1 /* 2 * Copyright 2013-2015 Freescale Semiconductor, Inc. 3 * 4 * Freescale Quad Serial Peripheral Interface (QSPI) driver 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #include <common.h> 10 #include <malloc.h> 11 #include <spi.h> 12 #include <asm/io.h> 13 #include <linux/sizes.h> 14 #include <dm.h> 15 #include <errno.h> 16 #include <watchdog.h> 17 #include <wait_bit.h> 18 #include "fsl_qspi.h" 19 20 DECLARE_GLOBAL_DATA_PTR; 21 22 #define RX_BUFFER_SIZE 0x80 23 #if defined(CONFIG_MX6SX) || defined(CONFIG_MX6UL) || \ 24 defined(CONFIG_MX6ULL) || defined(CONFIG_MX7D) 25 #define TX_BUFFER_SIZE 0x200 26 #else 27 #define TX_BUFFER_SIZE 0x40 28 #endif 29 30 #define OFFSET_BITS_MASK GENMASK(23, 0) 31 32 #define FLASH_STATUS_WEL 0x02 33 34 /* SEQID */ 35 #define SEQID_WREN 1 36 #define SEQID_FAST_READ 2 37 #define SEQID_RDSR 3 38 #define SEQID_SE 4 39 #define SEQID_CHIP_ERASE 5 40 #define SEQID_PP 6 41 #define SEQID_RDID 7 42 #define SEQID_BE_4K 8 43 #ifdef CONFIG_SPI_FLASH_BAR 44 #define SEQID_BRRD 9 45 #define SEQID_BRWR 10 46 #define SEQID_RDEAR 11 47 #define SEQID_WREAR 12 48 #endif 49 #define SEQID_WRAR 13 50 #define SEQID_RDAR 14 51 52 /* QSPI CMD */ 53 #define QSPI_CMD_PP 0x02 /* Page program (up to 256 bytes) */ 54 #define QSPI_CMD_RDSR 0x05 /* Read status register */ 55 #define QSPI_CMD_WREN 0x06 /* Write enable */ 56 #define QSPI_CMD_FAST_READ 0x0b /* Read data bytes (high frequency) */ 57 #define QSPI_CMD_BE_4K 0x20 /* 4K erase */ 58 #define QSPI_CMD_CHIP_ERASE 0xc7 /* Erase whole flash chip */ 59 #define QSPI_CMD_SE 0xd8 /* Sector erase (usually 64KiB) */ 60 #define QSPI_CMD_RDID 0x9f /* Read JEDEC ID */ 61 62 /* Used for Micron, winbond and Macronix flashes */ 63 #define QSPI_CMD_WREAR 0xc5 /* EAR register write */ 64 #define QSPI_CMD_RDEAR 0xc8 /* EAR reigster read */ 65 66 /* Used for Spansion flashes only. */ 67 #define QSPI_CMD_BRRD 0x16 /* Bank register read */ 68 #define QSPI_CMD_BRWR 0x17 /* Bank register write */ 69 70 /* Used for Spansion S25FS-S family flash only. */ 71 #define QSPI_CMD_RDAR 0x65 /* Read any device register */ 72 #define QSPI_CMD_WRAR 0x71 /* Write any device register */ 73 74 /* 4-byte address QSPI CMD - used on Spansion and some Macronix flashes */ 75 #define QSPI_CMD_FAST_READ_4B 0x0c /* Read data bytes (high frequency) */ 76 #define QSPI_CMD_PP_4B 0x12 /* Page program (up to 256 bytes) */ 77 #define QSPI_CMD_SE_4B 0xdc /* Sector erase (usually 64KiB) */ 78 79 /* fsl_qspi_platdata flags */ 80 #define QSPI_FLAG_REGMAP_ENDIAN_BIG BIT(0) 81 82 /* default SCK frequency, unit: HZ */ 83 #define FSL_QSPI_DEFAULT_SCK_FREQ 50000000 84 85 /* QSPI max chipselect signals number */ 86 #define FSL_QSPI_MAX_CHIPSELECT_NUM 4 87 88 #ifdef CONFIG_DM_SPI 89 /** 90 * struct fsl_qspi_platdata - platform data for Freescale QSPI 91 * 92 * @flags: Flags for QSPI QSPI_FLAG_... 