1 /* 2 * Copyright 2013-2015 Freescale Semiconductor, Inc. 3 * 4 * Freescale Quad Serial Peripheral Interface (QSPI) driver 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #include <common.h> 10 #include <malloc.h> 11 #include <spi.h> 12 #include <asm/io.h> 13 #include <linux/sizes.h> 14 #include <dm.h> 15 #include <errno.h> 16 #include <watchdog.h> 17 #include "fsl_qspi.h" 18 19 DECLARE_GLOBAL_DATA_PTR; 20 21 #define RX_BUFFER_SIZE 0x80 22 #ifdef CONFIG_MX6SX 23 #define TX_BUFFER_SIZE 0x200 24 #else 25 #define TX_BUFFER_SIZE 0x40 26 #endif 27 28 #define OFFSET_BITS_MASK GENMASK(23, 0) 29 30 #define FLASH_STATUS_WEL 0x02 31 32 /* SEQID */ 33 #define SEQID_WREN 1 34 #define SEQID_FAST_READ 2 35 #define SEQID_RDSR 3 36 #define SEQID_SE 4 37 #define SEQID_CHIP_ERASE 5 38 #define SEQID_PP 6 39 #define SEQID_RDID 7 40 #define SEQID_BE_4K 8 41 #ifdef CONFIG_SPI_FLASH_BAR 42 #define SEQID_BRRD 9 43 #define SEQID_BRWR 10 44 #define SEQID_RDEAR 11 45 #define SEQID_WREAR 12 46 #endif 47 #define SEQID_WRAR 13 48 #define SEQID_RDAR 14 49 50 /* QSPI CMD */ 51 #define QSPI_CMD_PP 0x02 /* Page program (up to 256 bytes) */ 52 #define QSPI_CMD_RDSR 0x05 /* Read status register */ 53 #define QSPI_CMD_WREN 0x06 /* Write enable */ 54 #define QSPI_CMD_FAST_READ 0x0b /* Read data bytes (high frequency) */ 55 #define QSPI_CMD_BE_4K 0x20 /* 4K erase */ 56 #define QSPI_CMD_CHIP_ERASE 0xc7 /* Erase whole flash chip */ 57 #define QSPI_CMD_SE 0xd8 /* Sector erase (usually 64KiB) */ 58 #define QSPI_CMD_RDID 0x9f /* Read JEDEC ID */ 59 60 /* Used for Micron, winbond and Macronix flashes */ 61 #define QSPI_CMD_WREAR 0xc5 /* EAR register write */ 62 #define QSPI_CMD_RDEAR 0xc8 /* EAR reigster read */ 63 64 /* Used for Spansion flashes only. */ 65 #define QSPI_CMD_BRRD 0x16 /* Bank register read */ 66 #define QSPI_CMD_BRWR 0x17 /* Bank register write */ 67 68 /* Used for Spansion S25FS-S family flash only. */ 69 #define QSPI_CMD_RDAR 0x65 /* Read any device register */ 70 #define QSPI_CMD_WRAR 0x71 /* Write any device register */ 71 72 /* 4-byte address QSPI CMD - used on Spansion and some Macronix flashes */ 73 #define QSPI_CMD_FAST_READ_4B 0x0c /* Read data bytes (high frequency) */ 74 #define QSPI_CMD_PP_4B 0x12 /* Page program (up to 256 bytes) */ 75 #define QSPI_CMD_SE_4B 0xdc /* Sector erase (usually 64KiB) */ 76 77 /* fsl_qspi_platdata flags */ 78 #define QSPI_FLAG_REGMAP_ENDIAN_BIG BIT(0) 79 80 /* default SCK frequency, unit: HZ */ 81 #define FSL_QSPI_DEFAULT_SCK_FREQ 50000000 82 83 /* QSPI max chipselect signals number */ 84 #define FSL_QSPI_MAX_CHIPSELECT_NUM 4 85 86 #ifdef CONFIG_DM_SPI 87 /** 88 * struct fsl_qspi_platdata - platform data for Freescale QSPI 89 * 90 * @flags: Flags for QSPI QSPI_FLAG_... 91 * @speed_hz: Default SCK frequency 92 * @reg_base: Base address of QSPI registers 93 * @amba_base: Base address of QSPI memory mapping 94 * @amba_total_size: size of QSPI memory mapping 95 * @flash_num: Number of active slave devices 96 * @num_chipselect: Number of QSPI chipselect signals 97 */ 98 struct fsl_qspi_platdata { 99 u32 flags; 100 u32 speed_hz; 101 fdt_addr_t reg_base; 102 fdt_addr_t amba_base; 103 fdt_size_t amba_total_size; 104 u32 flash_num; 105 u32 num_chipselect; 106 }; 107 #endif 108 109 /** 110 * struct fsl_qspi_priv - private data for Freescale QSPI 111 * 112 * @flags: Flags for QSPI QSPI_FLAG_... 113 * @bus_clk: QSPI input clk frequency 114 * @speed_hz: Default SCK frequency 115 * @cur_seqid: current LUT table sequence id 116 * @sf_addr: flash access offset 117 * @amba_base: Base address of QSPI memory mapping of every CS 118 * @amba_total_size: size of QSPI memory mapping 119 * @cur_amba_base: Base address of QSPI memory mapping of current CS 120 * @flash_num: Number of active slave devices 121 * @num_chipselect: Number of QSPI chipselect signals 122 * @regs: Point to QSPI register structure for I/O access 123 */ 124 struct fsl_qspi_priv { 125 u32 flags; 126 u32 bus_clk; 127 u32 speed_hz; 128 u32 cur_seqid; 129 u32 sf_addr; 130 u32 amba_base[FSL_QSPI_MAX_CHIPSELECT_NUM]; 131 u32 amba_total_size; 132 u32 cur_amba_base; 133 u32 flash_num; 134 u32 num_chipselect; 135 struct fsl_qspi_regs *regs; 136 }; 137 138 #ifndef CONFIG_DM_SPI 139 struct fsl_qspi { 140 struct spi_slave slave; 141 struct fsl_qspi_priv priv; 142 }; 143 #endif 144 145 static u32 qspi_read32(u32 flags, u32 *addr) 146 { 147 return flags & QSPI_FLAG_REGMAP_ENDIAN_BIG ? 148 in_be32(addr) : in_le32(addr); 149 } 150 151 static void qspi_write32(u32 flags, u32 *addr, u32 val) 152 { 153 flags & QSPI_FLAG_REGMAP_ENDIAN_BIG ? 