1 /* 2 * Based on drivers/usb/gadget/omap1510_udc.c 3 * TI OMAP1510 USB bus interface driver 4 * 5 * (C) Copyright 2009 6 * Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com. 7 * 8 * SPDX-License-Identifier: GPL-2.0+ 9 */ 10 11 #include <common.h> 12 #include <asm/io.h> 13 14 #include <usbdevice.h> 15 #include "ep0.h" 16 #include <usb/designware_udc.h> 17 #include <usb/udc.h> 18 #include <asm/arch/hardware.h> 19 20 #define UDC_INIT_MDELAY 80 /* Device settle delay */ 21 22 /* Some kind of debugging output... */ 23 #ifndef DEBUG_DWUSBTTY 24 #define UDCDBG(str) 25 #define UDCDBGA(fmt, args...) 26 #else 27 #define UDCDBG(str) serial_printf(str "\n") 28 #define UDCDBGA(fmt, args...) serial_printf(fmt "\n", ##args) 29 #endif 30 31 static struct urb *ep0_urb; 32 static struct usb_device_instance *udc_device; 33 34 static struct plug_regs *const plug_regs_p = 35 (struct plug_regs * const)CONFIG_SYS_PLUG_BASE; 36 static struct udc_regs *const udc_regs_p = 37 (struct udc_regs * const)CONFIG_SYS_USBD_BASE; 38 static struct udc_endp_regs *const outep_regs_p = 39 &((struct udc_regs * const)CONFIG_SYS_USBD_BASE)->out_regs[0]; 40 static struct udc_endp_regs *const inep_regs_p = 41 &((struct udc_regs * const)CONFIG_SYS_USBD_BASE)->in_regs[0]; 42 43 /* 44 * udc_state_transition - Write the next packet to TxFIFO. 45 * @initial: Initial state. 46 * @final: Final state. 47 * 48 * Helper function to implement device state changes. The device states and 49 * the events that transition between them are: 50 * 51 * STATE_ATTACHED 52 * || /\ 53 * \/ || 54 * DEVICE_HUB_CONFIGURED DEVICE_HUB_RESET 55 * || /\ 56 * \/ || 57 * STATE_POWERED 58 * || /\ 59 * \/ || 60 * DEVICE_RESET DEVICE_POWER_INTERRUPTION 61 * || /\ 62 * \/ || 63 * STATE_DEFAULT 64 * || /\ 65 * \/ || 66 * DEVICE_ADDRESS_ASSIGNED DEVICE_RESET 67 * || /\ 68 * \/ || 69 * STATE_ADDRESSED 70 * || /\ 71 * \/ || 72 * DEVICE_CONFIGURED DEVICE_DE_CONFIGURED 73 * || /\ 74 * \/ || 75 * STATE_CONFIGURED 76 * 77 * udc_state_transition transitions up (in the direction from STATE_ATTACHED 78 * to STATE_CONFIGURED) from the specified initial state to the specified final 79 * state, passing through each intermediate state on the way. If the initial 80 * state is at or above (i.e. nearer to STATE_CONFIGURED) the final state, then 81 * no state transitions will take place. 82 * 83 * udc_state_transition also transitions down (in the direction from 84 * STATE_CONFIGURED to STATE_ATTACHED) from the specified initial state to the 85 * specified final state, passing through each intermediate state on the way. 86 * If the initial state is at or below (i.e. nearer to STATE_ATTACHED) the final 87 * state, then no state transitions will take place. 88 * 89 * This function must only be called with interrupts disabled. 90 */ 91 static void udc_state_transition(usb_device_state_t initial, 92 usb_device_state_t final) 93 { 94 if (initial < final) { 95 switch (initial) { 96 case STATE_ATTACHED: 97 usbd_device_event_irq(udc_device, 98 DEVICE_HUB_CONFIGURED, 0); 99 if (final == STATE_POWERED) 100 break; 101 case STATE_POWERED: 102 usbd_device_event_irq(udc_device, DEVICE_RESET, 0); 103 if (final == STATE_DEFAULT) 104 break; 105 case STATE_DEFAULT: 106 usbd_device_event_irq(udc_device, 107 DEVICE_ADDRESS_ASSIGNED, 0); 108 if (final == STATE_ADDRESSED) 109 break; 110 case STATE_ADDRESSED: 111 usbd_device_event_irq(udc_device, DEVICE_CONFIGURED, 0); 112 case STATE_CONFIGURED: 113 break; 114 default: 115 break; 116 } 117 } else if (initial > final) { 118 switch (initial) { 119 case STATE_CONFIGURED: 120 