1 /* 2 * Copyright (C) 2008 by NXP Semiconductors 3 * @Author: Based on code by Kevin Wells 4 * @Descr: USB driver - Embedded Artists LPC3250 OEM Board support functions 5 * 6 * Copyright (c) 2015 Tyco Fire Protection Products. 7 * 8 * SPDX-License-Identifier: GPL-2.0+ 9 */ 10 11 #include <common.h> 12 #include <dm.h> 13 #include <errno.h> 14 #include <wait_bit.h> 15 #include <asm/io.h> 16 #include <asm/arch/cpu.h> 17 #include <asm/arch/clk.h> 18 #include <asm/arch/i2c.h> 19 #include <usb.h> 20 #include <i2c.h> 21 22 /* OTG I2C controller module register structures */ 23 struct otgi2c_regs { 24 u32 otg_i2c_txrx; /* OTG I2C Tx/Rx Data FIFO */ 25 u32 otg_i2c_stat; /* OTG I2C Status Register */ 26 u32 otg_i2c_ctrl; /* OTG I2C Control Register */ 27 u32 otg_i2c_clk_hi; /* OTG I2C Clock Divider high */ 28 u32 otg_i2c_clk_lo; /* OTG I2C Clock Divider low */ 29 }; 30 31 /* OTG controller module register structures */ 32 struct otg_regs { 33 u32 reserved1[64]; 34 u32 otg_int_sts; /* OTG int status register */ 35 u32 otg_int_enab; /* OTG int enable register */ 36 u32 otg_int_set; /* OTG int set register */ 37 u32 otg_int_clr; /* OTG int clear register */ 38 u32 otg_sts_ctrl; /* OTG status/control register */ 39 u32 otg_timer; /* OTG timer register */ 40 u32 reserved2[122]; 41 struct otgi2c_regs otg_i2c; 42 u32 reserved3[824]; 43 u32 otg_clk_ctrl; /* OTG clock control reg */ 44 u32 otg_clk_sts; /* OTG clock status reg */ 45 }; 46 47 /* otg_sts_ctrl register definitions */ 48 #define OTG_HOST_EN (1 << 0) /* Enable host mode */ 49 50 /* otg_clk_ctrl and otg_clk_sts register definitions */ 51 #define OTG_CLK_AHB_EN (1 << 4) /* Enable AHB clock */ 52 #define OTG_CLK_OTG_EN (1 << 3) /* Enable OTG clock */ 53 #define OTG_CLK_I2C_EN (1 << 2) /* Enable I2C clock */ 54 #define OTG_CLK_HOST_EN (1 << 0) /* Enable host clock */ 55 56 /* ISP1301 USB transceiver I2C registers */ 57 #define MC1_SPEED_REG (1 << 0) 58 #define MC1_DAT_SE0 (1 << 2) 59 #define MC1_UART_EN (1 << 6) 60 61 #define MC2_SPD_SUSP_CTRL (1 << 1) 62 #define MC2_BI_DI (1 << 2) 63 #define MC2_PSW_EN (1 << 6) 64 65 #define OTG1_DP_PULLUP (1 << 0) 66 #define OTG1_DM_PULLUP (1 << 1) 67 #define OTG1_DP_PULLDOWN (1 << 2) 68 #define OTG1_DM_PULLDOWN (1 << 3) 69 #define OTG1_VBUS_DRV (1 << 5) 70 71 #define ISP1301_I2C_ADDR CONFIG_USB_ISP1301_I2C_ADDR 72 73 #define ISP1301_I2C_MODE_CONTROL_1_SET 0x04 74 #define ISP1301_I2C_MODE_CONTROL_1_CLR 0x05 75 #define ISP1301_I2C_MODE_CONTROL_2_SET 0x12 76 #define ISP1301_I2C_MODE_CONTROL_2_CLR 0x13 77 #define ISP1301_I2C_OTG_CONTROL_1_SET 0x06 78 #define ISP1301_I2C_OTG_CONTROL_1_CLR 0x07 79 #define ISP1301_I2C_INTERRUPT_LATCH_CLR 0x0B 80 #define ISP1301_I2C_INTERRUPT_FALLING_CLR 0x0D 81 #define ISP1301_I2C_INTERRUPT_RISING_CLR 0x0F 82 83 static struct otg_regs *otg = (struct otg_regs *)USB_BASE; 84 static struct clk_pm_regs *clk_pwr = (struct clk_pm_regs *)CLK_PM_BASE; 85 86 static int isp1301_set_value(struct udevice *dev, int reg, u8 value) 87 { 88 #ifndef CONFIG_DM_I2C 89 return i2c_write(ISP1301_I2C_ADDR, reg, 1, &value, 1); 90 #else 91 return dm_i2c_write(dev, reg, &value, 1); 92 #endif 93 } 94 95 static void isp1301_configure(struct udevice *dev) 96 { 97 #ifndef CONFIG_DM_I2C 98 i2c_set_bus_num(I2C_2); 99 #endif 100 101 /* 102 * LPC32XX only supports DAT_SE0 USB mode 103 * This sequence is important 104 */ 105 106 /* Disable transparent UART mode first */ 107 isp1301_set_value(dev, ISP1301_I2C_MODE_CONTROL_1_CLR, MC1_UART_EN); 108 109 isp1301_set_value(dev, ISP1301_I2C_MODE_CONTROL_1_CLR, ~MC1_SPEED_REG); 110 isp1301_set_value(dev, ISP1301_I2C_MODE_CONTROL_1_SET, MC1_SPEED_REG); 111 