrestore(&musb->lock, flags); 2028 2029 #ifndef __UBOOT__ 2030 if (is_otg_enabled(musb)) { 2031 struct usb_hcd *hcd = musb_to_hcd(musb); 2032 2033 dev_dbg(musb->controller, "OTG startup...\n"); 2034 2035 /* REVISIT: funcall to other code, which also 2036 * handles power budgeting ... this way also 2037 * ensures HdrcStart is indirectly called. 2038 */ 2039 retval = usb_add_hcd(musb_to_hcd(musb), 0, 0); 2040 if (retval < 0) { 2041 dev_dbg(musb->controller, "add_hcd failed, %d\n", retval); 2042 goto err2; 2043 } 2044 2045 if ((musb->xceiv->last_event == USB_EVENT_ID) 2046 && otg->set_vbus) 2047 otg_set_vbus(otg, 1); 2048 2049 hcd->self.uses_pio_for_control = 1; 2050 } 2051 if (musb->xceiv->last_event == USB_EVENT_NONE) 2052 pm_runtime_put(musb->controller); 2053 #endif 2054 2055 return 0; 2056 2057 #ifndef __UBOOT__ 2058 err2: 2059 if (!is_otg_enabled(musb)) 2060 musb_stop(musb); 2061 err0: 2062 return retval; 2063 #endif 2064 } 2065 2066 #ifndef __UBOOT__ 2067 static void stop_activity(struct musb *musb, struct usb_gadget_driver *driver) 2068 { 2069 int i; 2070 struct musb_hw_ep *hw_ep; 2071 2072 /* don't disconnect if it's not connected */ 2073 if (musb->g.speed == USB_SPEED_UNKNOWN) 2074 driver = NULL; 2075 else 2076 musb->g.speed = USB_SPEED_UNKNOWN; 2077 2078 /* deactivate the hardware */ 2079 if (musb->softconnect) { 2080 musb->softconnect = 0; 2081 musb_pullup(musb, 0); 2082 } 2083 musb_stop(musb); 2084 2085 /* killing any outstanding requests will quiesce the driver; 2086 * then report disconnect 2087 */ 2088 if (driver) { 2089 for (i = 0, hw_ep = musb->endpoints; 2090 i < musb->nr_endpoints; 2091 i++, hw_ep++) { 2092 musb_ep_select(musb->mregs, i); 2093 if (hw_ep->is_shared_fifo /* || !epnum */) { 2094 nuke(&hw_ep->ep_in, -ESHUTDOWN); 2095 } else { 2096 if (hw_ep->max_packet_sz_tx) 2097 nuke(&hw_ep->ep_in, -ESHUTDOWN); 2098 if (hw_ep->max_packet_sz_rx) 2099 nuke(&hw_ep->ep_out, -ESHUTDOWN); 2100 } 2101 } 2102 } 2103 } 2104 2105 /* 2106 * Unregister the gadget driver. Used by gadget drivers when 2107 * unregistering themselves from the controller. 2108 * 2109 * @param driver the gadget driver to unregister 2110 */ 2111 static int musb_gadget_stop(struct usb_gadget *g, 2112 struct usb_gadget_driver *driver) 2113 { 2114 struct musb *musb = gadget_to_musb(g); 2115 unsigned long flags; 2116 2117 if (musb->xceiv->last_event == USB_EVENT_NONE) 2118 pm_runtime_get_sync(musb->controller); 2119 2120 /* 2121 * REVISIT always use otg_set_peripheral() here too; 2122 * this needs to shut down the OTG engine. 