xref: /openbmc/u-boot/drivers/spi/kirkwood_spi.c (revision 23ff8633) 
1 /*
2  * (C) Copyright 2009
3  * Marvell Semiconductor <www.marvell.com>
4  * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
5  *
6  * Derived from drivers/spi/mpc8xxx_spi.c
7  *
8  * SPDX-License-Identifier:	GPL-2.0+
9  */
10 
11 #include <common.h>
12 #include <dm.h>
13 #include <malloc.h>
14 #include <spi.h>
15 #include <asm/io.h>
16 #include <asm/arch/soc.h>
17 #ifdef CONFIG_KIRKWOOD
18 #include <asm/arch/mpp.h>
19 #endif
20 #include <asm/arch-mvebu/spi.h>
21 
22 static void _spi_cs_activate(struct kwspi_registers *reg)
23 {
24 	setbits_le32(&reg->ctrl, KWSPI_CSN_ACT);
25 }
26 
27 static void _spi_cs_deactivate(struct kwspi_registers *reg)
28 {
29 	clrbits_le32(&reg->ctrl, KWSPI_CSN_ACT);
30 }
31 
32 static int _spi_xfer(struct kwspi_registers *reg, unsigned int bitlen,
33 		     const void *dout, void *din, unsigned long flags)
34 {
35 	unsigned int tmpdout, tmpdin;
36 	int tm, isread = 0;
37 
38 	debug("spi_xfer: dout %p din %p bitlen %u\n", dout, din, bitlen);
39 
40 	if (flags & SPI_XFER_BEGIN)
41 		_spi_cs_activate(reg);
42 
43 	/*
44 	 * handle data in 8-bit chunks
45 	 * TBD: 2byte xfer mode to be enabled
46 	 */
47 	clrsetbits_le32(&reg->cfg, KWSPI_XFERLEN_MASK, KWSPI_XFERLEN_1BYTE);
48 
49 	while (bitlen > 4) {
50 		debug("loopstart bitlen %d\n", bitlen);
51 		tmpdout = 0;
52 
53 		/* Shift data so it's msb-justified */
54 		if (dout)
55 			tmpdout = *(u32 *)dout & 0xff;
56 
57 		clrbits_le32(&reg->irq_cause, KWSPI_SMEMRDIRQ);
58 		writel(tmpdout, &reg->dout);	/* Write the data out */
59 		debug("*** spi_xfer: ... %08x written, bitlen %d\n",
60 		      tmpdout, bitlen);
61 
62 		/*
63 		 * Wait for SPI transmit to get out
64 		 * or time out (1 second = 1000 ms)
65 		 * The NE event must be read and cleared first
66 		 */
67 		for (tm = 0, isread = 0; tm < KWSPI_TIMEOUT; ++tm) {
68 			if (readl(&reg->irq_cause) & KWSPI_SMEMRDIRQ) {
69 				isread = 1;
70 				tmpdin = readl(&reg->din);
71 				debug("spi_xfer: din %p..%08x read\n",
72 				      din, tmpdin);
73 
74 				if (din) {
75 					*((u8 *)din) = (u8)tmpdin;
76 					din += 1;
77 				}
78 				if (dout)
79 					dout += 1;
80 				bitlen -= 8;
81 			}
82 			if (isread)
83 				break;
84 		}
85 		if (tm >= KWSPI_TIMEOUT)
86 			printf("*** spi_xfer: Time out during SPI transfer\n");
87 
88 		debug("loopend bitlen %d\n", bitlen);
89 	}
90 
91 	if (flags & SPI_XFER_END)
92 		_spi_cs_deactivate(reg);
93 
94 	return 0;
95 }
96 
97 #ifndef CONFIG_DM_SPI
98 
99 static struct kwspi_registers *spireg =
100 	(struct kwspi_registers *)MVEBU_SPI_BASE;
101 
102 #ifdef CONFIG_KIRKWOOD
103 static u32 cs_spi_mpp_back[2];
104 #endif
105 
106 struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
107 				unsigned int max_hz, unsigned int mode)
108 {
109 	struct spi_slave *slave;
110 	u32 data;
111 #ifdef CONFIG_KIRKWOOD
112 	static const u32 kwspi_mpp_config[2][2] = {
