xref: /openbmc/u-boot/drivers/usb/gadget/Kconfig (revision 4e97e257)
1#
2# USB Gadget support on a system involves
3#    (a) a peripheral controller, and
4#    (b) the gadget driver using it.
5#
6# NOTE:  Gadget support ** DOES NOT ** depend on host-side CONFIG_USB !!
7#
8#  - Host systems (like PCs) need CONFIG_USB (with "A" jacks).
9#  - Peripherals (like PDAs) need CONFIG_USB_GADGET (with "B" jacks).
10#  - Some systems have both kinds of controllers.
11#
12# With help from a special transceiver and a "Mini-AB" jack, systems with
13# both kinds of controller can also support "USB On-the-Go" (CONFIG_USB_OTG).
14#
15
16menuconfig USB_GADGET
17	bool "USB Gadget Support"
18	help
19	   USB is a master/slave protocol, organized with one master
20	   host (such as a PC) controlling up to 127 peripheral devices.
21	   The USB hardware is asymmetric, which makes it easier to set up:
22	   you can't connect a "to-the-host" connector to a peripheral.
23
24	   U-Boot can run in the host, or in the peripheral.  In both cases
25	   you need a low level bus controller driver, and some software
26	   talking to it.  Peripheral controllers are often discrete silicon,
27	   or are integrated with the CPU in a microcontroller.  The more
28	   familiar host side controllers have names like "EHCI", "OHCI",
29	   or "UHCI", and are usually integrated into southbridges on PC
30	   motherboards.
31
32	   Enable this configuration option if you want to run U-Boot inside
33	   a USB peripheral device.  Configure one hardware driver for your
34	   peripheral/device side bus controller, and a "gadget driver" for
35	   your peripheral protocol.
36
37if USB_GADGET
38
39config USB_GADGET_MANUFACTURER
40	string "Vendor name of the USB device"
41	default "Allwinner Technology" if ARCH_SUNXI
42	default "U-Boot"
43	help
44	  Vendor name of the USB device emulated, reported to the host device.
45	  This is usually either the manufacturer of the device or the SoC.
46
47config USB_GADGET_VENDOR_NUM
48	hex "Vendor ID of the USB device"
49	default 0x1f3a if ARCH_SUNXI
50	default 0x0
51	help
52	  Vendor ID of the USB device emulated, reported to the host device.
53	  This is usually the board or SoC vendor's, unless you've registered
54	  for one.
55
56config USB_GADGET_PRODUCT_NUM
57	hex "Product ID of the USB device"
58	default 0x1010 if ARCH_SUNXI
59	default 0x0
60	help
61	  Product ID of the USB device emulated, reported to the host device.
62
63config USB_GADGET_ATMEL_USBA
64	bool "Atmel USBA"
65	select USB_GADGET_DUALSPEED
66	help
67	  USBA is the integrated high-speed USB Device controller on
68	  the AT32AP700x, some AT91SAM9 and AT91CAP9 processors from Atmel.
69
70config USB_GADGET_BCM_UDC_OTG_PHY
71	bool "Broadcom UDC OTG PHY"
72	help
73	  Enable the Broadcom UDC OTG physical device interface.
74
75config USB_GADGET_DWC2_OTG
76	bool "DesignWare USB2.0 HS OTG controller (gadget mode)"
77	select USB_GADGET_DUALSPEED
78	help
79	  The Designware USB2.0 high-speed gadget controller
80	  integrated into many SoCs. Select this option if you want the
81	  driver to operate in Peripheral mode. This option requires
82	  USB_GADGET to be enabled.
83
84if USB_GADGET_DWC2_OTG
85
86config USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8
87	bool "DesignWare USB2.0 HS OTG controller 8-bit PHY bus width"
