1 /* 2 * Copyright (C) 2008, Guennadi Liakhovetski <lg@denx.de> 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #include <common.h> 8 #include <malloc.h> 9 #include <spi.h> 10 #include <linux/errno.h> 11 #include <asm/io.h> 12 #include <asm/gpio.h> 13 #include <asm/arch/imx-regs.h> 14 #include <asm/arch/clock.h> 15 #include <asm/mach-imx/spi.h> 16 17 #ifdef CONFIG_MX27 18 /* i.MX27 has a completely wrong register layout and register definitions in the 19 * datasheet, the correct one is in the Freescale's Linux driver */ 20 21 #error "i.MX27 CSPI not supported due to drastic differences in register definitions" \ 22 "See linux mxc_spi driver from Freescale for details." 23 #endif 24 25 static unsigned long spi_bases[] = { 26 MXC_SPI_BASE_ADDRESSES 27 }; 28 29 __weak int board_spi_cs_gpio(unsigned bus, unsigned cs) 30 { 31 return -1; 32 } 33 34 #define OUT MXC_GPIO_DIRECTION_OUT 35 36 #define reg_read readl 37 #define reg_write(a, v) writel(v, a) 38 39 #if !defined(CONFIG_SYS_SPI_MXC_WAIT) 40 #define CONFIG_SYS_SPI_MXC_WAIT (CONFIG_SYS_HZ/100) /* 10 ms */ 41 #endif 42 43 struct mxc_spi_slave { 44 struct spi_slave slave; 45 unsigned long base; 46 u32 ctrl_reg; 47 #if defined(MXC_ECSPI) 48 u32 cfg_reg; 49 #endif 50 int gpio; 51 int ss_pol; 52 unsigned int max_hz; 53 unsigned int mode; 54 }; 55 56 static inline struct mxc_spi_slave *to_mxc_spi_slave(struct spi_slave *slave) 57 { 58 return container_of(slave, struct mxc_spi_slave, slave); 59 } 60 61 void spi_cs_activate(struct spi_slave *slave) 62 { 63 struct mxc_spi_slave *mxcs = to_mxc_spi_slave(slave); 64 if (mxcs->gpio > 0) 65 gpio_set_value(mxcs->gpio, mxcs->ss_pol); 66 } 67 68 void spi_cs_deactivate(struct spi_slave *slave) 69 { 70 struct mxc_spi_slave *mxcs = to_mxc_spi_slave(slave); 71 if (mxcs->gpio > 0) 72 gpio_set_value(mxcs->gpio, 73 !(mxcs->ss_pol)); 74 } 75 76 u32 get_cspi_div(u32 div) 77 { 78 int i; 79 80 for (i = 0; i < 8; i++) { 81 if (div <= (4 << i)) 82 return i; 83 } 84 return i; 85 } 86 87 #ifdef MXC_CSPI 88 static s32 spi_cfg_mxc(struct mxc_spi_slave *mxcs, unsigned int cs) 89 { 90 unsigned int ctrl_reg; 91 u32 clk_src; 92 u32 div; 93 unsigned int max_hz = mxcs->max_hz; 94 unsigned int mode = mxcs->mode; 95 96 clk_src = mxc_get_clock(MXC_CSPI_CLK); 97 98 div = DIV_ROUND_UP(clk_src, max_hz); 99 div = get_cspi_div(div); 100 101 debug("clk %d Hz, div %d, real clk %d Hz\n", 102 max_hz, div, clk_src / (4 << div)); 103 104 ctrl_reg = MXC_CSPICTRL_CHIPSELECT(cs) | 105 MXC_CSPICTRL_BITCOUNT(MXC_CSPICTRL_MAXBITS) | 106 MXC_CSPICTRL_DATARATE(div) | 107 MXC_CSPICTRL_EN | 108 #ifdef CONFIG_MX35 109 MXC_CSPICTRL_SSCTL | 110 #endif 111 MXC_CSPICTRL_MODE; 112 113 if (mode & SPI_CPHA) 114 ctrl_reg |= MXC_CSPICTRL_PHA; 115 if (mode & SPI_CPOL) 116 ctrl_reg |= MXC_CSPICTRL_POL; 117 if (mode & SPI_CS_HIGH) 118 ctrl_reg |= MXC_CSPICTRL_SSPOL; 119 mxcs->ctrl_reg = ctrl_reg; 120 121 return 0; 122 } 