113 		{ MPP0_SPI_SCn, 0 }, /* if cs == 0 */
114 		{ MPP7_SPI_SCn, 0 } /* if cs != 0 */
115 	};
116 #endif
117 
118 	if (!spi_cs_is_valid(bus, cs))
119 		return NULL;
120 
121 	slave = spi_alloc_slave_base(bus, cs);
122 	if (!slave)
123 		return NULL;
124 
125 	writel(KWSPI_SMEMRDY, &spireg->ctrl);
126 
127 	/* calculate spi clock prescaller using max_hz */
128 	data = ((CONFIG_SYS_TCLK / 2) / max_hz) + 0x10;
129 	data = data < KWSPI_CLKPRESCL_MIN ? KWSPI_CLKPRESCL_MIN : data;
130 	data = data > KWSPI_CLKPRESCL_MASK ? KWSPI_CLKPRESCL_MASK : data;
131 
132 	/* program spi clock prescaller using max_hz */
133 	writel(KWSPI_ADRLEN_3BYTE | data, &spireg->cfg);
134 	debug("data = 0x%08x\n", data);
135 
136 	writel(KWSPI_SMEMRDIRQ, &spireg->irq_cause);
137 	writel(KWSPI_IRQMASK, &spireg->irq_mask);
138 
139 #ifdef CONFIG_KIRKWOOD
140 	/* program mpp registers to select  SPI_CSn */
141 	kirkwood_mpp_conf(kwspi_mpp_config[cs ? 1 : 0], cs_spi_mpp_back);
142 #endif
143 
144 	return slave;
145 }
146 
147 void spi_free_slave(struct spi_slave *slave)
148 {
149 #ifdef CONFIG_KIRKWOOD
150 	kirkwood_mpp_conf(cs_spi_mpp_back, NULL);
151 #endif
152 	free(slave);
153 }
154 
155 #if defined(CONFIG_SYS_KW_SPI_MPP)
156 u32 spi_mpp_backup[4];
157 #endif
158 
159 __attribute__((weak)) int board_spi_claim_bus(struct spi_slave *slave)
160 {
161 	return 0;
162 }
163 
164 int spi_claim_bus(struct spi_slave *slave)
165 {
166 #if defined(CONFIG_SYS_KW_SPI_MPP)
167 	u32 config;
168 	u32 spi_mpp_config[4];
169 
170 	config = CONFIG_SYS_KW_SPI_MPP;
171 
172 	if (config & MOSI_MPP6)
173 		spi_mpp_config[0] = MPP6_SPI_MOSI;
174 	else
175 		spi_mpp_config[0] = MPP1_SPI_MOSI;
176 
177 	if (config & SCK_MPP10)
178 		spi_mpp_config[1] = MPP10_SPI_SCK;
179 	else
180 		spi_mpp_config[1] = MPP2_SPI_SCK;
181 
182 	if (config & MISO_MPP11)
183 		spi_mpp_config[2] = MPP11_SPI_MISO;
184 	else
185 		spi_mpp_config[2] = MPP3_SPI_MISO;
186 
187 	spi_mpp_config[3] = 0;
188 	spi_mpp_backup[3] = 0;
189 
190 	/* set new spi mpp and save current mpp config */
191 	kirkwood_mpp_conf(spi_mpp_config, spi_mpp_backup);
192 #endif
193 
194 	return board_spi_claim_bus(slave);
195 }
196 
197 __attribute__((weak)) void board_spi_release_bus(struct spi_slave *slave)
198 {
199 }
200 
201 void spi_release_bus(struct spi_slave *slave)
202 {
203 #if defined(CONFIG_SYS_KW_SPI_MPP)
204 	kirkwood_mpp_conf(spi_mpp_backup, NULL);
205 #endif
206 
207 	board_spi_release_bus(slave);
208 }
209 
210 #ifndef CONFIG_SPI_CS_IS_VALID
211 /*
212  * you can define this function board specific
213  * define above CONFIG in board specific config file and
214  * provide the function in board specific src file
215  */
216 int spi_cs_is_valid(unsigned int bus, unsigned int cs)
217 {
218 	return bus == 0 && (cs == 0 || cs == 1);
219 }
220 #endif
221 
222 void spi_init(void)
223 {
224 }
225 
226 void spi_cs_activate(struct spi_slave *slave)
227 {
228 	_spi_cs_activate(spireg);
229 }
230 
