1 /* SPDX-License-Identifier: GPL-2.0 */ 2 /* 3 * R8A66597 HCD (Host Controller Driver) for u-boot 4 * 5 * Copyright (C) 2008 Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> 6 */ 7 8 #ifndef __R8A66597_H__ 9 #define __R8A66597_H__ 10 11 #define SYSCFG0 0x00 12 #define SYSCFG1 0x02 13 #define SYSSTS0 0x04 14 #define SYSSTS1 0x06 15 #define DVSTCTR0 0x08 16 #define DVSTCTR1 0x0A 17 #define TESTMODE 0x0C 18 #define PINCFG 0x0E 19 #define DMA0CFG 0x10 20 #define DMA1CFG 0x12 21 #define CFIFO 0x14 22 #define D0FIFO 0x18 23 #define D1FIFO 0x1C 24 #define CFIFOSEL 0x20 25 #define CFIFOCTR 0x22 26 #define CFIFOSIE 0x24 27 #define D0FIFOSEL 0x28 28 #define D0FIFOCTR 0x2A 29 #define D1FIFOSEL 0x2C 30 #define D1FIFOCTR 0x2E 31 #define INTENB0 0x30 32 #define INTENB1 0x32 33 #define INTENB2 0x34 34 #define BRDYENB 0x36 35 #define NRDYENB 0x38 36 #define BEMPENB 0x3A 37 #define SOFCFG 0x3C 38 #define INTSTS0 0x40 39 #define INTSTS1 0x42 40 #define INTSTS2 0x44 41 #define BRDYSTS 0x46 42 #define NRDYSTS 0x48 43 #define BEMPSTS 0x4A 44 #define FRMNUM 0x4C 45 #define UFRMNUM 0x4E 46 #define USBADDR 0x50 47 #define USBREQ 0x54 48 #define USBVAL 0x56 49 #define USBINDX 0x58 50 #define USBLENG 0x5A 51 #define DCPCFG 0x5C 52 #define DCPMAXP 0x5E 53 #define DCPCTR 0x60 54 #define PIPESEL 0x64 55 #define PIPECFG 0x68 56 #define PIPEBUF 0x6A 57 #define PIPEMAXP 0x6C 58 #define PIPEPERI 0x6E 59 #define PIPE1CTR 0x70 60 #define PIPE2CTR 0x72 61 #define PIPE3CTR 0x74 62 #define PIPE4CTR 0x76 63 #define PIPE5CTR 0x78 64 #define PIPE6CTR 0x7A 65 #define PIPE7CTR 0x7C 66 #define PIPE8CTR 0x7E 67 #define PIPE9CTR 0x80 68 #define PIPE1TRE 0x90 69 #define PIPE1TRN 0x92 70 #define PIPE2TRE 0x94 71 #define PIPE2TRN 0x96 72 #define PIPE3TRE 0x98 73 #define PIPE3TRN 0x9A 74 #define PIPE4TRE 0x9C 75 #define PIPE4TRN 0x9E 76 #define PIPE5TRE 0xA0 77 #define PIPE5TRN 0xA2 78 #define DEVADD0 0xD0 79 #define DEVADD1 0xD2 80 #define DEVADD2 0xD4 81 #define DEVADD3 0xD6 82 #define DEVADD4 0xD8 83 #define DEVADD5 0xDA 84 #define DEVADD6 0xDC 85 #define DEVADD7 0xDE 86 #define DEVADD8 0xE0 87 #define DEVADD9 0xE2 88 #define DEVADDA 0xE4 89 #define SUSPMODE0 0x102 /* RZ/A only */ 90 91 /* System Configuration Control Register */ 92 #if !defined(CONFIG_RZA_USB) 93 #define XTAL 0xC000 /* b15-14: Crystal selection */ 94 #define XTAL48 0x8000 /* 48MHz */ 95 #define XTAL24 0x4000 /* 24MHz */ 96 #define XTAL12 0x0000 /* 12MHz */ 97 #define XCKE 0x2000 /* b13: External clock enable */ 98 #define PLLC 0x0800 /* b11: PLL control */ 99 #define SCKE 0x0400 /* b10: USB clock enable */ 100 #define PCSDIS 0x0200 /* b9: not CS wakeup */ 101 #define LPSME 0x0100 /* b8: Low power sleep mode */ 102 #endif 103 #define HSE 0x0080 /* b7: Hi-speed enable */ 104 #define DCFM 0x0040 /* b6: Controller function select */ 105 #define DRPD 0x0020 /* b5: D+/- pull down control */ 106 #define DPRPU 0x0010 /* b4: D+ pull up control */ 107 #if defined(CONFIG_RZA_USB) 108 #define XTAL 0x0004 /* b2: Crystal selection */ 109 #define XTAL12 