154 out_be32(addr, val) : out_le32(addr, val); 155 } 156 157 /* QSPI support swapping the flash read/write data 158 * in hardware for LS102xA, but not for VF610 */ 159 static inline u32 qspi_endian_xchg(u32 data) 160 { 161 #ifdef CONFIG_VF610 162 return swab32(data); 163 #else 164 return data; 165 #endif 166 } 167 168 static void qspi_set_lut(struct fsl_qspi_priv *priv) 169 { 170 struct fsl_qspi_regs *regs = priv->regs; 171 u32 lut_base; 172 173 /* Unlock the LUT */ 174 qspi_write32(priv->flags, ®s->lutkey, LUT_KEY_VALUE); 175 qspi_write32(priv->flags, ®s->lckcr, QSPI_LCKCR_UNLOCK); 176 177 /* Write Enable */ 178 lut_base = SEQID_WREN * 4; 179 qspi_write32(priv->flags, ®s->lut[lut_base], OPRND0(QSPI_CMD_WREN) | 180 PAD0(LUT_PAD1) | INSTR0(LUT_CMD)); 181 qspi_write32(priv->flags, ®s->lut[lut_base + 1], 0); 182 qspi_write32(priv->flags, ®s->lut[lut_base + 2], 0); 183 qspi_write32(priv->flags, ®s->lut[lut_base + 3], 0); 184 185 /* Fast Read */ 186 lut_base = SEQID_FAST_READ * 4; 187 #ifdef CONFIG_SPI_FLASH_BAR 188 qspi_write32(priv->flags, ®s->lut[lut_base], 189 OPRND0(QSPI_CMD_FAST_READ) | PAD0(LUT_PAD1) | 190 INSTR0(LUT_CMD) | OPRND1(ADDR24BIT) | 191 PAD1(LUT_PAD1) | INSTR1(LUT_ADDR)); 192 #else 193 if (FSL_QSPI_FLASH_SIZE <= SZ_16M) 194 qspi_write32(priv->flags, ®s->lut[lut_base], 195 OPRND0(QSPI_CMD_FAST_READ) | PAD0(LUT_PAD1) | 196 INSTR0(LUT_CMD) | OPRND1(ADDR24BIT) | 197 PAD1(LUT_PAD1) | INSTR1(LUT_ADDR)); 198 else 199 qspi_write32(priv->flags, ®s->lut[lut_base], 200 OPRND0(QSPI_CMD_FAST_READ_4B) | 201 PAD0(LUT_PAD1) | INSTR0(LUT_CMD) | 202 OPRND1(ADDR32BIT) | PAD1(LUT_PAD1) | 203 INSTR1(LUT_ADDR)); 204 #endif 205 qspi_write32(priv->flags, ®s->lut[lut_base + 1], 206 OPRND0(8) | PAD0(LUT_PAD1) | INSTR0(LUT_DUMMY) | 207 OPRND1(RX_BUFFER_SIZE) | PAD1(LUT_PAD1) | 208 INSTR1(LUT_READ)); 209 qspi_write32(priv->flags, ®s->lut[lut_base + 2], 0); 210 qspi_write32(priv->flags, ®s->lut[lut_base + 3], 0); 211 212 /* Read Status */ 213 lut_base = SEQID_RDSR * 4; 214 qspi_write32(priv->flags, ®s->lut[lut_base], OPRND0(QSPI_CMD_RDSR) | 215 PAD0(LUT_PAD1) | INSTR0(LUT_CMD) | OPRND1(1) | 216 PAD1(LUT_PAD1) | INSTR1(LUT_READ)); 217 qspi_write32(priv->flags, ®s->lut[lut_base + 1], 0); 218 qspi_write32(priv->flags, ®s->lut[lut_base + 2], 0); 219 qspi_write32(priv->flags, ®s->lut[lut_base + 3], 0); 220 221 /* Erase a sector */ 222 lut_base = SEQID_SE * 4; 223 #ifdef CONFIG_SPI_FLASH_BAR 224 qspi_write32(priv->flags, ®s->lut[lut_base], OPRND0(QSPI_CMD_SE) | 225 PAD0(LUT_PAD1) | INSTR0(LUT_CMD) | OPRND1(ADDR24BIT) | 226 PAD1(LUT_PAD1) | INSTR1(LUT_ADDR)); 227 #else 228 if (FSL_QSPI_FLASH_SIZE <= SZ_16M) 229 qspi_write32(priv->flags, ®s->lut[lut_base], 230 OPRND0(QSPI_CMD_SE) | PAD0(LUT_PAD1) | 231 INSTR0(LUT_CMD) | OPRND1(ADDR24BIT) | 232 PAD1(LUT_PAD1) | INSTR1(LUT_ADDR)); 233 else 234 qspi_write32(priv->flags, ®s->lut[lut_base], 235 OPRND0(QSPI_CMD_SE_4B) | PAD0(LUT_PAD1) | 236 INSTR0(LUT_CMD) | OPRND1(ADDR32BIT) | 237 PAD1(LUT_PAD1) | INSTR1(LUT_ADDR)); 238 #endif 239 qspi_write32(priv->flags, ®s->lut[lut_base + 1], 0); 240 qspi_write32(priv->flags, ®s->lut[lut_base + 2], 0); 241 qspi_write32(priv->flags, ®s->lut[lut_base + 3], 0); 242 243 /* Erase the whole chip */ 244 lut_base = SEQID_CHIP_ERASE * 4; 245 qspi_write32(priv->flags, ®s->lut[lut_base], 246 OPRND0(QSPI_CMD_CHIP_ERASE) | 247 PAD0(LUT_PAD1) | INSTR0(LUT_CMD)); 248 qspi_write32(priv->flags, ®s->lut[lut_base + 1], 0); 249 qspi_write32(priv->flags, ®s->lut[lut_base + 2], 0); 250 qspi_write32(priv->flags, ®s->lut[lut_base + 3], 0); 251 252 /* Page Program */ 253 lut_base = SEQID_PP * 4; 254 #ifdef CONFIG_SPI_FLASH_BAR 255 qspi_write32(priv->flags, ®s->lut[lut_base], OPRND0(QSPI_CMD_PP) | 256 PAD0(LUT_PAD1) | INSTR0(LUT_CMD) | OPRND1(ADDR24BIT) | 257 PAD1(LUT_PAD1) | INSTR1(LUT_ADDR)); 258 #else 259 if (FSL_QSPI_FLASH_SIZE <= SZ_16M) 260 qspi_write32(priv->flags, ®s->lut[lut_base], 261 OPRND0(QSPI_CMD_PP) | PAD0(LUT_PAD1) | 262 INSTR0(LUT_CMD) | OPRND1(ADDR24BIT) | 263 PAD1(LUT_PAD1) | INSTR1(LUT_ADDR)); 264 else 265 qspi_write32(priv->flags, ®s->lut[lut_base], 266 OPRND0(QSPI_CMD_PP_4B) | PAD0(LUT_PAD1) | 267 INSTR0(LUT_CMD) | OPRND1(ADDR32BIT) | 268 PAD1(LUT_PAD1) | INSTR1(LUT_ADDR)); 269 #endif 270 #ifdef CONFIG_MX6SX 271 /* 272 * To MX6SX, OPRND0(TX_BUFFER_SIZE) can not work correctly. 273 * So, Use IDATSZ in IPCR to determine the size and here set 0. 