1 /* 2 * (C) Copyright 2013 Xilinx, Inc. 3 * (C) Copyright 2015 Jagan Teki <jteki@openedev.com> 4 * 5 * Xilinx Zynq PS SPI controller driver (master mode only) 6 * 7 * SPDX-License-Identifier: GPL-2.0+ 8 */ 9 10 #include <common.h> 11 #include <dm.h> 12 #include <malloc.h> 13 #include <spi.h> 14 #include <asm/io.h> 15 16 DECLARE_GLOBAL_DATA_PTR; 17 18 /* zynq spi register bit masks ZYNQ_SPI_<REG>_<BIT>_MASK */ 19 #define ZYNQ_SPI_CR_MSA_MASK BIT(15) /* Manual start enb */ 20 #define ZYNQ_SPI_CR_MCS_MASK BIT(14) /* Manual chip select */ 21 #define ZYNQ_SPI_CR_CS_MASK GENMASK(13, 10) /* Chip select */ 22 #define ZYNQ_SPI_CR_BAUD_MASK GENMASK(5, 3) /* Baud rate div */ 23 #define ZYNQ_SPI_CR_CPHA_MASK BIT(2) /* Clock phase */ 24 #define ZYNQ_SPI_CR_CPOL_MASK BIT(1) /* Clock polarity */ 25 #define ZYNQ_SPI_CR_MSTREN_MASK BIT(0) /* Mode select */ 26 #define ZYNQ_SPI_IXR_RXNEMPTY_MASK BIT(4) /* RX_FIFO_not_empty */ 27 #define ZYNQ_SPI_IXR_TXOW_MASK BIT(2) /* TX_FIFO_not_full */ 28 #define ZYNQ_SPI_IXR_ALL_MASK GENMASK(6, 0) /* All IXR bits */ 29 #define ZYNQ_SPI_ENR_SPI_EN_MASK BIT(0) /* SPI Enable */ 30 31 #define ZYNQ_SPI_CR_BAUD_MAX 8 /* Baud rate divisor max val */ 32 #define ZYNQ_SPI_CR_BAUD_SHIFT 3 /* Baud rate divisor shift */ 33 #define ZYNQ_SPI_CR_SS_SHIFT 10 /* Slave select shift */ 34 35 #define ZYNQ_SPI_FIFO_DEPTH 128 36 #ifndef CONFIG_SYS_ZYNQ_SPI_WAIT 37 #define CONFIG_SYS_ZYNQ_SPI_WAIT (CONFIG_SYS_HZ/100) /* 10 ms */ 38 #endif 39 40 /* zynq spi register set */ 41 struct zynq_spi_regs { 42 u32 cr; /* 0x00 */ 43 u32 isr; /* 0x04 */ 44 u32 ier; /* 0x08 */ 45 u32 idr; /* 0x0C */ 46 u32 imr; /* 0x10 */ 47 u32 enr; /* 0x14 */ 48 u32 dr; /* 0x18 */ 49 u32 txdr; /* 0x1C */ 50 u32 rxdr; /* 0x20 */ 51 }; 52 53 54 /* zynq spi platform data */ 55 struct zynq_spi_platdata { 56 struct zynq_spi_regs *regs; 57 u32 frequency; /* input frequency */ 58 u32 speed_hz; 59 }; 60 61 /* zynq spi priv */ 62 struct zynq_spi_priv { 63 struct zynq_spi_regs *regs; 64 u8 cs; 65 u8 mode; 66 u8 fifo_depth; 67 u32 freq; /* required frequency */ 68 }; 69 70 static int zynq_spi_ofdata_to_platdata(struct udevice *bus) 71 { 72 struct zynq_spi_platdata *plat = bus->platdata; 73 const void *blob = gd->fdt_blob; 74 int node = bus->of_offset; 75 76 plat->regs = (struct zynq_spi_regs *)dev_get_addr(bus); 77 78 /* FIXME: Use 250MHz as a suitable default */ 79 plat->frequency = fdtdec_get_int(blob, node, "spi-max-frequency", 80 250000000); 81 plat->speed_hz = plat->frequency / 2; 82 83 debug("%s: regs=%p max-frequency=%d\n", __func__, 84 plat->regs, plat->frequency); 85 86 return 0; 87 } 88 89 static void zynq_spi_init_hw(struct zynq_spi_priv *priv) 90 { 91 struct zynq_spi_regs *regs = priv->regs; 92 u32 confr; 93 94 /* Disable SPI */ 95 writel(~ZYNQ_SPI_ENR_SPI_EN_MASK, ®s->enr); 96 97 /* Disable Interrupts */ 98 writel(ZYNQ_SPI_IXR_ALL_MASK, ®s->idr); 99 100 /* Clear RX FIFO */ 101 while (readl(®s->isr) & 102 ZYNQ_SPI_IXR_RXNEMPTY_MASK) 103 readl(®s->rxdr); 104 105 /* Clear Interrupts */ 106 