0x0004 /* 12MHz */ 110 #define XTAL48 0x0000 /* 48MHz */ 111 #define UPLLE 0x0002 /* b1: internal PLL control */ 112 #endif 113 #define USBE 0x0001 /* b0: USB module operation enable */ 114 115 /* System Configuration Status Register */ 116 #define OVCBIT 0x8000 /* b15-14: Over-current bit */ 117 #define OVCMON 0xC000 /* b15-14: Over-current monitor */ 118 #define SOFEA 0x0020 /* b5: SOF monitor */ 119 #define IDMON 0x0004 /* b3: ID-pin monitor */ 120 #define LNST 0x0003 /* b1-0: D+, D- line status */ 121 #define SE1 0x0003 /* SE1 */ 122 #define FS_KSTS 0x0002 /* Full-Speed K State */ 123 #define FS_JSTS 0x0001 /* Full-Speed J State */ 124 #define LS_JSTS 0x0002 /* Low-Speed J State */ 125 #define LS_KSTS 0x0001 /* Low-Speed K State */ 126 #define SE0 0x0000 /* SE0 */ 127 128 /* Device State Control Register */ 129 #define EXTLP0 0x0400 /* b10: External port */ 130 #define VBOUT 0x0200 /* b9: VBUS output */ 131 #define WKUP 0x0100 /* b8: Remote wakeup */ 132 #define RWUPE 0x0080 /* b7: Remote wakeup sense */ 133 #define USBRST 0x0040 /* b6: USB reset enable */ 134 #define RESUME 0x0020 /* b5: Resume enable */ 135 #define UACT 0x0010 /* b4: USB bus enable */ 136 #define RHST 0x0007 /* b1-0: Reset handshake status */ 137 #define HSPROC 0x0004 /* HS handshake is processing */ 138 #define HSMODE 0x0003 /* Hi-Speed mode */ 139 #define FSMODE 0x0002 /* Full-Speed mode */ 140 #define LSMODE 0x0001 /* Low-Speed mode */ 141 #define UNDECID 0x0000 /* Undecided */ 142 143 /* Test Mode Register */ 144 #define UTST 0x000F /* b3-0: Test select */ 145 #define H_TST_PACKET 0x000C /* HOST TEST Packet */ 146 #define H_TST_SE0_NAK 0x000B /* HOST TEST SE0 NAK */ 147 #define H_TST_K 0x000A /* HOST TEST K */ 148 #define H_TST_J 0x0009 /* HOST TEST J */ 149 #define H_TST_NORMAL 0x0000 /* HOST Normal Mode */ 150 #define P_TST_PACKET 0x0004 /* PERI TEST Packet */ 151 #define P_TST_SE0_NAK 0x0003 /* PERI TEST SE0 NAK */ 152 #define P_TST_K 0x0002 /* PERI TEST K */ 153 #define P_TST_J 0x0001 /* PERI TEST J */ 154 #define P_TST_NORMAL 0x0000 /* PERI Normal Mode */ 155 156 /* Data Pin Configuration Register */ 157 #define LDRV 0x8000 /* b15: Drive Current Adjust */ 158 #define VIF1 0x0000 /* VIF = 1.8V */ 159 #define VIF3 0x8000 /* VIF = 3.3V */ 160 #define INTA 0x0001 /* b1: USB INT-pin active */ 161 162 /* DMAx Pin Configuration Register */ 163 #define DREQA 0x4000 /* b14: Dreq active select */ 164 #define BURST 0x2000 /* b13: Burst mode */ 165 #define DACKA 0x0400 /* b10: Dack active select */ 166 #define DFORM 0x0380 /* b9-7: DMA mode select */ 167 #define CPU_ADR_RD_WR 0x0000 /* Address + RD/WR mode (CPU bus) */ 168 #define CPU_DACK_RD_WR 0x0100 /* DACK + RD/WR mode (CPU bus) */ 169 #define CPU_DACK_ONLY 0x0180 /* DACK only mode (CPU bus) */ 170 #define SPLIT_DACK_ONLY 0x0200 /* DACK only mode (SPLIT bus) */ 171 #define DENDA 0x0040 /* b6: Dend active select */ 172 #define PKTM 0x0020 /* b5: Packet mode */ 173 #define DENDE 0x0010 /* b4: Dend enable */ 174 #define OBUS 0x0004 /* b2: OUTbus