usbd_device_event_irq(udc_device, 121 DEVICE_DE_CONFIGURED, 0); 122 if (final == STATE_ADDRESSED) 123 break; 124 case STATE_ADDRESSED: 125 usbd_device_event_irq(udc_device, DEVICE_RESET, 0); 126 if (final == STATE_DEFAULT) 127 break; 128 case STATE_DEFAULT: 129 usbd_device_event_irq(udc_device, 130 DEVICE_POWER_INTERRUPTION, 0); 131 if (final == STATE_POWERED) 132 break; 133 case STATE_POWERED: 134 usbd_device_event_irq(udc_device, DEVICE_HUB_RESET, 0); 135 case STATE_ATTACHED: 136 break; 137 default: 138 break; 139 } 140 } 141 } 142 143 /* Stall endpoint */ 144 static void udc_stall_ep(u32 ep_num) 145 { 146 writel(readl(&inep_regs_p[ep_num].endp_cntl) | ENDP_CNTL_STALL, 147 &inep_regs_p[ep_num].endp_cntl); 148 149 writel(readl(&outep_regs_p[ep_num].endp_cntl) | ENDP_CNTL_STALL, 150 &outep_regs_p[ep_num].endp_cntl); 151 } 152 153 static void *get_fifo(int ep_num, int in) 154 { 155 u32 *fifo_ptr = (u32 *)CONFIG_SYS_FIFO_BASE; 156 157 switch (ep_num) { 158 case UDC_EP3: 159 fifo_ptr += readl(&inep_regs_p[1].endp_bsorfn); 160 /* break intentionally left out */ 161 162 case UDC_EP1: 163 fifo_ptr += readl(&inep_regs_p[0].endp_bsorfn); 164 /* break intentionally left out */ 165 166 case UDC_EP0: 167 default: 168 if (in) { 169 fifo_ptr += 170 readl(&outep_regs_p[2].endp_maxpacksize) >> 16; 171 /* break intentionally left out */ 172 } else { 173 break; 174 } 175 176 case UDC_EP2: 177 fifo_ptr += readl(&outep_regs_p[0].endp_maxpacksize) >> 16; 178 /* break intentionally left out */ 179 } 180 181 return (void *)fifo_ptr; 182 } 183 184 static int usbgetpckfromfifo(int epNum, u8 *bufp, u32 len) 185 { 186 u8 *fifo_ptr = (u8 *)get_fifo(epNum, 0); 187 u32 i, nw, nb; 188 u32 *wrdp; 189 u8 *bytp; 190 u32 tmp[128]; 191 192 if (readl(&udc_regs_p->dev_stat) & DEV_STAT_RXFIFO_EMPTY) 193 return -1; 194 195 nw = len / sizeof(u32); 196 nb = len % sizeof(u32); 197 198 /* use tmp buf if bufp is not word aligned */ 199 if ((int)bufp & 0x3) 200 wrdp = (u32 *)&tmp[0]; 201 else 202 wrdp = (u32 *)bufp; 203 204 for (i = 0; i < nw; i++) { 205 writel(readl(fifo_ptr), wrdp); 206 wrdp++; 207 } 208 209 bytp = (u8 *)wrdp; 210 for (i = 0; i < nb; i++) { 211 writeb(readb(fifo_ptr), bytp); 212 fifo_ptr++; 213 bytp++; 214 } 215 readl(&outep_regs_p[epNum].write_done); 216 217 /* copy back tmp buffer to bufp if bufp is not word aligned */ 218 if ((int)bufp & 0x3) 219 memcpy(bufp, tmp, len); 220 221 return 0; 222 } 223 224 static void usbputpcktofifo(int epNum, u8 *bufp, u32 len) 225 { 226 u32 i, nw, nb; 227 u32 *wrdp; 228 u8 *bytp; 229 u8 *fifo_ptr = get_fifo(epNum, 1); 230 231 nw = len / sizeof(int); 232 nb = len % sizeof(int); 233 wrdp = (u32 *)bufp; 234 for (i = 0; i < nw; i++) { 235 writel(*wrdp, fifo_ptr); 236 wrdp++; 237 } 238 239 bytp = (u8 *)wrdp; 240 for (i = 0; i < nb; i++) { 241 writeb(*bytp, fifo_ptr); 242 fifo_ptr++; 243 bytp++; 244 } 245 } 246 247 /* 248 * dw_write_noniso_tx_fifo - Write the next packet to TxFIFO. 249 * @endpoint: Endpoint pointer. 250 * 251 * If the endpoint has an active tx_urb, then the next packet of data from the 252 * URB is written to the tx FIFO. The total amount of data in the urb is given 253 * by urb->actual_length. The maximum amount of data that can be sent in any 254 * one packet is given by endpoint->tx_packetSize. The number of data bytes 255 * from this URB that have already been transmitted is given by endpoint->sent. 256 * endpoint->last is updated by this routine with the number of data bytes 257 * transmitted in this packet. 