1 /* 2 * TI QSPI driver 3 * 4 * Copyright (C) 2013, Texas Instruments, Incorporated 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #include <common.h> 10 #include <asm/io.h> 11 #include <asm/arch/omap.h> 12 #include <malloc.h> 13 #include <spi.h> 14 #include <dm.h> 15 #include <asm/gpio.h> 16 #include <asm/omap_gpio.h> 17 #include <asm/omap_common.h> 18 #include <asm/ti-common/ti-edma3.h> 19 20 DECLARE_GLOBAL_DATA_PTR; 21 22 /* ti qpsi register bit masks */ 23 #define QSPI_TIMEOUT 2000000 24 #define QSPI_FCLK 192000000 25 /* clock control */ 26 #define QSPI_CLK_EN BIT(31) 27 #define QSPI_CLK_DIV_MAX 0xffff 28 /* command */ 29 #define QSPI_EN_CS(n) (n << 28) 30 #define QSPI_WLEN(n) ((n-1) << 19) 31 #define QSPI_3_PIN BIT(18) 32 #define QSPI_RD_SNGL BIT(16) 33 #define QSPI_WR_SNGL (2 << 16) 34 #define QSPI_INVAL (4 << 16) 35 #define QSPI_RD_QUAD (7 << 16) 36 /* device control */ 37 #define QSPI_DD(m, n) (m << (3 + n*8)) 38 #define QSPI_CKPHA(n) (1 << (2 + n*8)) 39 #define QSPI_CSPOL(n) (1 << (1 + n*8)) 40 #define QSPI_CKPOL(n) (1 << (n*8)) 41 /* status */ 42 #define QSPI_WC BIT(1) 43 #define QSPI_BUSY BIT(0) 44 #define QSPI_WC_BUSY (QSPI_WC | QSPI_BUSY) 45 #define QSPI_XFER_DONE QSPI_WC 46 #define MM_SWITCH 0x01 47 #define MEM_CS(cs) ((cs + 1) << 8) 48 #define MEM_CS_UNSELECT 0xfffff0ff 49 #define MMAP_START_ADDR_DRA 0x5c000000 50 #define MMAP_START_ADDR_AM43x 0x30000000 51 #define CORE_CTRL_IO 0x4a002558 52 53 #define QSPI_CMD_READ (0x3 << 0) 54 #define QSPI_CMD_READ_DUAL (0x6b << 0) 55 #define QSPI_CMD_READ_QUAD (0x6c << 0) 56 #define QSPI_CMD_READ_FAST (0x0b << 0) 57 #define QSPI_SETUP0_NUM_A_BYTES (0x3 << 8) 58 #define QSPI_SETUP0_NUM_D_BYTES_NO_BITS (0x0 << 10) 59 #define QSPI_SETUP0_NUM_D_BYTES_8_BITS (0x1 << 10) 60 #define QSPI_SETUP0_READ_NORMAL (0x0 << 12) 61 #define QSPI_SETUP0_READ_DUAL (0x1 << 12) 62 #define QSPI_SETUP0_READ_QUAD (0x3 << 12) 63 #define QSPI_CMD_WRITE (0x12 << 16) 64 #define QSPI_NUM_DUMMY_BITS (0x0 << 24) 65 66 /* ti qspi register set */ 67 struct ti_qspi_regs { 68 u32 pid; 69 u32 pad0[3]; 70 u32 sysconfig; 71 u32 pad1[3]; 72 u32 int_stat_raw; 73 u32 int_stat_en; 74 u32 int_en_set; 75 u32 int_en_ctlr; 76 u32 intc_eoi; 77 u32 pad2[3]; 78 u32 clk_ctrl; 79 u32 dc; 80 u32 cmd; 81 u32 status; 82 u32 data; 83 u32 setup0; 84 u32 setup1; 85 u32 setup2; 86 u32 setup3; 87 u32 memswitch; 88 u32 data1; 89 u32 data2; 90 u32 data3; 91 }; 92 93 /* ti qspi priv */ 94 struct ti_qspi_priv { 95 #ifndef CONFIG_DM_SPI 96 struct spi_slave slave; 97 #else 98 void *memory_map; 99 uint max_hz; 100 u32 num_cs; 101 #endif 102 struct ti_qspi_regs *base; 103 void *ctrl_mod_mmap; 104 unsigned int mode; 105 u32 cmd; 106 u32 dc; 107 }; 108 109 static void ti_spi_set_speed(struct ti_qspi_priv *priv, uint hz) 110 { 111 uint clk_div; 112 113 debug("ti_spi_set_speed: hz: %d, clock divider %d\n", hz, clk_div); 114 115 if (!hz) 116 clk_div = 0; 117 else 118 clk_div = (QSPI_FCLK / hz) - 1; 119 120 /* disable SCLK */ 121 writel(readl(&priv->base->clk_ctrl) & ~QSPI_CLK_EN, 122 &priv->base->clk_ctrl); 123 124 /* assign clk_div values */ 125 if (clk_div < 0) 126 clk_div = 0; 