mode */ 175 176 /* CFIFO/DxFIFO Port Select Register */ 177 #define RCNT 0x8000 /* b15: Read count mode */ 178 #define REW 0x4000 /* b14: Buffer rewind */ 179 #define DCLRM 0x2000 /* b13: DMA buffer clear mode */ 180 #define DREQE 0x1000 /* b12: DREQ output enable */ 181 #if defined(CONFIG_SUPERH_ON_CHIP_R8A66597) 182 #define MBW 0x0800 183 #else 184 #if !defined(CONFIG_RZA_USB) 185 #define MBW 0x0400 /* b10: Maximum bit width for FIFO access */ 186 #else 187 #define MBW 0x0800 /* b10: Maximum bit width for FIFO access */ 188 #endif 189 #endif 190 #define MBW_8 0x0000 /* 8bit */ 191 #define MBW_16 0x0400 /* 16bit */ 192 #define MBW_32 0x0800 /* 32bit */ 193 #define BIGEND 0x0100 /* b8: Big endian mode */ 194 #define BYTE_LITTLE 0x0000 /* little dendian */ 195 #define BYTE_BIG 0x0100 /* big endifan */ 196 #define ISEL 0x0020 /* b5: DCP FIFO port direction select */ 197 #define CURPIPE 0x000F /* b2-0: PIPE select */ 198 199 /* CFIFO/DxFIFO Port Control Register */ 200 #define BVAL 0x8000 /* b15: Buffer valid flag */ 201 #define BCLR 0x4000 /* b14: Buffer clear */ 202 #define FRDY 0x2000 /* b13: FIFO ready */ 203 #define DTLN 0x0FFF /* b11-0: FIFO received data length */ 204 205 /* Interrupt Enable Register 0 */ 206 #define VBSE 0x8000 /* b15: VBUS interrupt */ 207 #define RSME 0x4000 /* b14: Resume interrupt */ 208 #define SOFE 0x2000 /* b13: Frame update interrupt */ 209 #define DVSE 0x1000 /* b12: Device state transition interrupt */ 210 #define CTRE 0x0800 /* b11: Control transfer stage transition interrupt */ 211 #define BEMPE 0x0400 /* b10: Buffer empty interrupt */ 212 #define NRDYE 0x0200 /* b9: Buffer not ready interrupt */ 213 #define BRDYE 0x0100 /* b8: Buffer ready interrupt */ 214 215 /* Interrupt Enable Register 1 */ 216 #define OVRCRE 0x8000 /* b15: Over-current interrupt */ 217 #define BCHGE 0x4000 /* b14: USB us chenge interrupt */ 218 #define DTCHE 0x1000 /* b12: Detach sense interrupt */ 219 #define ATTCHE 0x0800 /* b11: Attach sense interrupt */ 220 #define EOFERRE 0x0040 /* b6: EOF error interrupt */ 221 #define SIGNE 0x0020 /* b5: SETUP IGNORE interrupt */ 222 #define SACKE 0x0010 /* b4: SETUP ACK interrupt */ 223 224 /* BRDY Interrupt Enable/Status Register */ 225 #define BRDY9 0x0200 /* b9: PIPE9 */ 226 #define BRDY8 0x0100 /* b8: PIPE8 */ 227 #define BRDY7 0x0080 /* b7: PIPE7 */ 228 #define BRDY6 0x0040 /* b6: PIPE6 */ 229 #define BRDY5 0x0020 /* b5: PIPE5 */ 230 #define BRDY4 0x0010 /* b4: PIPE4 */ 231 #define BRDY3 0x0008 /* b3: PIPE3 */ 232 #define BRDY2 0x0004 /* b2: PIPE2 */ 233 #define BRDY1 0x0002 /* b1: PIPE1 */ 234 #define BRDY0 0x0001 /* b1: PIPE0 */ 235 236 /* NRDY Interrupt Enable/Status Register */ 237 #define NRDY9 0x0200 /* b9: PIPE9 */ 238 #define NRDY8 0x0100 /* b8: PIPE8 */ 239 #define NRDY7 0x0080 /* b7: PIPE7 */ 240 #define NRDY6 0x0040 /* b6: PIPE6 */ 241 #define NRDY5 0x0020 /* b5: PIPE5 */ 242 #define NRDY4 0x0010 /* b4: PIPE4 */ 243 #define NRDY3 0x0008 /* b3: PIPE3 */ 244 #define NRDY2 0x0004 /* b2: PIPE2 */ 245 #define