258 * 259 */ 260 static void dw_write_noniso_tx_fifo(struct usb_endpoint_instance 261 *endpoint) 262 { 263 struct urb *urb = endpoint->tx_urb; 264 int align; 265 266 if (urb) { 267 u32 last; 268 269 UDCDBGA("urb->buffer %p, buffer_length %d, actual_length %d", 270 urb->buffer, urb->buffer_length, urb->actual_length); 271 272 last = MIN(urb->actual_length - endpoint->sent, 273 endpoint->tx_packetSize); 274 275 if (last) { 276 u8 *cp = urb->buffer + endpoint->sent; 277 278 /* 279 * This ensures that USBD packet fifo is accessed 280 * - through word aligned pointer or 281 * - through non word aligned pointer but only 282 * with a max length to make the next packet 283 * word aligned 284 */ 285 286 align = ((ulong)cp % sizeof(int)); 287 if (align) 288 last = MIN(last, sizeof(int) - align); 289 290 UDCDBGA("endpoint->sent %d, tx_packetSize %d, last %d", 291 endpoint->sent, endpoint->tx_packetSize, last); 292 293 usbputpcktofifo(endpoint->endpoint_address & 294 USB_ENDPOINT_NUMBER_MASK, cp, last); 295 } 296 endpoint->last = last; 297 } 298 } 299 300 /* 301 * Handle SETUP USB interrupt. 302 * This function implements TRM Figure 14-14. 303 */ 304 static void dw_udc_setup(struct usb_endpoint_instance *endpoint) 305 { 306 u8 *datap = (u8 *)&ep0_urb->device_request; 307 int ep_addr = endpoint->endpoint_address; 308 309 UDCDBG("-> Entering device setup"); 310 usbgetpckfromfifo(ep_addr, datap, 8); 311 312 /* Try to process setup packet */ 313 if (ep0_recv_setup(ep0_urb)) { 314 /* Not a setup packet, stall next EP0 transaction */ 315 udc_stall_ep(0); 316 UDCDBG("can't parse setup packet, still waiting for setup"); 317 return; 318 } 319 320 /* Check direction */ 321 if ((ep0_urb->device_request.bmRequestType & USB_REQ_DIRECTION_MASK) 322 == USB_REQ_HOST2DEVICE) { 323 UDCDBG("control write on EP0"); 324 if (le16_to_cpu(ep0_urb->device_request.wLength)) { 325 /* Stall this request */ 326 UDCDBG("Stalling unsupported EP0 control write data " 327 "stage."); 328 udc_stall_ep(0); 329 } 330 } else { 331 332 UDCDBG("control read on EP0"); 333 /* 334 * The ep0_recv_setup function has already placed our response 335 * packet data in ep0_urb->buffer and the packet length in 336 * ep0_urb->actual_length. 337 */ 338 endpoint->tx_urb = ep0_urb; 339 endpoint->sent = 0; 340 /* 341 * Write packet data to the FIFO. dw_write_noniso_tx_fifo 342 * will update endpoint->last with the number of bytes written 343 * to the FIFO. 344 */ 345 dw_write_noniso_tx_fifo(endpoint); 346 347 writel(0x0, &inep_regs_p[ep_addr].write_done); 348 } 349 350 udc_unset_nak(endpoint->endpoint_address); 351 352 UDCDBG("<- Leaving device setup"); 353 } 354 355 /* 356 * Handle endpoint 0 RX interrupt 357 */ 358 static void dw_udc_ep0_rx(struct usb_endpoint_instance *endpoint) 359 { 360 u8 dummy[64]; 361 362 UDCDBG("RX on EP0"); 363 364 /* Check direction */ 365 if ((ep0_urb->device_request.bmRequestType 366 & USB_REQ_DIRECTION_MASK) == USB_REQ_HOST2DEVICE) { 367 /* 368 * This rx interrupt must be for a control write data 369 * stage packet. 370 * 371 * We don't support control write data stages. 372 * We should never end up here. 373 */ 374 375 UDCDBG("Stalling unexpected EP0 control write " 376 "data stage packet"); 377 udc_stall_ep(0); 378 } else { 379 /* 380 * This rx interrupt must be for a control read status 381 * stage packet. 382 */ 383 UDCDBG("ACK on EP0 control read status stage packet"); 384 u32 len = (readl(&outep_regs_p[0].endp_status) >> 11) & 0xfff; 385 usbgetpckfromfifo(0, dummy, len); 386 } 387 } 388 389 /* 390 * Handle endpoint 0 TX interrupt 391 */ 392 static void dw_udc_ep0_tx(struct usb_endpoint_instance *endpoint) 393 { 394 struct usb_device_request *request = &ep0_urb->device_request; 395 int ep_addr; 396 397 UDCDBG("TX on EP0"); 398 399 /* Check direction */ 400 if ((request->bmRequestType & USB_REQ_DIRECTION_MASK) == 401 USB_REQ_HOST2DEVICE) { 402 /* 403 * This tx interrupt must be for a control write status 404 * stage packet. 