xref: /openbmc/u-boot/drivers/spi/mxs_spi.c (revision 71a988aa)
1 /*
2  * Freescale i.MX28 SPI driver
3  *
4  * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
5  * on behalf of DENX Software Engineering GmbH
6  *
7  * This program is free software; you can redistribute it and/or
8  * modify it under the terms of the GNU General Public License as
9  * published by the Free Software Foundation; either version 2 of
10  * the License, or (at your option) any later version.
11  *
12  * This program is distributed in the hope that it will be useful,
13  * but WITHOUT ANY WARRANTY; without even the implied warranty of
14  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
15  * GNU General Public License for more details.
16  *
17  * You should have received a copy of the GNU General Public License
18  * along with this program; if not, write to the Free Software
19  * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
20  * MA 02111-1307 USA
21  *
22  * NOTE: This driver only supports the SPI-controller chipselects,
23  *       GPIO driven chipselects are not supported.
24  */
25 
26 #include <common.h>
27 #include <malloc.h>
28 #include <spi.h>
29 #include <asm/errno.h>
30 #include <asm/io.h>
31 #include <asm/arch/clock.h>
32 #include <asm/arch/imx-regs.h>
33 #include <asm/arch/sys_proto.h>
34 #include <asm/arch/dma.h>
35 
36 #define	MXS_SPI_MAX_TIMEOUT	1000000
37 #define	MXS_SPI_PORT_OFFSET	0x2000
38 #define MXS_SSP_CHIPSELECT_MASK		0x00300000
39 #define MXS_SSP_CHIPSELECT_SHIFT	20
40 
41 #define MXSSSP_SMALL_TRANSFER	512
42 
43 /*
44  * CONFIG_MXS_SPI_DMA_ENABLE: Experimental mixed PIO/DMA support for MXS SPI
45  *                            host. Use with utmost caution!
46  *
47  *                            Enabling this is not yet recommended since this
48  *                            still doesn't support transfers to/from unaligned
49  *                            addresses. Therefore this driver will not work
50  *                            for example with saving environment. This is
51  *                            caused by DMA alignment constraints on MXS.
52  */
53 
54 struct mxs_spi_slave {
55 	struct spi_slave	slave;
56 	uint32_t		max_khz;
57 	uint32_t		mode;
58 	struct mxs_ssp_regs	*regs;
59 };
60 
61 static inline struct mxs_spi_slave *to_mxs_slave(struct spi_slave *slave)
62 {
63 	return container_of(slave, struct mxs_spi_slave, slave);
64 }
65 
66 void spi_init(void)
67 {
68 }
69 
70 int spi_cs_is_valid(unsigned int bus, unsigned int cs)
71 {
72 	/* MXS SPI: 4 ports and 3 chip selects maximum */
73 	if (bus > 3 || cs > 2)
74 		return 0;
75 	else
76 		return 1;
77 }
78 
79 struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
80 				  unsigned int max_hz, unsigned int mode)
81 {
82 	struct mxs_spi_slave *mxs_slave;
83 	struct mxs_ssp_regs *ssp_regs;
84 	int reg;
85 