274 */ 275 qspi_write32(priv->flags, ®s->lut[lut_base + 1], OPRND0(0) | 276 PAD0(LUT_PAD1) | INSTR0(LUT_WRITE)); 277 #else 278 qspi_write32(priv->flags, ®s->lut[lut_base + 1], 279 OPRND0(TX_BUFFER_SIZE) | 280 PAD0(LUT_PAD1) | INSTR0(LUT_WRITE)); 281 #endif 282 qspi_write32(priv->flags, ®s->lut[lut_base + 2], 0); 283 qspi_write32(priv->flags, ®s->lut[lut_base + 3], 0); 284 285 /* READ ID */ 286 lut_base = SEQID_RDID * 4; 287 qspi_write32(priv->flags, ®s->lut[lut_base], OPRND0(QSPI_CMD_RDID) | 288 PAD0(LUT_PAD1) | INSTR0(LUT_CMD) | OPRND1(8) | 289 PAD1(LUT_PAD1) | INSTR1(LUT_READ)); 290 qspi_write32(priv->flags, ®s->lut[lut_base + 1], 0); 291 qspi_write32(priv->flags, ®s->lut[lut_base + 2], 0); 292 qspi_write32(priv->flags, ®s->lut[lut_base + 3], 0); 293 294 /* SUB SECTOR 4K ERASE */ 295 lut_base = SEQID_BE_4K * 4; 296 qspi_write32(priv->flags, ®s->lut[lut_base], OPRND0(QSPI_CMD_BE_4K) | 297 PAD0(LUT_PAD1) | INSTR0(LUT_CMD) | OPRND1(ADDR24BIT) | 298 PAD1(LUT_PAD1) | INSTR1(LUT_ADDR)); 299 300 #ifdef CONFIG_SPI_FLASH_BAR 301 /* 302 * BRRD BRWR RDEAR WREAR are all supported, because it is hard to 303 * dynamically check whether to set BRRD BRWR or RDEAR WREAR during 304 * initialization. 305 */ 306 lut_base = SEQID_BRRD * 4; 307 qspi_write32(priv->flags, ®s->lut[lut_base], OPRND0(QSPI_CMD_BRRD) | 308 PAD0(LUT_PAD1) | INSTR0(LUT_CMD) | OPRND1(1) | 309 PAD1(LUT_PAD1) | INSTR1(LUT_READ)); 310 311 lut_base = SEQID_BRWR * 4; 312 qspi_write32(priv->flags, ®s->lut[lut_base], OPRND0(QSPI_CMD_BRWR) | 313 PAD0(LUT_PAD1) | INSTR0(LUT_CMD) | OPRND1(1) | 314 PAD1(LUT_PAD1) | INSTR1(LUT_WRITE)); 315 316 lut_base = SEQID_RDEAR * 4; 317 qspi_write32(priv->flags, ®s->lut[lut_base], OPRND0(QSPI_CMD_RDEAR) | 318 PAD0(LUT_PAD1) | INSTR0(LUT_CMD) | OPRND1(1) | 319 PAD1(LUT_PAD1) | INSTR1(LUT_READ)); 320 321 lut_base = SEQID_WREAR * 4; 322 qspi_write32(priv->flags, ®s->lut[lut_base], OPRND0(QSPI_CMD_WREAR) | 323 PAD0(LUT_PAD1) | INSTR0(LUT_CMD) | OPRND1(1) | 324 PAD1(LUT_PAD1) | INSTR1(LUT_WRITE)); 325 #endif 326 327 /* 328 * Read any device register. 329 * Used for Spansion S25FS-S family flash only. 330 */ 331 lut_base = SEQID_RDAR * 4; 332 qspi_write32(priv->flags, ®s->lut[lut_base], 333 OPRND0(QSPI_CMD_RDAR) | PAD0(LUT_PAD1) | 334 INSTR0(LUT_CMD) | OPRND1(ADDR24BIT) | 335 PAD1(LUT_PAD1) | INSTR1(LUT_ADDR)); 336 qspi_write32(priv->flags, ®s->lut[lut_base + 1], 337 OPRND0(8) | PAD0(LUT_PAD1) | INSTR0(LUT_DUMMY) | 338 OPRND1(1) | PAD1(LUT_PAD1) | 339 INSTR1(LUT_READ)); 340 341 /* 342 * Write any device register. 343 * Used for Spansion S25FS-S family flash only. 344 */ 345 lut_base = SEQID_WRAR * 4; 346 qspi_write32(priv->flags, ®s->lut[lut_base], 347 OPRND0(QSPI_CMD_WRAR) | PAD0(LUT_PAD1) | 348 INSTR0(LUT_CMD) | OPRND1(ADDR24BIT) | 349 PAD1(LUT_PAD1) | INSTR1(LUT_ADDR)); 350 qspi_write32(priv->flags, ®s->lut[lut_base + 1], 351 OPRND0(1) | PAD0(LUT_PAD1) | INSTR0(LUT_WRITE)); 352 353 /* Lock the LUT */ 354 qspi_write32(priv->flags, ®s->lutkey, LUT_KEY_VALUE); 355 qspi_write32(priv->flags, ®s->lckcr, QSPI_LCKCR_LOCK); 356 } 357 358 #if defined(CONFIG_SYS_FSL_QSPI_AHB) 359 /* 360 * If we have changed the content of the flash by writing or erasing, 361 * we need to invalidate the AHB buffer. If we do not do so, we may read out 362 * the wrong data. The spec tells us reset the AHB domain and Serial Flash 363 * domain at the same time. 364 */ 365 static inline void qspi_ahb_invalid(struct fsl_qspi_priv *priv) 366 { 367 struct fsl_qspi_regs *regs = priv->regs; 368 u32 reg; 369 370 reg = qspi_read32(priv->flags, ®s->mcr); 371 reg |= QSPI_MCR_SWRSTHD_MASK | QSPI_MCR_SWRSTSD_MASK; 372 qspi_write32(priv->flags, ®s->mcr, reg); 373 374 /* 375 * The minimum delay : 1 AHB + 2 SFCK clocks. 376 * Delay 1 us is enough. 377 */ 378 udelay(1); 379 380 reg &= ~(QSPI_MCR_SWRSTHD_MASK | QSPI_MCR_SWRSTSD_MASK); 381 qspi_write32(priv->flags, ®s->mcr, reg); 382 } 383 384 /* Read out the data from the AHB buffer. */ 385 static inline void qspi_ahb_read(struct fsl_qspi_priv *priv, u8 *rxbuf, int len) 386 { 387 struct fsl_qspi_regs *regs = priv->regs; 388 u32 mcr_reg; 389 void *rx_addr = NULL; 390 391 mcr_reg = qspi_read32(priv->flags, ®s->mcr); 392 393 qspi_write32(priv->flags, ®s->mcr, 394 QSPI_MCR_CLR_RXF_MASK | QSPI_MCR_CLR_TXF_MASK | 395 QSPI_MCR_RESERVED_MASK | QSPI_MCR_END_CFD_LE); 396 397 rx_addr = (void *)(uintptr_t)(priv->cur_amba_base + priv->sf_addr); 398 /* Read out the data directly from the AHB buffer. */ 399 memcpy(rxbuf, rx_addr, len); 400 401 qspi_write32(priv->flags, ®s->mcr, mcr_reg); 402 } 403 404 static void qspi_enable_ddr_mode(struct fsl_qspi_priv *priv) 405 { 406 u32 reg, reg2; 407 struct fsl_qspi_regs *regs = priv->regs; 408 409 reg = qspi_read32(priv->flags, ®s->mcr); 410 /* Disable the module */ 411 qspi_write32(priv->flags, ®s->mcr, reg | QSPI_MCR_MDIS_MASK); 412 413 /* Set the Sampling Register for DDR */ 414 reg2 = qspi_read32(priv->flags, ®s->smpr); 415 reg2 &= ~QSPI_SMPR_DDRSMP_MASK; 416 reg2 |= (2 << QSPI_SMPR_DDRSMP_SHIFT); 417 qspi_write32(priv->flags, ®s->smpr, reg2); 418 419 /* Enable the module again (enable the DDR too) */ 420 reg |= QSPI_MCR_DDR_EN_MASK; 421 /* Enable bit 29 for imx6sx */ 422 reg |= BIT(29); 423 424 qspi_write32(priv->flags, ®s->mcr, reg); 425 } 426 427 /* 428 * There are two different ways to read out the data from the flash: 429 * the "IP Command Read" and the "AHB Command Read". 