405 */ 406 UDCDBG("ACK on EP0 control write status stage packet"); 407 } else { 408 /* 409 * This tx interrupt must be for a control read data 410 * stage packet. 411 */ 412 int wLength = le16_to_cpu(request->wLength); 413 414 /* 415 * Update our count of bytes sent so far in this 416 * transfer. 417 */ 418 endpoint->sent += endpoint->last; 419 420 /* 421 * We are finished with this transfer if we have sent 422 * all of the bytes in our tx urb (urb->actual_length) 423 * unless we need a zero-length terminating packet. We 424 * need a zero-length terminating packet if we returned 425 * fewer bytes than were requested (wLength) by the host, 426 * and the number of bytes we returned is an exact 427 * multiple of the packet size endpoint->tx_packetSize. 428 */ 429 if ((endpoint->sent == ep0_urb->actual_length) && 430 ((ep0_urb->actual_length == wLength) || 431 (endpoint->last != endpoint->tx_packetSize))) { 432 /* Done with control read data stage. */ 433 UDCDBG("control read data stage complete"); 434 } else { 435 /* 436 * We still have another packet of data to send 437 * in this control read data stage or else we 438 * need a zero-length terminating packet. 439 */ 440 UDCDBG("ACK control read data stage packet"); 441 dw_write_noniso_tx_fifo(endpoint); 442 443 ep_addr = endpoint->endpoint_address; 444 writel(0x0, &inep_regs_p[ep_addr].write_done); 445 } 446 } 447 } 448 449 static struct usb_endpoint_instance *dw_find_ep(int ep) 450 { 451 int i; 452 453 for (i = 0; i < udc_device->bus->max_endpoints; i++) { 454 if ((udc_device->bus->endpoint_array[i].endpoint_address & 455 USB_ENDPOINT_NUMBER_MASK) == ep) 456 return &udc_device->bus->endpoint_array[i]; 457 } 458 return NULL; 459 } 460 461 /* 462 * Handle RX transaction on non-ISO endpoint. 463 * The ep argument is a physical endpoint number for a non-ISO IN endpoint 464 * in the range 1 to 15. 465 */ 466 static void dw_udc_epn_rx(int ep) 467 { 468 int nbytes = 0; 469 struct urb *urb; 470 struct usb_endpoint_instance *endpoint = dw_find_ep(ep); 471 472 if (endpoint) { 473 urb = endpoint->rcv_urb; 474 475 if (urb) { 476 u8 *cp = urb->buffer + urb->actual_length; 477 478 nbytes = (readl(&outep_regs_p[ep].endp_status) >> 11) & 479 0xfff; 480 usbgetpckfromfifo(ep, cp, nbytes); 481 usbd_rcv_complete(endpoint, nbytes, 0); 482 } 483 } 484 } 485 486 /* 487 * Handle TX transaction on non-ISO endpoint. 488 * The ep argument is a physical endpoint number for a non-ISO IN endpoint 489 * in the range 16 to 30. 490 */ 491 static void dw_udc_epn_tx(int ep) 492 { 493 struct usb_endpoint_instance *endpoint = dw_find_ep(ep); 494 495 if (!endpoint) 496 return; 497 498 /* 499 * We need to transmit a terminating zero-length packet now if 500 * we have sent all of the data in this URB and the transfer 501 * size was an exact multiple of the packet size. 502 */ 503 if (endpoint->tx_urb && 504 (endpoint->last == endpoint->tx_packetSize) && 505 (endpoint->tx_urb->actual_length - endpoint->sent - 506 endpoint->last == 0)) { 507 /* handle zero length packet here */ 508 writel(0x0, &inep_regs_p[ep].write_done); 509 510 } 511 512 if (endpoint->tx_urb && endpoint->tx_urb->actual_length) { 513 /* retire the data that was just sent */ 514 usbd_tx_complete(endpoint); 515 /* 516 * Check to see if we have more data ready to transmit 517 * now. 518 */ 519 if (endpoint->tx_urb && endpoint->tx_urb->actual_length) { 520 /* write data to FIFO */ 521 dw_write_noniso_tx_fifo(endpoint); 522 writel(0x0, &inep_regs_p[ep].write_done); 523 524 } else if (endpoint->tx_urb 525 && (endpoint->tx_urb->actual_length == 0)) { 526 /* udc_set_nak(ep); */ 527 } 528 } 529 } 530 531 /* 532 * Start of public functions. 