86 	if (!spi_cs_is_valid(bus, cs)) {
87 		printf("mxs_spi: invalid bus %d / chip select %d\n", bus, cs);
88 		return NULL;
89 	}
90 
91 	mxs_slave = calloc(sizeof(struct mxs_spi_slave), 1);
92 	if (!mxs_slave)
93 		return NULL;
94 
95 	if (mxs_dma_init_channel(bus))
96 		goto err_init;
97 
98 	mxs_slave->slave.bus = bus;
99 	mxs_slave->slave.cs = cs;
100 	mxs_slave->max_khz = max_hz / 1000;
101 	mxs_slave->mode = mode;
102 	mxs_slave->regs = mxs_ssp_regs_by_bus(bus);
103 	ssp_regs = mxs_slave->regs;
104 
105 	reg = readl(&ssp_regs->hw_ssp_ctrl0);
106 	reg &= ~(MXS_SSP_CHIPSELECT_MASK);
107 	reg |= cs << MXS_SSP_CHIPSELECT_SHIFT;
108 
109 	writel(reg, &ssp_regs->hw_ssp_ctrl0);
110 	return &mxs_slave->slave;
111 
112 err_init:
113 	free(mxs_slave);
114 	return NULL;
115 }
116 
117 void spi_free_slave(struct spi_slave *slave)
118 {
119 	struct mxs_spi_slave *mxs_slave = to_mxs_slave(slave);
120 	free(mxs_slave);
121 }
122 
123 int spi_claim_bus(struct spi_slave *slave)
124 {
125 	struct mxs_spi_slave *mxs_slave = to_mxs_slave(slave);
126 	struct mxs_ssp_regs *ssp_regs = mxs_slave->regs;
127 	uint32_t reg = 0;
128 
129 	mxs_reset_block(&ssp_regs->hw_ssp_ctrl0_reg);
130 
131 	writel(SSP_CTRL0_BUS_WIDTH_ONE_BIT, &ssp_regs->hw_ssp_ctrl0);
132 
133 	reg = SSP_CTRL1_SSP_MODE_SPI | SSP_CTRL1_WORD_LENGTH_EIGHT_BITS;
134 	reg |= (mxs_slave->mode & SPI_CPOL) ? SSP_CTRL1_POLARITY : 0;
135 	reg |= (mxs_slave->mode & SPI_CPHA) ? SSP_CTRL1_PHASE : 0;
136 	writel(reg, &ssp_regs->hw_ssp_ctrl1);
137 
138 	writel(0, &ssp_regs->hw_ssp_cmd0);
139 
140 	mxs_set_ssp_busclock(slave->bus, mxs_slave->max_khz);
141 
142 	return 0;
143 }
144 
145 void spi_release_bus(struct spi_slave *slave)
146 {
147 }
148 
149 static void mxs_spi_start_xfer(struct mxs_ssp_regs *ssp_regs)
150 {
151 	writel(SSP_CTRL0_LOCK_CS, &ssp_regs->hw_ssp_ctrl0_set);
152 	writel(SSP_CTRL0_IGNORE_CRC, &ssp_regs->hw_ssp_ctrl0_clr);
153 }
154 
155 static void mxs_spi_end_xfer(struct mxs_ssp_regs *ssp_regs)
156 {
157 	writel(SSP_CTRL0_LOCK_CS, &ssp_regs->hw_ssp_ctrl0_clr);
158 	writel(SSP_CTRL0_IGNORE_CRC, &ssp_regs->hw_ssp_ctrl0_set);
159 }
160 
161 static int mxs_spi_xfer_pio(struct mxs_spi_slave *slave,
162 			char *data, int length, int write, unsigned long flags)
163 {
164 	struct mxs_ssp_regs *ssp_regs = slave->regs;
165 
166 	if (flags & SPI_XFER_BEGIN)
167 		mxs_spi_start_xfer(ssp_regs);
168 
169 	while (length--) {
170 		/* We transfer 1 byte */
171 		writel(1, &ssp_regs->hw_ssp_xfer_size);
172 
173 		if ((flags & SPI_XFER_END) && !length)
174 			mxs_spi_end_xfer(ssp_regs);
175 
176 		if (write)
177 			writel(SSP_CTRL0_READ, &ssp_regs->hw_ssp_ctrl0_clr);
178 		else
179 			writel(SSP_CTRL0_READ, &ssp_regs->hw_ssp_ctrl0_set);
180 
181 		writel(SSP_CTRL0_RUN, &ssp_regs->hw_ssp_ctrl0_set);
182 
183 		if (mxs_wait_mask_set(&ssp_regs->hw_ssp_ctrl0_reg,
