xref: /openbmc/u-boot/drivers/spi/sh_qspi.c (revision 5396b2a9)
1 // SPDX-License-Identifier: GPL-2.0
2 /*
3  * SH QSPI (Quad SPI) driver
4  *
5  * Copyright (C) 2013 Renesas Electronics Corporation
6  * Copyright (C) 2013 Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
7  */
8 
9 #include <common.h>
10 #include <console.h>
11 #include <malloc.h>
12 #include <spi.h>
13 #include <wait_bit.h>
14 #include <asm/arch/rmobile.h>
15 #include <asm/io.h>
16 
17 /* SH QSPI register bit masks <REG>_<BIT> */
18 #define SPCR_MSTR	0x08
19 #define SPCR_SPE	0x40
20 #define SPSR_SPRFF	0x80
21 #define SPSR_SPTEF	0x20
22 #define SPPCR_IO3FV	0x04
23 #define SPPCR_IO2FV	0x02
24 #define SPPCR_IO1FV	0x01
25 #define SPBDCR_RXBC0	BIT(0)
26 #define SPCMD_SCKDEN	BIT(15)
27 #define SPCMD_SLNDEN	BIT(14)
28 #define SPCMD_SPNDEN	BIT(13)
29 #define SPCMD_SSLKP	BIT(7)
30 #define SPCMD_BRDV0	BIT(2)
31 #define SPCMD_INIT1	SPCMD_SCKDEN | SPCMD_SLNDEN | \
32 			SPCMD_SPNDEN | SPCMD_SSLKP | \
33 			SPCMD_BRDV0
34 #define SPCMD_INIT2	SPCMD_SPNDEN | SPCMD_SSLKP | \
35 			SPCMD_BRDV0
36 #define SPBFCR_TXRST	BIT(7)
37 #define SPBFCR_RXRST	BIT(6)
38 #define SPBFCR_TXTRG	0x30
39 #define SPBFCR_RXTRG	0x07
40 
41 /* SH QSPI register set */
42 struct sh_qspi_regs {
43 	u8	spcr;
44 	u8	sslp;
45 	u8	sppcr;
46 	u8	spsr;
47 	u32	spdr;
48 	u8	spscr;
49 	u8	spssr;
50 	u8	spbr;
51 	u8	spdcr;
52 	u8	spckd;
53 	u8	sslnd;
54 	u8	spnd;
55 	u8	dummy0;
56 	u16	spcmd0;
57 	u16	spcmd1;
58 	u16	spcmd2;
59 	u16	spcmd3;
60 	u8	spbfcr;
61 	u8	dummy1;
62 	u16	spbdcr;
63 	u32	spbmul0;
64 	u32	spbmul1;
65 	u32	spbmul2;
66 	u32	spbmul3;
67 };
68 
69 struct sh_qspi_slave {
70 #ifndef CONFIG_DM_SPI
71 	struct spi_slave	slave;
72 #endif
73 	struct sh_qspi_regs	*regs;
74 };
75 
76 static void sh_qspi_init(struct sh_qspi_slave *ss)
77 {
78 	/* QSPI initialize */
79 	/* Set master mode only */
80 	writeb(SPCR_MSTR, &ss->regs->spcr);
81 
82 	/* Set SSL signal level */
83 	writeb(0x00, &ss->regs->sslp);
84 
85 	/* Set MOSI signal value when transfer is in idle state */
86 	writeb(SPPCR_IO3FV|SPPCR_IO2FV, &ss->regs->sppcr);
87 
88 	/* Set bit rate. See 58.3.8 Quad Serial Peripheral Interface */
89 	writeb(0x01, &ss->regs->spbr);
90 
91 	/* Disable Dummy Data Transmission */
92 	writeb(0x00, &ss->regs->spdcr);
93 
94 	/* Set clock delay value */
95 	writeb(0x00, &ss->regs->spckd);
96 
97 	/* Set SSL negation delay value */
98 	writeb(0x00, &ss->regs->sslnd);
99 
100 	/* Set next-access delay value */
101 	writeb(0x00, &ss->regs->spnd);
102 
103 	/* Set equence command */
104 	writew(SPCMD_INIT2, &ss->regs->spcmd0);
105 
106 	/* Reset transfer and receive Buffer */
107 	setbits_8(&ss->regs->spbfcr, SPBFCR_TXRST|SPBFCR_RXRST);
108 
109 	/* Clear transfer and receive Buffer control bit */
110 	clrbits_8(&ss->regs->spbfcr, SPBFCR_TXRST|SPBFCR_RXRST);
111 
112 	/* Set equence control method. Use equence0 only */
113 	writeb(0x00, &ss->regs->spscr);
114 
115 	/* Enable SPI function */
116 	setbits_8(&ss->regs->spcr, SPCR_SPE);