533 */ 534 535 /* Called to start packet transmission. */ 536 int udc_endpoint_write(struct usb_endpoint_instance *endpoint) 537 { 538 udc_unset_nak(endpoint->endpoint_address & USB_ENDPOINT_NUMBER_MASK); 539 return 0; 540 } 541 542 /* Start to initialize h/w stuff */ 543 int udc_init(void) 544 { 545 int i; 546 u32 plug_st; 547 548 udc_device = NULL; 549 550 UDCDBG("starting"); 551 552 readl(&plug_regs_p->plug_pending); 553 554 for (i = 0; i < UDC_INIT_MDELAY; i++) 555 udelay(1000); 556 557 plug_st = readl(&plug_regs_p->plug_state); 558 writel(plug_st | PLUG_STATUS_EN, &plug_regs_p->plug_state); 559 560 writel(~0x0, &udc_regs_p->endp_int); 561 writel(~0x0, &udc_regs_p->dev_int_mask); 562 writel(~0x0, &udc_regs_p->endp_int_mask); 563 564 #ifndef CONFIG_USBD_HS 565 writel(DEV_CONF_FS_SPEED | DEV_CONF_REMWAKEUP | DEV_CONF_SELFPOW | 566 DEV_CONF_PHYINT_16, &udc_regs_p->dev_conf); 567 #else 568 writel(DEV_CONF_HS_SPEED | DEV_CONF_REMWAKEUP | DEV_CONF_SELFPOW | 569 DEV_CONF_PHYINT_16, &udc_regs_p->dev_conf); 570 #endif 571 572 writel(DEV_CNTL_SOFTDISCONNECT, &udc_regs_p->dev_cntl); 573 574 /* Clear all interrupts pending */ 575 writel(DEV_INT_MSK, &udc_regs_p->dev_int); 576 577 return 0; 578 } 579 580 int is_usbd_high_speed(void) 581 { 582 return (readl(&udc_regs_p->dev_stat) & DEV_STAT_ENUM) ? 0 : 1; 583 } 584 585 /* 586 * udc_setup_ep - setup endpoint 587 * Associate a physical endpoint with endpoint_instance 588 */ 589 void udc_setup_ep(struct usb_device_instance *device, 590 u32 ep, struct usb_endpoint_instance *endpoint) 591 { 592 UDCDBGA("setting up endpoint addr %x", endpoint->endpoint_address); 593 int ep_addr; 594 int ep_num, ep_type; 595 int packet_size; 596 int buffer_size; 597 int attributes; 598 char *tt; 599 u32 endp_intmask; 600 601 if ((ep != 0) && (udc_device->device_state < STATE_ADDRESSED)) 602 return; 603 604 tt = getenv("usbtty"); 605 if (!tt) 606 tt = "generic"; 607 608 ep_addr = endpoint->endpoint_address; 609 ep_num = ep_addr & USB_ENDPOINT_NUMBER_MASK; 610 611 if ((ep_addr & USB_ENDPOINT_DIR_MASK) == USB_DIR_IN) { 612 /* IN endpoint */ 613 packet_size = endpoint->tx_packetSize; 614 buffer_size = packet_size * 2; 615 attributes = endpoint->tx_attributes; 616 } else { 617 /* OUT endpoint */ 618 packet_size = endpoint->rcv_packetSize; 619 buffer_size = packet_size * 2; 620 attributes = endpoint->rcv_attributes; 621 } 622 623 switch (attributes & USB_ENDPOINT_XFERTYPE_MASK) { 624 case USB_ENDPOINT_XFER_CONTROL: 625 ep_type = ENDP_EPTYPE_CNTL; 626 break; 627 case USB_ENDPOINT_XFER_BULK: 628 default: 629 ep_type = ENDP_EPTYPE_BULK; 630 break; 631 case USB_ENDPOINT_XFER_INT: 632 ep_type = ENDP_EPTYPE_INT; 633 break; 634 case USB_ENDPOINT_XFER_ISOC: 635 ep_type = ENDP_EPTYPE_ISO; 636 break; 637 } 638 639 struct udc_endp_regs *out_p = &outep_regs_p[ep_num]; 640 struct udc_endp_regs *in_p = &inep_regs_p[ep_num]; 641 642 if (!ep_addr) { 643 /* Setup endpoint 0 */ 644 buffer_size = packet_size; 645 646 writel(readl(&in_p->endp_cntl) | ENDP_CNTL_CNAK, 647 &in_p->endp_cntl); 648 649 writel(readl(&out_p->endp_cntl) | ENDP_CNTL_CNAK, 650 &out_p->endp_cntl); 651 652 writel(ENDP_CNTL_CONTROL | ENDP_CNTL_FLUSH, &in_p->endp_cntl); 653 654 writel(buffer_size / sizeof(int), &in_p->endp_bsorfn); 