1 /* 2 * Copyright (c) 2010-2013 NVIDIA Corporation 3 * With help from the mpc8xxx SPI driver 4 * With more help from omap3_spi SPI driver 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #include <common.h> 10 #include <malloc.h> 11 #include <asm/io.h> 12 #include <asm/gpio.h> 13 #include <asm/arch/clock.h> 14 #include <asm/arch/pinmux.h> 15 #include <asm/arch-tegra/clk_rst.h> 16 #include <asm/arch-tegra20/tegra20_sflash.h> 17 #include <spi.h> 18 #include <fdtdec.h> 19 20 DECLARE_GLOBAL_DATA_PTR; 21 22 #define SPI_CMD_GO (1 << 30) 23 #define SPI_CMD_ACTIVE_SCLK_SHIFT 26 24 #define SPI_CMD_ACTIVE_SCLK_MASK (3 << SPI_CMD_ACTIVE_SCLK_SHIFT) 25 #define SPI_CMD_CK_SDA (1 << 21) 26 #define SPI_CMD_ACTIVE_SDA_SHIFT 18 27 #define SPI_CMD_ACTIVE_SDA_MASK (3 << SPI_CMD_ACTIVE_SDA_SHIFT) 28 #define SPI_CMD_CS_POL (1 << 16) 29 #define SPI_CMD_TXEN (1 << 15) 30 #define SPI_CMD_RXEN (1 << 14) 31 #define SPI_CMD_CS_VAL (1 << 13) 32 #define SPI_CMD_CS_SOFT (1 << 12) 33 #define SPI_CMD_CS_DELAY (1 << 9) 34 #define SPI_CMD_CS3_EN (1 << 8) 35 #define SPI_CMD_CS2_EN (1 << 7) 36 #define SPI_CMD_CS1_EN (1 << 6) 37 #define SPI_CMD_CS0_EN (1 << 5) 38 #define SPI_CMD_BIT_LENGTH (1 << 4) 39 #define SPI_CMD_BIT_LENGTH_MASK 0x0000001F 40 41 #define SPI_STAT_BSY (1 << 31) 42 #define SPI_STAT_RDY (1 << 30) 43 #define SPI_STAT_RXF_FLUSH (1 << 29) 44 #define SPI_STAT_TXF_FLUSH (1 << 28) 45 #define SPI_STAT_RXF_UNR (1 << 27) 46 #define SPI_STAT_TXF_OVF (1 << 26) 47 #define SPI_STAT_RXF_EMPTY (1 << 25) 48 #define SPI_STAT_RXF_FULL (1 << 24) 49 #define SPI_STAT_TXF_EMPTY (1 << 23) 50 #define SPI_STAT_TXF_FULL (1 << 22) 51 #define SPI_STAT_SEL_TXRX_N (1 << 16) 52 #define SPI_STAT_CUR_BLKCNT (1 << 15) 53 54 #define SPI_TIMEOUT 1000 55 #define TEGRA_SPI_MAX_FREQ 52000000 56 57 struct spi_regs { 58 u32 command; /* SPI_COMMAND_0 register */ 59 u32 status; /* SPI_STATUS_0 register */ 60 u32 rx_cmp; /* SPI_RX_CMP_0 register */ 61 u32 dma_ctl; /* SPI_DMA_CTL_0 register */ 62 u32 tx_fifo; /* SPI_TX_FIFO_0 register */ 63 u32 rsvd[3]; /* offsets 0x14 to 0x1F reserved */ 64 u32 rx_fifo; /* SPI_RX_FIFO_0 register */ 65 }; 66 67 struct tegra_spi_ctrl { 68 struct spi_regs *regs; 69 unsigned int freq; 70 unsigned int mode; 71 int periph_id; 72 int valid; 73 }; 74 75 struct tegra_spi_slave { 76 struct spi_slave slave; 77 struct tegra_spi_ctrl *ctrl; 78 }; 79 80 /* tegra20 only supports one SFLASH controller */ 81 static struct tegra_spi_ctrl spi_ctrls[1]; 82 83 static inline struct tegra_spi_slave *to_tegra_spi(struct spi_slave *slave) 84 { 85 return container_of(slave, struct tegra_spi_slave, slave); 86 } 87 88 int tegra20_spi_cs_is_valid(unsigned int bus, unsigned int cs) 89 { 90 /* Tegra20 SPI-Flash - only 1 device ('bus/cs') */ 91 if (bus != 0 || cs != 0) 92 return 0; 93 else 94 return 1; 95 } 96 97 struct spi_slave *tegra20_spi_setup_slave(unsigned int bus, unsigned int cs, 98 unsigned int max_hz, unsigned int mode) 99 { 100 struct tegra_spi_slave *spi; 101 102 if (!spi_cs_is_valid(bus, cs)) { 103 printf("SPI error: unsupported bus %d / chip select %d\n", 104 bus, cs); 105 return NULL; 106 } 107 108 if (max_hz > TEGRA_SPI_MAX_FREQ) { 109 