1 /* 2 * TI QSPI driver 3 * 4 * Copyright (C) 2013, Texas Instruments, Incorporated 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #include <common.h> 10 #include <asm/io.h> 11 #include <asm/arch/omap.h> 12 #include <malloc.h> 13 #include <spi.h> 14 #include <dm.h> 15 #include <asm/gpio.h> 16 #include <asm/omap_gpio.h> 17 #include <asm/omap_common.h> 18 #include <asm/ti-common/ti-edma3.h> 19 #include <linux/kernel.h> 20 21 DECLARE_GLOBAL_DATA_PTR; 22 23 /* ti qpsi register bit masks */ 24 #define QSPI_TIMEOUT 2000000 25 #define QSPI_FCLK 192000000 26 #define QSPI_DRA7XX_FCLK 76800000 27 #define QSPI_WLEN_MAX_BITS 128 28 #define QSPI_WLEN_MAX_BYTES (QSPI_WLEN_MAX_BITS >> 3) 29 #define QSPI_WLEN_MASK QSPI_WLEN(QSPI_WLEN_MAX_BITS) 30 /* clock control */ 31 #define QSPI_CLK_EN BIT(31) 32 #define QSPI_CLK_DIV_MAX 0xffff 33 /* command */ 34 #define QSPI_EN_CS(n) (n << 28) 35 #define QSPI_WLEN(n) ((n-1) << 19) 36 #define QSPI_3_PIN BIT(18) 37 #define QSPI_RD_SNGL BIT(16) 38 #define QSPI_WR_SNGL (2 << 16) 39 #define QSPI_INVAL (4 << 16) 40 #define QSPI_RD_QUAD (7 << 16) 41 /* device control */ 42 #define QSPI_DD(m, n) (m << (3 + n*8)) 43 #define QSPI_CKPHA(n) (1 << (2 + n*8)) 44 #define QSPI_CSPOL(n) (1 << (1 + n*8)) 45 #define QSPI_CKPOL(n) (1 << (n*8)) 46 /* status */ 47 #define QSPI_WC BIT(1) 48 #define QSPI_BUSY BIT(0) 49 #define QSPI_WC_BUSY (QSPI_WC | QSPI_BUSY) 50 #define QSPI_XFER_DONE QSPI_WC 51 #define MM_SWITCH 0x01 52 #define MEM_CS(cs) ((cs + 1) << 8) 53 #define MEM_CS_UNSELECT 0xfffff8ff 54 #define MMAP_START_ADDR_DRA 0x5c000000 55 #define MMAP_START_ADDR_AM43x 0x30000000 56 #define CORE_CTRL_IO 0x4a002558 57 58 #define QSPI_CMD_READ (0x3 << 0) 59 #define QSPI_CMD_READ_DUAL (0x6b << 0) 60 #define QSPI_CMD_READ_QUAD (0x6c << 0) 61 #define QSPI_CMD_READ_FAST (0x0b << 0) 62 #define QSPI_SETUP0_NUM_A_BYTES (0x3 << 8) 63 #define QSPI_SETUP0_NUM_D_BYTES_NO_BITS (0x0 << 10) 64 #define QSPI_SETUP0_NUM_D_BYTES_8_BITS (0x1 << 10) 65 #define QSPI_SETUP0_READ_NORMAL (0x0 << 12) 66 #define QSPI_SETUP0_READ_DUAL (0x1 << 12) 67 #define QSPI_SETUP0_READ_QUAD (0x3 << 12) 68 #define QSPI_CMD_WRITE (0x12 << 16) 69 #define QSPI_NUM_DUMMY_BITS (0x0 << 24) 70 71 /* ti qspi register set */ 72 struct ti_qspi_regs { 73 u32 pid; 74 u32 pad0[3]; 75 u32 sysconfig; 76 u32 pad1[3]; 77 u32 int_stat_raw; 78 u32 int_stat_en; 79 u32 int_en_set; 80 u32 int_en_ctlr; 81 u32 intc_eoi; 82 u32 pad2[3]; 83 u32 clk_ctrl; 84 u32 dc; 85 u32 cmd; 86 u32 status; 87 u32 data; 88 u32 setup0; 89 u32 setup1; 90 u32 setup2; 91 u32 setup3; 92 u32 memswitch; 93 u32 data1; 94 u32 data2; 95 u32 data3; 96 }; 97 98 /* ti qspi priv */ 99 struct ti_qspi_priv { 100 #ifndef CONFIG_DM_SPI 101 struct spi_slave slave; 102 #else 103 void *memory_map; 