184 			SSP_CTRL0_RUN, MXS_SPI_MAX_TIMEOUT)) {
185 			printf("MXS SPI: Timeout waiting for start\n");
186 			return -ETIMEDOUT;
187 		}
188 
189 		if (write)
190 			writel(*data++, &ssp_regs->hw_ssp_data);
191 
192 		writel(SSP_CTRL0_DATA_XFER, &ssp_regs->hw_ssp_ctrl0_set);
193 
194 		if (!write) {
195 			if (mxs_wait_mask_clr(&ssp_regs->hw_ssp_status_reg,
196 				SSP_STATUS_FIFO_EMPTY, MXS_SPI_MAX_TIMEOUT)) {
197 				printf("MXS SPI: Timeout waiting for data\n");
198 				return -ETIMEDOUT;
199 			}
200 
201 			*data = readl(&ssp_regs->hw_ssp_data);
202 			data++;
203 		}
204 
205 		if (mxs_wait_mask_clr(&ssp_regs->hw_ssp_ctrl0_reg,
206 			SSP_CTRL0_RUN, MXS_SPI_MAX_TIMEOUT)) {
207 			printf("MXS SPI: Timeout waiting for finish\n");
208 			return -ETIMEDOUT;
209 		}
210 	}
211 
212 	return 0;
213 }
214 
215 static int mxs_spi_xfer_dma(struct mxs_spi_slave *slave,
216 			char *data, int length, int write, unsigned long flags)
217 {
218 	const int xfer_max_sz = 0xff00;
219 	const int desc_count = DIV_ROUND_UP(length, xfer_max_sz) + 1;
220 	struct mxs_ssp_regs *ssp_regs = slave->regs;
221 	struct mxs_dma_desc *dp;
222 	uint32_t ctrl0;
223 	uint32_t cache_data_count;
224 	const uint32_t dstart = (uint32_t)data;
225 	int dmach;
226 	int tl;
227 	int ret = 0;
228 
229 	ALLOC_CACHE_ALIGN_BUFFER(struct mxs_dma_desc, desc, desc_count);
230 
231 	memset(desc, 0, sizeof(struct mxs_dma_desc) * desc_count);
232 
233 	ctrl0 = readl(&ssp_regs->hw_ssp_ctrl0);
234 	ctrl0 |= SSP_CTRL0_DATA_XFER;
235 
236 	if (flags & SPI_XFER_BEGIN)
237 		ctrl0 |= SSP_CTRL0_LOCK_CS;
238 	if (!write)
239 		ctrl0 |= SSP_CTRL0_READ;
240 
241 	if (length % ARCH_DMA_MINALIGN)
242 		cache_data_count = roundup(length, ARCH_DMA_MINALIGN);
243 	else
244 		cache_data_count = length;
245 
246 	/* Flush data to DRAM so DMA can pick them up */
247 	if (write)
248 		flush_dcache_range(dstart, dstart + cache_data_count);
249 
250 	/* Invalidate the area, so no writeback into the RAM races with DMA */
251 	invalidate_dcache_range(dstart, dstart + cache_data_count);
252 
253 	dmach = MXS_DMA_CHANNEL_AHB_APBH_SSP0 + slave->slave.bus;
254 
255 	dp = desc;
256 	while (length) {
257 		dp->address = (dma_addr_t)dp;
258 		dp->cmd.address = (dma_addr_t)data;
259 
260 		/*
261 		 * This is correct, even though it does indeed look insane.
262 		 * I hereby have to, wholeheartedly, thank Freescale Inc.,
263 		 * for always inventing insane hardware and keeping me busy
264 		 * and employed ;-)
265 		 */
266 		if (write)
267 			dp->cmd.data = MXS_DMA_DESC_COMMAND_DMA_READ;
268 		else
269 			dp->cmd.data = MXS_DMA_DESC_COMMAND_DMA_WRITE;
270 
271 		/*
272 		 * The DMA controller can transfer large chunks (64kB) at
273 		 * time by setting the transfer length to 0. Setting tl to
274 		 * 0x10000 will overflow below and make .data contain 0.
275 		 * Otherwise, 0xff00 is the transfer maximum.