117 }
118 
119 static void sh_qspi_cs_activate(struct sh_qspi_slave *ss)
120 {
121 	/* Set master mode only */
122 	writeb(SPCR_MSTR, &ss->regs->spcr);
123 
124 	/* Set command */
125 	writew(SPCMD_INIT1, &ss->regs->spcmd0);
126 
127 	/* Reset transfer and receive Buffer */
128 	setbits_8(&ss->regs->spbfcr, SPBFCR_TXRST|SPBFCR_RXRST);
129 
130 	/* Clear transfer and receive Buffer control bit */
131 	clrbits_8(&ss->regs->spbfcr, SPBFCR_TXRST|SPBFCR_RXRST);
132 
133 	/* Set equence control method. Use equence0 only */
134 	writeb(0x00, &ss->regs->spscr);
135 
136 	/* Enable SPI function */
137 	setbits_8(&ss->regs->spcr, SPCR_SPE);
138 }
139 
140 static void sh_qspi_cs_deactivate(struct sh_qspi_slave *ss)
141 {
142 	/* Disable SPI Function */
143 	clrbits_8(&ss->regs->spcr, SPCR_SPE);
144 }
145 
146 static int sh_qspi_xfer_common(struct sh_qspi_slave *ss, unsigned int bitlen,
147 			       const void *dout, void *din, unsigned long flags)
148 {
149 	u32 nbyte, chunk;
150 	int i, ret = 0;
151 	u8 dtdata = 0, drdata;
152 	u8 *tdata = &dtdata, *rdata = &drdata;
153 	u32 *spbmul0 = &ss->regs->spbmul0;
154 
155 	if (dout == NULL && din == NULL) {
156 		if (flags & SPI_XFER_END)
157 			sh_qspi_cs_deactivate(ss);
158 		return 0;
159 	}
160 
161 	if (bitlen % 8) {
162 		printf("%s: bitlen is not 8bit alined %d", __func__, bitlen);
163 		return 1;
164 	}
165 
166 	nbyte = bitlen / 8;
167 
168 	if (flags & SPI_XFER_BEGIN) {
169 		sh_qspi_cs_activate(ss);
170 
171 		/* Set 1048576 byte */
172 		writel(0x100000, spbmul0);
173 	}
174 
175 	if (flags & SPI_XFER_END)
176 		writel(nbyte, spbmul0);
177 
178 	if (dout != NULL)
179 		tdata = (u8 *)dout;
180 
181 	if (din != NULL)
182 		rdata = din;
183 
184 	while (nbyte > 0) {
185 		/*
186 		 * Check if there is 32 Byte chunk and if there is, transfer
187 		 * it in one burst, otherwise transfer on byte-by-byte basis.
188 		 */
189 		chunk = (nbyte >= 32) ? 32 : 1;
190 
191 		clrsetbits_8(&ss->regs->spbfcr, SPBFCR_TXTRG | SPBFCR_RXTRG,
192 			     chunk == 32 ? SPBFCR_TXTRG | SPBFCR_RXTRG : 0);
193 
194 		ret = wait_for_bit_8(&ss->regs->spsr, SPSR_SPTEF,
195 				     true, 1000, true);
196 		if (ret)
197 			return ret;
198 
199 		for (i = 0; i < chunk; i++) {
200 			writeb(*tdata, &ss->regs->spdr);
201 			if (dout != NULL)
202 				tdata++;
203 		}
204 
205 		ret = wait_for_bit_8(&ss->regs->spsr, SPSR_SPRFF,
206 				     true, 1000, true);
207 		if (ret)
208 			return ret;
209 
210 		for (i = 0; i < chunk; i++) {
211 			*rdata = readb(&ss->regs->spdr);
212 			if (din != NULL)
213 				rdata++;
214 		}
215 
216 		nbyte -= chunk;
217 	}
218 
219 	if (flags & SPI_XFER_END)
220 		sh_qspi_cs_deactivate(ss);
221 
222 	return ret;
223 }
224 
225 #ifndef CONFIG_DM_SPI
226 static inline struct sh_qspi_slave *to_sh_qspi(struct spi_slave *slave)
227 {
228 	return container_of(slave, struct sh_qspi_slave, slave);
229 }
230 
231 int spi_cs_is_valid(unsigned int bus, unsigned int cs)
232 {
233 	return 1;
234 }
235 
