1 /* 2 * Copyright (c) 2009 Daniel Mack <daniel@caiaq.de> 3 * Copyright (C) 2010 Freescale Semiconductor, Inc. 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 8 #include <common.h> 9 #include <usb.h> 10 #include <errno.h> 11 #include <linux/compiler.h> 12 #include <usb/ehci-ci.h> 13 #include <asm/io.h> 14 #include <asm/arch/imx-regs.h> 15 #include <asm/arch/clock.h> 16 17 #include "ehci.h" 18 19 #define MX5_USBOTHER_REGS_OFFSET 0x800 20 21 22 #define MXC_OTG_OFFSET 0 23 #define MXC_H1_OFFSET 0x200 24 #define MXC_H2_OFFSET 0x400 25 #define MXC_H3_OFFSET 0x600 26 27 #define MXC_USBCTRL_OFFSET 0 28 #define MXC_USB_PHY_CTR_FUNC_OFFSET 0x8 29 #define MXC_USB_PHY_CTR_FUNC2_OFFSET 0xc 30 #define MXC_USB_CTRL_1_OFFSET 0x10 31 #define MXC_USBH2CTRL_OFFSET 0x14 32 #define MXC_USBH3CTRL_OFFSET 0x18 33 34 /* USB_CTRL */ 35 /* OTG wakeup intr enable */ 36 #define MXC_OTG_UCTRL_OWIE_BIT (1 << 27) 37 /* OTG power mask */ 38 #define MXC_OTG_UCTRL_OPM_BIT (1 << 24) 39 /* OTG power pin polarity */ 40 #define MXC_OTG_UCTRL_O_PWR_POL_BIT (1 << 24) 41 /* Host1 ULPI interrupt enable */ 42 #define MXC_H1_UCTRL_H1UIE_BIT (1 << 12) 43 /* HOST1 wakeup intr enable */ 44 #define MXC_H1_UCTRL_H1WIE_BIT (1 << 11) 45 /* HOST1 power mask */ 46 #define MXC_H1_UCTRL_H1PM_BIT (1 << 8) 47 /* HOST1 power pin polarity */ 48 #define MXC_H1_UCTRL_H1_PWR_POL_BIT (1 << 8) 49 50 /* USB_PHY_CTRL_FUNC */ 51 /* OTG Polarity of Overcurrent */ 52 #define MXC_OTG_PHYCTRL_OC_POL_BIT (1 << 9) 53 /* OTG Disable Overcurrent Event */ 54 #define MXC_OTG_PHYCTRL_OC_DIS_BIT (1 << 8) 55 /* UH1 Polarity of Overcurrent */ 56 #define MXC_H1_OC_POL_BIT (1 << 6) 57 /* UH1 Disable Overcurrent Event */ 58 #define MXC_H1_OC_DIS_BIT (1 << 5) 59 /* OTG Power Pin Polarity */ 60 #define MXC_OTG_PHYCTRL_PWR_POL_BIT (1 << 3) 61 62 /* USBH2CTRL */ 63 #define MXC_H2_UCTRL_H2_OC_POL_BIT (1 << 31) 64 #define MXC_H2_UCTRL_H2_OC_DIS_BIT (1 << 30) 65 #define MXC_H2_UCTRL_H2UIE_BIT (1 << 8) 66 #define MXC_H2_UCTRL_H2WIE_BIT (1 << 7) 67 #define MXC_H2_UCTRL_H2PM_BIT (1 << 4) 68 #define MXC_H2_UCTRL_H2_PWR_POL_BIT (1 << 4) 69 70 /* USBH3CTRL */ 71 #define MXC_H3_UCTRL_H3_OC_POL_BIT (1 << 31) 72 #define MXC_H3_UCTRL_H3_OC_DIS_BIT (1 << 30) 73 #define MXC_H3_UCTRL_H3UIE_BIT (1 << 8) 74 #define MXC_H3_UCTRL_H3WIE_BIT (1 << 7) 75 #define MXC_H3_UCTRL_H3_PWR_POL_BIT (1 << 4) 76 77 /* USB_CTRL_1 */ 78 #define MXC_USB_CTRL_UH1_EXT_CLK_EN (1 << 25) 79 80 int mxc_set_usbcontrol(int port, unsigned int flags) 81 { 82 unsigned int v; 83 void __iomem *usb_base = (void __iomem *)OTG_BASE_ADDR; 84 void __iomem *usbother_base; 85 int ret = 0; 86 87 usbother_base = usb_base + MX5_USBOTHER_REGS_OFFSET; 88 89 switch (port) { 90 case 0: /* OTG port */ 91 if (flags & MXC_EHCI_INTERNAL_PHY) { 92 v = __raw_readl(usbother_base + 93 MXC_USB_PHY_CTR_FUNC_OFFSET); 94 if (flags & MXC_EHCI_OC_PIN_ACTIVE_LOW) 95 v |= MXC_OTG_PHYCTRL_OC_POL_BIT; 96 else 97 v &= ~MXC_OTG_PHYCTRL_OC_POL_BIT; 98 if (flags & MXC_EHCI_POWER_PINS_ENABLED) 99 /* OC/USBPWR is used */ 100 v &= ~MXC_OTG_PHYCTRL_OC_DIS_BIT; 101 else 102 /* OC/USBPWR is not used */ 103 v |= MXC_OTG_PHYCTRL_OC_DIS_BIT; 104 #ifdef CONFIG_MX51 105 if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH) 106 v |= MXC_OTG_PHYCTRL_PWR_POL_BIT; 107 else 108 v &= ~MXC_OTG_PHYCTRL_PWR_POL_BIT; 109 #endif 110 __raw_writel(v, usbother_base + 111 MXC_USB_PHY_CTR_FUNC_OFFSET); 112 113 v = __raw_readl(usbother_base + MXC_USBCTRL_OFFSET); 114 #ifdef CONFIG_MX51 115 if (flags & MXC_EHCI_POWER_PINS_ENABLED) 116 v &= ~MXC_OTG_UCTRL_OPM_BIT; 117 else 118 v |= MXC_OTG_UCTRL_OPM_BIT; 119 #endif 120 #ifdef CONFIG_MX53 121 if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH) 122 v |= MXC_OTG_UCTRL_O_PWR_POL_BIT; 123 else 124 v &= ~MXC_OTG_UCTRL_O_PWR_POL_BIT; 125 #endif 126 __raw_writel(v, usbother_base + MXC_USBCTRL_OFFSET); 127 } 128 break; 129 case 1: /* Host 1 ULPI */ 130 #ifdef CONFIG_MX51 131 /* The clock for the USBH1 ULPI port will come externally 132 from the PHY. */ 133 v = __raw_readl(usbother_base + MXC_USB_CTRL_1_OFFSET); 134 __raw_writel(v | MXC_USB_CTRL_UH1_EXT_CLK_EN, usbother_base + 135 MXC_USB_CTRL_1_OFFSET); 136 #endif 137 138 v = __raw_readl(usbother_base + MXC_USBCTRL_OFFSET); 139 #ifdef CONFIG_MX51 140 if (flags & MXC_EHCI_POWER_PINS_ENABLED) 141 v &= ~MXC_H1_UCTRL_H1PM_BIT; /* H1 power mask unused */ 142 else 143 v |= MXC_H1_UCTRL_H1PM_BIT; /* H1 power mask used */ 144 #endif 145 #ifdef CONFIG_MX53 146 if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH) 147 v |= MXC_H1_UCTRL_H1_PWR_POL_BIT; 148 else 149 v &= ~MXC_H1_UCTRL_H1_PWR_POL_BIT; 150 #endif 151 __raw_writel(v, usbother_base + MXC_USBCTRL_OFFSET); 152 153 v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC_OFFSET); 154 if (flags & MXC_EHCI_OC_PIN_ACTIVE_LOW) 155 v |= MXC_H1_OC_POL_BIT; 156 else 157 v &= ~MXC_H1_OC_POL_BIT; 158 if (flags & MXC_EHCI_POWER_PINS_ENABLED) 159 v &= ~MXC_H1_OC_DIS_BIT; /* OC is used */ 160 else 161 v |= MXC_H1_OC_DIS_BIT; /* OC is not used */ 162 __raw_writel(v, usbother_base + MXC_USB_PHY_CTR_FUNC_OFFSET); 163 164 break; 165 case 2: /* Host 2 ULPI */ 166 v = __raw_readl(usbother_base + MXC_USBH2CTRL_OFFSET); 167 #ifdef CONFIG_MX51 168 if (flags & MXC_EHCI_POWER_PINS_ENABLED) 169 v &= ~MXC_H2_UCTRL_H2PM_BIT; /* H2 power mask unused */ 170 else 171 v |= MXC_H2_UCTRL_H2PM_BIT; /* H2 power mask used */ 172 #endif 173 #ifdef CONFIG_MX53 174 if (flags & MXC_EHCI_OC_PIN_ACTIVE_LOW) 175 v |= MXC_H2_UCTRL_H2_OC_POL_BIT; 