1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * (C) Copyright 2013 Xilinx, Inc. 4 * (C) Copyright 2015 Jagan Teki <jteki@openedev.com> 5 * 6 * Xilinx Zynq Quad-SPI(QSPI) controller driver (master mode only) 7 */ 8 9 #include <common.h> 10 #include <dm.h> 11 #include <malloc.h> 12 #include <spi.h> 13 #include <asm/io.h> 14 15 DECLARE_GLOBAL_DATA_PTR; 16 17 /* zynq qspi register bit masks ZYNQ_QSPI_<REG>_<BIT>_MASK */ 18 #define ZYNQ_QSPI_CR_IFMODE_MASK BIT(31) /* Flash intrface mode*/ 19 #define ZYNQ_QSPI_CR_MSA_MASK BIT(15) /* Manual start enb */ 20 #define ZYNQ_QSPI_CR_MCS_MASK BIT(14) /* Manual chip select */ 21 #define ZYNQ_QSPI_CR_PCS_MASK BIT(10) /* Peri chip select */ 22 #define ZYNQ_QSPI_CR_FW_MASK GENMASK(7, 6) /* FIFO width */ 23 #define ZYNQ_QSPI_CR_SS_MASK GENMASK(13, 10) /* Slave Select */ 24 #define ZYNQ_QSPI_CR_BAUD_MASK GENMASK(5, 3) /* Baud rate div */ 25 #define ZYNQ_QSPI_CR_CPHA_MASK BIT(2) /* Clock phase */ 26 #define ZYNQ_QSPI_CR_CPOL_MASK BIT(1) /* Clock polarity */ 27 #define ZYNQ_QSPI_CR_MSTREN_MASK BIT(0) /* Mode select */ 28 #define ZYNQ_QSPI_IXR_RXNEMPTY_MASK BIT(4) /* RX_FIFO_not_empty */ 29 #define ZYNQ_QSPI_IXR_TXOW_MASK BIT(2) /* TX_FIFO_not_full */ 30 #define ZYNQ_QSPI_IXR_ALL_MASK GENMASK(6, 0) /* All IXR bits */ 31 #define ZYNQ_QSPI_ENR_SPI_EN_MASK BIT(0) /* SPI Enable */ 32 #define ZYNQ_QSPI_LQSPICFG_LQMODE_MASK BIT(31) /* Linear QSPI Mode */ 33 34 /* zynq qspi Transmit Data Register */ 35 #define ZYNQ_QSPI_TXD_00_00_OFFSET 0x1C /* Transmit 4-byte inst */ 36 #define ZYNQ_QSPI_TXD_00_01_OFFSET 0x80 /* Transmit 1-byte inst */ 37 #define ZYNQ_QSPI_TXD_00_10_OFFSET 0x84 /* Transmit 2-byte inst */ 38 #define ZYNQ_QSPI_TXD_00_11_OFFSET 0x88 /* Transmit 3-byte inst */ 39 40 #define ZYNQ_QSPI_TXFIFO_THRESHOLD 1 /* Tx FIFO threshold level*/ 41 #define ZYNQ_QSPI_RXFIFO_THRESHOLD 32 /* Rx FIFO threshold level */ 42 43 #define ZYNQ_QSPI_CR_BAUD_MAX 8 /* Baud rate divisor max val */ 44 #define ZYNQ_QSPI_CR_BAUD_SHIFT 3 /* Baud rate divisor shift */ 45 #define ZYNQ_QSPI_CR_SS_SHIFT 10 /* Slave select shift */ 46 47 #define ZYNQ_QSPI_FIFO_DEPTH 63 48 #ifndef CONFIG_SYS_ZYNQ_QSPI_WAIT 49 #define CONFIG_SYS_ZYNQ_QSPI_WAIT CONFIG_SYS_HZ/100 /* 10 ms */ 50 #endif 51 52 /* zynq qspi register set */ 53 struct zynq_qspi_regs { 54 u32 cr; /* 0x00 */ 55 u32 isr; /* 0x04 */ 56 u32 ier; /* 0x08 */ 57 u32 idr; /* 0x0C */ 58 u32 imr; /* 0x10 */ 59 u32 enr; /* 0x14 */ 60 u32 dr; /* 0x18 */ 61 u32 txd0r; /* 0x1C */ 62 u32 drxr; /* 0x20 */ 63 u32 sicr; /* 0x24 */ 64 u32 txftr; /* 0x28 */ 65 u32 rxftr; /* 0x2C */ 66 u32 gpior; /* 0x30 */ 67 u32 reserved0[19]; 68 u32 txd1r; /* 0x80 */ 69 u32 txd2r; /* 0x84 */ 70 u32 txd3r; /* 0x88 */ 71 u32 reserved1[5]; 72 u32 lqspicfg; /* 0xA0 */ 73 u32 lqspists; /* 0xA4 */ 74 }; 75 76 /* zynq qspi platform data */ 77 struct zynq_qspi_platdata { 78 struct zynq_qspi_regs *regs; 79 u32 frequency; /* input frequency */ 80 u32 speed_hz; 81 }; 82 83 /* zynq qspi priv */ 84 struct zynq_qspi_priv { 85 struct zynq_qspi_regs *regs; 86 u8 cs; 87 u8 mode; 88 u8 fifo_depth; 89 u32 freq; /* required frequency */ 90 const void *tx_buf; 91 void *rx_buf; 92 unsigned len; 93 int bytes_to_transfer; 94 int bytes_to_receive; 95 unsigned int is_inst; 96 unsigned cs_change:1; 97 }; 98 99 static int zynq_qspi_ofdata_to_platdata(struct udevice *bus) 100 { 101 struct zynq_qspi_platdata *plat = bus->platdata; 102 const void *blob = gd->fdt_blob; 103 int node = dev_of_offset(bus); 104 105 plat->regs = (struct zynq_qspi_regs *)fdtdec_get_addr(blob, 106 node, "reg"); 107 108 /* FIXME: Use 166MHz as a suitable default */ 109 plat->frequency = fdtdec_get_int(blob, node, "spi-max-frequency", 110 166666666); 111 plat->speed_hz = plat->frequency / 2; 112 113 debug("%s: regs=%p max-frequency=%d\n", __func__, 114 plat->regs, plat->frequency); 115 116 return 0; 117 } 118 119 static void zynq_qspi_init_hw(struct zynq_qspi_priv *priv) 120 { 121 struct zynq_qspi_regs *regs = priv->regs; 122 u32 confr; 123 124 /* Disable QSPI */ 125 writel(~ZYNQ_QSPI_ENR_SPI_EN_MASK, ®s->enr); 126 127 /* Disable Interrupts */ 128 writel(ZYNQ_QSPI_IXR_ALL_MASK, ®s->idr); 129 130 /* Clear the TX and RX threshold reg */ 131 writel(ZYNQ_QSPI_TXFIFO_THRESHOLD, ®s->txftr); 132 writel(ZYNQ_QSPI_RXFIFO_THRESHOLD, ®s->rxftr); 133 134 /* Clear the RX FIFO */ 135 while (readl(®s->isr) & ZYNQ_QSPI_IXR_RXNEMPTY_MASK) 136 readl(®s->drxr); 137 138 /* Clear Interrupts */ 139 writel(ZYNQ_QSPI_IXR_ALL_MASK, ®s->isr); 140 141 /* Manual slave select and Auto start */ 142 confr = readl(®s->cr); 143 confr &= ~ZYNQ_QSPI_CR_MSA_MASK; 144 confr |= ZYNQ_QSPI_CR_IFMODE_MASK | ZYNQ_QSPI_CR_MCS_MASK | 145 ZYNQ_QSPI_CR_PCS_MASK | ZYNQ_QSPI_CR_FW_MASK | 146 ZYNQ_QSPI_CR_MSTREN_MASK; 147 writel(confr, ®s->cr); 148 149 /* Disable the LQSPI feature */ 150 confr = readl(®s->lqspicfg); 151 confr &= ~ZYNQ_QSPI_LQSPICFG_LQMODE_MASK; 152 writel(confr, ®s->lqspicfg); 153 154 /* Enable SPI */ 155 writel(ZYNQ_QSPI_ENR_SPI_EN_MASK, ®s->enr); 156 } 157 158 static int zynq_qspi_probe(struct udevice *bus) 159 { 160 struct zynq_qspi_platdata *plat = dev_get_platdata(bus); 161 struct zynq_qspi_priv *priv = dev_get_priv(bus); 162 163 priv->regs = plat->regs; 164 priv->fifo_depth = ZYNQ_QSPI_FIFO_DEPTH; 165 166 /* init the zynq spi hw */ 167 zynq_qspi_init_hw(priv); 168 169 return 0; 170 } 171 172 /* 173 * zynq_qspi_read_data - Copy data to RX buffer 174 * @zqspi: Pointer to the zynq_qspi structure 175 * @data: The 32 bit variable where data is stored 176 * @size: Number of bytes to be copied from data to RX buffer 177 */ 178 static void zynq_qspi_read_data(struct zynq_qspi_priv *priv, u32 data, u8 size) 179 { 180 u8 byte3; 181 182 debug("%s: data 0x%04x rx_buf addr: 0x%08x size %d\n", __func__ , 183 data, (unsigned)(priv->rx_buf), size); 184 185 if (priv->rx_buf) { 186 switch (size) { 187 case 1: 188 *((u8 *)priv->rx_buf) = data; 189 