1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * Copyright (c) 2006 Ben Warren, Qstreams Networks Inc. 4 * With help from the common/soft_spi and arch/powerpc/cpu/mpc8260 drivers 5 */ 6 7 #include <common.h> 8 9 #include <malloc.h> 10 #include <spi.h> 11 #include <asm/mpc8xxx_spi.h> 12 13 #define SPI_EV_NE (0x80000000 >> 22) /* Receiver Not Empty */ 14 #define SPI_EV_NF (0x80000000 >> 23) /* Transmitter Not Full */ 15 16 #define SPI_MODE_LOOP (0x80000000 >> 1) /* Loopback mode */ 17 #define SPI_MODE_REV (0x80000000 >> 5) /* Reverse mode - MSB first */ 18 #define SPI_MODE_MS (0x80000000 >> 6) /* Always master */ 19 #define SPI_MODE_EN (0x80000000 >> 7) /* Enable interface */ 20 21 #define SPI_TIMEOUT 1000 22 23 struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs, 24 unsigned int max_hz, unsigned int mode) 25 { 26 struct spi_slave *slave; 27 28 if (!spi_cs_is_valid(bus, cs)) 29 return NULL; 30 31 slave = spi_alloc_slave_base(bus, cs); 32 if (!slave) 33 return NULL; 34 35 /* 36 * TODO: Some of the code in spi_init() should probably move 37 * here, or into spi_claim_bus() below. 38 */ 39 40 return slave; 41 } 42 43 void spi_free_slave(struct spi_slave *slave) 44 { 45 free(slave); 46 } 47 48 void spi_init(void) 49 { 50 volatile spi8xxx_t *spi = &((immap_t *) (CONFIG_SYS_IMMR))->spi; 51 52 /* 53 * SPI pins on the MPC83xx are not muxed, so all we do is initialize 54 * some registers 55 */ 56 spi->mode = SPI_MODE_REV | SPI_MODE_MS | SPI_MODE_EN; 57 spi->mode = (spi->mode & 0xfff0ffff) | BIT(16); /* Use SYSCLK / 8 58 (16.67MHz typ.) */ 59 spi->event = 0xffffffff; /* Clear all SPI events */ 60 spi->mask = 0x00000000; /* Mask all SPI interrupts */ 61 spi->com = 0; /* LST bit doesn't do anything, so disregard */ 62 } 63 64 int spi_claim_bus(struct spi_slave *slave) 65 { 66 return 0; 67 } 68 69 void spi_release_bus(struct spi_slave *slave) 70 { 71 72 } 73 74 int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *dout, 75 void *din, unsigned long flags) 76 { 77 volatile spi8xxx_t *spi = &((immap_t *) (CONFIG_SYS_IMMR))->spi; 78 unsigned int tmpdout, tmpdin, event; 79 int numBlks = DIV_ROUND_UP(bitlen, 32); 80 int tm, isRead = 0; 81 unsigned char charSize = 32; 82 83 debug("spi_xfer: slave %u:%u dout %08X din %08X bitlen %u\n", 84 slave->bus, slave->cs, *(uint *) dout, *(uint *) din, bitlen); 85 86 if (flags & SPI_XFER_BEGIN) 87 spi_cs_activate(slave); 88 89 spi->event = 0xffffffff; /* Clear all SPI events */ 90 91 /* handle data in 32-bit chunks */ 92 while (numBlks--) { 93 tmpdout = 0; 94 charSize = (bitlen >= 32 ? 32 : bitlen); 95 96 /* Shift data so it's msb-justified */ 97 tmpdout = *(u32 *) dout >> (32 - charSize); 98 99 /* The LEN field of the SPMODE register is set as follows: 100 * 101 * Bit length setting 102 * len <= 4 3 103 * 4 < len <= 16 len - 1 104 * len > 16 0 105 */ 106 107 spi->mode &= ~SPI_MODE_EN; 108 109 if (bitlen <= 16) { 110 if (bitlen <= 4) 111 spi->mode = (spi->mode & 0xff0fffff) | 112 (3 << 20); 113 else 114 spi->mode = (spi->mode & 0xff0fffff) | 115 ((bitlen - 1) << 20); 116 } else { 117 spi->mode = (spi->mode & 0xff0fffff); 118 /* Set up the next iteration if sending > 32 bits */ 119 bitlen -= 32; 120 dout += 4; 121 } 122 123 spi->mode |= SPI_MODE_EN; 124 125 spi->tx = tmpdout; /* Write the data out */ 126 debug("*** spi_xfer: ... %08x written\n", tmpdout); 127 128 /* 129 * Wait for SPI transmit to get out 130 * or time out (1 second = 1000 ms) 131 * The NE event must be read and cleared first 132 */ 133 for (tm = 0, isRead = 0; tm < SPI_TIMEOUT; ++tm) { 134 event = spi->event; 135 if (event & SPI_EV_NE) { 136 tmpdin = spi->rx; 137 spi->event |= SPI_EV_NE; 138 isRead = 1; 139 140 *(u32 *) din = (tmpdin << (32 - charSize)); 141 if (charSize == 32) { 142 /* Advance output buffer by 32 bits */ 143 din += 4; 144 } 145 } 146 /* 147 * Only bail when we've had both NE and NF events. 148 * This will cause timeouts on RO devices, so maybe 149 * in the future put an arbitrary delay after writing 150 * the device. Arbitrary delays suck, though... 151 */ 152 if (isRead && (event & SPI_EV_NF)) 153 break; 154 } 155 if (tm >= SPI_TIMEOUT) 156 puts("*** spi_xfer: Time out during SPI transfer"); 157 158 debug("*** spi_xfer: transfer ended. Value=%08x\n", tmpdin); 159 } 160 161 if (flags & SPI_XFER_END) 162 spi_cs_deactivate(slave); 163 164 return 0; 165 } 166