276 		 */
277 		if (length >= 0x10000)
278 			tl = 0x10000;
279 		else
280 			tl = min(length, xfer_max_sz);
281 
282 		dp->cmd.data |=
283 			((tl & 0xffff) << MXS_DMA_DESC_BYTES_OFFSET) |
284 			(4 << MXS_DMA_DESC_PIO_WORDS_OFFSET) |
285 			MXS_DMA_DESC_HALT_ON_TERMINATE |
286 			MXS_DMA_DESC_TERMINATE_FLUSH;
287 
288 		data += tl;
289 		length -= tl;
290 
291 		if (!length) {
292 			dp->cmd.data |= MXS_DMA_DESC_IRQ | MXS_DMA_DESC_DEC_SEM;
293 
294 			if (flags & SPI_XFER_END) {
295 				ctrl0 &= ~SSP_CTRL0_LOCK_CS;
296 				ctrl0 |= SSP_CTRL0_IGNORE_CRC;
297 			}
298 		}
299 
300 		/*
301 		 * Write CTRL0, CMD0, CMD1, XFER_SIZE registers. It is
302 		 * essential that the XFER_SIZE register is written on
303 		 * a per-descriptor basis with the same size as is the
304 		 * descriptor!
305 		 */
306 		dp->cmd.pio_words[0] = ctrl0;
307 		dp->cmd.pio_words[1] = 0;
308 		dp->cmd.pio_words[2] = 0;
309 		dp->cmd.pio_words[3] = tl;
310 
311 		mxs_dma_desc_append(dmach, dp);
312 
313 		dp++;
314 	}
315 
316 	if (mxs_dma_go(dmach))
317 		ret = -EINVAL;
318 
319 	/* The data arrived into DRAM, invalidate cache over them */
320 	if (!write)
321 		invalidate_dcache_range(dstart, dstart + cache_data_count);
322 
323 	return ret;
324 }
325 
326 int spi_xfer(struct spi_slave *slave, unsigned int bitlen,
327 		const void *dout, void *din, unsigned long flags)
328 {
329 	struct mxs_spi_slave *mxs_slave = to_mxs_slave(slave);
330 	struct mxs_ssp_regs *ssp_regs = mxs_slave->regs;
331 	int len = bitlen / 8;
332 	char dummy;
333 	int write = 0;
334 	char *data = NULL;
335 
336 #ifdef CONFIG_MXS_SPI_DMA_ENABLE
337 	int dma = 1;
338 #else
339 	int dma = 0;
340 #endif
341 
342 	if (bitlen == 0) {
343 		if (flags & SPI_XFER_END) {
344 			din = (void *)&dummy;
345 			len = 1;
346 		} else
347 			return 0;
348 	}
349 
350 	/* Half-duplex only */
351 	if (din && dout)
352 		return -EINVAL;
353 	/* No data */
354 	if (!din && !dout)
355 		return 0;
356 
357 	if (dout) {
358 		data = (char *)dout;
359 		write = 1;
360 	} else if (din) {
361 		data = (char *)din;
362 		write = 0;
363 	}
364 
365 	/*
366 	 * Check for alignment, if the buffer is aligned, do DMA transfer,
367 	 * PIO otherwise. This is a temporary workaround until proper bounce
368 	 * buffer is in place.
369 	 */
370 	if (dma) {
371 		if (((uint32_t)data) & (ARCH_DMA_MINALIGN - 1))
372 			dma = 0;
373 		if (((uint32_t)len) & (ARCH_DMA_MINALIGN - 1))
374 			dma = 0;
375 	}
376 
377 	if (!dma || (len < MXSSSP_SMALL_TRANSFER)) {
378 		writel(SSP_CTRL1_DMA_ENABLE, &ssp_regs->hw_ssp_ctrl1_clr);
379 		return mxs_spi_xfer_pio(mxs_slave, data, len, write, flags);
380 	} else {
381 		writel(SSP_CTRL1_DMA_ENABLE, &ssp_regs->hw_ssp_ctrl1_set);
382 		return mxs_spi_xfer_dma(mxs_slave, data, len, write, flags);
383 	}
384 }
385