127 else if (clk_div > QSPI_CLK_DIV_MAX) 128 clk_div = QSPI_CLK_DIV_MAX; 129 130 /* enable SCLK */ 131 writel(QSPI_CLK_EN | clk_div, &priv->base->clk_ctrl); 132 } 133 134 static void ti_qspi_cs_deactivate(struct ti_qspi_priv *priv) 135 { 136 writel(priv->cmd | QSPI_INVAL, &priv->base->cmd); 137 /* dummy readl to ensure bus sync */ 138 readl(&priv->base->cmd); 139 } 140 141 static int __ti_qspi_set_mode(struct ti_qspi_priv *priv, unsigned int mode) 142 { 143 priv->dc = 0; 144 if (mode & SPI_CPHA) 145 priv->dc |= QSPI_CKPHA(0); 146 if (mode & SPI_CPOL) 147 priv->dc |= QSPI_CKPOL(0); 148 if (mode & SPI_CS_HIGH) 149 priv->dc |= QSPI_CSPOL(0); 150 151 return 0; 152 } 153 154 static int __ti_qspi_claim_bus(struct ti_qspi_priv *priv, int cs) 155 { 156 writel(priv->dc, &priv->base->dc); 157 writel(0, &priv->base->cmd); 158 writel(0, &priv->base->data); 159 160 priv->dc <<= cs * 8; 161 writel(priv->dc, &priv->base->dc); 162 163 return 0; 164 } 165 166 static void __ti_qspi_release_bus(struct ti_qspi_priv *priv) 167 { 168 writel(0, &priv->base->dc); 169 writel(0, &priv->base->cmd); 170 writel(0, &priv->base->data); 171 } 172 173 static void ti_qspi_ctrl_mode_mmap(void *ctrl_mod_mmap, int cs, bool enable) 174 { 175 u32 val; 176 177 val = readl(ctrl_mod_mmap); 178 if (enable) 179 val |= MEM_CS(cs); 180 else 181 val &= MEM_CS_UNSELECT; 182 writel(val, ctrl_mod_mmap); 183 } 184 185 static int __ti_qspi_xfer(struct ti_qspi_priv *priv, unsigned int bitlen, 186 const void *dout, void *din, unsigned long flags, 187 u32 cs) 188 { 189 uint words = bitlen >> 3; /* fixed 8-bit word length */ 190 const uchar *txp = dout; 191 uchar *rxp = din; 192 uint status; 193 int timeout; 194 195 /* Setup mmap flags */ 196 if (flags & SPI_XFER_MMAP) { 197 writel(MM_SWITCH, &priv->base->memswitch); 198 if (priv->ctrl_mod_mmap) 199 ti_qspi_ctrl_mode_mmap(priv->ctrl_mod_mmap, cs, true); 200 return 0; 201 } else if (flags & SPI_XFER_MMAP_END) { 202 writel(~MM_SWITCH, &priv->base->memswitch); 203 if (priv->ctrl_mod_mmap) 204 ti_qspi_ctrl_mode_mmap(priv->ctrl_mod_mmap, cs, false); 205 return 0; 206 } 207 208 if (bitlen == 0) 209 return -1; 210 211 if (bitlen % 8) { 212 debug("spi_xfer: Non byte aligned SPI transfer\n"); 213 return -1; 214 } 215 216 /* Setup command reg */ 217 priv->cmd = 0; 218 priv->cmd |= QSPI_WLEN(8); 219 priv->cmd |= QSPI_EN_CS(cs); 220 if (priv->mode & SPI_3WIRE) 221 priv->cmd |= QSPI_3_PIN; 222 priv->cmd |= 0xfff; 223 224 /* FIXME: This delay is required for successfull 225 * completion of read/write/erase. Once its root 226 * caused, it will be remove from the driver. 227 */ 228 #ifdef CONFIG_AM43XX 229 udelay(100); 230 #endif 231 while (words--) { 232 if (txp) { 233 debug("tx cmd %08x dc %08x data %02x\n", 234 priv->cmd | QSPI_WR_SNGL, priv->dc, *txp); 235 writel(*txp++, &priv->base->data); 236 writel(priv->cmd | QSPI_WR_SNGL, 237 &priv->base->cmd); 238 status = readl(&priv->base->status); 239 timeout = QSPI_TIMEOUT; 240 while ((status & QSPI_WC_BUSY) != QSPI_XFER_DONE) { 241 if (--timeout < 0) { 242 printf("spi_xfer: TX timeout!