123 #endif 124 125 #ifdef MXC_ECSPI 126 static s32 spi_cfg_mxc(struct mxc_spi_slave *mxcs, unsigned int cs) 127 { 128 u32 clk_src = mxc_get_clock(MXC_CSPI_CLK); 129 s32 reg_ctrl, reg_config; 130 u32 ss_pol = 0, sclkpol = 0, sclkpha = 0, sclkctl = 0; 131 u32 pre_div = 0, post_div = 0; 132 struct cspi_regs *regs = (struct cspi_regs *)mxcs->base; 133 unsigned int max_hz = mxcs->max_hz; 134 unsigned int mode = mxcs->mode; 135 136 /* 137 * Reset SPI and set all CSs to master mode, if toggling 138 * between slave and master mode we might see a glitch 139 * on the clock line 140 */ 141 reg_ctrl = MXC_CSPICTRL_MODE_MASK; 142 reg_write(®s->ctrl, reg_ctrl); 143 reg_ctrl |= MXC_CSPICTRL_EN; 144 reg_write(®s->ctrl, reg_ctrl); 145 146 if (clk_src > max_hz) { 147 pre_div = (clk_src - 1) / max_hz; 148 /* fls(1) = 1, fls(0x80000000) = 32, fls(16) = 5 */ 149 post_div = fls(pre_div); 150 if (post_div > 4) { 151 post_div -= 4; 152 if (post_div >= 16) { 153 printf("Error: no divider for the freq: %d\n", 154 max_hz); 155 return -1; 156 } 157 pre_div >>= post_div; 158 } else { 159 post_div = 0; 160 } 161 } 162 163 debug("pre_div = %d, post_div=%d\n", pre_div, post_div); 164 reg_ctrl = (reg_ctrl & ~MXC_CSPICTRL_SELCHAN(3)) | 165 MXC_CSPICTRL_SELCHAN(cs); 166 reg_ctrl = (reg_ctrl & ~MXC_CSPICTRL_PREDIV(0x0F)) | 167 MXC_CSPICTRL_PREDIV(pre_div); 168 reg_ctrl = (reg_ctrl & ~MXC_CSPICTRL_POSTDIV(0x0F)) | 169 MXC_CSPICTRL_POSTDIV(post_div); 170 171 if (mode & SPI_CS_HIGH) 172 ss_pol = 1; 173 174 if (mode & SPI_CPOL) { 175 sclkpol = 1; 176 sclkctl = 1; 177 } 178 179 if (mode & SPI_CPHA) 180 sclkpha = 1; 181 182 reg_config = reg_read(®s->cfg); 183 184 /* 185 * Configuration register setup 186 * The MX51 supports different setup for each SS 187 */ 188 reg_config = (reg_config & ~(1 << (cs + MXC_CSPICON_SSPOL))) | 189 (ss_pol << (cs + MXC_CSPICON_SSPOL)); 190 reg_config = (reg_config & ~(1 << (cs + MXC_CSPICON_POL))) | 191 (sclkpol << (cs + MXC_CSPICON_POL)); 192 reg_config = (reg_config & ~(1 << (cs + MXC_CSPICON_CTL))) | 193 (sclkctl << (cs + MXC_CSPICON_CTL)); 194 reg_config = (reg_config & ~(1 << (cs + MXC_CSPICON_PHA))) | 195 (sclkpha << (cs + MXC_CSPICON_PHA)); 196 197 debug("reg_ctrl = 0x%x\n", reg_ctrl); 198 reg_write(®s->ctrl, reg_ctrl); 199 debug("reg_config = 0x%x\n", reg_config); 200 reg_write(®s->cfg, reg_config); 201 202 /* save config register and control register */ 203 mxcs->ctrl_reg = reg_ctrl; 204 mxcs->cfg_reg = reg_config; 205 206 /* clear interrupt reg */ 207 reg_write(®s->intr, 0); 208 reg_write(®s->stat, MXC_CSPICTRL_TC | MXC_CSPICTRL_RXOVF); 209 210 return 0; 211 } 212 #endif 213 214 int spi_xchg_single(struct spi_slave *slave, unsigned int bitlen, 215 const u8 *dout, u8 *din, unsigned long flags) 216 { 217 struct mxc_spi_slave *mxcs = to_mxc_spi_slave(slave); 218 int nbytes = DIV_ROUND_UP(bitlen, 8); 219 u32 data, cnt, i; 220 struct cspi_regs *regs = (struct