1 /* 2 * Copyright (c) 2011 The Chromium OS Authors. 3 * Copyright (c) 2009-2015 NVIDIA Corporation 4 * Copyright (c) 2013 Lucas Stach 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #include <common.h> 10 #include <dm.h> 11 #include <linux/errno.h> 12 #include <asm/io.h> 13 #include <asm-generic/gpio.h> 14 #include <asm/arch/clock.h> 15 #include <asm/arch-tegra/usb.h> 16 #include <asm/arch-tegra/clk_rst.h> 17 #include <usb.h> 18 #include <usb/ulpi.h> 19 #include <libfdt.h> 20 #include <fdtdec.h> 21 22 #include "ehci.h" 23 24 DECLARE_GLOBAL_DATA_PTR; 25 26 #define USB1_ADDR_MASK 0xFFFF0000 27 28 #define HOSTPC1_DEVLC 0x84 29 #define HOSTPC1_PSPD(x) (((x) >> 25) & 0x3) 30 31 #ifdef CONFIG_USB_ULPI 32 #ifndef CONFIG_USB_ULPI_VIEWPORT 33 #error "To use CONFIG_USB_ULPI on Tegra Boards you have to also \ 34 define CONFIG_USB_ULPI_VIEWPORT" 35 #endif 36 #endif 37 38 /* Parameters we need for USB */ 39 enum { 40 PARAM_DIVN, /* PLL FEEDBACK DIVIDer */ 41 PARAM_DIVM, /* PLL INPUT DIVIDER */ 42 PARAM_DIVP, /* POST DIVIDER (2^N) */ 43 PARAM_CPCON, /* BASE PLLC CHARGE Pump setup ctrl */ 44 PARAM_LFCON, /* BASE PLLC LOOP FILter setup ctrl */ 45 PARAM_ENABLE_DELAY_COUNT, /* PLL-U Enable Delay Count */ 46 PARAM_STABLE_COUNT, /* PLL-U STABLE count */ 47 PARAM_ACTIVE_DELAY_COUNT, /* PLL-U Active delay count */ 48 PARAM_XTAL_FREQ_COUNT, /* PLL-U XTAL frequency count */ 49 PARAM_DEBOUNCE_A_TIME, /* 10MS DELAY for BIAS_DEBOUNCE_A */ 50 PARAM_BIAS_TIME, /* 20US DELAY AFter bias cell op */ 51 52 PARAM_COUNT 53 }; 54 55 /* Possible port types (dual role mode) */ 56 enum dr_mode { 57 DR_MODE_NONE = 0, 58 DR_MODE_HOST, /* supports host operation */ 59 DR_MODE_DEVICE, /* supports device operation */ 60 DR_MODE_OTG, /* supports both */ 61 }; 62 63 enum usb_ctlr_type { 64 USB_CTLR_T20, 65 USB_CTLR_T30, 66 USB_CTLR_T114, 67 USB_CTLR_T210, 68 69 USB_CTRL_COUNT, 70 }; 71 72 /* Information about a USB port */ 73 struct fdt_usb { 74 struct ehci_ctrl ehci; 75 struct usb_ctlr *reg; /* address of registers in physical memory */ 76 unsigned utmi:1; /* 1 if port has external tranceiver, else 0 */ 77 unsigned ulpi:1; /* 1 if port has external ULPI transceiver */ 78 unsigned enabled:1; /* 1 to enable, 0 to disable */ 79 unsigned has_legacy_mode:1; /* 1 if this port has legacy mode */ 80 enum usb_ctlr_type type; 81 enum usb_init_type init_type; 82 enum dr_mode dr_mode; /* dual role mode */ 83 enum periph_id periph_id;/* peripheral id */ 84 struct gpio_desc vbus_gpio; /* GPIO for vbus enable */ 85 struct gpio_desc phy_reset_gpio; /* GPIO to reset ULPI phy */ 86 }; 87 88 /* 89 * This table has USB timing parameters for each Oscillator frequency we 90 * support. There are four sets of values: 91 * 92 * 1. PLLU configuration information (reference clock is osc/clk_m and 93 * PLLU-FOs are fixed at 12MHz/60MHz/480MHz). 94 * 95 * Reference frequency 13.0MHz 19.2MHz 12.0MHz 26.0MHz 96 * ---------------------------------------------------------------------- 97 * DIVN 960 (0x3c0) 200 (0c8) 960 (3c0h) 960 (3c0) 98 * DIVM 13 (0d) 4 (04) 12 (0c) 26 (1a) 99 * Filter frequency (MHz) 1 4.8 6 2 100 * CPCON 1100b 0011b 1100b 1100b 101 * LFCON0 0 0 0 0 102 * 103 * 2. PLL CONFIGURATION & PARAMETERS for different clock generators: 104 * 105 * Reference frequency 13.0MHz 19.2MHz 12.0MHz 26.0MHz 106 * --------------------------------------------------------------------------- 107 * PLLU_ENABLE_DLY_COUNT 02 (0x02) 03 (03) 02 (02) 04 (04) 108 * PLLU_STABLE_COUNT 51 (33) 75 (4B) 47 (2F) 102 (66) 109 * PLL_ACTIVE_DLY_COUNT 05 (05) 06 (06) 04 (04) 09 (09) 110 * XTAL_FREQ_COUNT 127 (7F) 187 (BB) 118 (76) 254 (FE) 111 * 112 * 3. Debounce values IdDig, Avalid, Bvalid, VbusValid, VbusWakeUp, and 113 * SessEnd. Each of these signals have their own debouncer and for each of 114 * those one out of two debouncing times can be chosen (BIAS_DEBOUNCE_A or 115 * BIAS_DEBOUNCE_B). 