104 uint max_hz; 105 u32 num_cs; 106 #endif 107 struct ti_qspi_regs *base; 108 void *ctrl_mod_mmap; 109 ulong fclk; 110 unsigned int mode; 111 u32 cmd; 112 u32 dc; 113 }; 114 115 static void ti_spi_set_speed(struct ti_qspi_priv *priv, uint hz) 116 { 117 uint clk_div; 118 119 if (!hz) 120 clk_div = 0; 121 else 122 clk_div = DIV_ROUND_UP(priv->fclk, hz) - 1; 123 124 /* truncate clk_div value to QSPI_CLK_DIV_MAX */ 125 if (clk_div > QSPI_CLK_DIV_MAX) 126 clk_div = QSPI_CLK_DIV_MAX; 127 128 debug("ti_spi_set_speed: hz: %d, clock divider %d\n", hz, clk_div); 129 130 /* disable SCLK */ 131 writel(readl(&priv->base->clk_ctrl) & ~QSPI_CLK_EN, 132 &priv->base->clk_ctrl); 133 /* enable SCLK and program the clk divider */ 134 writel(QSPI_CLK_EN | clk_div, &priv->base->clk_ctrl); 135 } 136 137 static void ti_qspi_cs_deactivate(struct ti_qspi_priv *priv) 138 { 139 writel(priv->cmd | QSPI_INVAL, &priv->base->cmd); 140 /* dummy readl to ensure bus sync */ 141 readl(&priv->base->cmd); 142 } 143 144 static int __ti_qspi_set_mode(struct ti_qspi_priv *priv, unsigned int mode) 145 { 146 priv->dc = 0; 147 if (mode & SPI_CPHA) 148 priv->dc |= QSPI_CKPHA(0); 149 if (mode & SPI_CPOL) 150 priv->dc |= QSPI_CKPOL(0); 151 if (mode & SPI_CS_HIGH) 152 priv->dc |= QSPI_CSPOL(0); 153 154 return 0; 155 } 156 157 static int __ti_qspi_claim_bus(struct ti_qspi_priv *priv, int cs) 158 { 159 writel(priv->dc, &priv->base->dc); 160 writel(0, &priv->base->cmd); 161 writel(0, &priv->base->data); 162 163 priv->dc <<= cs * 8; 164 writel(priv->dc, &priv->base->dc); 165 166 return 0; 167 } 168 169 static void __ti_qspi_release_bus(struct ti_qspi_priv *priv) 170 { 171 writel(0, &priv->base->dc); 172 writel(0, &priv->base->cmd); 173 writel(0, &priv->base->data); 174 } 175 176 static void ti_qspi_ctrl_mode_mmap(void *ctrl_mod_mmap, int cs, bool enable) 177 { 178 u32 val; 179 180 val = readl(ctrl_mod_mmap); 181 if (enable) 182 val |= MEM_CS(cs); 183 else 184 val &= MEM_CS_UNSELECT; 185 writel(val, ctrl_mod_mmap); 186 } 187 188 static int __ti_qspi_xfer(struct ti_qspi_priv *priv, unsigned int bitlen, 189 const void *dout, void *din, unsigned long flags, 190 u32 cs) 191 { 192 uint words = bitlen >> 3; /* fixed 8-bit word length */ 193 const uchar *txp = dout; 194 uchar *rxp = din; 195 uint status; 196 int timeout; 197 198 /* Setup mmap flags */ 199 if (flags & SPI_XFER_MMAP) { 200 writel(MM_SWITCH, &priv->base->memswitch); 201 if (priv->ctrl_mod_mmap) 202 ti_qspi_ctrl_mode_mmap(priv->ctrl_mod_mmap, cs, true); 203 return 0; 204 } else if (flags & SPI_XFER_MMAP_END) { 205 writel(~MM_SWITCH, &priv->base->memswitch); 206 if (priv->ctrl_mod_mmap) 207 ti_qspi_ctrl_mode_mmap(priv->ctrl_mod_mmap, cs, false); 208 return 0; 209 } 210 211 if (bitlen == 0) 212 return -1; 213 214 if (bitlen % 8) { 215 debug("spi_xfer: Non byte aligned SPI transfer\n"); 216 return -1; 217 } 218 219 /* Setup command reg */ 220 priv->cmd = 0; 221 priv->cmd |= QSPI_WLEN(8); 222 priv->cmd |= QSPI_EN_CS(cs); 223 if (priv->mode & SPI_3WIRE) 224 priv->cmd |= QSPI_3_PIN; 225 priv->cmd |= 0xfff; 226 227 while (words) { 228 u8 xfer_len = 0; 229 230 if (txp) { 231 u32 cmd = priv->cmd; 232 233 if (words >= QSPI_WLEN_MAX_BYTES) { 234 u32 *txbuf = (u32 *)txp; 235 u32 data; 236 237 data = cpu_to_be32(*txbuf++); 238 writel(data, &priv->base->data3); 239 data = cpu_to_be32(*txbuf++); 240 writel(data, &priv->base->data2); 241 data = cpu_to_be32(*txbuf++); 242 writel(data, &priv->base->data1); 243 data = cpu_to_be32(*txbuf++); 244 writel(data, &priv->base->data); 245 cmd &= ~QSPI_WLEN_MASK; 246 cmd |= QSPI_WLEN(QSPI_WLEN_MAX_BITS); 247 xfer_len = QSPI_WLEN_MAX_BYTES; 248 } else { 249 writeb(*txp, &priv->base->data); 250 xfer_len = 1; 251 } 252 debug("tx cmd %08x dc %08x\n", 253 cmd | QSPI_WR_SNGL, priv->dc); 254 writel(cmd | QSPI_WR_SNGL, &priv->base->cmd); 255 status = readl(&priv->base->status); 256 timeout = QSPI_TIMEOUT; 257 while ((status & QSPI_WC_BUSY) != QSPI_XFER_DONE) { 258 if (--timeout < 0) { 259 printf("spi_xfer: TX timeout!\n"); 260 return -1; 261 } 262 status = readl(&priv->base->status); 263 } 264 txp += xfer_len; 265 debug("tx done, status %08x\n", status); 266 } 267 if (rxp) { 268 debug("rx cmd %08x dc %08x\n", 269 ((u32)(priv->cmd | QSPI_RD_SNGL)), priv->dc); 270 writel(priv->cmd | QSPI_RD_SNGL, &priv->base->cmd); 271 status = readl(&priv->base->status); 272 timeout = QSPI_TIMEOUT; 273 while ((status & QSPI_WC_BUSY) != QSPI_XFER_DONE) { 274 if (--timeout < 0) { 275 printf("spi_xfer: RX timeout!\n"); 276 return -1; 277 } 278 status = readl(&priv->base->status); 279 } 280 *rxp++ = readl(&priv->base->data); 281 xfer_len = 1; 282 debug("rx done, status %08x, read %02x\n", 283 status, *(rxp-1)); 284 } 285 words -= xfer_len; 286 } 287 288 /* Terminate frame */ 289 if (flags & SPI_XFER_END) 290 ti_qspi_cs_deactivate(priv); 291 292 return 0; 293 } 294 295 /* TODO: control from sf layer to here through dm-spi */ 296 #if defined(CONFIG_TI_EDMA3) && !defined(CONFIG_DMA) 297 void spi_flash_copy_mmap(void *data, void *offset, size_t len) 298 { 299 unsigned int addr = (unsigned int) (data); 300 unsigned int edma_slot_num = 1; 301 302 /* Invalidate the area, so no writeback into the RAM races with DMA */ 303 invalidate_dcache_range(addr, addr + roundup(len, ARCH_DMA_MINALIGN)); 304 305 /* enable edma3 clocks */ 306 enable_edma3_clocks(); 307 308 /* Call edma3 api to do actual DMA transfer */ 309 edma3_transfer(EDMA3_BASE, edma_slot_num, data, offset, len); 310 311 /* disable edma3 clocks */ 312 