236 void spi_cs_activate(struct spi_slave *slave)
237 {
238 	struct sh_qspi_slave *ss = to_sh_qspi(slave);
239 
240 	sh_qspi_cs_activate(ss);
241 }
242 
243 void spi_cs_deactivate(struct spi_slave *slave)
244 {
245 	struct sh_qspi_slave *ss = to_sh_qspi(slave);
246 
247 	sh_qspi_cs_deactivate(ss);
248 }
249 
250 struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
251 		unsigned int max_hz, unsigned int mode)
252 {
253 	struct sh_qspi_slave *ss;
254 
255 	if (!spi_cs_is_valid(bus, cs))
256 		return NULL;
257 
258 	ss = spi_alloc_slave(struct sh_qspi_slave, bus, cs);
259 	if (!ss) {
260 		printf("SPI_error: Fail to allocate sh_qspi_slave\n");
261 		return NULL;
262 	}
263 
264 	ss->regs = (struct sh_qspi_regs *)SH_QSPI_BASE;
265 
266 	/* Init SH QSPI */
267 	sh_qspi_init(ss);
268 
269 	return &ss->slave;
270 }
271 
272 void spi_free_slave(struct spi_slave *slave)
273 {
274 	struct sh_qspi_slave *spi = to_sh_qspi(slave);
275 
276 	free(spi);
277 }
278 
279 int spi_claim_bus(struct spi_slave *slave)
280 {
281 	return 0;
282 }
283 
284 void spi_release_bus(struct spi_slave *slave)
285 {
286 }
287 
288 int spi_xfer(struct spi_slave *slave, unsigned int bitlen,
289 	     const void *dout, void *din, unsigned long flags)
290 {
291 	struct sh_qspi_slave *ss = to_sh_qspi(slave);
292 
293 	return sh_qspi_xfer_common(ss, bitlen, dout, din, flags);
294 }
295 
296 #else
297 
298 #include <dm.h>
299 
300 static int sh_qspi_xfer(struct udevice *dev, unsigned int bitlen,
301 			const void *dout, void *din, unsigned long flags)
302 {
303 	struct udevice *bus = dev->parent;
304 	struct sh_qspi_slave *ss = dev_get_platdata(bus);
305 
306 	return sh_qspi_xfer_common(ss, bitlen, dout, din, flags);
307 }
308 
309 static int sh_qspi_set_speed(struct udevice *dev, uint speed)
310 {
311 	/* This is a SPI NOR controller, do nothing. */
312 	return 0;
313 }
314 
315 static int sh_qspi_set_mode(struct udevice *dev, uint mode)
316 {
317 	/* This is a SPI NOR controller, do nothing. */
318 	return 0;
319 }
320 
321 static int sh_qspi_probe(struct udevice *dev)
322 {
323 	struct sh_qspi_slave *ss = dev_get_platdata(dev);
324 
325 	sh_qspi_init(ss);
326 
327 	return 0;
328 }
329 
330 static int sh_qspi_ofdata_to_platdata(struct udevice *dev)
331 {
332 	struct sh_qspi_slave *plat = dev_get_platdata(dev);
333 
334 	plat->regs = (struct sh_qspi_regs *)dev_read_addr(dev);
335 
336 	return 0;
337 }
338 
339 static const struct dm_spi_ops sh_qspi_ops = {
340 	.xfer		= sh_qspi_xfer,
341 	.set_speed	= sh_qspi_set_speed,
342 	.set_mode	= sh_qspi_set_mode,
343 };
344 
345 static const struct udevice_id sh_qspi_ids[] = {
346 	{ .compatible = "renesas,qspi" },
347 	{ }
348 };
349 
350 U_BOOT_DRIVER(sh_qspi) = {
351 	.name		= "sh_qspi",
352 	.id		= UCLASS_SPI,
353 	.of_match	= sh_qspi_ids,
354 	.ops		= &sh_qspi_ops,
355 	.ofdata_to_platdata = sh_qspi_ofdata_to_platdata,
356 	.platdata_auto_alloc_size = sizeof(struct sh_qspi_slave),
357 	.probe		= sh_qspi_probe,
358 };
359 #endif
360