430 * 431 * The IC guy suggests we use the "AHB Command Read" which is faster 432 * then the "IP Command Read". (What's more is that there is a bug in 433 * the "IP Command Read" in the Vybrid.) 434 * 435 * After we set up the registers for the "AHB Command Read", we can use 436 * the memcpy to read the data directly. A "missed" access to the buffer 437 * causes the controller to clear the buffer, and use the sequence pointed 438 * by the QUADSPI_BFGENCR[SEQID] to initiate a read from the flash. 439 */ 440 static void qspi_init_ahb_read(struct fsl_qspi_priv *priv) 441 { 442 struct fsl_qspi_regs *regs = priv->regs; 443 444 /* AHB configuration for access buffer 0/1/2 .*/ 445 qspi_write32(priv->flags, ®s->buf0cr, QSPI_BUFXCR_INVALID_MSTRID); 446 qspi_write32(priv->flags, ®s->buf1cr, QSPI_BUFXCR_INVALID_MSTRID); 447 qspi_write32(priv->flags, ®s->buf2cr, QSPI_BUFXCR_INVALID_MSTRID); 448 qspi_write32(priv->flags, ®s->buf3cr, QSPI_BUF3CR_ALLMST_MASK | 449 (0x80 << QSPI_BUF3CR_ADATSZ_SHIFT)); 450 451 /* We only use the buffer3 */ 452 qspi_write32(priv->flags, ®s->buf0ind, 0); 453 qspi_write32(priv->flags, ®s->buf1ind, 0); 454 qspi_write32(priv->flags, ®s->buf2ind, 0); 455 456 /* 457 * Set the default lut sequence for AHB Read. 458 * Parallel mode is disabled. 459 */ 460 qspi_write32(priv->flags, ®s->bfgencr, 461 SEQID_FAST_READ << QSPI_BFGENCR_SEQID_SHIFT); 462 463 /*Enable DDR Mode*/ 464 qspi_enable_ddr_mode(priv); 465 } 466 #endif 467 468 #ifdef CONFIG_SPI_FLASH_BAR 469 /* Bank register read/write, EAR register read/write */ 470 static void qspi_op_rdbank(struct fsl_qspi_priv *priv, u8 *rxbuf, u32 len) 471 { 472 struct fsl_qspi_regs *regs = priv->regs; 473 u32 reg, mcr_reg, data, seqid; 474 475 mcr_reg = qspi_read32(priv->flags, ®s->mcr); 476 qspi_write32(priv->flags, ®s->mcr, 477 QSPI_MCR_CLR_RXF_MASK | QSPI_MCR_CLR_TXF_MASK | 478 QSPI_MCR_RESERVED_MASK | QSPI_MCR_END_CFD_LE); 479 qspi_write32(priv->flags, ®s->rbct, QSPI_RBCT_RXBRD_USEIPS); 480 481 qspi_write32(priv->flags, ®s->sfar, priv->cur_amba_base); 482 483 if (priv->cur_seqid == QSPI_CMD_BRRD) 484 seqid = SEQID_BRRD; 485 else 486 seqid = SEQID_RDEAR; 487 488 qspi_write32(priv->flags, ®s->ipcr, 489 (seqid << QSPI_IPCR_SEQID_SHIFT) | len); 490 491 /* Wait previous command complete */ 492 while (qspi_read32(priv->flags, ®s->sr) & QSPI_SR_BUSY_MASK) 493 ; 494 495 while (1) { 496 reg = qspi_read32(priv->flags, ®s->rbsr); 497 if (reg & QSPI_RBSR_RDBFL_MASK) { 498 data = qspi_read32(priv->flags, ®s->rbdr[0]); 499 data = qspi_endian_xchg(data); 500 memcpy(rxbuf, &data, len); 501 qspi_write32(priv->flags, ®s->mcr, 502 qspi_read32(priv->flags, ®s->mcr) | 503 QSPI_MCR_CLR_RXF_MASK); 504 break; 505 } 506 } 507 508 qspi_write32(priv->flags, ®s->mcr, mcr_reg); 509 } 510 #endif 511 512 static void qspi_op_rdid(struct fsl_qspi_priv *priv, u32 *rxbuf, u32 len) 513 { 514 struct fsl_qspi_regs *regs = priv->regs; 515 u32 mcr_reg, rbsr_reg, data, size; 516 int i; 517 518 mcr_reg = qspi_read32(priv->flags, ®s->mcr); 519 qspi_write32(priv->flags, ®s->mcr, 520 QSPI_MCR_CLR_RXF_MASK | QSPI_MCR_CLR_TXF_MASK | 521 QSPI_MCR_RESERVED_MASK | QSPI_MCR_END_CFD_LE); 522 qspi_write32(priv->flags, ®s->rbct, QSPI_RBCT_RXBRD_USEIPS); 523 524 qspi_write32(priv->flags, ®s->sfar, priv->cur_amba_base); 525 526 qspi_write32(priv->flags, ®s->ipcr, 527 (SEQID_RDID << QSPI_IPCR_SEQID_SHIFT) | 0); 528 while (qspi_read32(priv->flags, ®s->sr) & QSPI_SR_BUSY_MASK) 529 ; 530 531 i = 0; 532 while ((RX_BUFFER_SIZE >= len) && (len > 0)) { 533 rbsr_reg = qspi_read32(priv->flags, ®s->rbsr); 534 if (rbsr_reg & QSPI_RBSR_RDBFL_MASK) { 535 data = qspi_read32(priv->flags, ®s->rbdr[i]); 536 data = qspi_endian_xchg(data); 537 size = (len < 4) ? len : 4; 538 memcpy(rxbuf, &data, size); 539 len -= size; 540 rxbuf++; 541 i++; 542 } 543 } 544 545 qspi_write32(priv->flags, ®s->mcr, mcr_reg); 546 } 547 548 /* If not use AHB read, read data from ip interface */ 549 static void qspi_op_read(struct fsl_qspi_priv *priv, u32 *rxbuf, u32 len) 550 { 551 struct fsl_qspi_regs *regs = priv->regs; 552 u32 mcr_reg, data; 553 int i, size; 554 u32 to_or_from; 555 u32 seqid; 556 557 if (priv->cur_seqid == QSPI_CMD_RDAR) 558 seqid = SEQID_RDAR; 559 else 560 seqid = SEQID_FAST_READ; 561 562 mcr_reg = qspi_read32(priv->flags, ®s->mcr); 563 qspi_write32(priv->flags, ®s->mcr, 564 QSPI_MCR_CLR_RXF_MASK | QSPI_MCR_CLR_TXF_MASK | 565 QSPI_MCR_RESERVED_MASK | QSPI_MCR_END_CFD_LE); 566 qspi_write32(priv->flags, ®s->rbct, QSPI_RBCT_RXBRD_USEIPS); 567 568 to_or_from = priv->sf_addr + priv->cur_amba_base; 569 570 while (len > 0) { 571 WATCHDOG_RESET(); 572 573 qspi_write32(priv->flags, ®s->sfar, to_or_from); 574 575 size = (len > RX_BUFFER_SIZE) ? 