\n"); 243 return -1; 244 } 245 status = readl(&priv->base->status); 246 } 247 debug("tx done, status %08x\n", status); 248 } 249 if (rxp) { 250 priv->cmd |= QSPI_RD_SNGL; 251 debug("rx cmd %08x dc %08x\n", 252 priv->cmd, priv->dc); 253 #ifdef CONFIG_DRA7XX 254 udelay(500); 255 #endif 256 writel(priv->cmd, &priv->base->cmd); 257 status = readl(&priv->base->status); 258 timeout = QSPI_TIMEOUT; 259 while ((status & QSPI_WC_BUSY) != QSPI_XFER_DONE) { 260 if (--timeout < 0) { 261 printf("spi_xfer: RX timeout!\n"); 262 return -1; 263 } 264 status = readl(&priv->base->status); 265 } 266 *rxp++ = readl(&priv->base->data); 267 debug("rx done, status %08x, read %02x\n", 268 status, *(rxp-1)); 269 } 270 } 271 272 /* Terminate frame */ 273 if (flags & SPI_XFER_END) 274 ti_qspi_cs_deactivate(priv); 275 276 return 0; 277 } 278 279 /* TODO: control from sf layer to here through dm-spi */ 280 #if defined(CONFIG_TI_EDMA3) && !defined(CONFIG_DMA) 281 void spi_flash_copy_mmap(void *data, void *offset, size_t len) 282 { 283 unsigned int addr = (unsigned int) (data); 284 unsigned int edma_slot_num = 1; 285 286 /* Invalidate the area, so no writeback into the RAM races with DMA */ 287 invalidate_dcache_range(addr, addr + roundup(len, ARCH_DMA_MINALIGN)); 288 289 /* enable edma3 clocks */ 290 enable_edma3_clocks(); 291 292 /* Call edma3 api to do actual DMA transfer */ 293 edma3_transfer(EDMA3_BASE, edma_slot_num, data, offset, len); 294 295 /* disable edma3 clocks */ 296 disable_edma3_clocks(); 297 298 *((unsigned int *)offset) += len; 299 } 300 #endif 301 302 #ifndef CONFIG_DM_SPI 303 304 static inline struct ti_qspi_priv *to_ti_qspi_priv(struct spi_slave *slave) 305 { 306 return container_of(slave, struct ti_qspi_priv, slave); 307 } 308 309 int spi_cs_is_valid(unsigned int bus, unsigned int cs) 310 { 311 return 1; 312 } 313 314 void spi_cs_activate(struct spi_slave *slave) 315 { 316 /* CS handled in xfer */ 317 return; 318 } 319 320 void spi_cs_deactivate(struct spi_slave *slave) 321 { 322 struct ti_qspi_priv *priv = to_ti_qspi_priv(slave); 323 ti_qspi_cs_deactivate(priv); 324 } 325 326 void spi_init(void) 327 { 328 /* nothing to do */ 329 } 330 331 static void ti_spi_setup_spi_register(struct ti_qspi_priv *priv) 332 { 333 u32 memval = 0; 334 335 #ifdef CONFIG_QSPI_QUAD_SUPPORT 336 struct spi_slave *slave = &priv->slave; 337 memval |= (QSPI_CMD_READ_QUAD | QSPI_SETUP0_NUM_A_BYTES | 338 QSPI_SETUP0_NUM_D_BYTES_8_BITS | 339 QSPI_SETUP0_READ_QUAD | QSPI_CMD_WRITE | 340 QSPI_NUM_DUMMY_BITS); 341 slave->mode_rx = SPI_RX_QUAD; 342 #else 343 memval |= QSPI_CMD_READ | QSPI_SETUP0_NUM_A_BYTES | 344 QSPI_SETUP0_NUM_D_BYTES_NO_BITS | 345 QSPI_SETUP0_READ_NORMAL | QSPI_CMD_WRITE | 346 QSPI_NUM_DUMMY_BITS; 347 #endif 348 349 writel(memval, &priv->base->setup0); 350 } 351 352 struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs, 353 unsigned int max_hz, unsigned int mode) 354 { 355 struct ti_qspi_priv *priv; 356 357 #ifdef CONFIG_AM43XX 358 gpio_request(CONFIG_QSPI_SEL_GPIO, "qspi_gpio"); 359 gpio_direction_output(CONFIG_QSPI_SEL_GPIO, 1); 360 #endif 361 362 priv = spi_alloc_slave(struct ti_qspi_priv, bus, cs); 363 if (!priv) { 364 printf("SPI_error: