1# 2# USB Host Controller Drivers 3# 4comment "USB Host Controller Drivers" 5 6config USB_HOST 7 bool 8 9config USB_XHCI_HCD 10 bool "xHCI HCD (USB 3.0) support" 11 select USB_HOST 12 ---help--- 13 The eXtensible Host Controller Interface (xHCI) is standard for USB 3.0 14 "SuperSpeed" host controller hardware. 15 16if USB_XHCI_HCD 17 18config USB_XHCI_UNIPHIER 19 bool "Support for UniPhier on-chip xHCI USB controller" 20 depends on ARCH_UNIPHIER 21 default y 22 ---help--- 23 Enables support for the on-chip xHCI controller on UniPhier SoCs. 24 25config USB_XHCI_DWC3 26 bool "DesignWare USB3 DRD Core Support" 27 help 28 Say Y or if your system has a Dual Role SuperSpeed 29 USB controller based on the DesignWare USB3 IP Core. 30 31endif # USB_XHCI_HCD 32 33config USB_EHCI_HCD 34 bool "EHCI HCD (USB 2.0) support" 35 select USB_HOST 36 ---help--- 37 The Enhanced Host Controller Interface (EHCI) is standard for USB 2.0 38 "high speed" (480 Mbit/sec, 60 Mbyte/sec) host controller hardware. 39 If your USB host controller supports USB 2.0, you will likely want to 40 configure this Host Controller Driver. 41 42 EHCI controllers are packaged with "companion" host controllers (OHCI 43 or UHCI) to handle USB 1.1 devices connected to root hub ports. Ports 44 will connect to EHCI if the device is high speed, otherwise they 45 connect to a companion controller. If you configure EHCI, you should 46 probably configure the OHCI (for NEC and some other vendors) USB Host 47 Controller Driver or UHCI (for Via motherboards) Host Controller 48 Driver too. 49 50 You may want to read <file:Documentation/usb/ehci.txt>. 51 52config USB_EHCI 53 bool 54 default USB_EHCI_HCD 55 ---help--- 56 TODO: rename after most boards switch to Kconfig 57 58if USB_EHCI_HCD 59 60config USB_EHCI_ATMEL 61 bool "Support for Atmel on-chip EHCI USB controller" 62 depends on ARCH_AT91 63 default y 64 ---help--- 65 Enables support for the on-chip EHCI controller on Atmel chips. 66 67config USB_EHCI_MARVELL 68 bool "Support for MVEBU (AXP / A38x) on-chip EHCI USB controller" 69 depends on ARCH_MVEBU 70 default y 71 ---help--- 72 Enables support for the on-chip EHCI controller on MVEBU SoCs. 73 74config USB_EHCI_MX6 75 bool "Support for i.MX6 on-chip EHCI USB controller" 76 depends on ARCH_MX6 77 default y 78 ---help--- 79 Enables support for the on-chip EHCI controller on i.MX6 SoCs. 80 81config USB_EHCI_MX7 82 bool "Support for i.MX7 on-chip EHCI USB controller" 83 depends on ARCH_MX7 84 default y 85 ---help--- 86 Enables support for the on-chip EHCI controller on i.MX7 SoCs. 87 88if USB_EHCI_MX7 89 90config MXC_USB_OTG_HACTIVE 91 bool "USB Power pin high active" 92 ---help--- 93 Set the USB Power pin polarity to be high active (PWR_POL) 94 95endif 96 97config USB_EHCI_MSM 98 bool "Support for Qualcomm on-chip EHCI USB controller" 99 depends on DM_USB 100 select USB_ULPI_VIEWPORT 101 default n 102 ---help--- 103 Enables support for the on-chip EHCI controller on Qualcomm 104 Snapdragon SoCs. 105 This driver supports combination of Chipidea USB controller 106 and Synapsys USB PHY in host mode only. 107 108config USB_EHCI_ZYNQ 109 bool "Support for Xilinx Zynq on-chip EHCI USB controller" 110 depends on ARCH_ZYNQ 111 default y 112 ---help--- 113 Enable support for Zynq on-chip EHCI USB controller 114 115config USB_EHCI_GENERIC 116 bool "Support for generic EHCI USB controller" 117 depends on OF_CONTROL 118 depends on DM_USB 119 default n 120 ---help--- 121 Enables support for generic EHCI controller. 122 123endif # USB_EHCI_HCD 124 125config USB_OHCI_HCD 126 bool "OHCI HCD (USB 1.1) support" 127 ---help--- 128 The Open Host Controller Interface (OHCI) is a standard for accessing 129 USB 1.1 host controller hardware. It does more in hardware than Intel's 130 UHCI specification. If your USB host controller follows the OHCI spec, 131 say Y. On most non-x86 systems, and on x86 hardware that's not using a 132 USB controller from Intel or VIA, this is appropriate. If your host 133 controller doesn't use PCI, this is probably appropriate. For a PCI 134 based system where you're not sure, the "lspci -v" entry will list the 135 right "prog-if" for your USB controller(s): EHCI, OHCI, or UHCI. 136 137if USB_OHCI_HCD 138 139config USB_OHCI_GENERIC 140 bool "Support for generic OHCI USB controller" 141 depends on OF_CONTROL 142 depends on DM_USB 143 select USB_HOST 144 ---help--- 145 Enables support for generic OHCI controller. 146 147endif # USB_OHCI_HCD 148 149config USB_UHCI_HCD 150 bool "UHCI HCD (most Intel and VIA) support" 151 select USB_HOST 152 ---help--- 153 The Universal Host Controller Interface is a standard by Intel for 154 accessing the USB hardware in the PC (which is also called the USB 155 host controller). If your USB host controller conforms to this 156 standard, you may want to say Y, but see below. All recent boards 157 with Intel PCI chipsets (like intel 430TX, 440FX, 440LX, 440BX, 158 i810, i820) conform to this standard. Also all VIA PCI chipsets 159 (like VIA VP2, VP3, MVP3, Apollo Pro, Apollo Pro II or Apollo Pro 160 133) and LEON/GRLIB SoCs with the GRUSBHC controller. 161 If unsure, say Y. 162 163if USB_UHCI_HCD 164 165endif # USB_UHCI_HCD 166