xref: /openbmc/u-boot/drivers/spi/rk_spi.c (revision d754254f)
1 /*
2  * spi driver for rockchip
3  *
4  * (C) Copyright 2015 Google, Inc
5  *
6  * (C) Copyright 2008-2013 Rockchip Electronics
7  * Peter, Software Engineering, <superpeter.cai@gmail.com>.
8  *
9  * SPDX-License-Identifier:     GPL-2.0+
10  */
11 
12 #include <common.h>
13 #include <clk.h>
14 #include <dm.h>
15 #include <dt-structs.h>
16 #include <errno.h>
17 #include <spi.h>
18 #include <linux/errno.h>
19 #include <asm/io.h>
20 #include <asm/arch/clock.h>
21 #include <asm/arch/periph.h>
22 #include <dm/pinctrl.h>
23 #include "rk_spi.h"
24 
25 DECLARE_GLOBAL_DATA_PTR;
26 
27 /* Change to 1 to output registers at the start of each transaction */
28 #define DEBUG_RK_SPI	0
29 
30 struct rockchip_spi_platdata {
31 #if CONFIG_IS_ENABLED(OF_PLATDATA)
32 	struct dtd_rockchip_rk3288_spi of_plat;
33 #endif
34 	s32 frequency;		/* Default clock frequency, -1 for none */
35 	fdt_addr_t base;
36 	uint deactivate_delay_us;	/* Delay to wait after deactivate */
37 	uint activate_delay_us;		/* Delay to wait after activate */
38 };
39 
40 struct rockchip_spi_priv {
41 	struct rockchip_spi *regs;
42 	struct clk clk;
43 	unsigned int max_freq;
44 	unsigned int mode;
45 	ulong last_transaction_us;	/* Time of last transaction end */
46 	u8 bits_per_word;		/* max 16 bits per word */
47 	u8 n_bytes;
48 	unsigned int speed_hz;
49 	unsigned int last_speed_hz;
50 	unsigned int tmode;
51 	uint input_rate;
52 };
53 
54 #define SPI_FIFO_DEPTH		32
55 
56 static void rkspi_dump_regs(struct rockchip_spi *regs)
57 {
58 	debug("ctrl0: \t\t0x%08x\n", readl(&regs->ctrlr0));
59 	debug("ctrl1: \t\t0x%08x\n", readl(&regs->ctrlr1));
60 	debug("ssienr: \t\t0x%08x\n", readl(&regs->enr));
61 	debug("ser: \t\t0x%08x\n", readl(&regs->ser));
62 	debug("baudr: \t\t0x%08x\n", readl(&regs->baudr));
63 	debug("txftlr: \t\t0x%08x\n", readl(&regs->txftlr));
64 	debug("rxftlr: \t\t0x%08x\n", readl(&regs->rxftlr));
65 	debug("txflr: \t\t0x%08x\n", readl(&regs->txflr));
66 	debug("rxflr: \t\t0x%08x\n", readl(&regs->rxflr));
67 	debug("sr: \t\t0x%08x\n", readl(&regs->sr));
68 	debug("imr: \t\t0x%08x\n", readl(&regs->imr));
69 	debug("isr: \t\t0x%08x\n", readl(&regs->isr));
70 	debug("dmacr: \t\t0x%08x\n", readl(&regs->dmacr));
71 	debug("dmatdlr: \t0x%08x\n", readl(&regs->dmatdlr));
72 	debug("dmardlr: \t0x%08x\n", readl(&regs->dmardlr));
73 }
74 
75 static void rkspi_enable_chip(struct rockchip_spi *regs, bool enable)
76 {
77 	writel(enable ? 1 : 0, &regs->enr);
78 }
79 
80 static void rkspi_set_clk(struct rockchip_spi_priv *priv, uint speed)
81 {
82 	/*
83 	 * We should try not to exceed the speed requested by the caller:
84 	 * when selecting a divider, we need to make sure we round up.
85 	 */
86 	uint clk_div = DIV_ROUND_UP(priv->input_rate, speed);
87 
88 	/* The baudrate register (BAUDR) is defined as a 32bit register where
89 	 * the upper 16bit are reserved and having 'Fsclk_out' in the lower
90 	 * 16bits with 'Fsclk_out' defined as follows:
91 	 *
92 	 *   Fsclk_out = Fspi_clk/ SCKDV
93 	 *   Where SCKDV is any even value between 2 and 65534.