576 RX_BUFFER_SIZE : len; 577 578 qspi_write32(priv->flags, ®s->ipcr, 579 (seqid << QSPI_IPCR_SEQID_SHIFT) | 580 size); 581 while (qspi_read32(priv->flags, ®s->sr) & QSPI_SR_BUSY_MASK) 582 ; 583 584 to_or_from += size; 585 len -= size; 586 587 i = 0; 588 while ((RX_BUFFER_SIZE >= size) && (size > 0)) { 589 data = qspi_read32(priv->flags, ®s->rbdr[i]); 590 data = qspi_endian_xchg(data); 591 if (size < 4) 592 memcpy(rxbuf, &data, size); 593 else 594 memcpy(rxbuf, &data, 4); 595 rxbuf++; 596 size -= 4; 597 i++; 598 } 599 qspi_write32(priv->flags, ®s->mcr, 600 qspi_read32(priv->flags, ®s->mcr) | 601 QSPI_MCR_CLR_RXF_MASK); 602 } 603 604 qspi_write32(priv->flags, ®s->mcr, mcr_reg); 605 } 606 607 static void qspi_op_write(struct fsl_qspi_priv *priv, u8 *txbuf, u32 len) 608 { 609 struct fsl_qspi_regs *regs = priv->regs; 610 u32 mcr_reg, data, reg, status_reg, seqid; 611 int i, size, tx_size; 612 u32 to_or_from = 0; 613 614 mcr_reg = qspi_read32(priv->flags, ®s->mcr); 615 qspi_write32(priv->flags, ®s->mcr, 616 QSPI_MCR_CLR_RXF_MASK | QSPI_MCR_CLR_TXF_MASK | 617 QSPI_MCR_RESERVED_MASK | QSPI_MCR_END_CFD_LE); 618 qspi_write32(priv->flags, ®s->rbct, QSPI_RBCT_RXBRD_USEIPS); 619 620 status_reg = 0; 621 while ((status_reg & FLASH_STATUS_WEL) != FLASH_STATUS_WEL) { 622 WATCHDOG_RESET(); 623 624 qspi_write32(priv->flags, ®s->ipcr, 625 (SEQID_WREN << QSPI_IPCR_SEQID_SHIFT) | 0); 626 while (qspi_read32(priv->flags, ®s->sr) & QSPI_SR_BUSY_MASK) 627 ; 628 629 qspi_write32(priv->flags, ®s->ipcr, 630 (SEQID_RDSR << QSPI_IPCR_SEQID_SHIFT) | 1); 631 while (qspi_read32(priv->flags, ®s->sr) & QSPI_SR_BUSY_MASK) 632 ; 633 634 reg = qspi_read32(priv->flags, ®s->rbsr); 635 if (reg & QSPI_RBSR_RDBFL_MASK) { 636 status_reg = qspi_read32(priv->flags, ®s->rbdr[0]); 637 status_reg = qspi_endian_xchg(status_reg); 638 } 639 qspi_write32(priv->flags, ®s->mcr, 640 qspi_read32(priv->flags, ®s->mcr) | 641 QSPI_MCR_CLR_RXF_MASK); 642 } 643 644 /* Default is page programming */ 645 seqid = SEQID_PP; 646 if (priv->cur_seqid == QSPI_CMD_WRAR) 647 seqid = SEQID_WRAR; 648 #ifdef CONFIG_SPI_FLASH_BAR 649 if (priv->cur_seqid == QSPI_CMD_BRWR) 650 seqid = SEQID_BRWR; 651 else if (priv->cur_seqid == QSPI_CMD_WREAR) 652 seqid = SEQID_WREAR; 653 #endif 654 655 to_or_from = priv->sf_addr + priv->cur_amba_base; 656 657 qspi_write32(priv->flags, ®s->sfar, to_or_from); 658 659 tx_size = (len > TX_BUFFER_SIZE) ? 660 TX_BUFFER_SIZE : len; 661 662 size = tx_size / 4; 663 for (i = 0; i < size; i++) { 664 memcpy(&data, txbuf, 4); 665 data = qspi_endian_xchg(data); 666 qspi_write32(priv->flags, ®s->tbdr, data); 667 txbuf += 4; 668 } 669 670 size = tx_size % 4; 671 if (size) { 672 data = 0; 673 memcpy(&data, txbuf, size); 674 data = qspi_endian_xchg(data); 675 qspi_write32(priv->flags, ®s->tbdr, data); 676 } 677 678 qspi_write32(priv->flags, ®s->ipcr, 679 (seqid << QSPI_IPCR_SEQID_SHIFT) | tx_size); 680 while (qspi_read32(priv->flags, ®s->sr) & QSPI_SR_BUSY_MASK) 681 ; 682 683 qspi_write32(priv->flags, ®s->mcr, mcr_reg); 684 } 685 686 static void qspi_op_rdsr(struct fsl_qspi_priv *priv, void *rxbuf, u32 len) 687 { 688 struct fsl_qspi_regs *regs = priv->regs; 689 u32 mcr_reg, reg, data; 690 691 mcr_reg = qspi_read32(priv->flags, ®s->mcr); 692 qspi_write32(priv->flags, ®s->mcr, 693 QSPI_MCR_CLR_RXF_MASK | QSPI_MCR_CLR_TXF_MASK | 694 QSPI_MCR_RESERVED_MASK | QSPI_MCR_END_CFD_LE); 695 qspi_write32(priv->flags, ®s->rbct, QSPI_RBCT_RXBRD_USEIPS); 696 697 qspi_write32(priv->flags, ®s->sfar, priv->cur_amba_base); 698 699 qspi_write32(priv->flags, ®s->ipcr, 700 (SEQID_RDSR << QSPI_IPCR_SEQID_SHIFT) | 0); 701 while (qspi_read32(priv->flags, ®s->sr) & QSPI_SR_BUSY_MASK) 702 ; 703 704 while (1) { 705 reg = qspi_read32(priv->flags, ®s->rbsr); 706 if (reg & QSPI_RBSR_RDBFL_MASK) { 707 data = qspi_read32(priv->flags, ®s->rbdr[0]); 708 data = qspi_endian_xchg(data); 709 memcpy(rxbuf, &data, len); 710 qspi_write32(priv->flags, ®s->mcr, 711 qspi_read32(priv->flags, ®s->mcr) | 712 QSPI_MCR_CLR_RXF_MASK); 713 break; 714 } 715 } 716 717 qspi_write32(priv->flags, ®s->mcr, mcr_reg); 718 } 719 720 static void qspi_op_erase(struct fsl_qspi_priv *priv) 721 { 722 struct fsl_qspi_regs *regs = priv->regs; 723 u32 mcr_reg; 724 u32 to_or_from = 0; 725 726 mcr_reg = qspi_read32(priv->flags, ®s->mcr); 727 qspi_write32(priv->flags, ®s->mcr, 728 QSPI_MCR_CLR_RXF_MASK | QSPI_MCR_CLR_TXF_MASK | 729 QSPI_MCR_RESERVED_MASK | QSPI_MCR_END_CFD_LE); 730 qspi_write32(priv->flags, ®s->rbct, QSPI_RBCT_RXBRD_USEIPS); 