cspi_regs *)mxcs->base; 221 u32 ts; 222 int status; 223 224 debug("%s: bitlen %d dout 0x%x din 0x%x\n", 225 __func__, bitlen, (u32)dout, (u32)din); 226 227 mxcs->ctrl_reg = (mxcs->ctrl_reg & 228 ~MXC_CSPICTRL_BITCOUNT(MXC_CSPICTRL_MAXBITS)) | 229 MXC_CSPICTRL_BITCOUNT(bitlen - 1); 230 231 reg_write(®s->ctrl, mxcs->ctrl_reg | MXC_CSPICTRL_EN); 232 #ifdef MXC_ECSPI 233 reg_write(®s->cfg, mxcs->cfg_reg); 234 #endif 235 236 /* Clear interrupt register */ 237 reg_write(®s->stat, MXC_CSPICTRL_TC | MXC_CSPICTRL_RXOVF); 238 239 /* 240 * The SPI controller works only with words, 241 * check if less than a word is sent. 242 * Access to the FIFO is only 32 bit 243 */ 244 if (bitlen % 32) { 245 data = 0; 246 cnt = (bitlen % 32) / 8; 247 if (dout) { 248 for (i = 0; i < cnt; i++) { 249 data = (data << 8) | (*dout++ & 0xFF); 250 } 251 } 252 debug("Sending SPI 0x%x\n", data); 253 254 reg_write(®s->txdata, data); 255 nbytes -= cnt; 256 } 257 258 data = 0; 259 260 while (nbytes > 0) { 261 data = 0; 262 if (dout) { 263 /* Buffer is not 32-bit aligned */ 264 if ((unsigned long)dout & 0x03) { 265 data = 0; 266 for (i = 0; i < 4; i++) 267 data = (data << 8) | (*dout++ & 0xFF); 268 } else { 269 data = *(u32 *)dout; 270 data = cpu_to_be32(data); 271 dout += 4; 272 } 273 } 274 debug("Sending SPI 0x%x\n", data); 275 reg_write(®s->txdata, data); 276 nbytes -= 4; 277 } 278 279 /* FIFO is written, now starts the transfer setting the XCH bit */ 280 reg_write(®s->ctrl, mxcs->ctrl_reg | 281 MXC_CSPICTRL_EN | MXC_CSPICTRL_XCH); 282 283 ts = get_timer(0); 284 status = reg_read(®s->stat); 285 /* Wait until the TC (Transfer completed) bit is set */ 286 while ((status & MXC_CSPICTRL_TC) == 0) { 287 if (get_timer(ts) > CONFIG_SYS_SPI_MXC_WAIT) { 288 printf("spi_xchg_single: Timeout!\n"); 289 return -1; 290 } 291 status = reg_read(®s->stat); 292 } 293 294 /* Transfer completed, clear any pending request */ 295 reg_write(®s->stat, MXC_CSPICTRL_TC | MXC_CSPICTRL_RXOVF); 296 297 nbytes = DIV_ROUND_UP(bitlen, 8); 298 299 cnt = nbytes % 32; 300 301 if (bitlen % 32) { 302 data = reg_read(®s->rxdata); 303 cnt = (bitlen % 32) / 8; 304 data = cpu_to_be32(data) >> ((sizeof(data) - cnt) * 8); 305 debug("SPI Rx unaligned: 0x%x\n", data); 306 if (din) { 307 memcpy(din, &data, cnt); 308 din += cnt; 309 } 310 nbytes -= cnt; 311 } 312 313 while (nbytes > 0) { 314 u32 tmp; 315 tmp = reg_read(®s->rxdata); 316 data = cpu_to_be32(tmp); 317 debug("SPI Rx: 0x%x 0x%x\n", tmp, data); 318 cnt = min_t(u32, nbytes, sizeof(data)); 319 if (din) { 320 memcpy(din, &data, cnt); 321 din += cnt; 322 } 323 nbytes -= cnt; 324 } 325 326 return 0; 327 328 } 329 330 int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *dout, 331 void *din, unsigned long flags) 332 { 333 int n_bytes = DIV_ROUND_UP(bitlen, 8); 334 int n_bits; 335 int ret; 336 u32 blk_size; 337 u8 *p_outbuf = (u8 *)dout; 338 u8 *p_inbuf = (u8 *)din; 339 