176 else 177 v &= ~MXC_H2_UCTRL_H2_OC_POL_BIT; 178 if (flags & MXC_EHCI_POWER_PINS_ENABLED) 179 v &= ~MXC_H2_UCTRL_H2_OC_DIS_BIT; /* OC is used */ 180 else 181 v |= MXC_H2_UCTRL_H2_OC_DIS_BIT; /* OC is not used */ 182 if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH) 183 v |= MXC_H2_UCTRL_H2_PWR_POL_BIT; 184 else 185 v &= ~MXC_H2_UCTRL_H2_PWR_POL_BIT; 186 #endif 187 __raw_writel(v, usbother_base + MXC_USBH2CTRL_OFFSET); 188 break; 189 #ifdef CONFIG_MX53 190 case 3: /* Host 3 ULPI */ 191 v = __raw_readl(usbother_base + MXC_USBH3CTRL_OFFSET); 192 if (flags & MXC_EHCI_OC_PIN_ACTIVE_LOW) 193 v |= MXC_H3_UCTRL_H3_OC_POL_BIT; 194 else 195 v &= ~MXC_H3_UCTRL_H3_OC_POL_BIT; 196 if (flags & MXC_EHCI_POWER_PINS_ENABLED) 197 v &= ~MXC_H3_UCTRL_H3_OC_DIS_BIT; /* OC is used */ 198 else 199 v |= MXC_H3_UCTRL_H3_OC_DIS_BIT; /* OC is not used */ 200 if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH) 201 v |= MXC_H3_UCTRL_H3_PWR_POL_BIT; 202 else 203 v &= ~MXC_H3_UCTRL_H3_PWR_POL_BIT; 204 __raw_writel(v, usbother_base + MXC_USBH3CTRL_OFFSET); 205 break; 206 #endif 207 } 208 209 return ret; 210 } 211 212 int __weak board_ehci_hcd_init(int port) 213 { 214 return 0; 215 } 216 217 void __weak board_ehci_hcd_postinit(struct usb_ehci *ehci, int port) 218 { 219 } 220 221 __weak void mx5_ehci_powerup_fixup(struct ehci_ctrl *ctrl, uint32_t *status_reg, 222 uint32_t *reg) 223 { 224 mdelay(50); 225 } 226 227 static const struct ehci_ops mx5_ehci_ops = { 228 .powerup_fixup = mx5_ehci_powerup_fixup, 229 }; 230 231 int ehci_hcd_init(int index, enum usb_init_type init, 232 struct ehci_hccr **hccr, struct ehci_hcor **hcor) 233 { 234 struct usb_ehci *ehci; 235 236 /* The only user for this is efikamx-usb */ 237 ehci_set_controller_priv(index, NULL, &mx5_ehci_ops); 238 set_usboh3_clk(); 239 enable_usboh3_clk(true); 240 set_usb_phy_clk(); 241 enable_usb_phy1_clk(true); 242 enable_usb_phy2_clk(true); 243 mdelay(1); 244 245 /* Do board specific initialization */ 246 board_ehci_hcd_init(CONFIG_MXC_USB_PORT); 247 248 ehci = (struct usb_ehci *)(OTG_BASE_ADDR + 249 (0x200 * CONFIG_MXC_USB_PORT)); 250 *hccr = (struct ehci_hccr *)((uint32_t)&ehci->caplength); 251 *hcor = (struct ehci_hcor *)((uint32_t)*hccr + 252 HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase))); 253 setbits_le32(&ehci->usbmode, CM_HOST); 254 255 __raw_writel(CONFIG_MXC_USB_PORTSC, &ehci->portsc); 256 setbits_le32(&ehci->portsc, USB_EN); 257 258 mxc_set_usbcontrol(CONFIG_MXC_USB_PORT, CONFIG_MXC_USB_FLAGS); 259 mdelay(10); 260 261 /* Do board specific post-initialization */ 262 board_ehci_hcd_postinit(ehci, CONFIG_MXC_USB_PORT); 263 264 return 0; 265 } 266 267 int ehci_hcd_stop(int index) 268 { 269 return 0; 270 } 271