printf("SPI error: unsupported frequency %d Hz. Max frequency" 110 " is %d Hz\n", max_hz, TEGRA_SPI_MAX_FREQ); 111 return NULL; 112 } 113 114 spi = spi_alloc_slave(struct tegra_spi_slave, bus, cs); 115 if (!spi) { 116 printf("SPI error: malloc of SPI structure failed\n"); 117 return NULL; 118 } 119 spi->ctrl = &spi_ctrls[bus]; 120 if (!spi->ctrl) { 121 printf("SPI error: could not find controller for bus %d\n", 122 bus); 123 return NULL; 124 } 125 126 if (max_hz < spi->ctrl->freq) { 127 debug("%s: limiting frequency from %u to %u\n", __func__, 128 spi->ctrl->freq, max_hz); 129 spi->ctrl->freq = max_hz; 130 } 131 spi->ctrl->mode = mode; 132 133 return &spi->slave; 134 } 135 136 void tegra20_spi_free_slave(struct spi_slave *slave) 137 { 138 struct tegra_spi_slave *spi = to_tegra_spi(slave); 139 140 free(spi); 141 } 142 143 int tegra20_spi_init(int *node_list, int count) 144 { 145 struct tegra_spi_ctrl *ctrl; 146 int i; 147 int node = 0; 148 int found = 0; 149 150 for (i = 0; i < count; i++) { 151 ctrl = &spi_ctrls[i]; 152 node = node_list[i]; 153 154 ctrl->regs = (struct spi_regs *)fdtdec_get_addr(gd->fdt_blob, 155 node, "reg"); 156 if ((fdt_addr_t)ctrl->regs == FDT_ADDR_T_NONE) { 157 debug("%s: no slink register found\n", __func__); 158 continue; 159 } 160 ctrl->freq = fdtdec_get_int(gd->fdt_blob, node, 161 "spi-max-frequency", 0); 162 if (!ctrl->freq) { 163 debug("%s: no slink max frequency found\n", __func__); 164 continue; 165 } 166 167 ctrl->periph_id = clock_decode_periph_id(gd->fdt_blob, node); 168 if (ctrl->periph_id == PERIPH_ID_NONE) { 169 debug("%s: could not decode periph id\n", __func__); 170 continue; 171 } 172 ctrl->valid = 1; 173 found = 1; 174 175 debug("%s: found controller at %p, freq = %u, periph_id = %d\n", 176 __func__, ctrl->regs, ctrl->freq, ctrl->periph_id); 177 } 178 return !found; 179 } 180 181 int tegra20_spi_claim_bus(struct spi_slave *slave) 182 { 183 struct tegra_spi_slave *spi = to_tegra_spi(slave); 184 struct spi_regs *regs = spi->ctrl->regs; 185 u32 reg; 186 187 /* Change SPI clock to correct frequency, PLLP_OUT0 source */ 188 clock_start_periph_pll(spi->ctrl->periph_id, CLOCK_ID_PERIPH, 189 spi->ctrl->freq); 190 191 /* Clear stale status here */ 192 reg = SPI_STAT_RDY | SPI_STAT_RXF_FLUSH | SPI_STAT_TXF_FLUSH | \ 193 SPI_STAT_RXF_UNR | SPI_STAT_TXF_OVF; 194 writel(reg, ®s->status); 195 debug("%s: STATUS = %08x\n", __func__, readl(®s->status)); 196 197 /* 198 * Use sw-controlled CS, so we can clock in data after ReadID, etc. 199 */ 200 reg = (spi->ctrl->mode & 1) << SPI_CMD_ACTIVE_SDA_SHIFT; 201 if (spi->ctrl->mode & 2) 202 reg |= 1 << SPI_CMD_ACTIVE_SCLK_SHIFT; 203 clrsetbits_le32(®s->command, SPI_CMD_ACTIVE_SCLK_MASK | 204 SPI_CMD_ACTIVE_SDA_MASK, SPI_CMD_CS_SOFT | reg); 205 debug("%s: COMMAND = %08x\n", __func__, readl(®s->command)); 206 207 /* 208 * SPI pins on Tegra20 are muxed - change pinmux later due to UART 209 * issue. 