disable_edma3_clocks(); 313 314 *((unsigned int *)offset) += len; 315 } 316 #endif 317 318 #ifndef CONFIG_DM_SPI 319 320 static inline struct ti_qspi_priv *to_ti_qspi_priv(struct spi_slave *slave) 321 { 322 return container_of(slave, struct ti_qspi_priv, slave); 323 } 324 325 int spi_cs_is_valid(unsigned int bus, unsigned int cs) 326 { 327 return 1; 328 } 329 330 void spi_cs_activate(struct spi_slave *slave) 331 { 332 /* CS handled in xfer */ 333 return; 334 } 335 336 void spi_cs_deactivate(struct spi_slave *slave) 337 { 338 struct ti_qspi_priv *priv = to_ti_qspi_priv(slave); 339 ti_qspi_cs_deactivate(priv); 340 } 341 342 void spi_init(void) 343 { 344 /* nothing to do */ 345 } 346 347 static void ti_spi_setup_spi_register(struct ti_qspi_priv *priv) 348 { 349 u32 memval = 0; 350 351 #ifdef CONFIG_QSPI_QUAD_SUPPORT 352 struct spi_slave *slave = &priv->slave; 353 memval |= (QSPI_CMD_READ_QUAD | QSPI_SETUP0_NUM_A_BYTES | 354 QSPI_SETUP0_NUM_D_BYTES_8_BITS | 355 QSPI_SETUP0_READ_QUAD | QSPI_CMD_WRITE | 356 QSPI_NUM_DUMMY_BITS); 357 slave->mode |= SPI_RX_QUAD; 358 #else 359 memval |= QSPI_CMD_READ | QSPI_SETUP0_NUM_A_BYTES | 360 QSPI_SETUP0_NUM_D_BYTES_NO_BITS | 361 QSPI_SETUP0_READ_NORMAL | QSPI_CMD_WRITE | 362 QSPI_NUM_DUMMY_BITS; 363 #endif 364 365 writel(memval, &priv->base->setup0); 366 } 367 368 struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs, 369 unsigned int max_hz, unsigned int mode) 370 { 371 struct ti_qspi_priv *priv; 372 373 #ifdef CONFIG_AM43XX 374 gpio_request(CONFIG_QSPI_SEL_GPIO, "qspi_gpio"); 375 gpio_direction_output(CONFIG_QSPI_SEL_GPIO, 1); 376 #endif 377 378 priv = spi_alloc_slave(struct ti_qspi_priv, bus, cs); 379 if (!priv) { 380 printf("SPI_error: Fail to allocate ti_qspi_priv\n"); 381 return NULL; 382 } 383 384 priv->base = (struct ti_qspi_regs *)QSPI_BASE; 385 priv->mode = mode; 386 #if defined(CONFIG_DRA7XX) || defined(CONFIG_AM57XX) 387 priv->ctrl_mod_mmap = (void *)CORE_CTRL_IO; 388 priv->slave.memory_map = (void *)MMAP_START_ADDR_DRA; 389 priv->fclk = QSPI_DRA7XX_FCLK; 390 #else 391 priv->slave.memory_map = (void *)MMAP_START_ADDR_AM43x; 392 priv->fclk = QSPI_FCLK; 393 #endif 394 395 ti_spi_set_speed(priv, max_hz); 396 397 #ifdef CONFIG_TI_SPI_MMAP 398 ti_spi_setup_spi_register(priv); 399 #endif 400 401 return &priv->slave; 402 } 403 404 void spi_free_slave(struct spi_slave *slave) 405 { 406 struct ti_qspi_priv *priv = to_ti_qspi_priv(slave); 407 free(priv); 408 } 409 410 int spi_claim_bus(struct spi_slave *slave) 411 { 412 struct ti_qspi_priv *priv = to_ti_qspi_priv(slave); 413 414 debug("%s: bus:%i cs:%i\n", __func__, priv->slave.bus, priv->slave.cs); 415 __ti_qspi_set_mode(priv, priv->mode); 416 return __ti_qspi_claim_bus(priv, priv->slave.cs); 417 } 418 void