655 656 writel(packet_size, &in_p->endp_maxpacksize); 657 658 writel(ENDP_CNTL_CONTROL | ENDP_CNTL_RRDY, &out_p->endp_cntl); 659 660 writel(packet_size | ((buffer_size / sizeof(int)) << 16), 661 &out_p->endp_maxpacksize); 662 663 } else if ((ep_addr & USB_ENDPOINT_DIR_MASK) == USB_DIR_IN) { 664 /* Setup the IN endpoint */ 665 writel(0x0, &in_p->endp_status); 666 writel((ep_type << 4) | ENDP_CNTL_RRDY, &in_p->endp_cntl); 667 writel(buffer_size / sizeof(int), &in_p->endp_bsorfn); 668 writel(packet_size, &in_p->endp_maxpacksize); 669 670 if (!strcmp(tt, "cdc_acm")) { 671 if (ep_type == ENDP_EPTYPE_INT) { 672 /* Conf no. 1 Interface no. 0 */ 673 writel((packet_size << 19) | 674 ENDP_EPDIR_IN | (1 << 7) | 675 (0 << 11) | (ep_type << 5) | ep_num, 676 &udc_regs_p->udc_endp_reg[ep_num]); 677 } else { 678 /* Conf no. 1 Interface no. 1 */ 679 writel((packet_size << 19) | 680 ENDP_EPDIR_IN | (1 << 7) | 681 (1 << 11) | (ep_type << 5) | ep_num, 682 &udc_regs_p->udc_endp_reg[ep_num]); 683 } 684 } else { 685 /* Conf no. 1 Interface no. 0 */ 686 writel((packet_size << 19) | 687 ENDP_EPDIR_IN | (1 << 7) | 688 (0 << 11) | (ep_type << 5) | ep_num, 689 &udc_regs_p->udc_endp_reg[ep_num]); 690 } 691 692 } else { 693 /* Setup the OUT endpoint */ 694 writel(0x0, &out_p->endp_status); 695 writel((ep_type << 4) | ENDP_CNTL_RRDY, &out_p->endp_cntl); 696 writel(packet_size | ((buffer_size / sizeof(int)) << 16), 697 &out_p->endp_maxpacksize); 698 699 if (!strcmp(tt, "cdc_acm")) { 700 writel((packet_size << 19) | 701 ENDP_EPDIR_OUT | (1 << 7) | 702 (1 << 11) | (ep_type << 5) | ep_num, 703 &udc_regs_p->udc_endp_reg[ep_num]); 704 } else { 705 writel((packet_size << 19) | 706 ENDP_EPDIR_OUT | (1 << 7) | 707 (0 << 11) | (ep_type << 5) | ep_num, 708 &udc_regs_p->udc_endp_reg[ep_num]); 709 } 710 711 } 712 713 endp_intmask = readl(&udc_regs_p->endp_int_mask); 714 endp_intmask &= ~((1 << ep_num) | 0x10000 << ep_num); 715 writel(endp_intmask, &udc_regs_p->endp_int_mask); 716 } 717 718 /* Turn on the USB connection by enabling the pullup resistor */ 719 void udc_connect(void) 720 { 721 u32 plug_st, dev_cntl; 722 723 dev_cntl = readl(&udc_regs_p->dev_cntl); 724 dev_cntl |= DEV_CNTL_SOFTDISCONNECT; 725 writel(dev_cntl, &udc_regs_p->dev_cntl); 726 727 udelay(1000); 728 729 dev_cntl = readl(&udc_regs_p->dev_cntl); 730 dev_cntl &= ~DEV_CNTL_SOFTDISCONNECT; 731 writel(dev_cntl, &udc_regs_p->dev_cntl); 732 733 plug_st = readl(&plug_regs_p->plug_state); 734 plug_st &= ~(PLUG_STATUS_PHY_RESET | PLUG_STATUS_PHY_MODE); 735 writel(plug_st, &plug_regs_p->plug_state); 736 } 737 738 /* Turn off the USB connection by disabling the pullup resistor */ 739 void udc_disconnect(void) 740 { 741 u32 plug_st; 742 743 writel(DEV_CNTL_SOFTDISCONNECT, &udc_regs_p->dev_cntl); 744 745 plug_st = readl(&plug_regs_p->plug_state); 746 plug_st |= (PLUG_STATUS_PHY_RESET | PLUG_STATUS_PHY_MODE); 747 writel(plug_st, &plug_regs_p->plug_state); 748 } 749 750 /* Switch on the UDC */ 751 void udc_enable(struct usb_device_instance *device) 752 { 753 UDCDBGA("enable device %p, status %d", device, device->status); 754 755 /* Save the device structure pointer */ 756 udc_device = device; 757 758 /* Setup ep0 urb */ 759 if (!ep0_urb) { 760 ep0_urb = 761 usbd_alloc_urb(udc_device, udc_device->bus->endpoint_array); 762 } else { 763 serial_printf("udc_enable: ep0_urb already allocated %p\n", 764 ep0_urb); 765 } 766 767 writel(DEV_INT_SOF, &udc_regs_p->dev_int_mask); 768 } 769 770 /** 771 * udc_startup - allow udc code to do any additional startup 772 */ 773 void udc_startup_events(struct usb_device_instance *device) 774 { 775 /* The DEVICE_INIT event puts the USB device in the state STATE_INIT. */ 776 usbd_device_event_irq(device, DEVICE_INIT, 0); 777 778 /* 779 * The DEVICE_CREATE event puts the USB device in the state 780 * STATE_ATTACHED. 