731 732 to_or_from = priv->sf_addr + priv->cur_amba_base; 733 qspi_write32(priv->flags, ®s->sfar, to_or_from); 734 735 qspi_write32(priv->flags, ®s->ipcr, 736 (SEQID_WREN << QSPI_IPCR_SEQID_SHIFT) | 0); 737 while (qspi_read32(priv->flags, ®s->sr) & QSPI_SR_BUSY_MASK) 738 ; 739 740 if (priv->cur_seqid == QSPI_CMD_SE) { 741 qspi_write32(priv->flags, ®s->ipcr, 742 (SEQID_SE << QSPI_IPCR_SEQID_SHIFT) | 0); 743 } else if (priv->cur_seqid == QSPI_CMD_BE_4K) { 744 qspi_write32(priv->flags, ®s->ipcr, 745 (SEQID_BE_4K << QSPI_IPCR_SEQID_SHIFT) | 0); 746 } 747 while (qspi_read32(priv->flags, ®s->sr) & QSPI_SR_BUSY_MASK) 748 ; 749 750 qspi_write32(priv->flags, ®s->mcr, mcr_reg); 751 } 752 753 int qspi_xfer(struct fsl_qspi_priv *priv, unsigned int bitlen, 754 const void *dout, void *din, unsigned long flags) 755 { 756 u32 bytes = DIV_ROUND_UP(bitlen, 8); 757 static u32 wr_sfaddr; 758 u32 txbuf; 759 760 if (dout) { 761 if (flags & SPI_XFER_BEGIN) { 762 priv->cur_seqid = *(u8 *)dout; 763 memcpy(&txbuf, dout, 4); 764 } 765 766 if (flags == SPI_XFER_END) { 767 priv->sf_addr = wr_sfaddr; 768 qspi_op_write(priv, (u8 *)dout, bytes); 769 return 0; 770 } 771 772 if (priv->cur_seqid == QSPI_CMD_FAST_READ || 773 priv->cur_seqid == QSPI_CMD_RDAR) { 774 priv->sf_addr = swab32(txbuf) & OFFSET_BITS_MASK; 775 } else if ((priv->cur_seqid == QSPI_CMD_SE) || 776 (priv->cur_seqid == QSPI_CMD_BE_4K)) { 777 priv->sf_addr = swab32(txbuf) & OFFSET_BITS_MASK; 778 qspi_op_erase(priv); 779 } else if (priv->cur_seqid == QSPI_CMD_PP || 780 priv->cur_seqid == QSPI_CMD_WRAR) { 781 wr_sfaddr = swab32(txbuf) & OFFSET_BITS_MASK; 782 } else if ((priv->cur_seqid == QSPI_CMD_BRWR) || 783 (priv->cur_seqid == QSPI_CMD_WREAR)) { 784 #ifdef CONFIG_SPI_FLASH_BAR 785 wr_sfaddr = 0; 786 #endif 787 } 788 } 789 790 if (din) { 791 if (priv->cur_seqid == QSPI_CMD_FAST_READ) { 792 #ifdef CONFIG_SYS_FSL_QSPI_AHB 793 qspi_ahb_read(priv, din, bytes); 794 #else 795 qspi_op_read(priv, din, bytes); 796 #endif 797 } else if (priv->cur_seqid == QSPI_CMD_RDAR) { 798 qspi_op_read(priv, din, bytes); 799 } else if (priv->cur_seqid == QSPI_CMD_RDID) 800 qspi_op_rdid(priv, din, bytes); 801 else if (priv->cur_seqid == QSPI_CMD_RDSR) 802 qspi_op_rdsr(priv, din, bytes); 803 #ifdef CONFIG_SPI_FLASH_BAR 804 else if ((priv->cur_seqid == QSPI_CMD_BRRD) || 805 (priv->cur_seqid == QSPI_CMD_RDEAR)) { 806 priv->sf_addr = 0; 807 qspi_op_rdbank(priv, din, bytes); 808 } 809 #endif 810 } 811 812 #ifdef CONFIG_SYS_FSL_QSPI_AHB 813 if ((priv->cur_seqid == QSPI_CMD_SE) || 814 (priv->cur_seqid == QSPI_CMD_PP) || 815 (priv->cur_seqid == QSPI_CMD_BE_4K) || 816 (priv->cur_seqid == QSPI_CMD_WREAR) || 817 (priv->cur_seqid == QSPI_CMD_BRWR)) 818 qspi_ahb_invalid(priv); 819 #endif 820 821 return 0; 822 } 823 824 void qspi_module_disable(struct fsl_qspi_priv *priv, u8 disable) 825 { 826 u32 mcr_val; 827 828 mcr_val = qspi_read32(priv->flags, &priv->regs->mcr); 829 if (disable) 830 mcr_val |= QSPI_MCR_MDIS_MASK; 831 else 832 mcr_val &= ~QSPI_MCR_MDIS_MASK; 833 qspi_write32(priv->flags, &priv->regs->mcr, mcr_val); 834 } 835 836 void qspi_cfg_smpr(struct fsl_qspi_priv *priv, u32 clear_bits, u32 set_bits) 837 { 838 u32 smpr_val; 839 840 smpr_val = qspi_read32(priv->flags, &priv->regs->smpr); 841 smpr_val &= ~clear_bits; 842 smpr_val |= set_bits; 843 qspi_write32(priv->flags, &priv->regs->smpr, smpr_val); 844 } 845 #ifndef CONFIG_DM_SPI 846 static unsigned long spi_bases[] = { 847 QSPI0_BASE_ADDR, 848 #ifdef CONFIG_MX6SX 849 QSPI1_BASE_ADDR, 850 #endif 851 }; 852 853 static unsigned long amba_bases[] = { 854 QSPI0_AMBA_BASE, 855 #ifdef CONFIG_MX6SX 856 QSPI1_AMBA_BASE, 857 #endif 858 }; 859 860 static inline struct fsl_qspi *to_qspi_spi(struct spi_slave *slave) 861 { 862 return container_of(slave, struct fsl_qspi, slave); 863 } 864 865 struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs, 866 unsigned int max_hz, unsigned int mode) 867 { 868 u32 mcr_val; 869 struct fsl_qspi *qspi; 870 struct fsl_qspi_regs *regs; 871 u32 total_size; 872 873 if (bus >= ARRAY_SIZE(spi_bases)) 874 return NULL; 875 876 if (cs >= FSL_QSPI_FLASH_NUM) 877 return NULL; 878 879 qspi = spi_alloc_slave(struct fsl_qspi, bus, cs); 880 if (!qspi) 881 return NULL; 882 883 #ifdef CONFIG_SYS_FSL_QSPI_BE 884 qspi->priv.flags |= QSPI_FLAG_REGMAP_ENDIAN_BIG; 885 #endif 886 887 regs = (struct fsl_qspi_regs *)spi_bases[bus]; 888 qspi->priv.regs = regs; 889 /* 890 * According cs, use different amba_base to choose the 891 * corresponding flash devices. 