NRDY1 0x0002 /* b1: PIPE1 */ 246 #define NRDY0 0x0001 /* b1: PIPE0 */ 247 248 /* BEMP Interrupt Enable/Status Register */ 249 #define BEMP9 0x0200 /* b9: PIPE9 */ 250 #define BEMP8 0x0100 /* b8: PIPE8 */ 251 #define BEMP7 0x0080 /* b7: PIPE7 */ 252 #define BEMP6 0x0040 /* b6: PIPE6 */ 253 #define BEMP5 0x0020 /* b5: PIPE5 */ 254 #define BEMP4 0x0010 /* b4: PIPE4 */ 255 #define BEMP3 0x0008 /* b3: PIPE3 */ 256 #define BEMP2 0x0004 /* b2: PIPE2 */ 257 #define BEMP1 0x0002 /* b1: PIPE1 */ 258 #define BEMP0 0x0001 /* b0: PIPE0 */ 259 260 /* SOF Pin Configuration Register */ 261 #define TRNENSEL 0x0100 /* b8: Select transaction enable period */ 262 #define BRDYM 0x0040 /* b6: BRDY clear timing */ 263 #define INTL 0x0020 /* b5: Interrupt sense select */ 264 #define EDGESTS 0x0010 /* b4: */ 265 #define SOFMODE 0x000C /* b3-2: SOF pin select */ 266 #define SOF_125US 0x0008 /* SOF OUT 125us Frame Signal */ 267 #define SOF_1MS 0x0004 /* SOF OUT 1ms Frame Signal */ 268 #define SOF_DISABLE 0x0000 /* SOF OUT Disable */ 269 270 /* Interrupt Status Register 0 */ 271 #define VBINT 0x8000 /* b15: VBUS interrupt */ 272 #define RESM 0x4000 /* b14: Resume interrupt */ 273 #define SOFR 0x2000 /* b13: SOF frame update interrupt */ 274 #define DVST 0x1000 /* b12: Device state transition interrupt */ 275 #define CTRT 0x0800 /* b11: Control transfer stage transition interrupt */ 276 #define BEMP 0x0400 /* b10: Buffer empty interrupt */ 277 #define NRDY 0x0200 /* b9: Buffer not ready interrupt */ 278 #define BRDY 0x0100 /* b8: Buffer ready interrupt */ 279 #define VBSTS 0x0080 /* b7: VBUS input port */ 280 #define DVSQ 0x0070 /* b6-4: Device state */ 281 #define DS_SPD_CNFG 0x0070 /* Suspend Configured */ 282 #define DS_SPD_ADDR 0x0060 /* Suspend Address */ 283 #define DS_SPD_DFLT 0x0050 /* Suspend Default */ 284 #define DS_SPD_POWR 0x0040 /* Suspend Powered */ 285 #define DS_SUSP 0x0040 /* Suspend */ 286 #define DS_CNFG 0x0030 /* Configured */ 287 #define DS_ADDS 0x0020 /* Address */ 288 #define DS_DFLT 0x0010 /* Default */ 289 #define DS_POWR 0x0000 /* Powered */ 290 #define DVSQS 0x0030 /* b5-4: Device state */ 291 #define VALID 0x0008 /* b3: Setup packet detected flag */ 292 #define CTSQ 0x0007 /* b2-0: Control transfer stage */ 293 #define CS_SQER 0x0006 /* Sequence error */ 294 #define CS_WRND 0x0005 /* Control write nodata status stage */ 295 #define CS_WRSS 0x0004 /* Control write status stage */ 296 #define CS_WRDS 0x0003 /* Control write data stage */ 297 #define CS_RDSS 0x0002 /* Control read status stage */ 298 #define CS_RDDS 0x0001 /* Control read data stage */ 299 #define CS_IDST 0x0000 /* Idle or setup stage */ 300 301 /* Interrupt Status Register 1 */ 302 #define OVRCR 0x8000 /* b15: Over-current interrupt */ 303 #define BCHG 0x4000 /* b14: USB bus chenge interrupt */ 304 #define DTCH 0x1000 /* b12: Detach sense interrupt */ 305 #define ATTCH 0x0800 /* b11: Attach sense interrupt */ 306 #define EOFERR 0x0040 /* b6: EOF-error interrupt */ 307 #define SIGN 0x0020 /* b5: Setup