priv->rx_buf += 1; 190 break; 191 case 2: 192 *((u16 *)priv->rx_buf) = data; 193 priv->rx_buf += 2; 194 break; 195 case 3: 196 *((u16 *)priv->rx_buf) = data; 197 priv->rx_buf += 2; 198 byte3 = (u8)(data >> 16); 199 *((u8 *)priv->rx_buf) = byte3; 200 priv->rx_buf += 1; 201 break; 202 case 4: 203 /* Can not assume word aligned buffer */ 204 memcpy(priv->rx_buf, &data, size); 205 priv->rx_buf += 4; 206 break; 207 default: 208 /* This will never execute */ 209 break; 210 } 211 } 212 priv->bytes_to_receive -= size; 213 if (priv->bytes_to_receive < 0) 214 priv->bytes_to_receive = 0; 215 } 216 217 /* 218 * zynq_qspi_write_data - Copy data from TX buffer 219 * @zqspi: Pointer to the zynq_qspi structure 220 * @data: Pointer to the 32 bit variable where data is to be copied 221 * @size: Number of bytes to be copied from TX buffer to data 222 */ 223 static void zynq_qspi_write_data(struct zynq_qspi_priv *priv, 224 u32 *data, u8 size) 225 { 226 if (priv->tx_buf) { 227 switch (size) { 228 case 1: 229 *data = *((u8 *)priv->tx_buf); 230 priv->tx_buf += 1; 231 *data |= 0xFFFFFF00; 232 break; 233 case 2: 234 *data = *((u16 *)priv->tx_buf); 235 priv->tx_buf += 2; 236 *data |= 0xFFFF0000; 237 break; 238 case 3: 239 *data = *((u16 *)priv->tx_buf); 240 priv->tx_buf += 2; 241 *data |= (*((u8 *)priv->tx_buf) << 16); 242 priv->tx_buf += 1; 243 *data |= 0xFF000000; 244 break; 245 case 4: 246 /* Can not assume word aligned buffer */ 247 memcpy(data, priv->tx_buf, size); 248 priv->tx_buf += 4; 249 break; 250 default: 251 /* This will never execute */ 252 break; 253 } 254 } else { 255 *data = 0; 256 } 257 258 debug("%s: data 0x%08x tx_buf addr: 0x%08x size %d\n", __func__, 259 *data, (u32)priv->tx_buf, size); 260 261 priv->bytes_to_transfer -= size; 262 if (priv->bytes_to_transfer < 0) 263 priv->bytes_to_transfer = 0; 264 } 265 266 static void zynq_qspi_chipselect(struct zynq_qspi_priv *priv, int is_on) 267 { 268 u32 confr; 269 struct zynq_qspi_regs *regs = priv->regs; 270 271 confr = readl(®s->cr); 272 273 if (is_on) { 274 /* Select the slave */ 275 confr &= ~ZYNQ_QSPI_CR_SS_MASK; 276 confr |= (~(1 << priv->cs) << ZYNQ_QSPI_CR_SS_SHIFT) & 277 ZYNQ_QSPI_CR_SS_MASK; 278 } else 279 /* Deselect the slave */ 280 confr |= ZYNQ_QSPI_CR_SS_MASK; 281 282 writel(confr, ®s->cr); 283 } 284 285 /* 286 * zynq_qspi_fill_tx_fifo - Fills the TX FIFO with as many bytes as possible 287 * @zqspi: Pointer to the zynq_qspi structure 288 */ 289 static void zynq_qspi_fill_tx_fifo(struct zynq_qspi_priv *priv, u32 size) 290 { 291 u32 data = 0; 292 u32 fifocount = 0; 293 unsigned len, offset; 294 struct zynq_qspi_regs *regs = priv->regs; 295 static const unsigned offsets[4] = { 296 ZYNQ_QSPI_TXD_00_00_OFFSET, ZYNQ_QSPI_TXD_00_01_OFFSET, 297 ZYNQ_QSPI_TXD_00_10_OFFSET, ZYNQ_QSPI_TXD_00_11_OFFSET }; 298 299 while ((fifocount < size) && 300 (priv->bytes_to_transfer > 0)) { 301 if (priv->bytes_to_transfer >= 4) { 302 if (priv->tx_buf) { 303 memcpy(&data, priv->tx_buf, 4); 304 priv->tx_buf += 4; 305 } else { 306 data = 0; 307 } 308 writel(data, ®s->txd0r); 309 priv->bytes_to_transfer -= 4; 310 fifocount++; 311 } else { 312 /* Write TXD1, TXD2, TXD3 only if TxFIFO is empty. */ 313 if (!