892 * 893 * If not, only one flash device is used even if passing 894 * different cs using `sf probe` 895 */ 896 qspi->priv.cur_amba_base = amba_bases[bus] + cs * FSL_QSPI_FLASH_SIZE; 897 898 qspi->slave.max_write_size = TX_BUFFER_SIZE; 899 900 mcr_val = qspi_read32(qspi->priv.flags, ®s->mcr); 901 qspi_write32(qspi->priv.flags, ®s->mcr, 902 QSPI_MCR_RESERVED_MASK | QSPI_MCR_MDIS_MASK | 903 (mcr_val & QSPI_MCR_END_CFD_MASK)); 904 905 qspi_cfg_smpr(&qspi->priv, 906 ~(QSPI_SMPR_FSDLY_MASK | QSPI_SMPR_DDRSMP_MASK | 907 QSPI_SMPR_FSPHS_MASK | QSPI_SMPR_HSENA_MASK), 0); 908 909 total_size = FSL_QSPI_FLASH_SIZE * FSL_QSPI_FLASH_NUM; 910 /* 911 * Any read access to non-implemented addresses will provide 912 * undefined results. 913 * 914 * In case single die flash devices, TOP_ADDR_MEMA2 and 915 * TOP_ADDR_MEMB2 should be initialized/programmed to 916 * TOP_ADDR_MEMA1 and TOP_ADDR_MEMB1 respectively - in effect, 917 * setting the size of these devices to 0. This would ensure 918 * that the complete memory map is assigned to only one flash device. 919 */ 920 qspi_write32(qspi->priv.flags, ®s->sfa1ad, 921 FSL_QSPI_FLASH_SIZE | amba_bases[bus]); 922 qspi_write32(qspi->priv.flags, ®s->sfa2ad, 923 FSL_QSPI_FLASH_SIZE | amba_bases[bus]); 924 qspi_write32(qspi->priv.flags, ®s->sfb1ad, 925 total_size | amba_bases[bus]); 926 qspi_write32(qspi->priv.flags, ®s->sfb2ad, 927 total_size | amba_bases[bus]); 928 929 qspi_set_lut(&qspi->priv); 930 931 #ifdef CONFIG_SYS_FSL_QSPI_AHB 932 qspi_init_ahb_read(&qspi->priv); 933 #endif 934 935 qspi_module_disable(&qspi->priv, 0); 936 937 return &qspi->slave; 938 } 939 940 void spi_free_slave(struct spi_slave *slave) 941 { 942 struct fsl_qspi *qspi = to_qspi_spi(slave); 943 944 free(qspi); 945 } 946 947 int spi_claim_bus(struct spi_slave *slave) 948 { 949 return 0; 950 } 951 952 void spi_release_bus(struct spi_slave *slave) 953 { 954 /* Nothing to do */ 955 } 956 957 int spi_xfer(struct spi_slave *slave, unsigned int bitlen, 958 const void *dout, void *din, unsigned long flags) 959 { 960 struct fsl_qspi *qspi = to_qspi_spi(slave); 961 962 return qspi_xfer(&qspi->priv, bitlen, dout, din, flags); 963 } 964 965 void spi_init(void) 966 { 967 /* Nothing to do */ 968 } 969 #else 970 static int fsl_qspi_child_pre_probe(struct udevice *dev) 971 { 972 struct spi_slave *slave = dev_get_parent_priv(dev); 973 974 slave->max_write_size = TX_BUFFER_SIZE; 975 976 return 0; 977 } 978 979 static int fsl_qspi_probe(struct udevice *bus) 980 { 981 u32 mcr_val; 982 u32 amba_size_per_chip; 983 struct fsl_qspi_platdata *plat = dev_get_platdata(bus); 984 struct fsl_qspi_priv *priv = dev_get_priv(bus); 985 struct dm_spi_bus *dm_spi_bus; 986 int i; 987 988 dm_spi_bus = bus->uclass_priv; 989 990 dm_spi_bus->max_hz = plat->speed_hz; 991 992 priv->regs = (struct fsl_qspi_regs *)(uintptr_t)plat->reg_base; 993 priv->flags = plat->flags; 994 995 priv->speed_hz = plat->speed_hz; 996 /* 997 * QSPI SFADR width is 32bits, the max dest addr is 4GB-1. 998 * AMBA memory zone should be located on the 0~4GB space 999 * even on a 64bits cpu. 1000 */ 1001 priv->amba_base[0] = (u32)plat->amba_base; 1002 priv->amba_total_size = (u32)plat->amba_total_size; 1003 priv->flash_num = plat->flash_num; 1004 priv->num_chipselect = plat->num_chipselect; 1005 1006 mcr_val = qspi_read32(priv->flags, &priv->regs->mcr); 1007 qspi_write32(priv->flags, &priv->regs->mcr, 1008 QSPI_MCR_RESERVED_MASK | QSPI_MCR_MDIS_MASK | 1009 (mcr_val & QSPI_MCR_END_CFD_MASK)); 1010 1011 qspi_cfg_smpr(priv, ~(QSPI_SMPR_FSDLY_MASK | QSPI_SMPR_DDRSMP_MASK | 1012 QSPI_SMPR_FSPHS_MASK | QSPI_SMPR_HSENA_MASK), 0); 1013 1014 /* 1015 * Assign AMBA memory zone for every chipselect 1016 * QuadSPI has two channels, every channel has two chipselects. 1017 * If the property 'num-cs' in dts is 2, the AMBA memory will be divided 1018 * into two parts and assign to every channel. This indicate that every 1019 * channel only has one valid chipselect. 1020 * If the property 'num-cs' in dts is 4, the AMBA memory will be divided 1021 * into four parts and assign to every chipselect. 1022 * Every channel will has two valid chipselects. 1023 */ 1024 amba_size_per_chip = priv->amba_total_size >> 1025 (priv->num_chipselect >> 1); 1026 for (i = 1 ; i < priv->num_chipselect ; i++) 1027 priv->amba_base[i] = 1028 amba_size_per_chip + priv->amba_base[i - 1]; 1029 1030 /* 1031 * Any read access to non-implemented addresses will provide 1032 * undefined results. 1033 * 1034 * In case single die flash devices, TOP_ADDR_MEMA2 and 1035 * TOP_ADDR_MEMB2 should be initialized/programmed to 1036 * TOP_ADDR_MEMA1 and TOP_ADDR_MEMB1 respectively - in effect, 1037 * setting the size of these devices to 0. This would ensure 1038 * that the complete memory map is assigned to only one flash device. 