88	help
89	  Set the Designware USB2.0 high-speed OTG controller
90	  PHY interface width to 8 bits, rather than the default (16 bits).
91
92endif # USB_GADGET_DWC2_OTG
93
94config CI_UDC
95	bool "ChipIdea device controller"
96	select USB_GADGET_DUALSPEED
97	help
98	  Say Y here to enable device controller functionality of the
99	  ChipIdea driver.
100
101config USB_GADGET_VBUS_DRAW
102	int "Maximum VBUS Power usage (2-500 mA)"
103	range 2 500
104	default 2
105	help
106	   Some devices need to draw power from USB when they are
107	   configured, perhaps to operate circuitry or to recharge
108	   batteries.  This is in addition to any local power supply,
109	   such as an AC adapter or batteries.
110
111	   Enter the maximum power your device draws through USB, in
112	   milliAmperes.  The permitted range of values is 2 - 500 mA;
113	   0 mA would be legal, but can make some hosts misbehave.
114
115	   This value will be used except for system-specific gadget
116	   drivers that have more specific information.
117
118# Selected by UDC drivers that support high-speed operation.
119config USB_GADGET_DUALSPEED
120	bool
121
122config USB_GADGET_DOWNLOAD
123	bool "Enable USB download gadget"
124	help
125	  Composite USB download gadget support (g_dnl) for download functions.
126	  This code works on top of composite gadget.
127
128if USB_GADGET_DOWNLOAD
129
130config USB_FUNCTION_SDP
131	bool "Enable USB SDP (Serial Download Protocol)"
132	help
133	  Enable Serial Download Protocol (SDP) device support in U-Boot. This
134	  allows to download images into memory and execute (jump to) them
135	  using the same protocol as implemented by the i.MX family's boot ROM.
136
137endif # USB_GADGET_DOWNLOAD
138
139config USB_ETHER
140	bool "USB Ethernet Gadget"
141	default y if ARCH_SUNXI && USB_MUSB_GADGET
142	help
143	  Creates an Ethernet network device through a USB peripheral
144	  controller. This will create a network interface on both the device
145	  (U-Boot) and the host (remote device) that can be used just like any
146	  other nework interface.
147	  It will bind on the peripheral USB controller, ignoring the USB hosts
148	  controllers in the system.
149
150if USB_ETHER
151
152choice
153	prompt "USB Ethernet Gadget Model"
154	default USB_ETH_RNDIS
155	help
156	  There is several models (protocols) to implement Ethernet over USB
157	  devices. The main ones are Microsoft's RNDIS and USB's CDC-Ethernet
158	  (also called CDC-ECM). RNDIS is obviously compatible with Windows,
159	  while CDC-ECM is not. Most other operating systems support both, so
160	  if inter-operability is a concern, RNDIS is to be preferred.
161
162config USB_ETH_CDC
163	bool "CDC-ECM Protocol"
164	help
165	  CDC (Communications Device Class) is the standard for Ethernet over
166	  USB devices. While there's several alternatives, the most widely used
167	  protocol is ECM (Ethernet Control Model). However, compatibility with
168	  Windows is not that great.
169
170config USB_ETH_RNDIS
171	bool "RNDIS Protocol"
172	help
173	  The RNDIS (Remote Network Driver Interface Specification) is a
174	  Microsoft proprietary protocol to create an Ethernet device over USB.
175	  Windows obviously supports it, as well as all the major operating
176	  systems, so it's the best option for compatibility.
177
178endchoice
179
180config USBNET_DEVADDR
181	string "USB Gadget Ethernet device mac address"
182	default "de:ad:be:ef:00:01"
183	help
184	  Ethernet MAC address of the device-side (ie. local board's) MAC
185	  address of the usb_ether interface
186
187config USBNET_HOST_ADDR
188	string "USB Gadget Ethernet host mac address"
189	default "de:ad:be:ef:00:00"
190	help
191	  Ethernet MAC address of the host-side (ie. remote device's) MAC
192	  address of the usb_ether interface
193
194endif # USB_ETHER
195
196endif # USB_GADGET
197