781 */ 782 usbd_device_event_irq(device, DEVICE_CREATE, 0); 783 784 /* 785 * Some USB controller driver implementations signal 786 * DEVICE_HUB_CONFIGURED and DEVICE_RESET events here. 787 * DEVICE_HUB_CONFIGURED causes a transition to the state STATE_POWERED, 788 * and DEVICE_RESET causes a transition to the state STATE_DEFAULT. 789 * The DW USB client controller has the capability to detect when the 790 * USB cable is connected to a powered USB bus, so we will defer the 791 * DEVICE_HUB_CONFIGURED and DEVICE_RESET events until later. 792 */ 793 794 udc_enable(device); 795 } 796 797 /* 798 * Plug detection interrupt handling 799 */ 800 static void dw_udc_plug_irq(void) 801 { 802 if (readl(&plug_regs_p->plug_state) & PLUG_STATUS_ATTACHED) { 803 /* 804 * USB cable attached 805 * Turn off PHY reset bit (PLUG detect). 806 * Switch PHY opmode to normal operation (PLUG detect). 807 */ 808 udc_connect(); 809 writel(DEV_INT_SOF, &udc_regs_p->dev_int_mask); 810 811 UDCDBG("device attached and powered"); 812 udc_state_transition(udc_device->device_state, STATE_POWERED); 813 } else { 814 writel(~0x0, &udc_regs_p->dev_int_mask); 815 816 UDCDBG("device detached or unpowered"); 817 udc_state_transition(udc_device->device_state, STATE_ATTACHED); 818 } 819 } 820 821 /* 822 * Device interrupt handling 823 */ 824 static void dw_udc_dev_irq(void) 825 { 826 if (readl(&udc_regs_p->dev_int) & DEV_INT_USBRESET) { 827 writel(~0x0, &udc_regs_p->endp_int_mask); 828 829 writel(readl(&inep_regs_p[0].endp_cntl) | ENDP_CNTL_FLUSH, 830 &inep_regs_p[0].endp_cntl); 831 832 writel(DEV_INT_USBRESET, &udc_regs_p->dev_int); 833 834 /* 835 * This endpoint0 specific register can be programmed only 836 * after the phy clock is initialized 837 */ 838 writel((EP0_MAX_PACKET_SIZE << 19) | ENDP_EPTYPE_CNTL, 839 &udc_regs_p->udc_endp_reg[0]); 840 841 UDCDBG("device reset in progess"); 842 udc_state_transition(udc_device->device_state, STATE_DEFAULT); 843 } 844 845 /* Device Enumeration completed */ 846 if (readl(&udc_regs_p->dev_int) & DEV_INT_ENUM) { 847 writel(DEV_INT_ENUM, &udc_regs_p->dev_int); 848 849 /* Endpoint interrupt enabled for Ctrl IN & Ctrl OUT */ 850 writel(readl(&udc_regs_p->endp_int_mask) & ~0x10001, 851 &udc_regs_p->endp_int_mask); 852 853 UDCDBG("default -> addressed"); 854 udc_state_transition(udc_device->device_state, STATE_ADDRESSED); 855 } 856 857 /* The USB will be in SUSPEND in 3 ms */ 858 if (readl(&udc_regs_p->dev_int) & DEV_INT_INACTIVE) { 859 writel(DEV_INT_INACTIVE, &udc_regs_p->dev_int); 860 861 UDCDBG("entering inactive state"); 862 /* usbd_device_event_irq(udc_device, DEVICE_BUS_INACTIVE, 0); */ 863 } 864 865 /* SetConfiguration command received */ 866 if (readl(&udc_regs_p->dev_int) & DEV_INT_SETCFG) { 867 writel(DEV_INT_SETCFG, &udc_regs_p->dev_int); 868 869 UDCDBG("entering configured state"); 870 udc_state_transition(udc_device->device_state, 871 STATE_CONFIGURED); 872 } 873 874 /* SetInterface command received */ 875 if (readl(&udc_regs_p->dev_int) & DEV_INT_SETINTF) 876 writel(DEV_INT_SETINTF, &udc_regs_p->dev_int); 877 878 /* USB Suspend detected on cable */ 879 if (readl(&udc_regs_p->dev_int) & DEV_INT_SUSPUSB) { 880 writel(DEV_INT_SUSPUSB, &udc_regs_p->dev_int); 881 882 UDCDBG("entering suspended state"); 883 usbd_device_event_irq(udc_device, DEVICE_BUS_INACTIVE, 0); 884 } 885 886 /* USB