1039 */ 1040 qspi_write32(priv->flags, &priv->regs->sfa1ad, priv->amba_base[1]); 1041 switch (priv->num_chipselect) { 1042 case 2: 1043 qspi_write32(priv->flags, &priv->regs->sfa2ad, 1044 priv->amba_base[1]); 1045 qspi_write32(priv->flags, &priv->regs->sfb1ad, 1046 priv->amba_base[1] + amba_size_per_chip); 1047 qspi_write32(priv->flags, &priv->regs->sfb2ad, 1048 priv->amba_base[1] + amba_size_per_chip); 1049 break; 1050 case 4: 1051 qspi_write32(priv->flags, &priv->regs->sfa2ad, 1052 priv->amba_base[2]); 1053 qspi_write32(priv->flags, &priv->regs->sfb1ad, 1054 priv->amba_base[3]); 1055 qspi_write32(priv->flags, &priv->regs->sfb2ad, 1056 priv->amba_base[3] + amba_size_per_chip); 1057 break; 1058 default: 1059 debug("Error: Unsupported chipselect number %u!\n", 1060 priv->num_chipselect); 1061 qspi_module_disable(priv, 1); 1062 return -EINVAL; 1063 } 1064 1065 qspi_set_lut(priv); 1066 1067 #ifdef CONFIG_SYS_FSL_QSPI_AHB 1068 qspi_init_ahb_read(priv); 1069 #endif 1070 1071 qspi_module_disable(priv, 0); 1072 1073 return 0; 1074 } 1075 1076 static int fsl_qspi_ofdata_to_platdata(struct udevice *bus) 1077 { 1078 struct fdt_resource res_regs, res_mem; 1079 struct fsl_qspi_platdata *plat = bus->platdata; 1080 const void *blob = gd->fdt_blob; 1081 int node = bus->of_offset; 1082 int ret, flash_num = 0, subnode; 1083 1084 if (fdtdec_get_bool(blob, node, "big-endian")) 1085 plat->flags |= QSPI_FLAG_REGMAP_ENDIAN_BIG; 1086 1087 ret = fdt_get_named_resource(blob, node, "reg", "reg-names", 1088 "QuadSPI", &res_regs); 1089 if (ret) { 1090 debug("Error: can't get regs base addresses(ret = %d)!\n", ret); 1091 return -ENOMEM; 1092 } 1093 ret = fdt_get_named_resource(blob, node, "reg", "reg-names", 1094 "QuadSPI-memory", &res_mem); 1095 if (ret) { 1096 debug("Error: can't get AMBA base addresses(ret = %d)!\n", ret); 1097 return -ENOMEM; 1098 } 1099 1100 /* Count flash numbers */ 1101 fdt_for_each_subnode(blob, subnode, node) 1102 ++flash_num; 1103 1104 if (flash_num == 0) { 1105 debug("Error: Missing flashes!\n"); 1106 return -ENODEV; 1107 } 1108 1109 plat->speed_hz = fdtdec_get_int(blob, node, "spi-max-frequency", 1110 FSL_QSPI_DEFAULT_SCK_FREQ); 1111 plat->num_chipselect = fdtdec_get_int(blob, node, "num-cs", 1112 FSL_QSPI_MAX_CHIPSELECT_NUM); 1113 1114 plat->reg_base = res_regs.start; 1115 plat->amba_base = res_mem.start; 1116 plat->amba_total_size = res_mem.end - res_mem.start + 1; 1117 plat->flash_num = flash_num; 1118 1119 debug("%s: regs=<0x%llx> <0x%llx, 0x%llx>, max-frequency=%d, endianess=%s\n", 1120 __func__, 1121 (u64)plat->reg_base, 1122 (u64)plat->amba_base, 1123 (u64)plat->amba_total_size, 1124 plat->speed_hz, 1125 plat->flags & QSPI_FLAG_REGMAP_ENDIAN_BIG ? "be" : "le" 1126 ); 1127 1128 return 0; 1129 } 1130 1131 static int fsl_qspi_xfer(struct udevice *dev, unsigned int bitlen, 1132 const void *dout, void *din, unsigned long flags) 1133 { 1134 struct fsl_qspi_priv *priv; 1135 struct udevice *bus; 1136 1137 bus = dev->parent; 1138 priv = dev_get_priv(bus); 1139 1140 return qspi_xfer(priv, bitlen, dout, din, flags); 1141 } 1142 1143 static int fsl_qspi_claim_bus(struct udevice *dev) 1144 { 1145 struct fsl_qspi_priv *priv; 1146 struct udevice *bus; 1147 struct dm_spi_slave_platdata *slave_plat = dev_get_parent_platdata(dev); 1148 1149 bus = dev->parent; 1150 priv = dev_get_priv(bus); 1151 1152 priv->cur_amba_base = priv->amba_base[slave_plat->cs]; 1153 1154 qspi_module_disable(priv, 0); 1155 1156 return 0; 1157 } 1158 1159 static int fsl_qspi_release_bus(struct udevice *dev) 1160 { 1161 struct fsl_qspi_priv *priv; 1162 struct udevice *bus; 1163 1164 bus = dev->parent; 1165 priv = dev_get_priv(bus); 1166 1167 qspi_module_disable(priv, 1); 1168 1169 return 0; 1170 } 1171 1172 static int fsl_qspi_set_speed(struct udevice *bus, uint speed) 1173 { 1174 /* Nothing to do */ 1175 return 0; 1176 } 1177 1178 static int fsl_qspi_set_mode(struct udevice *bus, uint mode) 1179 { 1180 /* Nothing to do */ 1181 return 0; 1182 } 1183 1184 static const struct dm_spi_ops fsl_qspi_ops = { 1185 .claim_bus = fsl_qspi_claim_bus, 1186 .release_bus = fsl_qspi_release_bus, 1187 .xfer = fsl_qspi_xfer, 1188 .set_speed = fsl_qspi_set_speed, 1189 .set_mode = fsl_qspi_set_mode, 1190 }; 1191 1192 static const struct udevice_id fsl_qspi_ids[] = { 1193 { .compatible = "fsl,vf610-qspi" }, 1194 { .compatible = "fsl,imx6sx-qspi" }, 1195 { } 1196 }; 1197 1198 U_BOOT_DRIVER(fsl_qspi) = { 1199 .name = "fsl_qspi", 1200 .id = UCLASS_SPI, 1201 .of_match = fsl_qspi_ids, 1202 .ops = &fsl_qspi_ops, 1203 .ofdata_to_platdata = fsl_qspi_ofdata_to_platdata, 1204 .platdata_auto_alloc_size = sizeof(struct fsl_qspi_platdata), 1205 .priv_auto_alloc_size = sizeof(struct fsl_qspi_priv), 1206 .probe = fsl_qspi_probe, 1207 .child_pre_probe = fsl_qspi_child_pre_probe, 1208 }; 1209 #endif 1210