ignore interrupt */ 308 #define SACK 0x0010 /* b4: Setup acknowledge interrupt */ 309 310 /* Frame Number Register */ 311 #define OVRN 0x8000 /* b15: Overrun error */ 312 #define CRCE 0x4000 /* b14: Received data error */ 313 #define FRNM 0x07FF /* b10-0: Frame number */ 314 315 /* Micro Frame Number Register */ 316 #define UFRNM 0x0007 /* b2-0: Micro frame number */ 317 318 /* Default Control Pipe Maxpacket Size Register */ 319 /* Pipe Maxpacket Size Register */ 320 #define DEVSEL 0xF000 /* b15-14: Device address select */ 321 #define MAXP 0x007F /* b6-0: Maxpacket size of default control pipe */ 322 323 /* Default Control Pipe Control Register */ 324 #define BSTS 0x8000 /* b15: Buffer status */ 325 #define SUREQ 0x4000 /* b14: Send USB request */ 326 #define CSCLR 0x2000 /* b13: complete-split status clear */ 327 #define CSSTS 0x1000 /* b12: complete-split status */ 328 #define SUREQCLR 0x0800 /* b11: stop setup request */ 329 #define SQCLR 0x0100 /* b8: Sequence toggle bit clear */ 330 #define SQSET 0x0080 /* b7: Sequence toggle bit set */ 331 #define SQMON 0x0040 /* b6: Sequence toggle bit monitor */ 332 #define PBUSY 0x0020 /* b5: pipe busy */ 333 #define PINGE 0x0010 /* b4: ping enable */ 334 #define CCPL 0x0004 /* b2: Enable control transfer complete */ 335 #define PID 0x0003 /* b1-0: Response PID */ 336 #define PID_STALL11 0x0003 /* STALL */ 337 #define PID_STALL 0x0002 /* STALL */ 338 #define PID_BUF 0x0001 /* BUF */ 339 #define PID_NAK 0x0000 /* NAK */ 340 341 /* Pipe Window Select Register */ 342 #define PIPENM 0x0007 /* b2-0: Pipe select */ 343 344 /* Pipe Configuration Register */ 345 #define R8A66597_TYP 0xC000 /* b15-14: Transfer type */ 346 #define R8A66597_ISO 0xC000 /* Isochronous */ 347 #define R8A66597_INT 0x8000 /* Interrupt */ 348 #define R8A66597_BULK 0x4000 /* Bulk */ 349 #define R8A66597_BFRE 0x0400 /* b10: Buffer ready interrupt mode select */ 350 #define R8A66597_DBLB 0x0200 /* b9: Double buffer mode select */ 351 #define R8A66597_CNTMD 0x0100 /* b8: Continuous transfer mode select */ 352 #define R8A66597_SHTNAK 0x0080 /* b7: Transfer end NAK */ 353 #define R8A66597_DIR 0x0010 /* b4: Transfer direction select */ 354 #define R8A66597_EPNUM 0x000F /* b3-0: Eendpoint number select */ 355 356 /* Pipe Buffer Configuration Register */ 357 #define BUFSIZE 0x7C00 /* b14-10: Pipe buffer size */ 358 #define BUFNMB 0x007F /* b6-0: Pipe buffer number */ 359 #define PIPE0BUF 256 360 #define PIPExBUF 64 361 362 /* Pipe Maxpacket Size Register */ 363 #define MXPS 0x07FF /* b10-0: Maxpacket size */ 364 365 /* Pipe Cycle Configuration Register */ 366 #define IFIS 0x1000 /* b12: Isochronous in-buffer flush mode select */ 367 #define IITV 0x0007 /* b2-0: Isochronous interval */ 368 369 /* Pipex Control Register */ 370 #define BSTS 0x8000 /* b15: Buffer status */ 371 #define INBUFM 0x4000 /* b14: IN buffer monitor (Only for PIPE1 to 5) */ 372 #define CSCLR 0x2000 /* b13: complete-split status clear */ 373 #define CSSTS 0x1000 /* b12: complete-split status */ 374 #define ATREPM 0x0400 /* b10: Auto repeat mode */ 375 #define ACLRM 0x0200 /* b9: Out buffer auto clear mode */ 376 #define SQCLR 0x0100 /* b8: Sequence toggle bit clear */ 377 #define SQSET 0x0080 /* b7: Sequence toggle bit set */ 378 #define SQMON 0x0040 /* b6: Sequence toggle bit monitor */ 379 #define PBUSY 0x0020 /* b5: pipe busy */ 380 #define PID 0x0003 /* b1-0: Response PID */ 381 382 /* PIPExTRE */ 383 #define TRENB 0x0200 /* b9: Transaction counter enable */ 384 #define TRCLR 0x0100 /* b8: Transaction counter clear */ 385 386 /* PIPExTRN */ 387 #define TRNCNT 0xFFFF /* b15-0: Transaction counter */ 388 389 /* DEVADDx */ 390 #define UPPHUB 0x7800 391 #define HUBPORT 0x0700 392 #define USBSPD 0x00C0 393 #define RTPORT 0x0001 394 395 /* Suspend Mode Register */ 396 #define SUSPM 0x4000 /* b14: Suspend */ 397 398 #define R8A66597_MAX_NUM_PIPE 10 399 #define R8A66597_BUF_BSIZE 8 400 #define R8A66597_MAX_DEVICE 10 401 #if defined(CONFIG_SUPERH_ON_CHIP_R8A66597) 402 #define R8A66597_MAX_ROOT_HUB 1 403 #else 404 #define R8A66597_MAX_ROOT_HUB 2 405 #endif 406 #define R8A66597_MAX_SAMPLING 5 407 #define R8A66597_RH_POLL_TIME 10 408 409 #define BULK_IN_PIPENUM 3 410 #define BULK_IN_BUFNUM 8 411 412 #define BULK_OUT_PIPENUM 4 413 #define BULK_OUT_BUFNUM 40 414 415 #define check_bulk_or_isoc(pipenum) ((pipenum >= 1 && pipenum <= 5)) 416 #define check_interrupt(pipenum) ((pipenum >= 6 && pipenum <= 9)) 417 #define make_devsel(addr) (addr << 12) 418 419 struct r8a66597 { 420 unsigned long reg; 421 unsigned short pipe_config; /* bit field */ 422 unsigned short port_status; 423 unsigned short port_change; 424 u16 speed; /* HSMODE or FSMODE or LSMODE */ 425 unsigned char rh_devnum; 426 }; 427 428 static inline u16 r8a66597_read(struct r8a66597 *r8a66597, unsigned long offset) 429 { 430 return inw(r8a66597->reg + offset); 431 } 432 433 static inline void r8a66597_read_fifo(struct r8a66597 *r8a66597, 434 unsigned long offset, void *buf, 435 int len) 436 { 437 int i; 438 #if defined(CONFIG_SUPERH_ON_CHIP_R8A66597) || defined(CONFIG_RZA_USB) 439 unsigned long fifoaddr = r8a66597->reg + offset; 440 unsigned long count; 441 unsigned long *p = buf; 442 443 count = len / 4; 444 for (i = 0; i < count; i++) 445 p[i] = inl(r8a66597->reg + offset); 446 447 if (len & 0x00000003) { 448 unsigned long tmp = inl(fifoaddr); 449 memcpy((unsigned char *)buf + count * 4, &tmp, len & 0x03); 450 } 451 #else 452 unsigned short *p = buf; 453 454 len = (len + 1) / 2; 455 for (i = 0; i < len; i++) 456 p[i] = inw(r8a66597->reg + offset); 457 #endif 458 } 459 460 static inline void r8a66597_write(struct r8a66597 *r8a66597, u16 val, 461 unsigned long offset) 462 { 463 outw(val, r8a66597->reg + offset); 464 } 465 466 static inline void r8a66597_write_fifo(struct r8a66597 *r8a66597, 467 unsigned long offset, void *buf, 468 int len) 469 { 470 int i; 471 unsigned long fifoaddr = r8a66597->reg + offset; 472 #if defined(CONFIG_SUPERH_ON_CHIP_R8A66597) || defined(CONFIG_RZA_USB) 473 unsigned long count; 