Fail to allocate ti_qspi_priv\n"); 365 return NULL; 366 } 367 368 priv->base = (struct ti_qspi_regs *)QSPI_BASE; 369 priv->mode = mode; 370 #if defined(CONFIG_DRA7XX) || defined(CONFIG_AM57XX) 371 priv->ctrl_mod_mmap = (void *)CORE_CTRL_IO; 372 priv->slave.memory_map = (void *)MMAP_START_ADDR_DRA; 373 #else 374 priv->slave.memory_map = (void *)MMAP_START_ADDR_AM43x; 375 #endif 376 377 ti_spi_set_speed(priv, max_hz); 378 379 #ifdef CONFIG_TI_SPI_MMAP 380 ti_spi_setup_spi_register(priv); 381 #endif 382 383 return &priv->slave; 384 } 385 386 void spi_free_slave(struct spi_slave *slave) 387 { 388 struct ti_qspi_priv *priv = to_ti_qspi_priv(slave); 389 free(priv); 390 } 391 392 int spi_claim_bus(struct spi_slave *slave) 393 { 394 struct ti_qspi_priv *priv = to_ti_qspi_priv(slave); 395 396 debug("%s: bus:%i cs:%i\n", __func__, priv->slave.bus, priv->slave.cs); 397 __ti_qspi_set_mode(priv, priv->mode); 398 return __ti_qspi_claim_bus(priv, priv->slave.cs); 399 } 400 void spi_release_bus(struct spi_slave *slave) 401 { 402 struct ti_qspi_priv *priv = to_ti_qspi_priv(slave); 403 404 debug("%s: bus:%i cs:%i\n", __func__, priv->slave.bus, priv->slave.cs); 405 __ti_qspi_release_bus(priv); 406 } 407 408 int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *dout, 409 void *din, unsigned long flags) 410 { 411 struct ti_qspi_priv *priv = to_ti_qspi_priv(slave); 412 413 debug("spi_xfer: bus:%i cs:%i bitlen:%i flags:%lx\n", 414 priv->slave.bus, priv->slave.cs, bitlen, flags); 415 return __ti_qspi_xfer(priv, bitlen, dout, din, flags, priv->slave.cs); 416 } 417 418 #else /* CONFIG_DM_SPI */ 419 420 static void __ti_qspi_setup_memorymap(struct ti_qspi_priv *priv, 421 struct spi_slave *slave, 422 bool enable) 423 { 424 u32 memval; 425 u32 mode = slave->mode_rx & (SPI_RX_QUAD | SPI_RX_DUAL); 426 427 if (!enable) { 428 writel(0, &priv->base->setup0); 429 return; 430 } 431 432 memval = QSPI_SETUP0_NUM_A_BYTES | QSPI_CMD_WRITE | QSPI_NUM_DUMMY_BITS; 433 434 switch (mode) { 435 case SPI_RX_QUAD: 436 memval |= QSPI_CMD_READ_QUAD; 437 memval |= QSPI_SETUP0_NUM_D_BYTES_8_BITS; 438 memval |= QSPI_SETUP0_READ_QUAD; 439 slave->mode_rx = SPI_RX_QUAD; 440 break; 441 case SPI_RX_DUAL: 442 memval |= QSPI_CMD_READ_DUAL; 443 memval |= QSPI_SETUP0_NUM_D_BYTES_8_BITS; 444 memval |= QSPI_SETUP0_READ_DUAL; 445 break; 446 default: 447 memval |= QSPI_CMD_READ; 448 memval |= QSPI_SETUP0_NUM_D_BYTES_NO_BITS; 449 memval |= QSPI_SETUP0_READ_NORMAL; 450 break; 451 } 452 453 writel(memval, &priv->base->setup0); 454 } 455 456 457 static int ti_qspi_set_speed(struct udevice *bus, uint max_hz) 458 { 459 struct ti_qspi_priv *priv = dev_get_priv(bus); 460 461 ti_spi_set_speed(priv, max_hz); 462 463 return 0; 464 } 465 466 static int ti_qspi_set_mode(struct udevice *bus, uint mode) 467 { 468 struct ti_qspi_priv *priv = dev_get_priv(bus); 469 return __ti_qspi_set_mode(priv, mode); 470 } 471 472 static int ti_qspi_claim_bus(struct udevice *dev) 473 { 474 struct dm_spi_slave_platdata *slave_plat = dev_get_parent_platdata(dev); 475 struct spi_slave *slave = dev_get_parent_priv(dev); 476 struct ti_qspi_priv *priv; 477 