1# 2# USB Gadget support on a system involves 3# (a) a peripheral controller, and 4# (b) the gadget driver using it. 5# 6# NOTE: Gadget support ** DOES NOT ** depend on host-side CONFIG_USB !! 7# 8# - Host systems (like PCs) need CONFIG_USB (with "A" jacks). 9# - Peripherals (like PDAs) need CONFIG_USB_GADGET (with "B" jacks). 10# - Some systems have both kinds of controllers. 11# 12# With help from a special transceiver and a "Mini-AB" jack, systems with 13# both kinds of controller can also support "USB On-the-Go" (CONFIG_USB_OTG). 14# 15 16menuconfig USB_GADGET 17 bool "USB Gadget Support" 18 help 19 USB is a master/slave protocol, organized with one master 20 host (such as a PC) controlling up to 127 peripheral devices. 21 The USB hardware is asymmetric, which makes it easier to set up: 22 you can't connect a "to-the-host" connector to a peripheral. 23 24 U-Boot can run in the host, or in the peripheral. In both cases 25 you need a low level bus controller driver, and some software 26 talking to it. Peripheral controllers are often discrete silicon, 27 or are integrated with the CPU in a microcontroller. The more 28 familiar host side controllers have names like "EHCI", "OHCI", 29 or "UHCI", and are usually integrated into southbridges on PC 30 motherboards. 31 32 Enable this configuration option if you want to run U-Boot inside 33 a USB peripheral device. Configure one hardware driver for your 34 peripheral/device side bus controller, and a "gadget driver" for 35 your peripheral protocol. 36 37if USB_GADGET 38 39config USB_GADGET_MANUFACTURER 40 string "Vendor name of the USB device" 41 default "Allwinner Technology" if ARCH_SUNXI 42 default "U-Boot" 43 help 44 Vendor name of the USB device emulated, reported to the host device. 45 This is usually either the manufacturer of the device or the SoC. 46 47config USB_GADGET_VENDOR_NUM 48 hex "Vendor ID of the USB device" 49 default 0x1f3a if ARCH_SUNXI 50 default 0x0 51 help 52 Vendor ID of the USB device emulated, reported to the host device. 53 This is usually the board or SoC vendor's, unless you've registered 54 for one. 55 56config USB_GADGET_PRODUCT_NUM 57 hex "Product ID of the USB device" 58 default 0x1010 if ARCH_SUNXI 59 default 0x0 60 help 61 Product ID of the USB device emulated, reported to the host device. 62 63config USB_GADGET_ATMEL_USBA 64 bool "Atmel USBA" 65 select USB_GADGET_DUALSPEED 66 help 67 USBA is the integrated high-speed USB Device controller on 68 the AT32AP700x, some AT91SAM9 and AT91CAP9 processors from Atmel. 69 70config USB_GADGET_BCM_UDC_OTG_PHY 71 bool "Broadcom UDC OTG PHY" 72 help 73 Enable the Broadcom UDC OTG physical device interface. 74 75config USB_GADGET_DWC2_OTG 76 bool "DesignWare USB2.0 HS OTG controller (gadget mode)" 77 select USB_GADGET_DUALSPEED 78 help 79 The Designware USB2.0 high-speed gadget controller 80 integrated into many SoCs. Select this option if you want the 81 driver to operate in Peripheral mode. This option requires 82 USB_GADGET to be enabled. 83 84if USB_GADGET_DWC2_OTG 85 86config USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8 87 bool "DesignWare USB2.0 HS OTG controller 8-bit PHY bus width" 88 help 89 Set the Designware USB2.0 high-speed OTG controller 90 PHY interface width to 8 bits, rather than the default (16 bits). 91 92endif # USB_GADGET_DWC2_OTG 93 94config CI_UDC 95 bool "ChipIdea device controller" 96 select USB_GADGET_DUALSPEED 97 help 98 Say Y here to enable device controller functionality of the 99 ChipIdea driver. 100 101config USB_GADGET_VBUS_DRAW 102 int "Maximum VBUS Power usage (2-500 mA)" 103 range 2 500 104 default 2 105 help 106 Some devices need to draw power from USB when they are 107 configured, perhaps to operate circuitry or to recharge 108 batteries. This is in addition to any local power supply, 109 such as an AC adapter or batteries. 