474 unsigned char *pb; 475 unsigned long *p = buf; 476 477 count = len / 4; 478 for (i = 0; i < count; i++) 479 outl(p[i], fifoaddr); 480 481 if (len & 0x00000003) { 482 pb = (unsigned char *)buf + count * 4; 483 for (i = 0; i < (len & 0x00000003); i++) { 484 if (r8a66597_read(r8a66597, CFIFOSEL) & BIGEND) 485 outb(pb[i], fifoaddr + i); 486 else 487 outb(pb[i], fifoaddr + 3 - i); 488 } 489 } 490 #else 491 int odd = len & 0x0001; 492 unsigned short *p = buf; 493 494 len = len / 2; 495 for (i = 0; i < len; i++) 496 outw(p[i], fifoaddr); 497 498 if (odd) { 499 unsigned char *pb = (unsigned char *)(buf + len); 500 outb(*pb, fifoaddr); 501 } 502 #endif 503 } 504 505 static inline void r8a66597_mdfy(struct r8a66597 *r8a66597, 506 u16 val, u16 pat, unsigned long offset) 507 { 508 u16 tmp; 509 tmp = r8a66597_read(r8a66597, offset); 510 tmp = tmp & (~pat); 511 tmp = tmp | val; 512 r8a66597_write(r8a66597, tmp, offset); 513 } 514 515 #define r8a66597_bclr(r8a66597, val, offset) \ 516 r8a66597_mdfy(r8a66597, 0, val, offset) 517 #define r8a66597_bset(r8a66597, val, offset) \ 518 r8a66597_mdfy(r8a66597, val, 0, offset) 519 520 static inline unsigned long get_syscfg_reg(int port) 521 { 522 return port == 0 ? SYSCFG0 : SYSCFG1; 523 } 524 525 static inline unsigned long get_syssts_reg(int port) 526 { 527 return port == 0 ? SYSSTS0 : SYSSTS1; 528 } 529 530 static inline unsigned long get_dvstctr_reg(int port) 531 { 532 return port == 0 ? DVSTCTR0 : DVSTCTR1; 533 } 534 535 static inline unsigned long get_dmacfg_reg(int port) 536 { 537 return port == 0 ? DMA0CFG : DMA1CFG; 538 } 539 540 static inline unsigned long get_intenb_reg(int port) 541 { 542 return port == 0 ? INTENB1 : INTENB2; 543 } 544 545 static inline unsigned long get_intsts_reg(int port) 546 { 547 return port == 0 ? INTSTS1 : INTSTS2; 548 } 549 550 static inline u16 get_rh_usb_speed(struct r8a66597 *r8a66597, int port) 551 { 552 unsigned long dvstctr_reg = get_dvstctr_reg(port); 553 554 return r8a66597_read(r8a66597, dvstctr_reg) & RHST; 555 } 556 557 static inline void r8a66597_port_power(struct r8a66597 *r8a66597, int port, 558 int power) 559 { 560 unsigned long dvstctr_reg = get_dvstctr_reg(port); 561 562 if (power) 563 r8a66597_bset(r8a66597, VBOUT, dvstctr_reg); 564 else 565 r8a66597_bclr(r8a66597, VBOUT, dvstctr_reg); 566 } 567 568 #define get_pipectr_addr(pipenum) (PIPE1CTR + (pipenum - 1) * 2) 569 #define get_pipetre_addr(pipenum) (PIPE1TRE + (pipenum - 1) * 4) 570 #define get_pipetrn_addr(pipenum) (PIPE1TRN + (pipenum - 1) * 4) 571 #define get_devadd_addr(address) (DEVADD0 + address * 2) 572 573 574 /* USB HUB CONSTANTS (not OHCI-specific; see hub.h, based on usb_ohci.h) */ 575 576 /* destination of request */ 577 #define RH_INTERFACE 0x01 578 #define RH_ENDPOINT 0x02 579 #define RH_OTHER 0x03 580 581 #define RH_CLASS 0x20 582 #define RH_VENDOR 0x40 583 584 /* Requests: bRequest << 8 | bmRequestType */ 585 #define RH_GET_STATUS 0x0080 586 #define RH_CLEAR_FEATURE 0x0100 587 #define RH_SET_FEATURE 0x0300 588 #define