94 	 */
95 	if (clk_div > 0xfffe) {
96 		clk_div = 0xfffe;
97 		debug("%s: can't divide down to %d hz (actual will be %d hz)\n",
98 		      __func__, speed, priv->input_rate / clk_div);
99 	}
100 
101 	/* Round up to the next even 16bit number */
102 	clk_div = (clk_div + 1) & 0xfffe;
103 
104 	debug("spi speed %u, div %u\n", speed, clk_div);
105 
106 	clrsetbits_le32(&priv->regs->baudr, 0xffff, clk_div);
107 	priv->last_speed_hz = speed;
108 }
109 
110 static int rkspi_wait_till_not_busy(struct rockchip_spi *regs)
111 {
112 	unsigned long start;
113 
114 	start = get_timer(0);
115 	while (readl(&regs->sr) & SR_BUSY) {
116 		if (get_timer(start) > ROCKCHIP_SPI_TIMEOUT_MS) {
117 			debug("RK SPI: Status keeps busy for 1000us after a read/write!\n");
118 			return -ETIMEDOUT;
119 		}
120 	}
121 
122 	return 0;
123 }
124 
125 static void spi_cs_activate(struct udevice *dev, uint cs)
126 {
127 	struct udevice *bus = dev->parent;
128 	struct rockchip_spi_platdata *plat = bus->platdata;
129 	struct rockchip_spi_priv *priv = dev_get_priv(bus);
130 	struct rockchip_spi *regs = priv->regs;
131 
132 	/* If it's too soon to do another transaction, wait */
133 	if (plat->deactivate_delay_us && priv->last_transaction_us) {
134 		ulong delay_us;		/* The delay completed so far */
135 		delay_us = timer_get_us() - priv->last_transaction_us;
136 		if (delay_us < plat->deactivate_delay_us)
137 			udelay(plat->deactivate_delay_us - delay_us);
138 	}
139 
140 	debug("activate cs%u\n", cs);
141 	writel(1 << cs, &regs->ser);
142 	if (plat->activate_delay_us)
143 		udelay(plat->activate_delay_us);
144 }
145 
146 static void spi_cs_deactivate(struct udevice *dev, uint cs)
147 {
148 	struct udevice *bus = dev->parent;
149 	struct rockchip_spi_platdata *plat = bus->platdata;
150 	struct rockchip_spi_priv *priv = dev_get_priv(bus);
151 	struct rockchip_spi *regs = priv->regs;
152 
153 	debug("deactivate cs%u\n", cs);
154 	writel(0, &regs->ser);
155 
156 	/* Remember time of this transaction so we can honour the bus delay */
157 	if (plat->deactivate_delay_us)
158 		priv->last_transaction_us = timer_get_us();
159 }
160 
161 #if CONFIG_IS_ENABLED(OF_PLATDATA)
162 static int conv_of_platdata(struct udevice *dev)
163 {
164 	struct rockchip_spi_platdata *plat = dev->platdata;
165 	struct dtd_rockchip_rk3288_spi *dtplat = &plat->of_plat;
166 	struct rockchip_spi_priv *priv = dev_get_priv(dev);
167 	int ret;
168 
169 	plat->base = dtplat->reg[0];
170 	plat->frequency = 20000000;
171 	ret = clk_get_by_index_platdata(dev, 0, dtplat->clocks, &priv->clk);
172 	if (ret < 0)
173 		return ret;
174 	dev->req_seq = 0;
175 
176 	return 0;
177 }
178 #endif
179 
180 static int rockchip_spi_ofdata_to_platdata(struct udevice *bus)
181 {
182 #if !CONFIG_IS_ENABLED(OF_PLATDATA)
183 	struct rockchip_spi_platdata *plat = dev_get_platdata(bus);
184 	struct rockchip_spi_priv *priv = dev_get_priv(bus);
185 	const void *blob = gd->fdt_blob;
186 	int node = dev_of_offset(bus);
187 	int ret;
188 
189 	plat->base = devfdt_get_addr(bus);
190 
191 	ret = clk_get_by_index(bus, 0, &priv->clk);
192 	if (ret < 0) {
193 		debug("%s: Could not get clock for %s: %d\n", __func__,
194 		      bus->name, ret);
195 		return ret;
196 	}
197 
198 	plat->frequency = fdtdec_get_int(blob, node, "spi-max-frequency",
199 					 50000000);
200 	plat->deactivate_delay_us = fdtdec_get_int(blob, node,
201 					"spi-deactivate-delay", 0);
202 	plat->activate_delay_us = fdtdec_get_int(blob, node,
203 						 "spi-activate-delay", 0);
204 	debug("%s: base=%x, max-frequency=%d, deactivate_delay=%d\n",
205 	      __func__, (uint)plat->base, plat->frequency,
206 	      plat->deactivate_delay_us);
207 #endif
208 
209 	return 0;
210 }
211 
212 static int rockchip_spi_calc_modclk(ulong max_freq)
213 {
214 	unsigned div;
215 	const unsigned long gpll_hz = 594000000UL;
216 
217 	/*
218 	 * We need to find an input clock that provides at least twice
219 	 * the maximum frequency and can be generated from the assumed
220 	 * speed of GPLL (594MHz) using an integer divider.
