1# 2# USB Gadget support on a system involves 3# (a) a peripheral controller, and 4# (b) the gadget driver using it. 5# 6# NOTE: Gadget support ** DOES NOT ** depend on host-side CONFIG_USB !! 7# 8# - Host systems (like PCs) need CONFIG_USB (with "A" jacks). 9# - Peripherals (like PDAs) need CONFIG_USB_GADGET (with "B" jacks). 10# - Some systems have both kinds of controllers. 11# 12# With help from a special transceiver and a "Mini-AB" jack, systems with 13# both kinds of controller can also support "USB On-the-Go" (CONFIG_USB_OTG). 14# 15 16menuconfig USB_GADGET 17 bool "USB Gadget Support" 18 help 19 USB is a master/slave protocol, organized with one master 20 host (such as a PC) controlling up to 127 peripheral devices. 21 The USB hardware is asymmetric, which makes it easier to set up: 22 you can't connect a "to-the-host" connector to a peripheral. 23 24 U-Boot can run in the host, or in the peripheral. In both cases 25 you need a low level bus controller driver, and some software 26 talking to it. Peripheral controllers are often discrete silicon, 27 or are integrated with the CPU in a microcontroller. The more 28 familiar host side controllers have names like "EHCI", "OHCI", 29 or "UHCI", and are usually integrated into southbridges on PC 30 motherboards. 31 32 Enable this configuration option if you want to run U-Boot inside 33 a USB peripheral device. Configure one hardware driver for your 34 peripheral/device side bus controller, and a "gadget driver" for 35 your peripheral protocol. 36 37if USB_GADGET 38 39config USB_GADGET_ATMEL_USBA 40 bool "Atmel USBA" 41 select USB_GADGET_DUALSPEED 42 help 43 USBA is the integrated high-speed USB Device controller on 44 the AT32AP700x, some AT91SAM9 and AT91CAP9 processors from Atmel. 45 46config USB_GADGET_BCM_UDC_OTG_PHY 47 bool "Broadcom UDC OTG PHY" 48 help 49 Enable the Broadcom UDC OTG physical device interface. 50 51config USB_GADGET_DWC2_OTG 52 bool "DesignWare USB2.0 HS OTG controller (gadget mode)" 53 select USB_GADGET_DUALSPEED 54 help 55 The Designware USB2.0 high-speed gadget controller 56 integrated into many SoCs. Select this option if you want the 57 driver to operate in Peripheral mode. This option requires 58 USB_GADGET to be enabled. 59 60if USB_GADGET_DWC2_OTG 61 62config USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8 63 bool "DesignWare USB2.0 HS OTG controller 8-bit PHY bus width" 64 help 65 Set the Designware USB2.0 high-speed OTG controller 66 PHY interface width to 8 bits, rather than the default (16 bits). 67 68endif # USB_GADGET_DWC2_OTG 69 70config CI_UDC 71 bool "ChipIdea device controller" 72 select USB_GADGET_DUALSPEED 73 help 74 Say Y here to enable device controller functionality of the 75 ChipIdea driver. 76 77config USB_GADGET_VBUS_DRAW 78 int "Maximum VBUS Power usage (2-500 mA)" 79 range 2 500 80 default 2 81 help 82 Some devices need to draw power from USB when they are 83 configured, perhaps to operate circuitry or to recharge 84 batteries. This is in addition to any local power supply, 85 such as an AC adapter or batteries. 86 87 Enter the maximum power your device draws through USB, in 88 milliAmperes. The permitted range of values is 2 - 500 mA; 89 0 mA would be legal, but can make some hosts misbehave. 90 91 This value will be used except for system-specific gadget 92 drivers that have more specific information. 93 94# Selected by UDC drivers that support high-speed operation. 95config USB_GADGET_DUALSPEED 96 bool 97 98config USB_GADGET_DOWNLOAD 99 bool "Enable USB download gadget" 100 help 101 Composite USB download gadget support (g_dnl) for download functions. 102 This code works on top of composite gadget. 103 104if USB_GADGET_DOWNLOAD 105 106config G_DNL_MANUFACTURER 107 string "Vendor name of USB device" 108 109config G_DNL_VENDOR_NUM 110 hex "Vendor ID of USB device" 111 112config G_DNL_PRODUCT_NUM 113 hex "Product ID of USB device" 114 115config USBNET_DEVADDR 116 string "USB Gadget Ethernet device mac address" 117 default "de:ad:be:ef:00:01" 118 119endif # USB_GADGET_DOWNLOAD 120 121endif # USB_GADGET 122