isp1301_set_value(dev, ISP1301_I2C_MODE_CONTROL_2_CLR, ~0); 112 isp1301_set_value(dev, ISP1301_I2C_MODE_CONTROL_2_SET, 113 MC2_BI_DI | MC2_PSW_EN | MC2_SPD_SUSP_CTRL); 114 115 isp1301_set_value(dev, ISP1301_I2C_OTG_CONTROL_1_CLR, ~0); 116 isp1301_set_value(dev, ISP1301_I2C_MODE_CONTROL_1_SET, MC1_DAT_SE0); 117 isp1301_set_value(dev, ISP1301_I2C_OTG_CONTROL_1_SET, 118 OTG1_DM_PULLDOWN | OTG1_DP_PULLDOWN); 119 isp1301_set_value(dev, ISP1301_I2C_OTG_CONTROL_1_CLR, 120 OTG1_DM_PULLUP | OTG1_DP_PULLUP); 121 isp1301_set_value(dev, ISP1301_I2C_INTERRUPT_LATCH_CLR, ~0); 122 isp1301_set_value(dev, ISP1301_I2C_INTERRUPT_FALLING_CLR, ~0); 123 isp1301_set_value(dev, ISP1301_I2C_INTERRUPT_RISING_CLR, ~0); 124 125 /* Enable usb_need_clk clock after transceiver is initialized */ 126 setbits_le32(&clk_pwr->usb_ctrl, CLK_USBCTRL_USBDVND_EN); 127 } 128 129 static int usbpll_setup(void) 130 { 131 u32 ret; 132 133 /* make sure clocks are disabled */ 134 clrbits_le32(&clk_pwr->usb_ctrl, 135 CLK_USBCTRL_CLK_EN1 | CLK_USBCTRL_CLK_EN2); 136 137 /* start PLL clock input */ 138 setbits_le32(&clk_pwr->usb_ctrl, CLK_USBCTRL_CLK_EN1); 139 140 /* Setup PLL. */ 141 setbits_le32(&clk_pwr->usb_ctrl, 142 CLK_USBCTRL_FDBK_PLUS1(192 - 1)); 143 setbits_le32(&clk_pwr->usb_ctrl, CLK_USBCTRL_POSTDIV_2POW(0x01)); 144 setbits_le32(&clk_pwr->usb_ctrl, CLK_USBCTRL_PLL_PWRUP); 145 146 ret = wait_for_bit_le32(&clk_pwr->usb_ctrl, CLK_USBCTRL_PLL_STS, 147 true, CONFIG_SYS_HZ, false); 148 if (ret) 149 return ret; 150 151 /* enable PLL output */ 152 setbits_le32(&clk_pwr->usb_ctrl, CLK_USBCTRL_CLK_EN2); 153 154 return 0; 155 } 156 157 int usb_cpu_init(void) 158 { 159 u32 ret; 160 struct udevice *dev = NULL; 161 162 #ifdef CONFIG_DM_I2C 163 ret = i2c_get_chip_for_busnum(I2C_2, ISP1301_I2C_ADDR, 1, &dev); 164 if (ret) { 165 debug("%s: No bus %d\n", __func__, I2C_2); 166 return ret; 167 } 168 #endif 169 170 /* 171 * USB pins routing setup is done by "lpc32xx_usb_init()" and should 172 * be call by board "board_init()" or "misc_init_r()" functions. 173 */ 174 175 /* enable AHB slave USB clock */ 176 setbits_le32(&clk_pwr->usb_ctrl, 177 CLK_USBCTRL_HCLK_EN | CLK_USBCTRL_BUS_KEEPER); 178 179 /* enable I2C clock */ 180 writel(OTG_CLK_I2C_EN, &otg->otg_clk_ctrl); 181 ret = wait_for_bit_le32(&otg->otg_clk_sts, OTG_CLK_I2C_EN, true, 182 CONFIG_SYS_HZ, false); 183 if (ret) 184 return ret; 185 186 /* Configure ISP1301 */ 187 isp1301_configure(dev); 188 189 /* setup USB clocks and PLL */ 190 ret = usbpll_setup(); 191 if (ret) 192 return ret; 193 194 /* enable usb_host_need_clk */ 195 setbits_le32(&clk_pwr->usb_ctrl, CLK_USBCTRL_USBHSTND_EN); 196 197 /* enable all needed USB clocks */ 198 const u32 mask = OTG_CLK_AHB_EN | OTG_CLK_OTG_EN | 199 OTG_CLK_I2C_EN | OTG_CLK_HOST_EN; 200 writel(mask, &otg->otg_clk_ctrl); 201 202 ret = wait_for_bit_le32(&otg->otg_clk_sts, mask, true, 203 CONFIG_SYS_HZ, false); 204 if (ret) 205 return ret; 206 207 setbits_le32(&otg->otg_sts_ctrl, OTG_HOST_EN); 208 isp1301_set_value(dev, ISP1301_I2C_OTG_CONTROL_1_SET, OTG1_VBUS_DRV); 209 210 return 0; 211 } 212 213 int usb_cpu_stop(void) 214 { 215 struct udevice *dev = NULL; 216 int ret = 0; 217 218 #ifdef CONFIG_DM_I2C 219 ret = i2c_get_chip_for_busnum(I2C_2, ISP1301_I2C_ADDR, 1, &dev); 220 if (ret) { 221 debug("%s: No bus %d\n", __func__, I2C_2); 222 return ret; 223 } 224 #endif 225 226 /* vbus off */ 227 isp1301_set_value(dev, ISP1301_I2C_OTG_CONTROL_1_SET, OTG1_VBUS_DRV); 228 229 clrbits_le32(&otg->otg_sts_ctrl, OTG_HOST_EN); 230 231 clrbits_le32(&clk_pwr->usb_ctrl, CLK_USBCTRL_HCLK_EN); 232 233 return ret; 234 } 235 236 int usb_cpu_init_fail(void) 237 { 238 return usb_cpu_stop(); 239 } 240