(readl(®s->isr) 314 & ZYNQ_QSPI_IXR_TXOW_MASK) && 315 !priv->rx_buf) 316 return; 317 len = priv->bytes_to_transfer; 318 zynq_qspi_write_data(priv, &data, len); 319 offset = (priv->rx_buf) ? offsets[0] : offsets[len]; 320 writel(data, ®s->cr + (offset / 4)); 321 } 322 } 323 } 324 325 /* 326 * zynq_qspi_irq_poll - Interrupt service routine of the QSPI controller 327 * @zqspi: Pointer to the zynq_qspi structure 328 * 329 * This function handles TX empty and Mode Fault interrupts only. 330 * On TX empty interrupt this function reads the received data from RX FIFO and 331 * fills the TX FIFO if there is any data remaining to be transferred. 332 * On Mode Fault interrupt this function indicates that transfer is completed, 333 * the SPI subsystem will identify the error as the remaining bytes to be 334 * transferred is non-zero. 335 * 336 * returns: 0 for poll timeout 337 * 1 transfer operation complete 338 */ 339 static int zynq_qspi_irq_poll(struct zynq_qspi_priv *priv) 340 { 341 struct zynq_qspi_regs *regs = priv->regs; 342 u32 rxindex = 0; 343 u32 rxcount; 344 u32 status, timeout; 345 346 /* Poll until any of the interrupt status bits are set */ 347 timeout = get_timer(0); 348 do { 349 status = readl(®s->isr); 350 } while ((status == 0) && 351 (get_timer(timeout) < CONFIG_SYS_ZYNQ_QSPI_WAIT)); 352 353 if (status == 0) { 354 printf("zynq_qspi_irq_poll: Timeout!\n"); 355 return -ETIMEDOUT; 356 } 357 358 writel(status, ®s->isr); 359 360 /* Disable all interrupts */ 361 writel(ZYNQ_QSPI_IXR_ALL_MASK, ®s->idr); 362 if ((status & ZYNQ_QSPI_IXR_TXOW_MASK) || 363 (status & ZYNQ_QSPI_IXR_RXNEMPTY_MASK)) { 364 /* 365 * This bit is set when Tx FIFO has < THRESHOLD entries. We have 366 * the THRESHOLD value set to 1, so this bit indicates Tx FIFO 367 * is empty 368 */ 369 rxcount = priv->bytes_to_receive - priv->bytes_to_transfer; 370 rxcount = (rxcount % 4) ? ((rxcount/4)+1) : (rxcount/4); 371 while ((rxindex < rxcount) && 372 (rxindex < ZYNQ_QSPI_RXFIFO_THRESHOLD)) { 373 /* Read out the data from the RX FIFO */ 374 u32 data; 375 data = readl(®s->drxr); 376 377 if (priv->bytes_to_receive >= 4) { 378 if (priv->rx_buf) { 379 memcpy(priv->rx_buf, &data, 4); 380 priv->rx_buf += 4; 381 } 382 priv->bytes_to_receive -= 4; 383 } else { 384 zynq_qspi_read_data(priv, data, 385 priv->bytes_to_receive); 386 } 387 rxindex++; 388 } 389 390 if (priv->bytes_to_transfer) { 391 /* There is more data to send */ 392 zynq_qspi_fill_tx_fifo(priv, 393 ZYNQ_QSPI_RXFIFO_THRESHOLD); 394 395 writel(ZYNQ_QSPI_IXR_ALL_MASK, ®s->ier); 396 } else { 397 /* 398 * If transfer and receive is completed then only send 399 * complete signal 400 */ 401 if (!priv->bytes_to_receive) { 402 /* return operation