93 * @speed_hz: Default SCK frequency 94 * @reg_base: Base address of QSPI registers 95 * @amba_base: Base address of QSPI memory mapping 96 * @amba_total_size: size of QSPI memory mapping 97 * @flash_num: Number of active slave devices 98 * @num_chipselect: Number of QSPI chipselect signals 99 */ 100 struct fsl_qspi_platdata { 101 u32 flags; 102 u32 speed_hz; 103 fdt_addr_t reg_base; 104 fdt_addr_t amba_base; 105 fdt_size_t amba_total_size; 106 u32 flash_num; 107 u32 num_chipselect; 108 }; 109 #endif 110 111 /** 112 * struct fsl_qspi_priv - private data for Freescale QSPI 113 * 114 * @flags: Flags for QSPI QSPI_FLAG_... 115 * @bus_clk: QSPI input clk frequency 116 * @speed_hz: Default SCK frequency 117 * @cur_seqid: current LUT table sequence id 118 * @sf_addr: flash access offset 119 * @amba_base: Base address of QSPI memory mapping of every CS 120 * @amba_total_size: size of QSPI memory mapping 121 * @cur_amba_base: Base address of QSPI memory mapping of current CS 122 * @flash_num: Number of active slave devices 123 * @num_chipselect: Number of QSPI chipselect signals 124 * @regs: Point to QSPI register structure for I/O access 125 */ 126 struct fsl_qspi_priv { 127 u32 flags; 128 u32 bus_clk; 129 u32 speed_hz; 130 u32 cur_seqid; 131 u32 sf_addr; 132 u32 amba_base[FSL_QSPI_MAX_CHIPSELECT_NUM]; 133 u32 amba_total_size; 134 u32 cur_amba_base; 135 u32 flash_num; 136 u32 num_chipselect; 137 struct fsl_qspi_regs *regs; 138 }; 139 140 #ifndef CONFIG_DM_SPI 141 struct fsl_qspi { 142 struct spi_slave slave; 143 struct fsl_qspi_priv priv; 144 }; 145 #endif 146 147 static u32 qspi_read32(u32 flags, u32 *addr) 148 { 149 return flags & QSPI_FLAG_REGMAP_ENDIAN_BIG ? 150 in_be32(addr) : in_le32(addr); 151 } 152 153 static void qspi_write32(u32 flags, u32 *addr, u32 val) 154 { 155 flags & QSPI_FLAG_REGMAP_ENDIAN_BIG ? 156 out_be32(addr, val) : out_le32(addr, val); 157 } 158 159 /* QSPI support swapping the flash read/write data 160 * in hardware for LS102xA, but not for VF610 */ 161 static inline u32 qspi_endian_xchg(u32 data) 162 { 163 #ifdef CONFIG_VF610 164 return swab32(data); 165 #else 166 return data; 167 #endif 168 } 169 170 static void qspi_set_lut(struct fsl_qspi_priv *priv) 171 { 172 struct fsl_qspi_regs *regs = priv->regs; 173 u32 lut_base; 174 175 /* Unlock the LUT */ 176 qspi_write32(priv->flags, ®s->lutkey, LUT_KEY_VALUE); 177 qspi_write32(priv->flags, ®s->lckcr, QSPI_LCKCR_UNLOCK); 178 179 /* Write Enable */ 180 lut_base = SEQID_WREN * 4; 181 qspi_write32(priv->flags, ®s->lut[lut_base], OPRND0(QSPI_CMD_WREN) | 182 PAD0(LUT_PAD1) | INSTR0(LUT_CMD)); 183 qspi_write32(priv->flags, ®s->lut[lut_base + 1], 0); 184 qspi_write32(priv->flags, ®s->lut[lut_base + 2], 0); 185 qspi_write32(priv->flags, ®s->lut[lut_base + 3], 0); 186 187 /* Fast