spi_release_bus(struct spi_slave *slave) 419 { 420 struct ti_qspi_priv *priv = to_ti_qspi_priv(slave); 421 422 debug("%s: bus:%i cs:%i\n", __func__, priv->slave.bus, priv->slave.cs); 423 __ti_qspi_release_bus(priv); 424 } 425 426 int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *dout, 427 void *din, unsigned long flags) 428 { 429 struct ti_qspi_priv *priv = to_ti_qspi_priv(slave); 430 431 debug("spi_xfer: bus:%i cs:%i bitlen:%i flags:%lx\n", 432 priv->slave.bus, priv->slave.cs, bitlen, flags); 433 return __ti_qspi_xfer(priv, bitlen, dout, din, flags, priv->slave.cs); 434 } 435 436 #else /* CONFIG_DM_SPI */ 437 438 static void __ti_qspi_setup_memorymap(struct ti_qspi_priv *priv, 439 struct spi_slave *slave, 440 bool enable) 441 { 442 u32 memval; 443 u32 mode = slave->mode & (SPI_RX_QUAD | SPI_RX_DUAL); 444 445 if (!enable) { 446 writel(0, &priv->base->setup0); 447 return; 448 } 449 450 memval = QSPI_SETUP0_NUM_A_BYTES | QSPI_CMD_WRITE | QSPI_NUM_DUMMY_BITS; 451 452 switch (mode) { 453 case SPI_RX_QUAD: 454 memval |= QSPI_CMD_READ_QUAD; 455 memval |= QSPI_SETUP0_NUM_D_BYTES_8_BITS; 456 memval |= QSPI_SETUP0_READ_QUAD; 457 slave->mode |= SPI_RX_QUAD; 458 break; 459 case SPI_RX_DUAL: 460 memval |= QSPI_CMD_READ_DUAL; 461 memval |= QSPI_SETUP0_NUM_D_BYTES_8_BITS; 462 memval |= QSPI_SETUP0_READ_DUAL; 463 break; 464 default: 465 memval |= QSPI_CMD_READ; 466 memval |= QSPI_SETUP0_NUM_D_BYTES_NO_BITS; 467 memval |= QSPI_SETUP0_READ_NORMAL; 468 break; 469 } 470 471 writel(memval, &priv->base->setup0); 472 } 473 474 475 static int ti_qspi_set_speed(struct udevice *bus, uint max_hz) 476 { 477 struct ti_qspi_priv *priv = dev_get_priv(bus); 478 479 ti_spi_set_speed(priv, max_hz); 480 481 return 0; 482 } 483 484 static int ti_qspi_set_mode(struct udevice *bus, uint mode) 485 { 486 struct ti_qspi_priv *priv = dev_get_priv(bus); 487 return __ti_qspi_set_mode(priv, mode); 488 } 489 490 static int ti_qspi_claim_bus(struct udevice *dev) 491 { 492 struct dm_spi_slave_platdata *slave_plat = dev_get_parent_platdata(dev); 493 struct spi_slave *slave = dev_get_parent_priv(dev); 494 struct ti_qspi_priv *priv; 495 struct udevice *bus; 496 497 bus = dev->parent; 498 priv = dev_get_priv(bus); 499 500 if (slave_plat->cs > priv->num_cs) { 501 debug("invalid qspi chip select\n"); 502 return -EINVAL; 503 } 504 505 __ti_qspi_setup_memorymap(priv, slave, true); 506 507 return __ti_qspi_claim_bus(priv, slave_plat->cs); 508 } 509 510 static int ti_qspi_release_bus(struct udevice *dev) 511 { 512 struct spi_slave *slave = dev_get_parent_priv(dev); 513 struct ti_qspi_priv *priv; 514 struct udevice *bus; 515 516 bus = dev->parent; 517 priv = dev_get_priv(bus); 518 519 __ti_qspi_setup_memorymap(priv, slave, false); 520 __ti_qspi_release_bus(priv); 