210 */ 211 pinmux_set_func(PMUX_PINGRP_GMD, PMUX_FUNC_SFLASH); 212 pinmux_tristate_disable(PMUX_PINGRP_LSPI); 213 pinmux_set_func(PMUX_PINGRP_GMC, PMUX_FUNC_SFLASH); 214 215 return 0; 216 } 217 218 void tegra20_spi_cs_activate(struct spi_slave *slave) 219 { 220 struct tegra_spi_slave *spi = to_tegra_spi(slave); 221 struct spi_regs *regs = spi->ctrl->regs; 222 223 /* CS is negated on Tegra, so drive a 1 to get a 0 */ 224 setbits_le32(®s->command, SPI_CMD_CS_VAL); 225 } 226 227 void tegra20_spi_cs_deactivate(struct spi_slave *slave) 228 { 229 struct tegra_spi_slave *spi = to_tegra_spi(slave); 230 struct spi_regs *regs = spi->ctrl->regs; 231 232 /* CS is negated on Tegra, so drive a 0 to get a 1 */ 233 clrbits_le32(®s->command, SPI_CMD_CS_VAL); 234 } 235 236 int tegra20_spi_xfer(struct spi_slave *slave, unsigned int bitlen, 237 const void *data_out, void *data_in, unsigned long flags) 238 { 239 struct tegra_spi_slave *spi = to_tegra_spi(slave); 240 struct spi_regs *regs = spi->ctrl->regs; 241 u32 reg, tmpdout, tmpdin = 0; 242 const u8 *dout = data_out; 243 u8 *din = data_in; 244 int num_bytes; 245 int ret; 246 247 debug("spi_xfer: slave %u:%u dout %08X din %08X bitlen %u\n", 248 slave->bus, slave->cs, *(u8 *)dout, *(u8 *)din, bitlen); 249 if (bitlen % 8) 250 return -1; 251 num_bytes = bitlen / 8; 252 253 ret = 0; 254 255 reg = readl(®s->status); 256 writel(reg, ®s->status); /* Clear all SPI events via R/W */ 257 debug("spi_xfer entry: STATUS = %08x\n", reg); 258 259 reg = readl(®s->command); 260 reg |= SPI_CMD_TXEN | SPI_CMD_RXEN; 261 writel(reg, ®s->command); 262 debug("spi_xfer: COMMAND = %08x\n", readl(®s->command)); 263 264 if (flags & SPI_XFER_BEGIN) 265 spi_cs_activate(slave); 266 267 /* handle data in 32-bit chunks */ 268 while (num_bytes > 0) { 269 int bytes; 270 int is_read = 0; 271 int tm, i; 272 273 tmpdout = 0; 274 bytes = (num_bytes > 4) ? 4 : num_bytes; 275 276 if (dout != NULL) { 277 for (i = 0; i < bytes; ++i) 278 tmpdout = (tmpdout << 8) | dout[i]; 279 } 280 281 num_bytes -= bytes; 282 if (dout) 283 dout += bytes; 284 285 clrsetbits_le32(®s->command, SPI_CMD_BIT_LENGTH_MASK, 286 bytes * 8 - 1); 287 writel(tmpdout, ®s->tx_fifo); 288 setbits_le32(®s->command, SPI_CMD_GO); 289 290 /* 291 * Wait for SPI transmit FIFO to empty, or to time out. 292 * The RX FIFO status will be read and cleared last 293 */ 294 for (tm = 0, is_read = 0; tm < SPI_TIMEOUT; ++tm) { 295 u32 status; 296 297 status = readl(®s->status); 298 299 /* We can exit when we've had both RX and TX activity */ 300 if (is_read && (status & SPI_STAT_TXF_EMPTY)) 301 break; 302 303 if ((status & (SPI_STAT_BSY | SPI_STAT_RDY)) != 304 SPI_STAT_RDY) 305 tm++; 306 307 else if (!(status & SPI_STAT_RXF_EMPTY)) { 308 tmpdin = readl(®s->rx_fifo); 309 is_read = 1; 310 311 /* swap bytes read in */ 312 if (din != NULL) { 313 for (i = bytes - 1; i >= 0; --i) { 314 din[i] = tmpdin & 0xff; 315 tmpdin >>= 8; 316 } 317 din += bytes; 318 } 319 } 320 } 321 322 if (tm >= SPI_TIMEOUT) 323 ret = tm; 324 325 /* clear ACK RDY, etc. bits */ 326 writel(readl(®s->status), ®s->status); 327 } 328 329 if (flags & SPI_XFER_END) 330 spi_cs_deactivate(slave); 331 332 debug("spi_xfer: transfer ended. Value=%08x, status = %08x\n", 333 tmpdin, readl(®s->status)); 334 335 if (ret) { 336 printf("spi_xfer: timeout during SPI transfer, tm %d\n", ret); 337 return -1; 338 } 339 340 return 0; 341 } 342