complete */ 403 writel(ZYNQ_QSPI_IXR_ALL_MASK, 404 ®s->idr); 405 return 1; 406 } 407 } 408 } 409 410 return 0; 411 } 412 413 /* 414 * zynq_qspi_start_transfer - Initiates the QSPI transfer 415 * @qspi: Pointer to the spi_device structure 416 * @transfer: Pointer to the spi_transfer structure which provide information 417 * about next transfer parameters 418 * 419 * This function fills the TX FIFO, starts the QSPI transfer, and waits for the 420 * transfer to be completed. 421 * 422 * returns: Number of bytes transferred in the last transfer 423 */ 424 static int zynq_qspi_start_transfer(struct zynq_qspi_priv *priv) 425 { 426 u32 data = 0; 427 struct zynq_qspi_regs *regs = priv->regs; 428 429 debug("%s: qspi: 0x%08x transfer: 0x%08x len: %d\n", __func__, 430 (u32)priv, (u32)priv, priv->len); 431 432 priv->bytes_to_transfer = priv->len; 433 priv->bytes_to_receive = priv->len; 434 435 if (priv->len < 4) 436 zynq_qspi_fill_tx_fifo(priv, priv->len); 437 else 438 zynq_qspi_fill_tx_fifo(priv, priv->fifo_depth); 439 440 writel(ZYNQ_QSPI_IXR_ALL_MASK, ®s->ier); 441 442 /* wait for completion */ 443 do { 444 data = zynq_qspi_irq_poll(priv); 445 } while (data == 0); 446 447 return (priv->len) - (priv->bytes_to_transfer); 448 } 449 450 static int zynq_qspi_transfer(struct zynq_qspi_priv *priv) 451 { 452 unsigned cs_change = 1; 453 int status = 0; 454 455 while (1) { 456 /* Select the chip if required */ 457 if (cs_change) 458 zynq_qspi_chipselect(priv, 1); 459 460 cs_change = priv->cs_change; 461 462 if (!priv->tx_buf && !priv->rx_buf && priv->len) { 463 status = -1; 464 break; 465 } 466 467 /* Request the transfer */ 468 if (priv->len) { 469 status = zynq_qspi_start_transfer(priv); 470 priv->is_inst = 0; 471 } 472 473 if (status != priv->len) { 474 if (status > 0) 475 status = -EMSGSIZE; 476 debug("zynq_qspi_transfer:%d len:%d\n", 477 status, priv->len); 478 break; 479 } 480 status = 0; 481 482 if (cs_change) 483 /* Deselect the chip */ 484 zynq_qspi_chipselect(priv, 0); 485 486 break; 487 } 488 489 return status; 490 } 491 492 static int zynq_qspi_claim_bus(struct udevice *dev) 493 { 494 struct udevice *bus = dev->parent; 495 struct zynq_qspi_priv *priv = dev_get_priv(bus); 496 struct zynq_qspi_regs *regs = priv->regs; 497 498 writel(ZYNQ_QSPI_ENR_SPI_EN_MASK, ®s->enr); 499 500 return 0; 501 } 502 503 static int zynq_qspi_release_bus(struct udevice *dev) 504 { 505 struct udevice *bus = dev->parent; 506 struct zynq_qspi_priv *priv = dev_get_priv(bus); 507 struct zynq_qspi_regs *regs = priv->regs; 508 509 writel(~ZYNQ_QSPI_ENR_SPI_EN_MASK, ®s->enr); 510 511 return 0; 512 } 513 514 static int zynq_qspi_xfer(struct udevice *dev, unsigned int bitlen, 515 const void *dout, void *din, unsigned long flags) 516 { 517 struct udevice *bus = dev->parent; 518 struct zynq_qspi_priv *priv = dev_get_priv(bus); 519 struct dm_spi_slave_platdata *slave_plat = dev_get_parent_platdata(dev); 520 521 priv->cs = slave_plat->cs; 522 priv->tx_buf = dout; 523 priv->rx_buf = din; 524 priv->len = bitlen / 8; 525 526 debug("zynq_qspi_xfer: bus:%i cs:%i bitlen:%i len:%i flags:%lx\n", 527 bus->seq, slave_plat->cs, bitlen, priv->len, flags); 528 529 /* 530 * Festering sore. 531 * Assume that the beginning of a transfer with bits to 532 * transmit must contain a device command. 