221 	 *
222 	 * To give us more achievable bitrates at higher speeds (these
223 	 * are generated by dividing by an even 16-bit integer from
224 	 * this frequency), we try to have an input frequency of at
225 	 * least 4x our max_freq.
226 	 */
227 
228 	div = DIV_ROUND_UP(gpll_hz, max_freq * 4);
229 	return gpll_hz / div;
230 }
231 
232 static int rockchip_spi_probe(struct udevice *bus)
233 {
234 	struct rockchip_spi_platdata *plat = dev_get_platdata(bus);
235 	struct rockchip_spi_priv *priv = dev_get_priv(bus);
236 	int ret;
237 
238 	debug("%s: probe\n", __func__);
239 #if CONFIG_IS_ENABLED(OF_PLATDATA)
240 	ret = conv_of_platdata(bus);
241 	if (ret)
242 		return ret;
243 #endif
244 	priv->regs = (struct rockchip_spi *)plat->base;
245 
246 	priv->last_transaction_us = timer_get_us();
247 	priv->max_freq = plat->frequency;
248 
249 	/* Clamp the value from the DTS against any hardware limits */
250 	if (priv->max_freq > ROCKCHIP_SPI_MAX_RATE)
251 		priv->max_freq = ROCKCHIP_SPI_MAX_RATE;
252 
253 	/* Find a module-input clock that fits with the max_freq setting */
254 	ret = clk_set_rate(&priv->clk,
255 			   rockchip_spi_calc_modclk(priv->max_freq));
256 	if (ret < 0) {
257 		debug("%s: Failed to set clock: %d\n", __func__, ret);
258 		return ret;
259 	}
260 	priv->input_rate = ret;
261 	debug("%s: rate = %u\n", __func__, priv->input_rate);
262 	priv->bits_per_word = 8;
263 	priv->tmode = TMOD_TR; /* Tx & Rx */
264 
265 	return 0;
266 }
267 
268 static int rockchip_spi_claim_bus(struct udevice *dev)
269 {
270 	struct udevice *bus = dev->parent;
271 	struct rockchip_spi_priv *priv = dev_get_priv(bus);
272 	struct rockchip_spi *regs = priv->regs;
273 	u8 spi_dfs, spi_tf;
274 	uint ctrlr0;
275 
276 	/* Disable the SPI hardware */
277 	rkspi_enable_chip(regs, 0);
278 
279 	switch (priv->bits_per_word) {
280 	case 8:
281 		priv->n_bytes = 1;
282 		spi_dfs = DFS_8BIT;
283 		spi_tf = HALF_WORD_OFF;
284 		break;
285 	case 16:
286 		priv->n_bytes = 2;
287 		spi_dfs = DFS_16BIT;
288 		spi_tf = HALF_WORD_ON;
289 		break;
290 	default:
291 		debug("%s: unsupported bits: %dbits\n", __func__,
292 		      priv->bits_per_word);
293 		return -EPROTONOSUPPORT;
294 	}
295 
296 	if (priv->speed_hz != priv->last_speed_hz)
297 		rkspi_set_clk(priv, priv->speed_hz);
298 
299 	/* Operation Mode */
300 	ctrlr0 = OMOD_MASTER << OMOD_SHIFT;
301 
302 	/* Data Frame Size */
303 	ctrlr0 |= spi_dfs << DFS_SHIFT;
304 
305 	/* set SPI mode 0..3 */
306 	if (priv->mode & SPI_CPOL)
307 		ctrlr0 |= SCOL_HIGH << SCOL_SHIFT;
308 	if (priv->mode & SPI_CPHA)
309 		ctrlr0 |= SCPH_TOGSTA << SCPH_SHIFT;
310 
311 	/* Chip Select Mode */
312 	ctrlr0 |= CSM_KEEP << CSM_SHIFT;
313 
314 	/* SSN to Sclk_out delay */
315 	ctrlr0 |= SSN_DELAY_ONE << SSN_DELAY_SHIFT;
316 
317 	/* Serial Endian Mode */
318 	ctrlr0 |= SEM_LITTLE << SEM_SHIFT;
319 
320 	/* First Bit Mode */
321 	ctrlr0 |= FBM_MSB << FBM_SHIFT;
322 
323 	/* Byte and Halfword Transform */
324 	ctrlr0 |= spi_tf << HALF_WORD_TX_SHIFT;
325 
326 	/* Rxd Sample Delay */
327 	ctrlr0 |= 0 << RXDSD_SHIFT;
328 
329 	/* Frame Format */
330 	ctrlr0 |= FRF_SPI << FRF_SHIFT;
331 
332 	/* Tx and Rx mode */
333 	ctrlr0 |= (priv->tmode & TMOD_MASK) << TMOD_SHIFT;
334 
335 	writel(ctrlr0, &regs->ctrlr0);
336 
337 	return 0;
338 }
339 
340 static int rockchip_spi_release_bus(struct udevice *dev)
341 {