Start-Of-Frame detected on cable */ 887 if (readl(&udc_regs_p->dev_int) & DEV_INT_SOF) 888 writel(DEV_INT_SOF, &udc_regs_p->dev_int); 889 } 890 891 /* 892 * Endpoint interrupt handling 893 */ 894 static void dw_udc_endpoint_irq(void) 895 { 896 while (readl(&udc_regs_p->endp_int) & ENDP0_INT_CTRLOUT) { 897 898 writel(ENDP0_INT_CTRLOUT, &udc_regs_p->endp_int); 899 900 if ((readl(&outep_regs_p[0].endp_status) & ENDP_STATUS_OUTMSK) 901 == ENDP_STATUS_OUT_SETUP) { 902 dw_udc_setup(udc_device->bus->endpoint_array + 0); 903 writel(ENDP_STATUS_OUT_SETUP, 904 &outep_regs_p[0].endp_status); 905 906 } else if ((readl(&outep_regs_p[0].endp_status) & 907 ENDP_STATUS_OUTMSK) == ENDP_STATUS_OUT_DATA) { 908 dw_udc_ep0_rx(udc_device->bus->endpoint_array + 0); 909 writel(ENDP_STATUS_OUT_DATA, 910 &outep_regs_p[0].endp_status); 911 912 } else if ((readl(&outep_regs_p[0].endp_status) & 913 ENDP_STATUS_OUTMSK) == ENDP_STATUS_OUT_NONE) { 914 /* NONE received */ 915 } 916 917 writel(0x0, &outep_regs_p[0].endp_status); 918 } 919 920 if (readl(&udc_regs_p->endp_int) & ENDP0_INT_CTRLIN) { 921 dw_udc_ep0_tx(udc_device->bus->endpoint_array + 0); 922 923 writel(ENDP_STATUS_IN, &inep_regs_p[0].endp_status); 924 writel(ENDP0_INT_CTRLIN, &udc_regs_p->endp_int); 925 } 926 927 if (readl(&udc_regs_p->endp_int) & ENDP_INT_NONISOOUT_MSK) { 928 u32 epnum = 0; 929 u32 ep_int = readl(&udc_regs_p->endp_int) & 930 ENDP_INT_NONISOOUT_MSK; 931 932 ep_int >>= 16; 933 while (0x0 == (ep_int & 0x1)) { 934 ep_int >>= 1; 935 epnum++; 936 } 937 938 writel((1 << 16) << epnum, &udc_regs_p->endp_int); 939 940 if ((readl(&outep_regs_p[epnum].endp_status) & 941 ENDP_STATUS_OUTMSK) == ENDP_STATUS_OUT_DATA) { 942 943 dw_udc_epn_rx(epnum); 944 writel(ENDP_STATUS_OUT_DATA, 945 &outep_regs_p[epnum].endp_status); 946 } else if ((readl(&outep_regs_p[epnum].endp_status) & 947 ENDP_STATUS_OUTMSK) == ENDP_STATUS_OUT_NONE) { 948 writel(0x0, &outep_regs_p[epnum].endp_status); 949 } 950 } 951 952 if (readl(&udc_regs_p->endp_int) & ENDP_INT_NONISOIN_MSK) { 953 u32 epnum = 0; 954 u32 ep_int = readl(&udc_regs_p->endp_int) & 955 ENDP_INT_NONISOIN_MSK; 956 957 while (0x0 == (ep_int & 0x1)) { 958 ep_int >>= 1; 959 epnum++; 960 } 961 962 if (readl(&inep_regs_p[epnum].endp_status) & ENDP_STATUS_IN) { 963 writel(ENDP_STATUS_IN, 964 &outep_regs_p[epnum].endp_status); 965 dw_udc_epn_tx(epnum); 966 967 writel(ENDP_STATUS_IN, 968 &outep_regs_p[epnum].endp_status); 969 } 970 971 writel((1 << epnum), &udc_regs_p->endp_int); 972 } 973 } 974 975 /* 976 * UDC interrupts 977 */ 978 void udc_irq(void) 979 { 980 /* 981 * Loop while we have interrupts. 982 * If we don't do this, the input chain 983 * polling delay is likely to miss 984 * host requests. 985 */ 986 while (readl(&plug_regs_p->plug_pending)) 987 dw_udc_plug_irq(); 988 989 while (readl(&udc_regs_p->dev_int)) 990 dw_udc_dev_irq(); 991 992 if (readl(&udc_regs_p->endp_int)) 993 dw_udc_endpoint_irq(); 994 } 995 996 /* Flow control */ 997 void udc_set_nak(int epid) 998 { 999 writel(readl(&inep_regs_p[epid].endp_cntl) | ENDP_CNTL_SNAK, 1000 &inep_regs_p[epid].endp_cntl); 1001 1002 writel(readl(&outep_regs_p[epid].endp_cntl) | ENDP_CNTL_SNAK, 1003 &outep_regs_p[epid].endp_cntl); 1004 } 1005 1006 void udc_unset_nak(int epid) 1007 { 1008 u32 val; 1009 1010 val = readl(&inep_regs_p[epid].endp_cntl); 1011 val &= ~ENDP_CNTL_SNAK; 1012 val |= ENDP_CNTL_CNAK; 1013 writel(val, &inep_regs_p[epid].endp_cntl); 1014 1015 val = readl(&outep_regs_p[epid].endp_cntl); 1016 val &= ~ENDP_CNTL_SNAK; 1017 val |= ENDP_CNTL_CNAK; 1018 writel(val, &outep_regs_p[epid].endp_cntl); 1019 } 1020