521 522 return 0; 523 } 524 525 static int ti_qspi_xfer(struct udevice *dev, unsigned int bitlen, 526 const void *dout, void *din, unsigned long flags) 527 { 528 struct dm_spi_slave_platdata *slave = dev_get_parent_platdata(dev); 529 struct ti_qspi_priv *priv; 530 struct udevice *bus; 531 532 bus = dev->parent; 533 priv = dev_get_priv(bus); 534 535 if (slave->cs > priv->num_cs) { 536 debug("invalid qspi chip select\n"); 537 return -EINVAL; 538 } 539 540 return __ti_qspi_xfer(priv, bitlen, dout, din, flags, slave->cs); 541 } 542 543 static int ti_qspi_probe(struct udevice *bus) 544 { 545 struct ti_qspi_priv *priv = dev_get_priv(bus); 546 547 priv->fclk = dev_get_driver_data(bus); 548 549 return 0; 550 } 551 552 static int ti_qspi_ofdata_to_platdata(struct udevice *bus) 553 { 554 struct ti_qspi_priv *priv = dev_get_priv(bus); 555 const void *blob = gd->fdt_blob; 556 int node = bus->of_offset; 557 fdt_addr_t addr; 558 void *mmap; 559 560 priv->base = map_physmem(dev_get_addr(bus), sizeof(struct ti_qspi_regs), 561 MAP_NOCACHE); 562 priv->memory_map = map_physmem(dev_get_addr_index(bus, 1), 0, 563 MAP_NOCACHE); 564 addr = dev_get_addr_index(bus, 2); 565 mmap = map_physmem(dev_get_addr_index(bus, 2), 0, MAP_NOCACHE); 566 priv->ctrl_mod_mmap = (addr == FDT_ADDR_T_NONE) ? NULL : mmap; 567 568 priv->max_hz = fdtdec_get_int(blob, node, "spi-max-frequency", -1); 569 if (priv->max_hz < 0) { 570 debug("Error: Max frequency missing\n"); 571 return -ENODEV; 572 } 573 priv->num_cs = fdtdec_get_int(blob, node, "num-cs", 4); 574 575 debug("%s: regs=<0x%x>, max-frequency=%d\n", __func__, 576 (int)priv->base, priv->max_hz); 577 578 return 0; 579 } 580 581 static int ti_qspi_child_pre_probe(struct udevice *dev) 582 { 583 struct spi_slave *slave = dev_get_parent_priv(dev); 584 struct udevice *bus = dev_get_parent(dev); 585 struct ti_qspi_priv *priv = dev_get_priv(bus); 586 587 slave->memory_map = priv->memory_map; 588 return 0; 589 } 590 591 static const struct dm_spi_ops ti_qspi_ops = { 592 .claim_bus = ti_qspi_claim_bus, 593 .release_bus = ti_qspi_release_bus, 594 .xfer = ti_qspi_xfer, 595 .set_speed = ti_qspi_set_speed, 596 .set_mode = ti_qspi_set_mode, 597 }; 598 599 static const struct udevice_id ti_qspi_ids[] = { 600 { .compatible = "ti,dra7xxx-qspi", .data = QSPI_DRA7XX_FCLK}, 601 { .compatible = "ti,am4372-qspi", .data = QSPI_FCLK}, 602 { } 603 }; 604 605 U_BOOT_DRIVER(ti_qspi) = { 606 .name = "ti_qspi", 607 .id = UCLASS_SPI, 608 .of_match = ti_qspi_ids, 609 .ops = &ti_qspi_ops, 610 .ofdata_to_platdata = ti_qspi_ofdata_to_platdata, 611 .priv_auto_alloc_size = sizeof(struct ti_qspi_priv), 612 .probe = ti_qspi_probe, 613 .child_pre_probe = ti_qspi_child_pre_probe, 614 }; 615 #endif /* CONFIG_DM_SPI */ 616