116 * 117 * The values of DEBOUNCE_A and DEBOUNCE_B are calculated as follows: 118 * 0xffff -> No debouncing at all 119 * <n> ms = <n> *1000 / (1/19.2MHz) / 4 120 * 121 * So to program a 1 ms debounce for BIAS_DEBOUNCE_A, we have: 122 * BIAS_DEBOUNCE_A[15:0] = 1000 * 19.2 / 4 = 4800 = 0x12c0 123 * 124 * We need to use only DebounceA for BOOTROM. We don't need the DebounceB 125 * values, so we can keep those to default. 126 * 127 * 4. The 20 microsecond delay after bias cell operation. 128 */ 129 static const unsigned T20_usb_pll[CLOCK_OSC_FREQ_COUNT][PARAM_COUNT] = { 130 /* DivN, DivM, DivP, CPCON, LFCON, Delays Debounce, Bias */ 131 { 0x3C0, 0x0D, 0x00, 0xC, 0, 0x02, 0x33, 0x05, 0x7F, 0x7EF4, 5 }, 132 { 0x0C8, 0x04, 0x00, 0x3, 0, 0x03, 0x4B, 0x06, 0xBB, 0xBB80, 7 }, 133 { 0x3C0, 0x0C, 0x00, 0xC, 0, 0x02, 0x2F, 0x04, 0x76, 0x7530, 5 }, 134 { 0x3C0, 0x1A, 0x00, 0xC, 0, 0x04, 0x66, 0x09, 0xFE, 0xFDE8, 9 }, 135 { 0x000, 0x00, 0x00, 0x0, 0, 0x00, 0x00, 0x00, 0x00, 0x0000, 0 }, 136 { 0x000, 0x00, 0x00, 0x0, 0, 0x00, 0x00, 0x00, 0x00, 0x0000, 0 } 137 }; 138 139 static const unsigned T30_usb_pll[CLOCK_OSC_FREQ_COUNT][PARAM_COUNT] = { 140 /* DivN, DivM, DivP, CPCON, LFCON, Delays Debounce, Bias */ 141 { 0x3C0, 0x0D, 0x00, 0xC, 1, 0x02, 0x33, 0x09, 0x7F, 0x7EF4, 5 }, 142 { 0x0C8, 0x04, 0x00, 0x3, 0, 0x03, 0x4B, 0x0C, 0xBB, 0xBB80, 7 }, 143 { 0x3C0, 0x0C, 0x00, 0xC, 1, 0x02, 0x2F, 0x08, 0x76, 0x7530, 5 }, 144 { 0x3C0, 0x1A, 0x00, 0xC, 1, 0x04, 0x66, 0x09, 0xFE, 0xFDE8, 9 }, 145 { 0x000, 0x00, 0x00, 0x0, 0, 0x00, 0x00, 0x00, 0x00, 0x0000, 0 }, 146 { 0x000, 0x00, 0x00, 0x0, 0, 0x00, 0x00, 0x00, 0x00, 0x0000, 0 } 147 }; 148 149 static const unsigned T114_usb_pll[CLOCK_OSC_FREQ_COUNT][PARAM_COUNT] = { 150 /* DivN, DivM, DivP, CPCON, LFCON, Delays Debounce, Bias */ 151 { 0x3C0, 0x0D, 0x00, 0xC, 2, 0x02, 0x33, 0x09, 0x7F, 0x7EF4, 6 }, 152 { 0x0C8, 0x04, 0x00, 0x3, 2, 0x03, 0x4B, 0x0C, 0xBB, 0xBB80, 8 }, 153 { 0x3C0, 0x0C, 0x00, 0xC, 2, 0x02, 0x2F, 0x08, 0x76, 0x7530, 5 }, 154 { 0x3C0, 0x1A, 0x00, 0xC, 2, 0x04, 0x66, 0x09, 0xFE, 0xFDE8, 11 }, 155 { 0x000, 0x00, 0x00, 0x0, 0, 0x00, 0x00, 0x00, 0x00, 0x0000, 0 }, 156 { 0x000, 0x00, 0x00, 0x0, 0, 0x00, 0x00, 0x00, 0x00, 0x0000, 0 } 157 }; 158 159 /* NOTE: 13/26MHz settings are N/A for T210, so dupe 12MHz settings for now */ 160 static const unsigned T210_usb_pll[CLOCK_OSC_FREQ_COUNT][PARAM_COUNT] = { 161 /* DivN, DivM, DivP, KCP, KVCO, Delays Debounce, Bias */ 162 { 0x028, 0x01, 0x01, 0x0, 0, 0x02, 0x2F, 0x08, 0x76, 32500, 5 }, 163 { 0x019, 0x01, 0x01, 0x0, 0, 0x03, 0x4B, 0x0C, 0xBB, 48000, 8 }, 164 { 0x028, 0x01, 0x01, 0x0, 0, 0x02, 0x2F, 0x08, 0x76, 30000, 5 }, 165 { 0x028, 0x01, 0x01, 0x0, 0, 0x02, 0x2F, 0x08, 0x76, 65000, 5 }, 166 { 0x019, 0x02, 0x01, 0x0, 0, 0x05, 0x96, 0x18, 0x177, 96000, 15 }, 167 { 0x028, 0x04, 0x01, 0x0, 0, 0x04, 0x66, 0x09, 0xFE, 120000, 20 } 168 }; 169 170 /* UTMIP Idle Wait Delay */ 171 static const u8 utmip_idle_wait_delay = 17; 172 173 /* UTMIP Elastic limit */ 174 static const u8 utmip_elastic_limit = 16; 175 176 /* UTMIP High Speed Sync Start Delay */ 177 static const u8 utmip_hs_sync_start_delay = 9; 178 179 struct fdt_usb_controller { 180 /* flag to determine whether controller supports hostpc register */ 181 u32 has_hostpc:1; 182 const unsigned *pll_parameter; 183 }; 184 185 static struct fdt_usb_controller fdt_usb_controllers[USB_CTRL_COUNT] = { 186 { 187 .has_hostpc = 0, 188 .pll_parameter = (const unsigned *)T20_usb_pll, 189 }, 190 { 191 .has_hostpc = 1, 192 .pll_parameter = (const unsigned *)T30_usb_pll, 193 }, 194 { 195 .has_hostpc = 1, 196 .pll_parameter = (const unsigned *)T114_usb_pll, 197 }, 198 { 199 .has_hostpc = 1, 200 .pll_parameter = (const unsigned *)T210_usb_pll, 201 }, 202 }; 203 204 /* 205 * A known hardware issue where Connect Status Change bit of PORTSC register 206 * of USB1 controller will be set after Port Reset. 