2123 */ 2124 2125 spin_lock_irqsave(&musb->lock, flags); 2126 2127 musb_hnp_stop(musb); 2128 2129 (void) musb_gadget_vbus_draw(&musb->g, 0); 2130 2131 musb->xceiv->state = OTG_STATE_UNDEFINED; 2132 stop_activity(musb, driver); 2133 otg_set_peripheral(musb->xceiv->otg, NULL); 2134 2135 dev_dbg(musb->controller, "unregistering driver %s\n", driver->function); 2136 2137 musb->is_active = 0; 2138 musb_platform_try_idle(musb, 0); 2139 spin_unlock_irqrestore(&musb->lock, flags); 2140 2141 if (is_otg_enabled(musb)) { 2142 usb_remove_hcd(musb_to_hcd(musb)); 2143 /* FIXME we need to be able to register another 2144 * gadget driver here and have everything work; 2145 * that currently misbehaves. 2146 */ 2147 } 2148 2149 if (!is_otg_enabled(musb)) 2150 musb_stop(musb); 2151 2152 pm_runtime_put(musb->controller); 2153 2154 return 0; 2155 } 2156 #endif 2157 2158 /* ----------------------------------------------------------------------- */ 2159 2160 /* lifecycle operations called through plat_uds.c */ 2161 2162 void musb_g_resume(struct musb *musb) 2163 { 2164 #ifndef __UBOOT__ 2165 musb->is_suspended = 0; 2166 switch (musb->xceiv->state) { 2167 case OTG_STATE_B_IDLE: 2168 break; 2169 case OTG_STATE_B_WAIT_ACON: 2170 case OTG_STATE_B_PERIPHERAL: 2171 musb->is_active = 1; 2172 if (musb->gadget_driver && musb->gadget_driver->resume) { 2173 spin_unlock(&musb->lock); 2174 musb->gadget_driver->resume(&musb->g); 2175 spin_lock(&musb->lock); 2176 } 2177 break; 2178 default: 2179 WARNING("unhandled RESUME transition (%s)\n", 2180 otg_state_string(musb->xceiv->state)); 2181 } 2182 #endif 2183 } 2184 2185 /* called when SOF packets stop for 3+ msec */ 2186 void musb_g_suspend(struct musb *musb) 2187 { 2188 #ifndef __UBOOT__ 2189 u8 devctl; 2190 2191 devctl = musb_readb(musb->mregs, MUSB_DEVCTL); 2192 dev_dbg(musb->controller, "devctl %02x\n", devctl); 2193 2194 switch (musb->xceiv->state) { 2195 case OTG_STATE_B_IDLE: 2196 if ((devctl & MUSB_DEVCTL_VBUS) == MUSB_DEVCTL_VBUS) 2197 musb->xceiv->state = OTG_STATE_B_PERIPHERAL; 2198 break; 2199 case OTG_STATE_B_PERIPHERAL: 2200 musb->is_suspended = 1; 2201 if (musb->gadget_driver && musb->gadget_driver->suspend) { 2202 spin_unlock(&musb->lock); 2203 musb->gadget_driver->suspend(&musb->g); 2204 spin_lock(&musb->lock); 2205 } 2206 break; 2207 default: 2208 /* REVISIT if B_HOST, clear DEVCTL.HOSTREQ; 2209 * A_PERIPHERAL may need care too 2210 */ 2211 WARNING("unhandled SUSPEND transition (%s)\n", 2212 otg_state_string(musb->xceiv->state)); 2213 } 2214 #endif 2215 } 2216 2217 /* Called during SRP */ 2218 void musb_g_wakeup(struct musb *musb) 2219 { 2220 musb_gadget_wakeup(&musb->g); 2221 } 2222 2223 /* called when VBUS drops below session threshold, and in other cases */ 2224 void musb_g_disconnect(struct musb *musb) 2225 { 2226 void __iomem *mregs = musb->mregs; 2227 u8 devctl = musb_readb(mregs, MUSB_DEVCTL); 2228 2229 dev_dbg(musb->controller, "devctl %02x\n", devctl); 2230 2231 /* clear HR */ 2232 musb_writeb(mregs, MUSB_DEVCTL, devctl & MUSB_DEVCTL_SESSION); 2233 2234 /* don't draw vbus until new