Read */ 188 lut_base = SEQID_FAST_READ * 4; 189 #ifdef CONFIG_SPI_FLASH_BAR 190 qspi_write32(priv->flags, ®s->lut[lut_base], 191 OPRND0(QSPI_CMD_FAST_READ) | PAD0(LUT_PAD1) | 192 INSTR0(LUT_CMD) | OPRND1(ADDR24BIT) | 193 PAD1(LUT_PAD1) | INSTR1(LUT_ADDR)); 194 #else 195 if (FSL_QSPI_FLASH_SIZE <= SZ_16M) 196 qspi_write32(priv->flags, ®s->lut[lut_base], 197 OPRND0(QSPI_CMD_FAST_READ) | PAD0(LUT_PAD1) | 198 INSTR0(LUT_CMD) | OPRND1(ADDR24BIT) | 199 PAD1(LUT_PAD1) | INSTR1(LUT_ADDR)); 200 else 201 qspi_write32(priv->flags, ®s->lut[lut_base], 202 OPRND0(QSPI_CMD_FAST_READ_4B) | 203 PAD0(LUT_PAD1) | INSTR0(LUT_CMD) | 204 OPRND1(ADDR32BIT) | PAD1(LUT_PAD1) | 205 INSTR1(LUT_ADDR)); 206 #endif 207 qspi_write32(priv->flags, ®s->lut[lut_base + 1], 208 OPRND0(8) | PAD0(LUT_PAD1) | INSTR0(LUT_DUMMY) | 209 OPRND1(RX_BUFFER_SIZE) | PAD1(LUT_PAD1) | 210 INSTR1(LUT_READ)); 211 qspi_write32(priv->flags, ®s->lut[lut_base + 2], 0); 212 qspi_write32(priv->flags, ®s->lut[lut_base + 3], 0); 213 214 /* Read Status */ 215 lut_base = SEQID_RDSR * 4; 216 qspi_write32(priv->flags, ®s->lut[lut_base], OPRND0(QSPI_CMD_RDSR) | 217 PAD0(LUT_PAD1) | INSTR0(LUT_CMD) | OPRND1(1) | 218 PAD1(LUT_PAD1) | INSTR1(LUT_READ)); 219 qspi_write32(priv->flags, ®s->lut[lut_base + 1], 0); 220 qspi_write32(priv->flags, ®s->lut[lut_base + 2], 0); 221 qspi_write32(priv->flags, ®s->lut[lut_base + 3], 0); 222 223 /* Erase a sector */ 224 lut_base = SEQID_SE * 4; 225 #ifdef CONFIG_SPI_FLASH_BAR 226 qspi_write32(priv->flags, ®s->lut[lut_base], OPRND0(QSPI_CMD_SE) | 227 PAD0(LUT_PAD1) | INSTR0(LUT_CMD) | OPRND1(ADDR24BIT) | 228 PAD1(LUT_PAD1) | INSTR1(LUT_ADDR)); 229 #else 230 if (FSL_QSPI_FLASH_SIZE <= SZ_16M) 231 qspi_write32(priv->flags, ®s->lut[lut_base], 232 OPRND0(QSPI_CMD_SE) | PAD0(LUT_PAD1) | 233 INSTR0(LUT_CMD) | OPRND1(ADDR24BIT) | 234 PAD1(LUT_PAD1) | INSTR1(LUT_ADDR)); 235 else 236 qspi_write32(priv->flags, ®s->lut[lut_base], 237 OPRND0(QSPI_CMD_SE_4B) | PAD0(LUT_PAD1) | 238 INSTR0(LUT_CMD) | OPRND1(ADDR32BIT) | 239 PAD1(LUT_PAD1) | INSTR1(LUT_ADDR)); 240 #endif 241 qspi_write32(priv->flags, ®s->lut[lut_base + 1], 0); 242 qspi_write32(priv->flags, ®s->lut[lut_base + 2], 0); 243 qspi_write32(priv->flags, ®s->lut[lut_base + 3], 0); 244 245 /* Erase the whole chip */ 246 lut_base = SEQID_CHIP_ERASE * 4; 247 qspi_write32(priv->flags, ®s->lut[lut_base], 248 OPRND0(QSPI_CMD_CHIP_ERASE) | 249 PAD0(LUT_PAD1) | INSTR0(LUT_CMD)); 250 qspi_write32(priv->flags, ®s->lut[lut_base + 1], 0); 251 qspi_write32(priv->flags, ®s->lut[lut_base + 2], 0); 252 qspi_write32(priv->flags, ®s->lut[lut_base + 3], 0); 253 254 /* Page Program */ 255 lut_base = SEQID_PP * 4; 256 #ifdef CONFIG_SPI_FLASH_BAR 257 qspi_write32(priv->flags, ®s->lut[lut_base], OPRND0(QSPI_CMD_PP) | 258 PAD0(LUT_PAD1) | INSTR0(LUT_CMD) | OPRND1(ADDR24BIT) | 259 