207 * We have to clear it in order for later device enumeration to proceed. 208 */ 209 static void tegra_ehci_powerup_fixup(struct ehci_ctrl *ctrl, 210 uint32_t *status_reg, uint32_t *reg) 211 { 212 struct fdt_usb *config = ctrl->priv; 213 struct fdt_usb_controller *controller; 214 215 controller = &fdt_usb_controllers[config->type]; 216 mdelay(50); 217 /* This is to avoid PORT_ENABLE bit to be cleared in "ehci-hcd.c". */ 218 if (controller->has_hostpc) 219 *reg |= EHCI_PS_PE; 220 221 if (!config->has_legacy_mode) 222 return; 223 /* For EHCI_PS_CSC to be cleared in ehci_hcd.c */ 224 if (ehci_readl(status_reg) & EHCI_PS_CSC) 225 *reg |= EHCI_PS_CSC; 226 } 227 228 static void tegra_ehci_set_usbmode(struct ehci_ctrl *ctrl) 229 { 230 struct fdt_usb *config = ctrl->priv; 231 struct usb_ctlr *usbctlr; 232 uint32_t tmp; 233 234 usbctlr = config->reg; 235 236 tmp = ehci_readl(&usbctlr->usb_mode); 237 tmp |= USBMODE_CM_HC; 238 ehci_writel(&usbctlr->usb_mode, tmp); 239 } 240 241 static int tegra_ehci_get_port_speed(struct ehci_ctrl *ctrl, uint32_t reg) 242 { 243 struct fdt_usb *config = ctrl->priv; 244 struct fdt_usb_controller *controller; 245 uint32_t tmp; 246 uint32_t *reg_ptr; 247 248 controller = &fdt_usb_controllers[config->type]; 249 if (controller->has_hostpc) { 250 reg_ptr = (uint32_t *)((u8 *)&ctrl->hcor->or_usbcmd + 251 HOSTPC1_DEVLC); 252 tmp = ehci_readl(reg_ptr); 253 return HOSTPC1_PSPD(tmp); 254 } else 255 return PORTSC_PSPD(reg); 256 } 257 258 /* Set up VBUS for host/device mode */ 259 static void set_up_vbus(struct fdt_usb *config, enum usb_init_type init) 260 { 261 /* 262 * If we are an OTG port initializing in host mode, 263 * check if remote host is driving VBus and bail out in this case. 264 */ 265 if (init == USB_INIT_HOST && 266 config->dr_mode == DR_MODE_OTG && 267 (readl(&config->reg->phy_vbus_sensors) & VBUS_VLD_STS)) { 268 printf("tegrausb: VBUS input active; not enabling as host\n"); 269 return; 270 } 271 272 if (dm_gpio_is_valid(&config->vbus_gpio)) { 273 int vbus_value; 274 275 vbus_value = (init == USB_INIT_HOST); 276 dm_gpio_set_value(&config->vbus_gpio, vbus_value); 277 278 debug("set_up_vbus: GPIO %d %d\n", 279 gpio_get_number(&config->vbus_gpio), vbus_value); 280 } 281 } 282 283 static void usbf_reset_controller(struct fdt_usb *config, 284 struct usb_ctlr *usbctlr) 285 { 286 /* Reset the USB controller with 2us delay */ 287 reset_periph(config->periph_id, 2); 288 289 /* 290 * Set USB1_NO_LEGACY_MODE to 1, Registers are accessible under 291 * base address 292 */ 293 if (config->has_legacy_mode) 294 setbits_le32(&usbctlr->usb1_legacy_ctrl, USB1_NO_LEGACY_MODE); 295 296 /* Put UTMIP1/3 in reset */ 297 setbits_le32(&usbctlr->susp_ctrl, UTMIP_RESET); 298 299 /* Enable the UTMIP PHY */ 300 if (config->utmi) 301 setbits_le32(&usbctlr->susp_ctrl, UTMIP_PHY_ENB); 302 } 303 304 static const unsigned *get_pll_timing(struct fdt_usb_controller *controller) 305 { 306 const unsigned *timing; 307 308 timing = controller->pll_parameter + 309 clock_get_osc_freq() * PARAM_COUNT; 310 311 return timing; 312 } 313 314 /* select the PHY to use with a USB controller */ 315 static void init_phy_mux(struct fdt_usb *config, uint pts, 316 enum usb_init_type init) 317 { 318 struct usb_ctlr *usbctlr = config->reg; 319 320 #if defined(CONFIG_TEGRA20) 321 if (config->periph_id == PERIPH_ID_USBD) { 322 