struct udevice *bus; 478 479 bus = dev->parent; 480 priv = dev_get_priv(bus); 481 482 if (slave_plat->cs > priv->num_cs) { 483 debug("invalid qspi chip select\n"); 484 return -EINVAL; 485 } 486 487 __ti_qspi_setup_memorymap(priv, slave, true); 488 489 return __ti_qspi_claim_bus(priv, slave_plat->cs); 490 } 491 492 static int ti_qspi_release_bus(struct udevice *dev) 493 { 494 struct spi_slave *slave = dev_get_parent_priv(dev); 495 struct ti_qspi_priv *priv; 496 struct udevice *bus; 497 498 bus = dev->parent; 499 priv = dev_get_priv(bus); 500 501 __ti_qspi_setup_memorymap(priv, slave, false); 502 __ti_qspi_release_bus(priv); 503 504 return 0; 505 } 506 507 static int ti_qspi_xfer(struct udevice *dev, unsigned int bitlen, 508 const void *dout, void *din, unsigned long flags) 509 { 510 struct dm_spi_slave_platdata *slave = dev_get_parent_platdata(dev); 511 struct ti_qspi_priv *priv; 512 struct udevice *bus; 513 514 bus = dev->parent; 515 priv = dev_get_priv(bus); 516 517 if (slave->cs > priv->num_cs) { 518 debug("invalid qspi chip select\n"); 519 return -EINVAL; 520 } 521 522 return __ti_qspi_xfer(priv, bitlen, dout, din, flags, slave->cs); 523 } 524 525 static int ti_qspi_probe(struct udevice *bus) 526 { 527 /* Nothing to do in probe */ 528 return 0; 529 } 530 531 static int ti_qspi_ofdata_to_platdata(struct udevice *bus) 532 { 533 struct ti_qspi_priv *priv = dev_get_priv(bus); 534 const void *blob = gd->fdt_blob; 535 int node = bus->of_offset; 536 fdt_addr_t addr; 537 538 priv->base = (struct ti_qspi_regs *)dev_get_addr(bus); 539 priv->memory_map = (void *)dev_get_addr_index(bus, 1); 540 addr = dev_get_addr_index(bus, 2); 541 priv->ctrl_mod_mmap = (addr == FDT_ADDR_T_NONE) ? NULL : (void *)addr; 542 543 priv->max_hz = fdtdec_get_int(blob, node, "spi-max-frequency", -1); 544 if (priv->max_hz < 0) { 545 debug("Error: Max frequency missing\n"); 546 return -ENODEV; 547 } 548 priv->num_cs = fdtdec_get_int(blob, node, "num-cs", 4); 549 550 debug("%s: regs=<0x%x>, max-frequency=%d\n", __func__, 551 (int)priv->base, priv->max_hz); 552 553 return 0; 554 } 555 556 static int ti_qspi_child_pre_probe(struct udevice *dev) 557 { 558 struct spi_slave *slave = dev_get_parent_priv(dev); 559 struct udevice *bus = dev_get_parent(dev); 560 struct ti_qspi_priv *priv = dev_get_priv(bus); 561 562 slave->memory_map = priv->memory_map; 563 return 0; 564 } 565 566 static const struct dm_spi_ops ti_qspi_ops = { 567 .claim_bus = ti_qspi_claim_bus, 568 .release_bus = ti_qspi_release_bus, 569 .xfer = ti_qspi_xfer, 570 .set_speed = ti_qspi_set_speed, 571 .set_mode = ti_qspi_set_mode, 572 }; 573 574 static const struct udevice_id ti_qspi_ids[] = { 575 { .compatible = "ti,dra7xxx-qspi" }, 576 { .compatible = "ti,am4372-qspi" }, 577 { } 578 }; 579 580 U_BOOT_DRIVER(ti_qspi) = { 581 .name = "ti_qspi", 582 .id = UCLASS_SPI, 583 .of_match = ti_qspi_ids, 584 .ops = &ti_qspi_ops, 585 .ofdata_to_platdata = ti_qspi_ofdata_to_platdata, 586 .priv_auto_alloc_size = sizeof(struct ti_qspi_priv), 587 .probe = ti_qspi_probe, 588 .child_pre_probe = ti_qspi_child_pre_probe, 589 }; 590 #endif /* CONFIG_DM_SPI */ 591