533 */ 534 if (dout && flags & SPI_XFER_BEGIN) 535 priv->is_inst = 1; 536 else 537 priv->is_inst = 0; 538 539 if (flags & SPI_XFER_END) 540 priv->cs_change = 1; 541 else 542 priv->cs_change = 0; 543 544 zynq_qspi_transfer(priv); 545 546 return 0; 547 } 548 549 static int zynq_qspi_set_speed(struct udevice *bus, uint speed) 550 { 551 struct zynq_qspi_platdata *plat = bus->platdata; 552 struct zynq_qspi_priv *priv = dev_get_priv(bus); 553 struct zynq_qspi_regs *regs = priv->regs; 554 uint32_t confr; 555 u8 baud_rate_val = 0; 556 557 if (speed > plat->frequency) 558 speed = plat->frequency; 559 560 /* Set the clock frequency */ 561 confr = readl(®s->cr); 562 if (speed == 0) { 563 /* Set baudrate x8, if the freq is 0 */ 564 baud_rate_val = 0x2; 565 } else if (plat->speed_hz != speed) { 566 while ((baud_rate_val < ZYNQ_QSPI_CR_BAUD_MAX) && 567 ((plat->frequency / 568 (2 << baud_rate_val)) > speed)) 569 baud_rate_val++; 570 571 plat->speed_hz = speed / (2 << baud_rate_val); 572 } 573 confr &= ~ZYNQ_QSPI_CR_BAUD_MASK; 574 confr |= (baud_rate_val << ZYNQ_QSPI_CR_BAUD_SHIFT); 575 576 writel(confr, ®s->cr); 577 priv->freq = speed; 578 579 debug("%s: regs=%p, speed=%d\n", __func__, priv->regs, priv->freq); 580 581 return 0; 582 } 583 584 static int zynq_qspi_set_mode(struct udevice *bus, uint mode) 585 { 586 struct zynq_qspi_priv *priv = dev_get_priv(bus); 587 struct zynq_qspi_regs *regs = priv->regs; 588 uint32_t confr; 589 590 /* Set the SPI Clock phase and polarities */ 591 confr = readl(®s->cr); 592 confr &= ~(ZYNQ_QSPI_CR_CPHA_MASK | ZYNQ_QSPI_CR_CPOL_MASK); 593 594 if (mode & SPI_CPHA) 595 confr |= ZYNQ_QSPI_CR_CPHA_MASK; 596 if (mode & SPI_CPOL) 597 confr |= ZYNQ_QSPI_CR_CPOL_MASK; 598 599 writel(confr, ®s->cr); 600 priv->mode = mode; 601 602 debug("%s: regs=%p, mode=%d\n", __func__, priv->regs, priv->mode); 603 604 return 0; 605 } 606 607 static const struct dm_spi_ops zynq_qspi_ops = { 608 .claim_bus = zynq_qspi_claim_bus, 609 .release_bus = zynq_qspi_release_bus, 610 .xfer = zynq_qspi_xfer, 611 .set_speed = zynq_qspi_set_speed, 612 .set_mode = zynq_qspi_set_mode, 613 }; 614 615 static const struct udevice_id zynq_qspi_ids[] = { 616 { .compatible = "xlnx,zynq-qspi-1.0" }, 617 { } 618 }; 619 620 U_BOOT_DRIVER(zynq_qspi) = { 621 .name = "zynq_qspi", 622 .id = UCLASS_SPI, 623 .of_match = zynq_qspi_ids, 624 .ops = &zynq_qspi_ops, 625 .ofdata_to_platdata = zynq_qspi_ofdata_to_platdata, 626 .platdata_auto_alloc_size = sizeof(struct zynq_qspi_platdata), 627 .priv_auto_alloc_size = sizeof(struct zynq_qspi_priv), 628 .probe = zynq_qspi_probe, 629 }; 630