110 111 Enter the maximum power your device draws through USB, in 112 milliAmperes. The permitted range of values is 2 - 500 mA; 113 0 mA would be legal, but can make some hosts misbehave. 114 115 This value will be used except for system-specific gadget 116 drivers that have more specific information. 117 118# Selected by UDC drivers that support high-speed operation. 119config USB_GADGET_DUALSPEED 120 bool 121 122config USB_GADGET_DOWNLOAD 123 bool "Enable USB download gadget" 124 help 125 Composite USB download gadget support (g_dnl) for download functions. 126 This code works on top of composite gadget. 127 128if USB_GADGET_DOWNLOAD 129 130config USB_FUNCTION_MASS_STORAGE 131 bool "Enable USB mass storage gadget" 132 help 133 Enable mass storage protocol support in U-Boot. It allows exporting 134 the eMMC/SD card content to HOST PC so it can be mounted. 135 136config USB_FUNCTION_ROCKUSB 137 bool "Enable USB rockusb gadget" 138 help 139 Rockusb protocol is widely used by Rockchip SoC based devices. It can 140 read/write info, image to/from devices. This enables the USB part of 141 the rockusb gadget.for more detail about Rockusb protocol, please see 142 doc/README.rockusb 143 144config USB_FUNCTION_SDP 145 bool "Enable USB SDP (Serial Download Protocol)" 146 help 147 Enable Serial Download Protocol (SDP) device support in U-Boot. This 148 allows to download images into memory and execute (jump to) them 149 using the same protocol as implemented by the i.MX family's boot ROM. 150 151config USB_FUNCTION_THOR 152 bool "Enable USB THOR gadget" 153 help 154 Enable Tizen's THOR download protocol support in U-Boot. It 155 allows downloading images into memory and flash them to target device. 156 157endif # USB_GADGET_DOWNLOAD 158 159config USB_ETHER 160 bool "USB Ethernet Gadget" 161 default y if ARCH_SUNXI && USB_MUSB_GADGET 162 help 163 Creates an Ethernet network device through a USB peripheral 164 controller. This will create a network interface on both the device 165 (U-Boot) and the host (remote device) that can be used just like any 166 other nework interface. 167 It will bind on the peripheral USB controller, ignoring the USB hosts 168 controllers in the system. 169 170if USB_ETHER 171 172choice 173 prompt "USB Ethernet Gadget Model" 174 default USB_ETH_RNDIS 175 help 176 There is several models (protocols) to implement Ethernet over USB 177 devices. The main ones are Microsoft's RNDIS and USB's CDC-Ethernet 178 (also called CDC-ECM). RNDIS is obviously compatible with Windows, 179 while CDC-ECM is not. Most other operating systems support both, so 180 if inter-operability is a concern, RNDIS is to be preferred. 181 182config USB_ETH_CDC 183 bool "CDC-ECM Protocol" 184 help 185 CDC (Communications Device Class) is the standard for Ethernet over 186 USB devices. While there's several alternatives, the most widely used 187 protocol is ECM (Ethernet Control Model). However, compatibility with 188 Windows is not that great. 189 190config USB_ETH_RNDIS 191 bool "RNDIS Protocol" 192 help 193 The RNDIS (Remote Network Driver Interface Specification) is a 194 Microsoft proprietary protocol to create an Ethernet device over USB. 195 Windows obviously supports it, as well as all the major operating 196 systems, so it's the best option for compatibility. 197 198endchoice 199 200config USBNET_DEVADDR 201 string "USB Gadget Ethernet device mac address" 202 default "de:ad:be:ef:00:01" 203 help 204 Ethernet MAC address of the device-side (ie. local board's) MAC 205 address of the usb_ether interface 206 207config USBNET_HOST_ADDR 208 string "USB Gadget Ethernet host mac address" 209 default "de:ad:be:ef:00:00" 210 help 211 Ethernet MAC address of the host-side (ie. remote device's) MAC 212 address of the usb_ether interface 213 214endif # USB_ETHER 215 216endif # USB_GADGET 217