writel(ZYNQ_SPI_IXR_ALL_MASK, ®s->isr); 107 108 /* Manual slave select and Auto start */ 109 confr = ZYNQ_SPI_CR_MCS_MASK | ZYNQ_SPI_CR_CS_MASK | 110 ZYNQ_SPI_CR_MSTREN_MASK; 111 confr &= ~ZYNQ_SPI_CR_MSA_MASK; 112 writel(confr, ®s->cr); 113 114 /* Enable SPI */ 115 writel(ZYNQ_SPI_ENR_SPI_EN_MASK, ®s->enr); 116 } 117 118 static int zynq_spi_probe(struct udevice *bus) 119 { 120 struct zynq_spi_platdata *plat = dev_get_platdata(bus); 121 struct zynq_spi_priv *priv = dev_get_priv(bus); 122 123 priv->regs = plat->regs; 124 priv->fifo_depth = ZYNQ_SPI_FIFO_DEPTH; 125 126 /* init the zynq spi hw */ 127 zynq_spi_init_hw(priv); 128 129 return 0; 130 } 131 132 static void spi_cs_activate(struct udevice *dev) 133 { 134 struct udevice *bus = dev->parent; 135 struct zynq_spi_priv *priv = dev_get_priv(bus); 136 struct zynq_spi_regs *regs = priv->regs; 137 u32 cr; 138 139 clrbits_le32(®s->cr, ZYNQ_SPI_CR_CS_MASK); 140 cr = readl(®s->cr); 141 /* 142 * CS cal logic: CS[13:10] 143 * xxx0 - cs0 144 * xx01 - cs1 145 * x011 - cs2 146 */ 147 cr |= (~(1 << priv->cs) << ZYNQ_SPI_CR_SS_SHIFT) & ZYNQ_SPI_CR_CS_MASK; 148 writel(cr, ®s->cr); 149 } 150 151 static void spi_cs_deactivate(struct udevice *dev) 152 { 153 struct udevice *bus = dev->parent; 154 struct zynq_spi_priv *priv = dev_get_priv(bus); 155 struct zynq_spi_regs *regs = priv->regs; 156 157 setbits_le32(®s->cr, ZYNQ_SPI_CR_CS_MASK); 158 } 159 160 static int zynq_spi_claim_bus(struct udevice *dev) 161 { 162 struct udevice *bus = dev->parent; 163 struct zynq_spi_priv *priv = dev_get_priv(bus); 164 struct zynq_spi_regs *regs = priv->regs; 165 166 writel(ZYNQ_SPI_ENR_SPI_EN_MASK, ®s->enr); 167 168 return 0; 169 } 170 171 static int zynq_spi_release_bus(struct udevice *dev) 172 { 173 struct udevice *bus = dev->parent; 174 struct zynq_spi_priv *priv = dev_get_priv(bus); 175 struct zynq_spi_regs *regs = priv->regs; 176 177 writel(~ZYNQ_SPI_ENR_SPI_EN_MASK, ®s->enr); 178 179 return 0; 180 } 181 182 static int zynq_spi_xfer(struct udevice *dev, unsigned int bitlen, 183 const void *dout, void *din, unsigned long flags) 184 { 185 struct udevice *bus = dev->parent; 186 struct zynq_spi_priv *priv = dev_get_priv(bus); 187 struct zynq_spi_regs *regs = priv->regs; 188 struct dm_spi_slave_platdata *slave_plat = dev_get_parent_platdata(dev); 189 u32 len = bitlen / 8; 190 u32 tx_len = len, rx_len = len, tx_tvl; 191 const u8 *tx_buf = dout; 192 u8 *rx_buf = din, buf; 193 u32 ts, status; 194 195 debug("spi_xfer: bus:%i cs:%i bitlen:%i len:%i flags:%lx\n", 196 bus->seq, slave_plat->cs, bitlen, len, flags); 197 198 if (bitlen % 8) { 199 debug("spi_xfer: Non byte aligned SPI transfer\n"); 200 return -1; 201 } 202 203 priv->cs = slave_plat->cs; 204 if (flags & SPI_XFER_BEGIN) 205 spi_cs_activate(dev); 206 207 while (rx_len > 0) { 208 /* Write the data into TX FIFO - tx threshold is fifo_depth */ 209 tx_tvl = 0; 210 while ((tx_tvl < priv->fifo_depth) && tx_len) { 211 if (tx_buf) 212 buf = *tx_buf++; 213 else 214 buf = 0; 215 writel(buf, ®s->txdr); 216 tx_len--; 217 tx_tvl++; 218 } 219 220 /* Check TX FIFO completion */ 221 ts = get_timer(0); 222 status = readl(®s->isr); 223 while (!