340 if (!slave) 341 return -1; 342 343 if (flags & SPI_XFER_BEGIN) 344 spi_cs_activate(slave); 345 346 while (n_bytes > 0) { 347 if (n_bytes < MAX_SPI_BYTES) 348 blk_size = n_bytes; 349 else 350 blk_size = MAX_SPI_BYTES; 351 352 n_bits = blk_size * 8; 353 354 ret = spi_xchg_single(slave, n_bits, p_outbuf, p_inbuf, 0); 355 356 if (ret) 357 return ret; 358 if (dout) 359 p_outbuf += blk_size; 360 if (din) 361 p_inbuf += blk_size; 362 n_bytes -= blk_size; 363 } 364 365 if (flags & SPI_XFER_END) { 366 spi_cs_deactivate(slave); 367 } 368 369 return 0; 370 } 371 372 void spi_init(void) 373 { 374 } 375 376 /* 377 * Some SPI devices require active chip-select over multiple 378 * transactions, we achieve this using a GPIO. Still, the SPI 379 * controller has to be configured to use one of its own chipselects. 380 * To use this feature you have to implement board_spi_cs_gpio() to assign 381 * a gpio value for each cs (-1 if cs doesn't need to use gpio). 382 * You must use some unused on this SPI controller cs between 0 and 3. 383 */ 384 static int setup_cs_gpio(struct mxc_spi_slave *mxcs, 385 unsigned int bus, unsigned int cs) 386 { 387 int ret; 388 389 mxcs->gpio = board_spi_cs_gpio(bus, cs); 390 if (mxcs->gpio == -1) 391 return 0; 392 393 ret = gpio_direction_output(mxcs->gpio, !(mxcs->ss_pol)); 394 if (ret) { 395 printf("mxc_spi: cannot setup gpio %d\n", mxcs->gpio); 396 return -EINVAL; 397 } 398 399 return 0; 400 } 401 402 struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs, 403 unsigned int max_hz, unsigned int mode) 404 { 405 struct mxc_spi_slave *mxcs; 406 int ret; 407 408 if (bus >= ARRAY_SIZE(spi_bases)) 409 return NULL; 410 411 if (max_hz == 0) { 412 printf("Error: desired clock is 0\n"); 413 return NULL; 414 } 415 416 mxcs = spi_alloc_slave(struct mxc_spi_slave, bus, cs); 417 if (!mxcs) { 418 puts("mxc_spi: SPI Slave not allocated !\n"); 419 return NULL; 420 } 421 422 mxcs->ss_pol = (mode & SPI_CS_HIGH) ? 1 : 0; 423 424 ret = setup_cs_gpio(mxcs, bus, cs); 425 if (ret < 0) { 426 free(mxcs); 427 return NULL; 428 } 429 430 mxcs->base = spi_bases[bus]; 431 mxcs->max_hz = max_hz; 432 mxcs->mode = mode; 433 434 return &mxcs->slave; 435 } 436 437 void spi_free_slave(struct spi_slave *slave) 438 { 439 struct mxc_spi_slave *mxcs = to_mxc_spi_slave(slave); 440 441 free(mxcs); 442 } 443 444 int spi_claim_bus(struct spi_slave *slave) 445 { 446 int ret; 447 struct mxc_spi_slave *mxcs = to_mxc_spi_slave(slave); 448 struct cspi_regs *regs = (struct cspi_regs *)mxcs->base; 449 450 reg_write(®s->rxdata, 1); 451 udelay(1); 452 ret = spi_cfg_mxc(mxcs, slave->cs); 453 if (ret) { 454 printf("mxc_spi: cannot setup SPI controller\n"); 455 return ret; 456 } 457 reg_write(®s->period, MXC_CSPIPERIOD_32KHZ); 458 reg_write(®s->intr, 0); 459 460 return 0; 461 } 462 463 void spi_release_bus(struct spi_slave *slave) 464 { 465 /* TODO: Shut the controller down */ 466 } 467