PAD1(LUT_PAD1) | INSTR1(LUT_ADDR)); 260 #else 261 if (FSL_QSPI_FLASH_SIZE <= SZ_16M) 262 qspi_write32(priv->flags, ®s->lut[lut_base], 263 OPRND0(QSPI_CMD_PP) | PAD0(LUT_PAD1) | 264 INSTR0(LUT_CMD) | OPRND1(ADDR24BIT) | 265 PAD1(LUT_PAD1) | INSTR1(LUT_ADDR)); 266 else 267 qspi_write32(priv->flags, ®s->lut[lut_base], 268 OPRND0(QSPI_CMD_PP_4B) | PAD0(LUT_PAD1) | 269 INSTR0(LUT_CMD) | OPRND1(ADDR32BIT) | 270 PAD1(LUT_PAD1) | INSTR1(LUT_ADDR)); 271 #endif 272 #if defined(CONFIG_MX6SX) || defined(CONFIG_MX6UL) || \ 273 defined(CONFIG_MX6ULL) || defined(CONFIG_MX7D) 274 /* 275 * To MX6SX, OPRND0(TX_BUFFER_SIZE) can not work correctly. 276 * So, Use IDATSZ in IPCR to determine the size and here set 0. 277 */ 278 qspi_write32(priv->flags, ®s->lut[lut_base + 1], OPRND0(0) | 279 PAD0(LUT_PAD1) | INSTR0(LUT_WRITE)); 280 #else 281 qspi_write32(priv->flags, ®s->lut[lut_base + 1], 282 OPRND0(TX_BUFFER_SIZE) | 283 PAD0(LUT_PAD1) | INSTR0(LUT_WRITE)); 284 #endif 285 qspi_write32(priv->flags, ®s->lut[lut_base + 2], 0); 286 qspi_write32(priv->flags, ®s->lut[lut_base + 3], 0); 287 288 /* READ ID */ 289 lut_base = SEQID_RDID * 4; 290 qspi_write32(priv->flags, ®s->lut[lut_base], OPRND0(QSPI_CMD_RDID) | 291 PAD0(LUT_PAD1) | INSTR0(LUT_CMD) | OPRND1(8) | 292 PAD1(LUT_PAD1) | INSTR1(LUT_READ)); 293 qspi_write32(priv->flags, ®s->lut[lut_base + 1], 0); 294 qspi_write32(priv->flags, ®s->lut[lut_base + 2], 0); 295 qspi_write32(priv->flags, ®s->lut[lut_base + 3], 0); 296 297 /* SUB SECTOR 4K ERASE */ 298 lut_base = SEQID_BE_4K * 4; 299 qspi_write32(priv->flags, ®s->lut[lut_base], OPRND0(QSPI_CMD_BE_4K) | 300 PAD0(LUT_PAD1) | INSTR0(LUT_CMD) | OPRND1(ADDR24BIT) | 301 PAD1(LUT_PAD1) | INSTR1(LUT_ADDR)); 302 303 #ifdef CONFIG_SPI_FLASH_BAR 304 /* 305 * BRRD BRWR RDEAR WREAR are all supported, because it is hard to 306 * dynamically check whether to set BRRD BRWR or RDEAR WREAR during 307 * initialization. 308 */ 309 lut_base = SEQID_BRRD * 4; 310 qspi_write32(priv->flags, ®s->lut[lut_base], OPRND0(QSPI_CMD_BRRD) | 311 PAD0(LUT_PAD1) | INSTR0(LUT_CMD) | OPRND1(1) | 312 PAD1(LUT_PAD1) | INSTR1(LUT_READ)); 313 314 lut_base = SEQID_BRWR * 4; 315 qspi_write32(priv->flags, ®s->lut[lut_base], OPRND0(QSPI_CMD_BRWR) | 316 PAD0(LUT_PAD1) | INSTR0(LUT_CMD) | OPRND1(1) | 317 PAD1(LUT_PAD1) | INSTR1(LUT_WRITE)); 318 319 lut_base = SEQID_RDEAR * 4; 320 qspi_write32(priv->flags, ®s->lut[lut_base], OPRND0(QSPI_CMD_RDEAR) | 321 PAD0(LUT_PAD1) | INSTR0(LUT_CMD) | OPRND1(1) | 322 PAD1(LUT_PAD1) | INSTR1(LUT_READ)); 323 324 lut_base = SEQID_WREAR * 4; 325 qspi_write32(priv->flags, ®s->lut[lut_base], OPRND0(QSPI_CMD_WREAR) | 326 PAD0(LUT_PAD1) | INSTR0(LUT_CMD) | OPRND1(1) | 327 PAD1(LUT_PAD1) | INSTR1(LUT_WRITE)); 328 #endif 329 330 /* 331 * Read any device register. 