clrsetbits_le32(&usbctlr->port_sc1, PTS1_MASK, 323 pts << PTS1_SHIFT); 324 clrbits_le32(&usbctlr->port_sc1, STS1); 325 } else { 326 clrsetbits_le32(&usbctlr->port_sc1, PTS_MASK, 327 pts << PTS_SHIFT); 328 clrbits_le32(&usbctlr->port_sc1, STS); 329 } 330 #else 331 /* Set to Host mode (if applicable) after Controller Reset was done */ 332 clrsetbits_le32(&usbctlr->usb_mode, USBMODE_CM_HC, 333 (init == USB_INIT_HOST) ? USBMODE_CM_HC : 0); 334 /* 335 * Select PHY interface after setting host mode. 336 * For device mode, the ordering requirement is not an issue, since 337 * only the first USB controller supports device mode, and that USB 338 * controller can only talk to a UTMI PHY, so the PHY selection is 339 * already made at reset time, so this write is a no-op. 340 */ 341 clrsetbits_le32(&usbctlr->hostpc1_devlc, PTS_MASK, 342 pts << PTS_SHIFT); 343 clrbits_le32(&usbctlr->hostpc1_devlc, STS); 344 #endif 345 } 346 347 /* set up the UTMI USB controller with the parameters provided */ 348 static int init_utmi_usb_controller(struct fdt_usb *config, 349 enum usb_init_type init) 350 { 351 struct fdt_usb_controller *controller; 352 u32 b_sess_valid_mask, val; 353 int loop_count; 354 const unsigned *timing; 355 struct usb_ctlr *usbctlr = config->reg; 356 struct clk_rst_ctlr *clkrst; 357 struct usb_ctlr *usb1ctlr; 358 359 clock_enable(config->periph_id); 360 361 /* Reset the usb controller */ 362 usbf_reset_controller(config, usbctlr); 363 364 /* Stop crystal clock by setting UTMIP_PHY_XTAL_CLOCKEN low */ 365 clrbits_le32(&usbctlr->utmip_misc_cfg1, UTMIP_PHY_XTAL_CLOCKEN); 366 367 /* Follow the crystal clock disable by >100ns delay */ 368 udelay(1); 369 370 b_sess_valid_mask = (VBUS_B_SESS_VLD_SW_VALUE | VBUS_B_SESS_VLD_SW_EN); 371 clrsetbits_le32(&usbctlr->phy_vbus_sensors, b_sess_valid_mask, 372 (init == USB_INIT_DEVICE) ? b_sess_valid_mask : 0); 373 374 /* 375 * To Use the A Session Valid for cable detection logic, VBUS_WAKEUP 376 * mux must be switched to actually use a_sess_vld threshold. 377 */ 378 if (config->dr_mode == DR_MODE_OTG && 379 dm_gpio_is_valid(&config->vbus_gpio)) 380 clrsetbits_le32(&usbctlr->usb1_legacy_ctrl, 381 VBUS_SENSE_CTL_MASK, 382 VBUS_SENSE_CTL_A_SESS_VLD << VBUS_SENSE_CTL_SHIFT); 383 384 controller = &fdt_usb_controllers[config->type]; 385 debug("controller=%p, type=%d\n", controller, config->type); 386 387 /* 388 * PLL Delay CONFIGURATION settings. The following parameters control 389 * the bring up of the plls. 390 */ 391 timing = get_pll_timing(controller); 392 393 if (!controller->has_hostpc) { 394 val = readl(&usbctlr->utmip_misc_cfg1); 395 clrsetbits_le32(&val, UTMIP_PLLU_STABLE_COUNT_MASK, 396 timing[PARAM_STABLE_COUNT] << 397 UTMIP_PLLU_STABLE_COUNT_SHIFT); 398 clrsetbits_le32(&val, UTMIP_PLL_ACTIVE_DLY_COUNT_MASK, 399 timing[PARAM_ACTIVE_DELAY_COUNT] << 400 UTMIP_PLL_ACTIVE_DLY_COUNT_SHIFT); 401 writel(val, &usbctlr->utmip_misc_cfg1); 402 403 /* Set PLL enable delay count and crystal frequency count */ 404 val = readl(&usbctlr->utmip_pll_cfg1); 405 clrsetbits_le32(&val, UTMIP_PLLU_ENABLE_DLY_COUNT_MASK, 406 timing[PARAM_ENABLE_DELAY_COUNT] << 407 UTMIP_PLLU_ENABLE_DLY_COUNT_SHIFT); 408 clrsetbits_le32(&val, UTMIP_XTAL_FREQ_COUNT_MASK, 409 timing[PARAM_XTAL_FREQ_COUNT] << 410 UTMIP_XTAL_FREQ_COUNT_SHIFT); 411 writel(val, &usbctlr->utmip_pll_cfg1); 412 } else { 413 clkrst = (struct clk_rst_ctlr *)NV_PA_CLK_RST_BASE; 414 415 val = readl(&clkrst->crc_utmip_pll_cfg2); 416 clrsetbits_le32(&val, UTMIP_PLLU_STABLE_COUNT_MASK, 417 timing[PARAM_STABLE_COUNT] << 418 UTMIP_PLLU_STABLE_COUNT_SHIFT); 419 clrsetbits_le32(&val, UTMIP_PLL_ACTIVE_DLY_COUNT_MASK, 420 timing[PARAM_ACTIVE_DELAY_COUNT] << 421 UTMIP_PLL_ACTIVE_DLY_COUNT_SHIFT); 422 