1 /* 2 * Copyright (c) 2009 Daniel Mack <daniel@caiaq.de> 3 * Copyright (C) 2010 Freescale Semiconductor, Inc. 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 8 #include <common.h> 9 #include <usb.h> 10 #include <errno.h> 11 #include <linux/compiler.h> 12 #include <usb/ehci-fsl.h> 13 #include <asm/io.h> 14 #include <asm/arch/imx-regs.h> 15 #include <asm/arch/clock.h> 16 #include <asm/imx-common/iomux-v3.h> 17 18 #include "ehci.h" 19 20 #define USB_OTGREGS_OFFSET 0x000 21 #define USB_H1REGS_OFFSET 0x200 22 #define USB_H2REGS_OFFSET 0x400 23 #define USB_H3REGS_OFFSET 0x600 24 #define USB_OTHERREGS_OFFSET 0x800 25 26 #define USB_H1_CTRL_OFFSET 0x04 27 28 #define USBPHY_CTRL 0x00000030 29 #define USBPHY_CTRL_SET 0x00000034 30 #define USBPHY_CTRL_CLR 0x00000038 31 #define USBPHY_CTRL_TOG 0x0000003c 32 33 #define USBPHY_PWD 0x00000000 34 #define USBPHY_CTRL_SFTRST 0x80000000 35 #define USBPHY_CTRL_CLKGATE 0x40000000 36 #define USBPHY_CTRL_ENUTMILEVEL3 0x00008000 37 #define USBPHY_CTRL_ENUTMILEVEL2 0x00004000 38 #define USBPHY_CTRL_OTG_ID 0x08000000 39 40 #define ANADIG_USB2_CHRG_DETECT_EN_B 0x00100000 41 #define ANADIG_USB2_CHRG_DETECT_CHK_CHRG_B 0x00080000 42 43 #define ANADIG_USB2_PLL_480_CTRL_BYPASS 0x00010000 44 #define ANADIG_USB2_PLL_480_CTRL_ENABLE 0x00002000 45 #define ANADIG_USB2_PLL_480_CTRL_POWER 0x00001000 46 #define ANADIG_USB2_PLL_480_CTRL_EN_USB_CLKS 0x00000040 47 48 49 #define UCTRL_OVER_CUR_POL (1 << 8) /* OTG Polarity of Overcurrent */ 50 #define UCTRL_OVER_CUR_DIS (1 << 7) /* Disable OTG Overcurrent Detection */ 51 52 /* USBCMD */ 53 #define UCMD_RUN_STOP (1 << 0) /* controller run/stop */ 54 #define UCMD_RESET (1 << 1) /* controller reset */ 55 56 static const unsigned phy_bases[] = { 57 USB_PHY0_BASE_ADDR, 58 USB_PHY1_BASE_ADDR, 59 }; 60 61 static void usb_internal_phy_clock_gate(int index, int on) 62 { 63 void __iomem *phy_reg; 64 65 if (index >= ARRAY_SIZE(phy_bases)) 66 return; 67 68 phy_reg = (void __iomem *)phy_bases[index]; 69 phy_reg += on ? USBPHY_CTRL_CLR : USBPHY_CTRL_SET; 70 __raw_writel(USBPHY_CTRL_CLKGATE, phy_reg); 71 } 72 73 static void usb_power_config(int index) 74 { 75 struct anatop_regs __iomem *anatop = 76 (struct anatop_regs __iomem *)ANATOP_BASE_ADDR; 77 void __iomem *chrg_detect; 78 void __iomem *pll_480_ctrl_clr; 79 void __iomem *pll_480_ctrl_set; 80 81 switch (index) { 82 case 0: 83 chrg_detect = &anatop->usb1_chrg_detect; 84 pll_480_ctrl_clr = &anatop->usb1_pll_480_ctrl_clr; 85 pll_480_ctrl_set = &anatop->usb1_pll_480_ctrl_set; 86 break; 87 case 1: 88 chrg_detect = &anatop->usb2_chrg_detect; 89 pll_480_ctrl_clr = &anatop->usb2_pll_480_ctrl_clr; 90 pll_480_ctrl_set = &anatop->usb2_pll_480_ctrl_set; 91 break; 92 default: 93 return; 94 } 95 /* 96 * Some phy and power's special controls 97 * 1. The external charger detector needs to be disabled 98 * or the signal at DP will be poor 99 * 2. The PLL's power and output to usb 100 * is totally controlled by IC, so the Software only needs 101 * to enable them at initializtion. 102 */ 103 __raw_writel(ANADIG_USB2_CHRG_DETECT_EN_B | 104 ANADIG_USB2_CHRG_DETECT_CHK_CHRG_B, 105 chrg_detect); 106 107 __raw_writel(ANADIG_USB2_PLL_480_CTRL_BYPASS, 108 pll_480_ctrl_clr); 109 110 __raw_writel(ANADIG_USB2_PLL_480_CTRL_ENABLE | 111 ANADIG_USB2_PLL_480_CTRL_POWER | 112 ANADIG_USB2_PLL_480_CTRL_EN_USB_CLKS, 113 pll_480_ctrl_set); 114 } 115 116 /* Return 0 : host node, <>0 : device mode */ 117 static int usb_phy_enable(int index, struct usb_ehci *ehci) 118 { 119 void __iomem *phy_reg; 120 void __iomem *phy_ctrl; 121 void __iomem *usb_cmd; 122 u32 val; 123 124 if (index >= ARRAY_SIZE(phy_bases)) 125 return 0; 126 127 