RH_SET_ADDRESS 0x0500 589 #define RH_GET_DESCRIPTOR 0x0680 590 #define RH_SET_DESCRIPTOR 0x0700 591 #define RH_GET_CONFIGURATION 0x0880 592 #define RH_SET_CONFIGURATION 0x0900 593 #define RH_GET_STATE 0x0280 594 #define RH_GET_INTERFACE 0x0A80 595 #define RH_SET_INTERFACE 0x0B00 596 #define RH_SYNC_FRAME 0x0C80 597 /* Our Vendor Specific Request */ 598 #define RH_SET_EP 0x2000 599 600 /* Hub port features */ 601 #define RH_PORT_CONNECTION 0x00 602 #define RH_PORT_ENABLE 0x01 603 #define RH_PORT_SUSPEND 0x02 604 #define RH_PORT_OVER_CURRENT 0x03 605 #define RH_PORT_RESET 0x04 606 #define RH_PORT_POWER 0x08 607 #define RH_PORT_LOW_SPEED 0x09 608 609 #define RH_C_PORT_CONNECTION 0x10 610 #define RH_C_PORT_ENABLE 0x11 611 #define RH_C_PORT_SUSPEND 0x12 612 #define RH_C_PORT_OVER_CURRENT 0x13 613 #define RH_C_PORT_RESET 0x14 614 615 /* Hub features */ 616 #define RH_C_HUB_LOCAL_POWER 0x00 617 #define RH_C_HUB_OVER_CURRENT 0x01 618 619 #define RH_DEVICE_REMOTE_WAKEUP 0x00 620 #define RH_ENDPOINT_STALL 0x01 621 622 #define RH_ACK 0x01 623 #define RH_REQ_ERR -1 624 #define RH_NACK 0x00 625 626 /* OHCI ROOT HUB REGISTER MASKS */ 627 628 /* roothub.portstatus [i] bits */ 629 #define RH_PS_CCS 0x00000001 /* current connect status */ 630 #define RH_PS_PES 0x00000002 /* port enable status*/ 631 #define RH_PS_PSS 0x00000004 /* port suspend status */ 632 #define RH_PS_POCI 0x00000008 /* port over current indicator */ 633 #define RH_PS_PRS 0x00000010 /* port reset status */ 634 #define RH_PS_PPS 0x00000100 /* port power status */ 635 #define RH_PS_LSDA 0x00000200 /* low speed device attached */ 636 #define RH_PS_CSC 0x00010000 /* connect status change */ 637 #define RH_PS_PESC 0x00020000 /* port enable status change */ 638 #define RH_PS_PSSC 0x00040000 /* port suspend status change */ 639 #define RH_PS_OCIC 0x00080000 /* over current indicator change */ 640 #define RH_PS_PRSC 0x00100000 /* port reset status change */ 641 642 /* roothub.status bits */ 643 #define RH_HS_LPS 0x00000001 /* local power status */ 644 #define RH_HS_OCI 0x00000002 /* over current indicator */ 645 #define RH_HS_DRWE 0x00008000 /* device remote wakeup enable */ 646 #define RH_HS_LPSC 0x00010000 /* local power status change */ 647 #define RH_HS_OCIC 0x00020000 /* over current indicator change */ 648 #define RH_HS_CRWE 0x80000000 /* clear remote wakeup enable */ 649 650 /* roothub.b masks */ 651 #define RH_B_DR 0x0000ffff /* device removable flags */ 652 #define RH_B_PPCM 0xffff0000 /* port power control mask */ 653 654 /* roothub.a masks */ 655 #define RH_A_NDP (0xff << 0) /* number of downstream ports */ 656 #define RH_A_PSM (1 << 8) /* power switching mode */ 657 #define RH_A_NPS (1 << 9) /* no power switching */ 658 #define RH_A_DT (1 << 10) /* device type (mbz) */ 659 #define RH_A_OCPM (1 << 11) /* over current protection mode */ 660 #define RH_A_NOCP (1 << 12) /* no over current protection */ 661 #define RH_A_POTPGT (0xff << 24) /* power on to power good time */ 662 663 #endif /* __R8A66597_H__ */ 664