writel(val, &clkrst->crc_utmip_pll_cfg2); 423 424 /* Set PLL enable delay count and crystal frequency count */ 425 val = readl(&clkrst->crc_utmip_pll_cfg1); 426 clrsetbits_le32(&val, UTMIP_PLLU_ENABLE_DLY_COUNT_MASK, 427 timing[PARAM_ENABLE_DELAY_COUNT] << 428 UTMIP_PLLU_ENABLE_DLY_COUNT_SHIFT); 429 clrsetbits_le32(&val, UTMIP_XTAL_FREQ_COUNT_MASK, 430 timing[PARAM_XTAL_FREQ_COUNT] << 431 UTMIP_XTAL_FREQ_COUNT_SHIFT); 432 writel(val, &clkrst->crc_utmip_pll_cfg1); 433 434 /* Disable Power Down state for PLL */ 435 clrbits_le32(&clkrst->crc_utmip_pll_cfg1, 436 PLLU_POWERDOWN | PLL_ENABLE_POWERDOWN | 437 PLL_ACTIVE_POWERDOWN); 438 439 /* Recommended PHY settings for EYE diagram */ 440 val = readl(&usbctlr->utmip_xcvr_cfg0); 441 clrsetbits_le32(&val, UTMIP_XCVR_SETUP_MASK, 442 0x4 << UTMIP_XCVR_SETUP_SHIFT); 443 clrsetbits_le32(&val, UTMIP_XCVR_SETUP_MSB_MASK, 444 0x3 << UTMIP_XCVR_SETUP_MSB_SHIFT); 445 clrsetbits_le32(&val, UTMIP_XCVR_HSSLEW_MSB_MASK, 446 0x8 << UTMIP_XCVR_HSSLEW_MSB_SHIFT); 447 writel(val, &usbctlr->utmip_xcvr_cfg0); 448 clrsetbits_le32(&usbctlr->utmip_xcvr_cfg1, 449 UTMIP_XCVR_TERM_RANGE_ADJ_MASK, 450 0x7 << UTMIP_XCVR_TERM_RANGE_ADJ_SHIFT); 451 452 /* Some registers can be controlled from USB1 only. */ 453 if (config->periph_id != PERIPH_ID_USBD) { 454 clock_enable(PERIPH_ID_USBD); 455 /* Disable Reset if in Reset state */ 456 reset_set_enable(PERIPH_ID_USBD, 0); 457 } 458 usb1ctlr = (struct usb_ctlr *) 459 ((unsigned long)config->reg & USB1_ADDR_MASK); 460 val = readl(&usb1ctlr->utmip_bias_cfg0); 461 setbits_le32(&val, UTMIP_HSDISCON_LEVEL_MSB); 462 clrsetbits_le32(&val, UTMIP_HSDISCON_LEVEL_MASK, 463 0x1 << UTMIP_HSDISCON_LEVEL_SHIFT); 464 clrsetbits_le32(&val, UTMIP_HSSQUELCH_LEVEL_MASK, 465 0x2 << UTMIP_HSSQUELCH_LEVEL_SHIFT); 466 writel(val, &usb1ctlr->utmip_bias_cfg0); 467 468 /* Miscellaneous setting mentioned in Programming Guide */ 469 clrbits_le32(&usbctlr->utmip_misc_cfg0, 470 UTMIP_SUSPEND_EXIT_ON_EDGE); 471 } 472 473 /* Setting the tracking length time */ 474 clrsetbits_le32(&usbctlr->utmip_bias_cfg1, 475 UTMIP_BIAS_PDTRK_COUNT_MASK, 476 timing[PARAM_BIAS_TIME] << UTMIP_BIAS_PDTRK_COUNT_SHIFT); 477 478 /* Program debounce time for VBUS to become valid */ 479 clrsetbits_le32(&usbctlr->utmip_debounce_cfg0, 480 UTMIP_DEBOUNCE_CFG0_MASK, 481 timing[PARAM_DEBOUNCE_A_TIME] << UTMIP_DEBOUNCE_CFG0_SHIFT); 482 483 if (timing[PARAM_DEBOUNCE_A_TIME] > 0xFFFF) { 484 clrsetbits_le32(&usbctlr->utmip_debounce_cfg0, 485 UTMIP_DEBOUNCE_CFG0_MASK, 486 (timing[PARAM_DEBOUNCE_A_TIME] >> 1) 487 << UTMIP_DEBOUNCE_CFG0_SHIFT); 488 clrsetbits_le32(&usbctlr->utmip_bias_cfg1, 489 UTMIP_BIAS_DEBOUNCE_TIMESCALE_MASK, 490 1 << UTMIP_BIAS_DEBOUNCE_TIMESCALE_SHIFT); 491 } 492 493 setbits_le32(&usbctlr->utmip_tx_cfg0, UTMIP_FS_PREAMBLE_J); 494 495 /* Disable battery charge enabling bit */ 496 setbits_le32(&usbctlr->utmip_bat_chrg_cfg0, UTMIP_PD_CHRG); 497 498 clrbits_le32(&usbctlr->utmip_xcvr_cfg0, UTMIP_XCVR_LSBIAS_SE); 499 setbits_le32(&usbctlr->utmip_spare_cfg0, FUSE_SETUP_SEL); 500 501 /* 502 * Configure the UTMIP_IDLE_WAIT and UTMIP_ELASTIC_LIMIT 503 * Setting these fields, together with default values of the 504 * other fields, results in programming the registers below as 505 * follows: 506 * UTMIP_HSRX_CFG0 = 0x9168c000 507 * UTMIP_HSRX_CFG1 = 0x13 508 */ 509 510 /* Set PLL enable delay count and Crystal frequency count */ 511 val = readl(&usbctlr->utmip_hsrx_cfg0); 512 clrsetbits_le32(&val, UTMIP_IDLE_WAIT_MASK, 513 utmip_idle_wait_delay << UTMIP_IDLE_WAIT_SHIFT); 514 clrsetbits_le32(&val, UTMIP_ELASTIC_LIMIT_MASK, 515 utmip_elastic_limit << UTMIP_ELASTIC_LIMIT_SHIFT); 516 writel(val, &usbctlr->utmip_hsrx_cfg0); 517 518 /* Configure