342 	struct udevice *bus = dev->parent;
343 	struct rockchip_spi_priv *priv = dev_get_priv(bus);
344 
345 	rkspi_enable_chip(priv->regs, false);
346 
347 	return 0;
348 }
349 
350 static int rockchip_spi_xfer(struct udevice *dev, unsigned int bitlen,
351 			   const void *dout, void *din, unsigned long flags)
352 {
353 	struct udevice *bus = dev->parent;
354 	struct rockchip_spi_priv *priv = dev_get_priv(bus);
355 	struct rockchip_spi *regs = priv->regs;
356 	struct dm_spi_slave_platdata *slave_plat = dev_get_parent_platdata(dev);
357 	int len = bitlen >> 3;
358 	const u8 *out = dout;
359 	u8 *in = din;
360 	int toread, towrite;
361 	int ret;
362 
363 	debug("%s: dout=%p, din=%p, len=%x, flags=%lx\n", __func__, dout, din,
364 	      len, flags);
365 	if (DEBUG_RK_SPI)
366 		rkspi_dump_regs(regs);
367 
368 	/* Assert CS before transfer */
369 	if (flags & SPI_XFER_BEGIN)
370 		spi_cs_activate(dev, slave_plat->cs);
371 
372 	while (len > 0) {
373 		int todo = min(len, 0xffff);
374 
375 		rkspi_enable_chip(regs, false);
376 		writel(todo - 1, &regs->ctrlr1);
377 		rkspi_enable_chip(regs, true);
378 
379 		toread = todo;
380 		towrite = todo;
381 		while (toread || towrite) {
382 			u32 status = readl(&regs->sr);
383 
384 			if (towrite && !(status & SR_TF_FULL)) {
385 				writel(out ? *out++ : 0, regs->txdr);
386 				towrite--;
387 			}
388 			if (toread && !(status & SR_RF_EMPT)) {
389 				u32 byte = readl(regs->rxdr);
390 
391 				if (in)
392 					*in++ = byte;
393 				toread--;
394 			}
395 		}
396 		ret = rkspi_wait_till_not_busy(regs);
397 		if (ret)
398 			break;
399 		len -= todo;
400 	}
401 
402 	/* Deassert CS after transfer */
403 	if (flags & SPI_XFER_END)
404 		spi_cs_deactivate(dev, slave_plat->cs);
405 
406 	rkspi_enable_chip(regs, false);
407 
408 	return ret;
409 }
410 
411 static int rockchip_spi_set_speed(struct udevice *bus, uint speed)
412 {
413 	struct rockchip_spi_priv *priv = dev_get_priv(bus);
414 
415 	/* Clamp to the maximum frequency specified in the DTS */
416 	if (speed > priv->max_freq)
417 		speed = priv->max_freq;
418 
419 	priv->speed_hz = speed;
420 
421 	return 0;
422 }
423 
424 static int rockchip_spi_set_mode(struct udevice *bus, uint mode)
425 {
426 	struct rockchip_spi_priv *priv = dev_get_priv(bus);
427 
428 	priv->mode = mode;
429 
430 	return 0;
431 }
432 
433 static const struct dm_spi_ops rockchip_spi_ops = {
434 	.claim_bus	= rockchip_spi_claim_bus,
435 	.release_bus	= rockchip_spi_release_bus,
436 	.xfer		= rockchip_spi_xfer,
437 	.set_speed	= rockchip_spi_set_speed,
438 	.set_mode	= rockchip_spi_set_mode,
439 	/*
440 	 * cs_info is not needed, since we require all chip selects to be
441 	 * in the device tree explicitly
442 	 */
443 };
444 
445 static const struct udevice_id rockchip_spi_ids[] = {
446 	{ .compatible = "rockchip,rk3288-spi" },
447 	{ .compatible = "rockchip,rk3399-spi" },
448 	{ }
449 };
450 
451 U_BOOT_DRIVER(rockchip_spi) = {
452 #if CONFIG_IS_ENABLED(OF_PLATDATA)
453 	.name	= "rockchip_rk3288_spi",
454 #else
455 	.name	= "rockchip_spi",
456 #endif
457 	.id	= UCLASS_SPI,
458 	.of_match = rockchip_spi_ids,
459 	.ops	= &rockchip_spi_ops,
460 	.ofdata_to_platdata = rockchip_spi_ofdata_to_platdata,
461 	.platdata_auto_alloc_size = sizeof(struct rockchip_spi_platdata),
462 	.priv_auto_alloc_size = sizeof(struct rockchip_spi_priv),
463 	.probe	= rockchip_spi_probe,
464 };
465