phy_reg = (void __iomem *)phy_bases[index]; 128 phy_ctrl = (void __iomem *)(phy_reg + USBPHY_CTRL); 129 usb_cmd = (void __iomem *)&ehci->usbcmd; 130 131 /* Stop then Reset */ 132 val = __raw_readl(usb_cmd); 133 val &= ~UCMD_RUN_STOP; 134 __raw_writel(val, usb_cmd); 135 while (__raw_readl(usb_cmd) & UCMD_RUN_STOP) 136 ; 137 138 val = __raw_readl(usb_cmd); 139 val |= UCMD_RESET; 140 __raw_writel(val, usb_cmd); 141 while (__raw_readl(usb_cmd) & UCMD_RESET) 142 ; 143 144 /* Reset USBPHY module */ 145 val = __raw_readl(phy_ctrl); 146 val |= USBPHY_CTRL_SFTRST; 147 __raw_writel(val, phy_ctrl); 148 udelay(10); 149 150 /* Remove CLKGATE and SFTRST */ 151 val = __raw_readl(phy_ctrl); 152 val &= ~(USBPHY_CTRL_CLKGATE | USBPHY_CTRL_SFTRST); 153 __raw_writel(val, phy_ctrl); 154 udelay(10); 155 156 /* Power up the PHY */ 157 __raw_writel(0, phy_reg + USBPHY_PWD); 158 /* enable FS/LS device */ 159 val = __raw_readl(phy_ctrl); 160 val |= (USBPHY_CTRL_ENUTMILEVEL2 | USBPHY_CTRL_ENUTMILEVEL3); 161 __raw_writel(val, phy_ctrl); 162 163 return 0; 164 } 165 166 /* Base address for this IP block is 0x02184800 */ 167 struct usbnc_regs { 168 u32 ctrl[4]; /* otg/host1-3 */ 169 u32 uh2_hsic_ctrl; 170 u32 uh3_hsic_ctrl; 171 u32 otg_phy_ctrl_0; 172 u32 uh1_phy_ctrl_0; 173 }; 174 175 static void usb_oc_config(int index) 176 { 177 struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR + 178 USB_OTHERREGS_OFFSET); 179 void __iomem *ctrl = (void __iomem *)(&usbnc->ctrl[index]); 180 u32 val; 181 182 val = __raw_readl(ctrl); 183 #if CONFIG_MACH_TYPE == MACH_TYPE_MX6Q_ARM2 184 /* mx6qarm2 seems to required a different setting*/ 185 val &= ~UCTRL_OVER_CUR_POL; 186 #else 187 val |= UCTRL_OVER_CUR_POL; 188 #endif 189 __raw_writel(val, ctrl); 190 191 val = __raw_readl(ctrl); 192 val |= UCTRL_OVER_CUR_DIS; 193 __raw_writel(val, ctrl); 194 } 195 196 int usb_phy_mode(int port) 197 { 198 void __iomem *phy_reg; 199 void __iomem *phy_ctrl; 200 u32 val; 201 202 phy_reg = (void __iomem *)phy_bases[port]; 203 phy_ctrl = (void __iomem *)(phy_reg + USBPHY_CTRL); 204 205 val = __raw_readl(phy_ctrl); 206 207 if (val & USBPHY_CTRL_OTG_ID) 208 return USB_INIT_DEVICE; 209 else 210 return USB_INIT_HOST; 211 } 212 213 int __weak board_usb_phy_mode(int port) 214 { 215 return usb_phy_mode(port); 216 } 217 218 int __weak board_ehci_hcd_init(int port) 219 { 220 return 0; 221 } 222 223 int __weak board_ehci_power(int port, int on) 224 { 225 return 0; 226 } 227 228 int ehci_hcd_init(int index, enum usb_init_type init, 229 struct ehci_hccr **hccr, struct ehci_hcor **hcor) 230 { 231 enum usb_init_type type; 232 struct usb_ehci *ehci = (struct usb_ehci *)(USB_BASE_ADDR + 233 (0x200 * index)); 234 235 if (index > 3) 236 return -EINVAL; 237 enable_usboh3_clk(1); 238 mdelay(1); 239 240 /* Do board specific initialization */ 241 board_ehci_hcd_init(index); 242 243 usb_power_config(index); 244 usb_oc_config(index); 245 usb_internal_phy_clock_gate(index, 1); 246 usb_phy_enable(index, ehci); 247 type = board_usb_phy_mode(index); 248 249 *hccr = (struct ehci_hccr *)((uint32_t)&ehci->caplength); 250 *hcor = (struct ehci_hcor *)((uint32_t)*hccr + 251 HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase))); 252 253 if ((type == init) || (type == USB_INIT_DEVICE)) 254 board_ehci_power(index, (type == USB_INIT_DEVICE) ? 0 : 1); 255 if (type != init) 256 return -ENODEV; 257 if (type == USB_INIT_DEVICE) 258 return 0; 259 setbits_le32(&ehci->usbmode, CM_HOST); 260 __raw_writel(CONFIG_MXC_USB_PORTSC, &ehci->portsc); 261 setbits_le32(&ehci->portsc, USB_EN); 262 263 mdelay(10); 264 265 return 0; 266 } 267 268 int ehci_hcd_stop(int index) 269 { 270 return 0; 271 } 272