332 * Used for Spansion S25FS-S family flash only. 333 */ 334 lut_base = SEQID_RDAR * 4; 335 qspi_write32(priv->flags, ®s->lut[lut_base], 336 OPRND0(QSPI_CMD_RDAR) | PAD0(LUT_PAD1) | 337 INSTR0(LUT_CMD) | OPRND1(ADDR24BIT) | 338 PAD1(LUT_PAD1) | INSTR1(LUT_ADDR)); 339 qspi_write32(priv->flags, ®s->lut[lut_base + 1], 340 OPRND0(8) | PAD0(LUT_PAD1) | INSTR0(LUT_DUMMY) | 341 OPRND1(1) | PAD1(LUT_PAD1) | 342 INSTR1(LUT_READ)); 343 344 /* 345 * Write any device register. 346 * Used for Spansion S25FS-S family flash only. 347 */ 348 lut_base = SEQID_WRAR * 4; 349 qspi_write32(priv->flags, ®s->lut[lut_base], 350 OPRND0(QSPI_CMD_WRAR) | PAD0(LUT_PAD1) | 351 INSTR0(LUT_CMD) | OPRND1(ADDR24BIT) | 352 PAD1(LUT_PAD1) | INSTR1(LUT_ADDR)); 353 qspi_write32(priv->flags, ®s->lut[lut_base + 1], 354 OPRND0(1) | PAD0(LUT_PAD1) | INSTR0(LUT_WRITE)); 355 356 /* Lock the LUT */ 357 qspi_write32(priv->flags, ®s->lutkey, LUT_KEY_VALUE); 358 qspi_write32(priv->flags, ®s->lckcr, QSPI_LCKCR_LOCK); 359 } 360 361 #if defined(CONFIG_SYS_FSL_QSPI_AHB) 362 /* 363 * If we have changed the content of the flash by writing or erasing, 364 * we need to invalidate the AHB buffer. If we do not do so, we may read out 365 * the wrong data. The spec tells us reset the AHB domain and Serial Flash 366 * domain at the same time. 367 */ 368 static inline void qspi_ahb_invalid(struct fsl_qspi_priv *priv) 369 { 370 struct fsl_qspi_regs *regs = priv->regs; 371 u32 reg; 372 373 reg = qspi_read32(priv->flags, ®s->mcr); 374 reg |= QSPI_MCR_SWRSTHD_MASK | QSPI_MCR_SWRSTSD_MASK; 375 qspi_write32(priv->flags, ®s->mcr, reg); 376 377 /* 378 * The minimum delay : 1 AHB + 2 SFCK clocks. 379 * Delay 1 us is enough. 380 */ 381 udelay(1); 382 383 reg &= ~(QSPI_MCR_SWRSTHD_MASK | QSPI_MCR_SWRSTSD_MASK); 384 qspi_write32(priv->flags, ®s->mcr, reg); 385 } 386 387 /* Read out the data from the AHB buffer. */ 388 static inline void qspi_ahb_read(struct fsl_qspi_priv *priv, u8 *rxbuf, int len) 389 { 390 struct fsl_qspi_regs *regs = priv->regs; 391 u32 mcr_reg; 392 void *rx_addr = NULL; 393 394 mcr_reg = qspi_read32(priv->flags, ®s->mcr); 395 396 qspi_write32(priv->flags, ®s->mcr, 397 QSPI_MCR_CLR_RXF_MASK | QSPI_MCR_CLR_TXF_MASK | 398 QSPI_MCR_RESERVED_MASK | QSPI_MCR_END_CFD_LE); 399 400 rx_addr = (void *)(uintptr_t)(priv->cur_amba_base + priv->sf_addr); 401 /* Read out the data directly from the AHB buffer. */ 402 memcpy(rxbuf, rx_addr, len); 403 404 qspi_write32(priv->flags, ®s->mcr, mcr_reg); 405 } 406 407 static void qspi_enable_ddr_mode(struct fsl_qspi_priv *priv) 408 { 409 u32 reg, reg2; 410 struct fsl_qspi_regs *regs = priv->regs; 411 412 reg = qspi_read32(priv->flags, ®s->mcr); 413 /* Disable the module */ 414 qspi_write32(priv->flags, ®s->mcr, reg | QSPI_MCR_MDIS_MASK); 415 416 /* Set the Sampling Register for DDR */ 417 reg2 = qspi_read32(priv->flags, ®s->smpr); 418 reg2 &= ~QSPI_SMPR_DDRSMP_MASK; 419 reg2 |= (2 << QSPI_SMPR_DDRSMP_SHIFT); 420 qspi_write32(priv->flags, ®s->smpr, reg2); 421 422 /* Enable the module again (enable the DDR too) */ 423 reg |= QSPI_MCR_DDR_EN_MASK; 424 /* Enable bit 29 for imx6sx */ 425 reg |= BIT(29); 426 427 qspi_write32(priv->flags, ®s->mcr, reg); 428 } 429 430 /* 431 * There are two different ways to read out the data from the flash: 432 * the "IP Command Read" and the "AHB Command Read". 433 * 434 * The IC guy suggests we use the "AHB Command Read" which is faster 435 * then the "IP Command Read". (What's more is that there is a bug in 436 * the "IP Command Read" in the Vybrid.) 437 * 438 * After we set up the registers for the "AHB Command Read", we can use 439 * the memcpy to read the data directly. A "missed" access to the buffer 440 * causes the controller to clear the buffer, and use the sequence pointed 441 * by the QUADSPI_BFGENCR[SEQID] to initiate a read from the flash. 442 */ 443 static void qspi_init_ahb_read(struct fsl_qspi_priv *priv) 444 { 445 struct fsl_qspi_regs *regs = priv->regs; 446 447 /* AHB configuration for access buffer 0/1/2 .*/ 448 qspi_write32(priv->flags, ®s->buf0cr, QSPI_BUFXCR_INVALID_MSTRID); 449 qspi_write32(priv->flags, ®s->buf1cr, QSPI_BUFXCR_INVALID_MSTRID); 450 qspi_write32(priv->flags, ®s->buf2cr, QSPI_BUFXCR_INVALID_MSTRID); 451 qspi_write32(priv->flags, ®s->buf3cr, QSPI_BUF3CR_ALLMST_MASK | 452 (0x80 << QSPI_BUF3CR_ADATSZ_SHIFT)); 453 454 /* We only use the buffer3 */ 455 qspi_write32(priv->flags, ®s->buf0ind, 0); 456 qspi_write32(priv->flags, ®s->buf1ind, 0); 457 qspi_write32(priv->flags, ®s->buf2ind, 0); 458 459 /* 460 * Set the default lut sequence for AHB Read. 461 * Parallel mode is disabled. 462 */ 463 qspi_write32(priv->flags, ®s->bfgencr, 464 SEQID_FAST_READ << QSPI_BFGENCR_SEQID_SHIFT); 465 466 /*Enable DDR Mode*/ 467 qspi_enable_ddr_mode(priv); 468 } 469 #endif 470 471 #ifdef CONFIG_SPI_FLASH_BAR 472 /* Bank register read/write, EAR register read/write */ 473 static void qspi_op_rdbank(struct fsl_qspi_priv *priv, u8 *rxbuf, u32 len) 474 { 475 struct fsl_qspi_regs *regs = priv->regs; 476 u32 reg, mcr_reg, data, seqid; 477 478 mcr_reg = qspi_read32(priv->flags, ®s->mcr); 479 qspi_write32(priv->flags, ®s->mcr, 480 QSPI_MCR_CLR_RXF_MASK | QSPI_MCR_CLR_TXF_MASK | 481 QSPI_MCR_RESERVED_MASK | QSPI_MCR_END_CFD_LE); 482 qspi_write32(priv->flags, ®s->rbct, QSPI_RBCT_RXBRD_USEIPS); 483 484 qspi_write32(priv->flags, ®s->sfar, priv->cur_amba_base); 485 486 if (priv->cur_seqid == QSPI_CMD_BRRD) 487 seqid = SEQID_BRRD; 488 else 489 seqid = SEQID_RDEAR; 490 491 qspi_write32(priv->flags, ®s->ipcr, 492 (seqid << QSPI_IPCR_SEQID_SHIFT) | len); 493 494 /* Wait previous command complete */ 495 while (qspi_read32(priv->flags, ®s->sr) & QSPI_SR_BUSY_MASK) 496 ; 497 498 while (1) { 