xref: /openbmc/u-boot/drivers/usb/Kconfig (revision e11ef3d2)
1menuconfig USB
2	bool "USB support"
3	---help---
4	  Universal Serial Bus (USB) is a specification for a serial bus
5	  subsystem which offers higher speeds and more features than the
6	  traditional PC serial port.  The bus supplies power to peripherals
7	  and allows for hot swapping.  Up to 127 USB peripherals can be
8	  connected to a single USB host in a tree structure.
9
10	  The USB host is the root of the tree, the peripherals are the
11	  leaves and the inner nodes are special USB devices called hubs.
12	  Most PCs now have USB host ports, used to connect peripherals
13	  such as scanners, keyboards, mice, modems, cameras, disks,
14	  flash memory, network links, and printers to the PC.
15
16	  Say Y here if your device has an USB port, either host, peripheral or
17	  dual-role.
18
19	  For an USB host port, you then need to say Y to at least one of the
20	  Host Controller Driver (HCD) options below.  Choose a USB 1.1
21	  controller, such as "UHCI HCD support" or "OHCI HCD support",
22	  and "EHCI HCD (USB 2.0) support" except for older systems that
23	  do not have USB 2.0 support.  It doesn't normally hurt to select
24	  them all if you are not certain.
25
26	  If your system has a device-side USB port, used in the peripheral
27	  side of the USB protocol, see the "USB Gadget" framework instead.
28
29	  After choosing your HCD, then select drivers for the USB peripherals
30	  you'll be using.  You may want to check out the information provided
31	  in <file:Documentation/usb/> and especially the links given in
32	  <file:Documentation/usb/usb-help.txt>.
33
34if USB
35
36config DM_USB
37	bool "Enable driver model for USB"
38	depends on USB && DM
39	help
40	  Enable driver model for USB. The USB interface is then implemented
41	  by the USB uclass. Multiple USB controllers of different types
42	  (XHCI, EHCI) can be attached and used. The 'usb' command works as
43	  normal. OCHI is not supported at present.
44
45	  Much of the code is shared but with this option enabled the USB
46	  uclass takes care of device enumeration. USB devices can be
47	  declared with the U_BOOT_USB_DEVICE() macro and will be
48	  automatically probed when found on the bus.
49
50config SPL_DM_USB
51	bool "Enable driver model for USB in SPL"
52	depends on DM_USB
53	default y
54
55config DM_USB_GADGET
56	bool "Enable driver model for USB Gadget"
57	depends on DM_USB
58	help
59	  Enable driver model for USB Gadget (Peripheral
60	  mode)
61
62config SPL_DM_USB_GADGET
63	bool "Enable driver model for USB Gadget in sPL"
64	depends on SPL_DM_USB
65	help
66	  Enable driver model for USB Gadget in SPL
67	  (Peripheral mode)
68
69source "drivers/usb/host/Kconfig"
70
71source "drivers/usb/dwc3/Kconfig"
72
73source "drivers/usb/musb/Kconfig"
74
75source "drivers/usb/musb-new/Kconfig"
76
77source "drivers/usb/emul/Kconfig"
78
79source "drivers/usb/phy/Kconfig"
80
81source "drivers/usb/ulpi/Kconfig"
82
83comment "USB peripherals"
84
85config USB_STORAGE
86	bool "USB Mass Storage support"
87	depends on !(BLK && !DM_USB)
88	---help---
89	  Say Y here if you want to connect USB mass storage devices to your
90	  board's USB port.
91
92config USB_KEYBOARD
93	bool "USB Keyboard support"
94	select SYS_STDIO_DEREGISTER
95	---help---
96	  Say Y here if you want to use a USB keyboard for U-Boot command line
97	  input.
98
99if USB_KEYBOARD
100
101choice
102	prompt "USB keyboard polling"
103	default SYS_USB_EVENT_POLL
104	---help---
105	  Enable a polling mechanism for USB keyboard.
106
107	config SYS_USB_EVENT_POLL
108		bool "Interrupt polling"
109
110	config SYS_USB_EVENT_POLL_VIA_INT_QUEUE
111		bool "Poll via interrupt queue"
112
113	config SYS_USB_EVENT_POLL_VIA_CONTROL_EP
114		bool "Poll via control EP"
115
116endchoice
117
118endif
119
120source "drivers/usb/gadget/Kconfig"
121
122source "drivers/usb/eth/Kconfig"
123
124endif
125