b-default session */ 2235 (void) musb_gadget_vbus_draw(&musb->g, 0); 2236 2237 musb->g.speed = USB_SPEED_UNKNOWN; 2238 if (musb->gadget_driver && musb->gadget_driver->disconnect) { 2239 spin_unlock(&musb->lock); 2240 musb->gadget_driver->disconnect(&musb->g); 2241 spin_lock(&musb->lock); 2242 } 2243 2244 #ifndef __UBOOT__ 2245 switch (musb->xceiv->state) { 2246 default: 2247 dev_dbg(musb->controller, "Unhandled disconnect %s, setting a_idle\n", 2248 otg_state_string(musb->xceiv->state)); 2249 musb->xceiv->state = OTG_STATE_A_IDLE; 2250 MUSB_HST_MODE(musb); 2251 break; 2252 case OTG_STATE_A_PERIPHERAL: 2253 musb->xceiv->state = OTG_STATE_A_WAIT_BCON; 2254 MUSB_HST_MODE(musb); 2255 break; 2256 case OTG_STATE_B_WAIT_ACON: 2257 case OTG_STATE_B_HOST: 2258 case OTG_STATE_B_PERIPHERAL: 2259 case OTG_STATE_B_IDLE: 2260 musb->xceiv->state = OTG_STATE_B_IDLE; 2261 break; 2262 case OTG_STATE_B_SRP_INIT: 2263 break; 2264 } 2265 #endif 2266 2267 musb->is_active = 0; 2268 } 2269 2270 void musb_g_reset(struct musb *musb) 2271 __releases(musb->lock) 2272 __acquires(musb->lock) 2273 { 2274 void __iomem *mbase = musb->mregs; 2275 u8 devctl = musb_readb(mbase, MUSB_DEVCTL); 2276 u8 power; 2277 2278 #ifndef __UBOOT__ 2279 dev_dbg(musb->controller, "<== %s addr=%x driver '%s'\n", 2280 (devctl & MUSB_DEVCTL_BDEVICE) 2281 ? "B-Device" : "A-Device", 2282 musb_readb(mbase, MUSB_FADDR), 2283 musb->gadget_driver 2284 ? musb->gadget_driver->driver.name 2285 : NULL 2286 ); 2287 #endif 2288 2289 /* report disconnect, if we didn't already (flushing EP state) */ 2290 if (musb->g.speed != USB_SPEED_UNKNOWN) 2291 musb_g_disconnect(musb); 2292 2293 /* clear HR */ 2294 else if (devctl & MUSB_DEVCTL_HR) 2295 musb_writeb(mbase, MUSB_DEVCTL, MUSB_DEVCTL_SESSION); 2296 2297 2298 /* what speed did we negotiate? */ 2299 power = musb_readb(mbase, MUSB_POWER); 2300 musb->g.speed = (power & MUSB_POWER_HSMODE) 2301 ? USB_SPEED_HIGH : USB_SPEED_FULL; 2302 2303 /* start in USB_STATE_DEFAULT */ 2304 musb->is_active = 1; 2305 musb->is_suspended = 0; 2306 MUSB_DEV_MODE(musb); 2307 musb->address = 0; 2308 musb->ep0_state = MUSB_EP0_STAGE_SETUP; 2309 2310 musb->may_wakeup = 0; 2311 musb->g.b_hnp_enable = 0; 2312 musb->g.a_alt_hnp_support = 0; 2313 musb->g.a_hnp_support = 0; 2314 2315 #ifndef __UBOOT__ 2316 /* Normal reset, as B-Device; 2317 * or else after HNP, as A-Device 2318 */ 2319 if (devctl & MUSB_DEVCTL_BDEVICE) { 2320 musb->xceiv->state = OTG_STATE_B_PERIPHERAL; 2321 musb->g.is_a_peripheral = 0; 2322 } else if (is_otg_enabled(musb)) { 2323 musb->xceiv->state = OTG_STATE_A_PERIPHERAL; 2324 musb->g.is_a_peripheral = 1; 2325 } else 2326 WARN_ON(1); 2327 2328 /* start with default limits on VBUS power draw */ 2329 (void) musb_gadget_vbus_draw(&musb->g, 2330 is_otg_enabled(musb) ? 8 : 100); 2331 #endif 2332 } 2333