499 WATCHDOG_RESET(); 500 501 reg = qspi_read32(priv->flags, ®s->rbsr); 502 if (reg & QSPI_RBSR_RDBFL_MASK) { 503 data = qspi_read32(priv->flags, ®s->rbdr[0]); 504 data = qspi_endian_xchg(data); 505 memcpy(rxbuf, &data, len); 506 qspi_write32(priv->flags, ®s->mcr, 507 qspi_read32(priv->flags, ®s->mcr) | 508 QSPI_MCR_CLR_RXF_MASK); 509 break; 510 } 511 } 512 513 qspi_write32(priv->flags, ®s->mcr, mcr_reg); 514 } 515 #endif 516 517 static void qspi_op_rdid(struct fsl_qspi_priv *priv, u32 *rxbuf, u32 len) 518 { 519 struct fsl_qspi_regs *regs = priv->regs; 520 u32 mcr_reg, rbsr_reg, data, size; 521 int i; 522 523 mcr_reg = qspi_read32(priv->flags, ®s->mcr); 524 qspi_write32(priv->flags, ®s->mcr, 525 QSPI_MCR_CLR_RXF_MASK | QSPI_MCR_CLR_TXF_MASK | 526 QSPI_MCR_RESERVED_MASK | QSPI_MCR_END_CFD_LE); 527 qspi_write32(priv->flags, ®s->rbct, QSPI_RBCT_RXBRD_USEIPS); 528 529 qspi_write32(priv->flags, ®s->sfar, priv->cur_amba_base); 530 531 qspi_write32(priv->flags, ®s->ipcr, 532 (SEQID_RDID << QSPI_IPCR_SEQID_SHIFT) | 0); 533 while (qspi_read32(priv->flags, ®s->sr) & QSPI_SR_BUSY_MASK) 534 ; 535 536 i = 0; 537 while ((RX_BUFFER_SIZE >= len) && (len > 0)) { 538 WATCHDOG_RESET(); 539 540 rbsr_reg = qspi_read32(priv->flags, ®s->rbsr); 541 if (rbsr_reg & QSPI_RBSR_RDBFL_MASK) { 542 data = qspi_read32(priv->flags, ®s->rbdr[i]); 543 data = qspi_endian_xchg(data); 544 size = (len < 4) ? len : 4; 545 memcpy(rxbuf, &data, size); 546 len -= size; 547 rxbuf++; 548 i++; 549 } 550 } 551 552 qspi_write32(priv->flags, ®s->mcr, mcr_reg); 553 } 554 555 /* If not use AHB read, read data from ip interface */ 556 static void qspi_op_read(struct fsl_qspi_priv *priv, u32 *rxbuf, u32 len) 557 { 558 struct fsl_qspi_regs *regs = priv->regs; 559 u32 mcr_reg, data; 560 int i, size; 561 u32 to_or_from; 562 u32 seqid; 563 564 if (priv->cur_seqid == QSPI_CMD_RDAR) 565 seqid = SEQID_RDAR; 566 else 567 seqid = SEQID_FAST_READ; 568 569 mcr_reg = qspi_read32(priv->flags, ®s->mcr); 570 qspi_write32(priv->flags, ®s->mcr, 571 QSPI_MCR_CLR_RXF_MASK | QSPI_MCR_CLR_TXF_MASK | 572 QSPI_MCR_RESERVED_MASK | QSPI_MCR_END_CFD_LE); 573 qspi_write32(priv->flags, ®s->rbct, QSPI_RBCT_RXBRD_USEIPS); 574 575 to_or_from = priv->sf_addr + priv->cur_amba_base; 576 577 while (len > 0) { 578 WATCHDOG_RESET(); 579 580 qspi_write32(priv->flags, ®s->sfar, to_or_from); 581 582 size = (len > RX_BUFFER_SIZE) ? 583 RX_BUFFER_SIZE : len; 584 585 qspi_write32(priv->flags, ®s->ipcr, 586 (seqid << QSPI_IPCR_SEQID_SHIFT) | 587 size); 588 while (qspi_read32(priv->flags, ®s->sr) & QSPI_SR_BUSY_MASK) 589 ; 590 591 to_or_from += size; 592 len -= size; 593 594 i = 0; 595 while ((RX_BUFFER_SIZE >= size) && (size > 0)) { 596 data = qspi_read32(priv->flags, ®s->rbdr[i]); 597 data = qspi_endian_xchg(data); 598 if (size < 4) 599 memcpy(rxbuf, &data, size); 