the UTMIP_HS_SYNC_START_DLY */ 519 clrsetbits_le32(&usbctlr->utmip_hsrx_cfg1, 520 UTMIP_HS_SYNC_START_DLY_MASK, 521 utmip_hs_sync_start_delay << UTMIP_HS_SYNC_START_DLY_SHIFT); 522 523 /* Preceed the crystal clock disable by >100ns delay. */ 524 udelay(1); 525 526 /* Resuscitate crystal clock by setting UTMIP_PHY_XTAL_CLOCKEN */ 527 setbits_le32(&usbctlr->utmip_misc_cfg1, UTMIP_PHY_XTAL_CLOCKEN); 528 529 if (controller->has_hostpc) { 530 if (config->periph_id == PERIPH_ID_USBD) 531 clrbits_le32(&clkrst->crc_utmip_pll_cfg2, 532 UTMIP_FORCE_PD_SAMP_A_POWERDOWN); 533 if (config->periph_id == PERIPH_ID_USB2) 534 clrbits_le32(&clkrst->crc_utmip_pll_cfg2, 535 UTMIP_FORCE_PD_SAMP_B_POWERDOWN); 536 if (config->periph_id == PERIPH_ID_USB3) 537 clrbits_le32(&clkrst->crc_utmip_pll_cfg2, 538 UTMIP_FORCE_PD_SAMP_C_POWERDOWN); 539 } 540 /* Finished the per-controller init. */ 541 542 /* De-assert UTMIP_RESET to bring out of reset. */ 543 clrbits_le32(&usbctlr->susp_ctrl, UTMIP_RESET); 544 545 /* Wait for the phy clock to become valid in 100 ms */ 546 for (loop_count = 100000; loop_count != 0; loop_count--) { 547 if (readl(&usbctlr->susp_ctrl) & USB_PHY_CLK_VALID) 548 break; 549 udelay(1); 550 } 551 if (!loop_count) 552 return -ETIMEDOUT; 553 554 /* Disable ICUSB FS/LS transceiver */ 555 clrbits_le32(&usbctlr->icusb_ctrl, IC_ENB1); 556 557 /* Select UTMI parallel interface */ 558 init_phy_mux(config, PTS_UTMI, init); 559 560 /* Deassert power down state */ 561 clrbits_le32(&usbctlr->utmip_xcvr_cfg0, UTMIP_FORCE_PD_POWERDOWN | 562 UTMIP_FORCE_PD2_POWERDOWN | UTMIP_FORCE_PDZI_POWERDOWN); 563 clrbits_le32(&usbctlr->utmip_xcvr_cfg1, UTMIP_FORCE_PDDISC_POWERDOWN | 564 UTMIP_FORCE_PDCHRP_POWERDOWN | UTMIP_FORCE_PDDR_POWERDOWN); 565 566 if (controller->has_hostpc) { 567 /* 568 * BIAS Pad Power Down is common among all 3 USB 569 * controllers and can be controlled from USB1 only. 570 */ 571 usb1ctlr = (struct usb_ctlr *) 572 ((unsigned long)config->reg & USB1_ADDR_MASK); 573 clrbits_le32(&usb1ctlr->utmip_bias_cfg0, UTMIP_BIASPD); 574 udelay(25); 575 clrbits_le32(&usb1ctlr->utmip_bias_cfg1, 576 UTMIP_FORCE_PDTRK_POWERDOWN); 577 } 578 return 0; 579 } 580 581 #ifdef CONFIG_USB_ULPI 582 /* if board file does not set a ULPI reference frequency we default to 24MHz */ 583 #ifndef CONFIG_ULPI_REF_CLK 584 #define CONFIG_ULPI_REF_CLK 24000000 585 #endif 586 587 /* set up the ULPI USB controller with the parameters provided */ 588 static int init_ulpi_usb_controller(struct fdt_usb *config, 589 enum usb_init_type init) 590 { 591 u32 val; 592 int loop_count; 593 struct ulpi_viewport ulpi_vp; 594 struct usb_ctlr *usbctlr = config->reg; 595 int ret; 596 597 /* set up ULPI reference clock on pllp_out4 */ 598 clock_enable(PERIPH_ID_DEV2_OUT); 599 clock_set_pllout(CLOCK_ID_PERIPH, PLL_OUT4, CONFIG_ULPI_REF_CLK); 600 601 /* reset ULPI phy */ 602 if (dm_gpio_is_valid(&config->phy_reset_gpio)) { 603 /* 604 * This GPIO is typically active-low, and marked as such in 605 * device tree. dm_gpio_set_value() takes this into account 606 * and inverts the value we pass here if required. In other 607 * words, this first call logically asserts the reset signal, 608 * which typically results in driving the physical GPIO low, 609 * and the second call logically de-asserts the reset signal, 610 * which typically results in driver the GPIO high. 611 */ 612 dm_gpio_set_value(&config->phy_reset_gpio, 1); 613 mdelay(5); 614 dm_gpio_set_value(&config->phy_reset_gpio, 0); 615 } 616 617 /* Reset the usb controller */ 618 clock_enable(config->periph_id); 619 usbf_reset_controller(config, usbctlr); 620 621 /* enable pinmux bypass */ 622 setbits_le32(&usbctlr->ulpi_timing_ctrl_0, 623 ULPI_CLKOUT_PINMUX_BYP | ULPI_OUTPUT_PINMUX_BYP); 624 625 /* Select ULPI parallel interface */ 626 init_phy_mux(config, PTS_ULPI, init); 627 628 /* enable ULPI transceiver */ 629 setbits_le32(&usbctlr->susp_ctrl, ULPI_PHY_ENB); 630 631 /* configure ULPI transceiver timings */ 632 val = 0; 633 writel(val, &usbctlr->ulpi_timing_ctrl_1); 634 635 val |= ULPI_DATA_TRIMMER_SEL(4); 636 val |= ULPI_STPDIRNXT_TRIMMER_SEL(4); 637 val |= ULPI_DIR_TRIMMER_SEL(4); 638 writel(val, &usbctlr->ulpi_timing_ctrl_1); 639 udelay(10); 640 641 val |= ULPI_DATA_TRIMMER_LOAD; 642 val |= ULPI_STPDIRNXT_TRIMMER_LOAD; 643 val |= ULPI_DIR_TRIMMER_LOAD; 644 writel(val, &usbctlr->ulpi_timing_ctrl_1); 645 646 /* set up phy for host operation with external vbus supply */ 647 ulpi_vp.port_num = 0; 648 ulpi_vp.viewport_addr = (u32)&usbctlr->ulpi_viewport; 649 650 ret = ulpi_init(&ulpi_vp); 651 if (ret) { 652 printf("Tegra ULPI viewport init failed\n"); 653 return ret; 654 } 655 656 ulpi_set_vbus(&ulpi_vp, 1, 1); 657 ulpi_set_vbus_indicator(&ulpi_vp, 1, 1, 0); 658 659 /* enable wakeup events */ 660 setbits_le32(&usbctlr->port_sc1, WKCN | WKDS | WKOC); 661 662 /* Enable and wait for the phy clock to become valid in 100 ms */ 663 setbits_le32(&usbctlr->susp_ctrl, USB_SUSP_CLR); 664 for (loop_count = 100000; loop_count != 0; loop_count--) { 665 if (readl(&usbctlr->susp_ctrl) & USB_PHY_CLK_VALID) 666 break; 667 udelay(1); 668 } 669 if (!loop_count) 670 return -ETIMEDOUT; 671 clrbits_le32(&usbctlr->susp_ctrl, USB_SUSP_CLR); 672 673 return 0; 674 } 675 #else 676 static int init_ulpi_usb_controller(struct fdt_usb *config, 677 enum usb_init_type init) 678 { 679 printf("No code to set up ULPI controller, please enable" 680 "CONFIG_USB_ULPI and CONFIG_USB_ULPI_VIEWPORT"); 681 return -ENOSYS; 682 } 683 #endif 684 685 static void config_clock(const u32 timing[]) 686 { 687 debug("%s: DIVM = %d, DIVN = %d, DIVP = %d, cpcon/lfcon = %d/%d\n", 688 __func__, timing[PARAM_DIVM], timing[PARAM_DIVN], 689 timing[PARAM_DIVP], timing[PARAM_CPCON], timing[PARAM_LFCON]); 690 691 clock_start_pll(CLOCK_ID_USB, 692 timing[PARAM_DIVM], timing[PARAM_DIVN], timing[PARAM_DIVP], 693 timing[PARAM_CPCON], timing[PARAM_LFCON]); 694 } 695 696 static int fdt_decode_usb(struct udevice *dev, struct fdt_usb *config) 697 { 698 const void *blob = gd->fdt_blob; 699 int node = dev_of_offset(dev); 700 const char *phy, *mode; 701 702 config->reg = (struct usb_ctlr *)dev_get_addr(dev); 703 mode = fdt_getprop(blob, node, "dr_mode", NULL); 704 if (mode) { 705 if (0 == strcmp(mode, "host")) 706 config->dr_mode = DR_MODE_HOST; 707 else if (0 == strcmp(mode, "peripheral")) 708 config->dr_mode = DR_MODE_DEVICE; 709 else if (0 == strcmp(mode, "otg")) 710 config->dr_mode = DR_MODE_OTG; 711 else { 712 debug("%s: Cannot decode dr_mode '%s'\n", __func__, 713 mode); 714 return -EINVAL; 715 } 716 } else { 717 config->dr_mode = DR_MODE_HOST; 718 } 719 720 phy = fdt_getprop(blob, node, "phy_type", NULL); 721 config->utmi = phy && 0 == strcmp("utmi", phy); 722 config->ulpi = phy && 0 == strcmp("ulpi", phy); 723 config->enabled = fdtdec_get_is_enabled(blob, node); 724 config->has_legacy_mode = fdtdec_get_bool(blob, node, 725 "nvidia,has-legacy-mode"); 726 config->periph_id = clock_decode_periph_id(blob, node); 727 if (config->periph_id == PERIPH_ID_NONE) { 728 debug("%s: Missing/invalid peripheral ID\n", __func__); 729 return -EINVAL; 730 } 731 gpio_request_by_name_nodev(blob, node, "nvidia,vbus-gpio", 0, 732 &config->vbus_gpio, GPIOD_IS_OUT); 733 gpio_request_by_name_nodev(blob, node, "nvidia,phy-reset-gpio", 0, 734 &config->phy_reset_gpio, GPIOD_IS_OUT); 735 debug("enabled=%d, legacy_mode=%d, utmi=%d, ulpi=%d, periph_id=%d, " 736 "vbus=%d, phy_reset=%d, dr_mode=%d\n", 