(status & ZYNQ_SPI_IXR_TXOW_MASK)) { 224 if (get_timer(ts) > CONFIG_SYS_ZYNQ_SPI_WAIT) { 225 printf("spi_xfer: Timeout! TX FIFO not full\n"); 226 return -1; 227 } 228 status = readl(®s->isr); 229 } 230 231 /* Read the data from RX FIFO */ 232 status = readl(®s->isr); 233 while (status & ZYNQ_SPI_IXR_RXNEMPTY_MASK) { 234 buf = readl(®s->rxdr); 235 if (rx_buf) 236 *rx_buf++ = buf; 237 status = readl(®s->isr); 238 rx_len--; 239 } 240 } 241 242 if (flags & SPI_XFER_END) 243 spi_cs_deactivate(dev); 244 245 return 0; 246 } 247 248 static int zynq_spi_set_speed(struct udevice *bus, uint speed) 249 { 250 struct zynq_spi_platdata *plat = bus->platdata; 251 struct zynq_spi_priv *priv = dev_get_priv(bus); 252 struct zynq_spi_regs *regs = priv->regs; 253 uint32_t confr; 254 u8 baud_rate_val = 0; 255 256 if (speed > plat->frequency) 257 speed = plat->frequency; 258 259 /* Set the clock frequency */ 260 confr = readl(®s->cr); 261 if (speed == 0) { 262 /* Set baudrate x8, if the freq is 0 */ 263 baud_rate_val = 0x2; 264 } else if (plat->speed_hz != speed) { 265 while ((baud_rate_val < ZYNQ_SPI_CR_BAUD_MAX) && 266 ((plat->frequency / 267 (2 << baud_rate_val)) > speed)) 268 baud_rate_val++; 269 plat->speed_hz = speed / (2 << baud_rate_val); 270 } 271 confr &= ~ZYNQ_SPI_CR_BAUD_MASK; 272 confr |= (baud_rate_val << ZYNQ_SPI_CR_BAUD_SHIFT); 273 274 writel(confr, ®s->cr); 275 priv->freq = speed; 276 277 debug("zynq_spi_set_speed: regs=%p, speed=%d\n", 278 priv->regs, priv->freq); 279 280 return 0; 281 } 282 283 static int zynq_spi_set_mode(struct udevice *bus, uint mode) 284 { 285 struct zynq_spi_priv *priv = dev_get_priv(bus); 286 struct zynq_spi_regs *regs = priv->regs; 287 uint32_t confr; 288 289 /* Set the SPI Clock phase and polarities */ 290 confr = readl(®s->cr); 291 confr &= ~(ZYNQ_SPI_CR_CPHA_MASK | ZYNQ_SPI_CR_CPOL_MASK); 292 293 if (mode & SPI_CPHA) 294 confr |= ZYNQ_SPI_CR_CPHA_MASK; 295 if (mode & SPI_CPOL) 296 confr |= ZYNQ_SPI_CR_CPOL_MASK; 297 298 writel(confr, ®s->cr); 299 priv->mode = mode; 300 301 debug("zynq_spi_set_mode: regs=%p, mode=%d\n", priv->regs, priv->mode); 302 303 return 0; 304 } 305 306 static const struct dm_spi_ops zynq_spi_ops = { 307 .claim_bus = zynq_spi_claim_bus, 308 .release_bus = zynq_spi_release_bus, 309 .xfer = zynq_spi_xfer, 310 .set_speed = zynq_spi_set_speed, 311 .set_mode = zynq_spi_set_mode, 312 }; 313 314 static const struct udevice_id zynq_spi_ids[] = { 315 { .compatible = "xlnx,zynq-spi-r1p6" }, 316 { .compatible = "cdns,spi-r1p6" }, 317 { } 318 }; 319 320 U_BOOT_DRIVER(zynq_spi) = { 321 .name = "zynq_spi", 322 .id = UCLASS_SPI, 323 .of_match = zynq_spi_ids, 324 .ops = &zynq_spi_ops, 325 .ofdata_to_platdata = zynq_spi_ofdata_to_platdata, 326 .platdata_auto_alloc_size = sizeof(struct zynq_spi_platdata), 327 .priv_auto_alloc_size = sizeof(struct zynq_spi_priv), 328 .probe = zynq_spi_probe, 329 }; 330