231 void spi_cs_deactivate(struct spi_slave *slave)
232 {
233 	_spi_cs_deactivate(spireg);
234 }
235 
236 int spi_xfer(struct spi_slave *slave, unsigned int bitlen,
237 	     const void *dout, void *din, unsigned long flags)
238 {
239 	return _spi_xfer(spireg, bitlen, dout, din, flags);
240 }
241 
242 #else
243 
244 /* Here now the DM part */
245 
246 struct mvebu_spi_platdata {
247 	struct kwspi_registers *spireg;
248 };
249 
250 struct mvebu_spi_priv {
251 	struct kwspi_registers *spireg;
252 };
253 
254 static int mvebu_spi_set_speed(struct udevice *bus, uint hz)
255 {
256 	struct mvebu_spi_platdata *plat = dev_get_platdata(bus);
257 	struct kwspi_registers *reg = plat->spireg;
258 	u32 data;
259 
260 	/* calculate spi clock prescaller using max_hz */
261 	data = ((CONFIG_SYS_TCLK / 2) / hz) + 0x10;
262 	data = data < KWSPI_CLKPRESCL_MIN ? KWSPI_CLKPRESCL_MIN : data;
263 	data = data > KWSPI_CLKPRESCL_MASK ? KWSPI_CLKPRESCL_MASK : data;
264 
265 	/* program spi clock prescaler using max_hz */
266 	writel(KWSPI_ADRLEN_3BYTE | data, &reg->cfg);
267 	debug("data = 0x%08x\n", data);
268 
269 	return 0;
270 }
271 
272 static int mvebu_spi_set_mode(struct udevice *bus, uint mode)
273 {
274 	return 0;
275 }
276 
277 static int mvebu_spi_xfer(struct udevice *dev, unsigned int bitlen,
278 			  const void *dout, void *din, unsigned long flags)
279 {
280 	struct udevice *bus = dev->parent;
281 	struct mvebu_spi_platdata *plat = dev_get_platdata(bus);
282 
283 	return _spi_xfer(plat->spireg, bitlen, dout, din, flags);
284 }
285 
286 static int mvebu_spi_probe(struct udevice *bus)
287 {
288 	struct mvebu_spi_platdata *plat = dev_get_platdata(bus);
289 	struct kwspi_registers *reg = plat->spireg;
290 
291 	writel(KWSPI_SMEMRDY, &reg->ctrl);
292 	writel(KWSPI_SMEMRDIRQ, &reg->irq_cause);
293 	writel(KWSPI_IRQMASK, &reg->irq_mask);
294 
295 	return 0;
296 }
297 
298 static int mvebu_spi_ofdata_to_platdata(struct udevice *bus)
299 {
300 	struct mvebu_spi_platdata *plat = dev_get_platdata(bus);
301 
302 	plat->spireg = (struct kwspi_registers *)dev_get_addr(bus);
303 
304 	return 0;
305 }
306 
307 static const struct dm_spi_ops mvebu_spi_ops = {
308 	.xfer		= mvebu_spi_xfer,
309 	.set_speed	= mvebu_spi_set_speed,
310 	.set_mode	= mvebu_spi_set_mode,
311 	/*
312 	 * cs_info is not needed, since we require all chip selects to be
313 	 * in the device tree explicitly
314 	 */
315 };
316 
317 static const struct udevice_id mvebu_spi_ids[] = {
318 	{ .compatible = "marvell,armada-380-spi" },
319 	{ .compatible = "marvell,armada-xp-spi" },
320 	{ }
321 };
322 
323 U_BOOT_DRIVER(mvebu_spi) = {
324 	.name = "mvebu_spi",
325 	.id = UCLASS_SPI,
326 	.of_match = mvebu_spi_ids,
327 	.ops = &mvebu_spi_ops,
328 	.ofdata_to_platdata = mvebu_spi_ofdata_to_platdata,
329 	.platdata_auto_alloc_size = sizeof(struct mvebu_spi_platdata),
330 	.priv_auto_alloc_size = sizeof(struct mvebu_spi_priv),
331 	.probe = mvebu_spi_probe,
332 };
333 #endif
334