737 config->enabled, config->has_legacy_mode, config->utmi, 738 config->ulpi, config->periph_id, 739 gpio_get_number(&config->vbus_gpio), 740 gpio_get_number(&config->phy_reset_gpio), config->dr_mode); 741 742 return 0; 743 } 744 745 int usb_common_init(struct fdt_usb *config, enum usb_init_type init) 746 { 747 int ret = 0; 748 749 switch (init) { 750 case USB_INIT_HOST: 751 switch (config->dr_mode) { 752 case DR_MODE_HOST: 753 case DR_MODE_OTG: 754 break; 755 default: 756 printf("tegrausb: Invalid dr_mode %d for host mode\n", 757 config->dr_mode); 758 return -1; 759 } 760 break; 761 case USB_INIT_DEVICE: 762 if (config->periph_id != PERIPH_ID_USBD) { 763 printf("tegrausb: Device mode only supported on first USB controller\n"); 764 return -1; 765 } 766 if (!config->utmi) { 767 printf("tegrausb: Device mode only supported with UTMI PHY\n"); 768 return -1; 769 } 770 switch (config->dr_mode) { 771 case DR_MODE_DEVICE: 772 case DR_MODE_OTG: 773 break; 774 default: 775 printf("tegrausb: Invalid dr_mode %d for device mode\n", 776 config->dr_mode); 777 return -1; 778 } 779 break; 780 default: 781 printf("tegrausb: Unknown USB_INIT_* %d\n", init); 782 return -1; 783 } 784 785 debug("%d, %d\n", config->utmi, config->ulpi); 786 if (config->utmi) 787 ret = init_utmi_usb_controller(config, init); 788 else if (config->ulpi) 789 ret = init_ulpi_usb_controller(config, init); 790 if (ret) 791 return ret; 792 793 set_up_vbus(config, init); 794 795 config->init_type = init; 796 797 return 0; 798 } 799 800 void usb_common_uninit(struct fdt_usb *priv) 801 { 802 struct usb_ctlr *usbctlr; 803 804 usbctlr = priv->reg; 805 806 /* Stop controller */ 807 writel(0, &usbctlr->usb_cmd); 808 udelay(1000); 809 810 /* Initiate controller reset */ 811 writel(2, &usbctlr->usb_cmd); 812 udelay(1000); 813 } 814 815 static const struct ehci_ops tegra_ehci_ops = { 816 .set_usb_mode = tegra_ehci_set_usbmode, 817 .get_port_speed = tegra_ehci_get_port_speed, 818 .powerup_fixup = tegra_ehci_powerup_fixup, 819 }; 820 821 static int ehci_usb_ofdata_to_platdata(struct udevice *dev) 822 { 823 struct fdt_usb *priv = dev_get_priv(dev); 824 int ret; 825 826 ret = fdt_decode_usb(dev, priv); 827 if (ret) 828 return ret; 829 830 priv->type = dev_get_driver_data(dev); 831 832 return 0; 833 } 834 835 static int ehci_usb_probe(struct udevice *dev) 836 { 837 struct usb_platdata *plat = dev_get_platdata(dev); 838 struct fdt_usb *priv = dev_get_priv(dev); 839 struct ehci_hccr *hccr; 840 struct ehci_hcor *hcor; 841 static bool clk_done; 842 int ret; 843 844 ret = usb_common_init(priv, plat->init_type); 845 if (ret) 846 return ret; 847 hccr = (struct ehci_hccr *)&priv->reg->cap_length; 848 hcor = (struct ehci_hcor *)&priv->reg->usb_cmd; 849 if (!clk_done) { 850 config_clock(get_pll_timing(&fdt_usb_controllers[priv->type])); 851 clk_done = true; 852 } 853 854 return ehci_register(dev, hccr, hcor, &tegra_ehci_ops, 0, 855 plat->init_type); 856 } 857 858 static const struct udevice_id ehci_usb_ids[] = { 859 { .compatible = "nvidia,tegra20-ehci", .data = USB_CTLR_T20 }, 860 { .compatible = "nvidia,tegra30-ehci", .data = USB_CTLR_T30 }, 861 { .compatible = "nvidia,tegra114-ehci", .data = USB_CTLR_T114 }, 862 { .compatible = "nvidia,tegra210-ehci", .data = USB_CTLR_T210 }, 863 { } 864 }; 865 866 U_BOOT_DRIVER(usb_ehci) = { 867 .name = "ehci_tegra", 868 .id = UCLASS_USB, 869 .of_match = ehci_usb_ids, 870 .ofdata_to_platdata = ehci_usb_ofdata_to_platdata, 871 .probe = ehci_usb_probe, 872 .remove = ehci_deregister, 873 .ops = &ehci_usb_ops, 874 .platdata_auto_alloc_size = sizeof(struct usb_platdata), 875 .priv_auto_alloc_size = sizeof(struct fdt_usb), 876 .flags = DM_FLAG_ALLOC_PRIV_DMA, 877 }; 878