600 else 601 memcpy(rxbuf, &data, 4); 602 rxbuf++; 603 size -= 4; 604 i++; 605 } 606 qspi_write32(priv->flags, ®s->mcr, 607 qspi_read32(priv->flags, ®s->mcr) | 608 QSPI_MCR_CLR_RXF_MASK); 609 } 610 611 qspi_write32(priv->flags, ®s->mcr, mcr_reg); 612 } 613 614 static void qspi_op_write(struct fsl_qspi_priv *priv, u8 *txbuf, u32 len) 615 { 616 struct fsl_qspi_regs *regs = priv->regs; 617 u32 mcr_reg, data, reg, status_reg, seqid; 618 int i, size, tx_size; 619 u32 to_or_from = 0; 620 621 mcr_reg = qspi_read32(priv->flags, ®s->mcr); 622 qspi_write32(priv->flags, ®s->mcr, 623 QSPI_MCR_CLR_RXF_MASK | QSPI_MCR_CLR_TXF_MASK | 624 QSPI_MCR_RESERVED_MASK | QSPI_MCR_END_CFD_LE); 625 qspi_write32(priv->flags, ®s->rbct, QSPI_RBCT_RXBRD_USEIPS); 626 627 status_reg = 0; 628 while ((status_reg & FLASH_STATUS_WEL) != FLASH_STATUS_WEL) { 629 WATCHDOG_RESET(); 630 631 qspi_write32(priv->flags, ®s->ipcr, 632 (SEQID_WREN << QSPI_IPCR_SEQID_SHIFT) | 0); 633 while (qspi_read32(priv->flags, ®s->sr) & QSPI_SR_BUSY_MASK) 634 ; 635 636 qspi_write32(priv->flags, ®s->ipcr, 637 (SEQID_RDSR << QSPI_IPCR_SEQID_SHIFT) | 1); 638 while (qspi_read32(priv->flags, ®s->sr) & QSPI_SR_BUSY_MASK) 639 ; 640 641 reg = qspi_read32(priv->flags, ®s->rbsr); 642 if (reg & QSPI_RBSR_RDBFL_MASK) { 643 status_reg = qspi_read32(priv->flags, ®s->rbdr[0]); 644 status_reg = qspi_endian_xchg(status_reg); 645 } 646 qspi_write32(priv->flags, ®s->mcr, 647 qspi_read32(priv->flags, ®s->mcr) | 648 QSPI_MCR_CLR_RXF_MASK); 649 } 650 651 /* Default is page programming */ 652 seqid = SEQID_PP; 653 if (priv->cur_seqid == QSPI_CMD_WRAR) 654 seqid = SEQID_WRAR; 655 #ifdef CONFIG_SPI_FLASH_BAR 656 if (priv->cur_seqid == QSPI_CMD_BRWR) 657 seqid = SEQID_BRWR; 658 else if (priv->cur_seqid == QSPI_CMD_WREAR) 659 seqid = SEQID_WREAR; 660 #endif 661 662 to_or_from = priv->sf_addr + priv->cur_amba_base; 663 664 qspi_write32(priv->flags, ®s->sfar, to_or_from); 665 666 tx_size = (len > TX_BUFFER_SIZE) ? 667 TX_BUFFER_SIZE : len; 668 669 size = tx_size / 16; 670 /* 671 * There must be atleast 128bit data 672 * available in TX FIFO for any pop operation 673 */ 674 if (tx_size % 16) 675 size++; 676 for (i = 0; i < size * 4; i++) { 677 memcpy(&data, txbuf, 4); 678 data = qspi_endian_xchg(data); 679 qspi_write32(priv->flags, ®s->tbdr, data); 680 txbuf += 4; 681 } 682 683 qspi_write32(priv->flags, ®s->ipcr, 684 (seqid << QSPI_IPCR_SEQID_SHIFT) | tx_size); 685 while (qspi_read32(priv->flags, ®s->sr) & QSPI_SR_BUSY_MASK) 686 ; 687 688 qspi_write32(priv->flags, ®s->mcr, mcr_reg); 689 } 690 691 static void qspi_op_rdsr(struct fsl_qspi_priv *priv, void *rxbuf, u32 len) 692 { 693 struct fsl_qspi_regs *regs = priv->regs; 694 u32 mcr_reg, reg, data; 695 696 mcr_reg = qspi_read32(priv->flags, ®s->mcr); 697 qspi_write32(priv->flags, ®s->mcr, 698 QSPI_MCR_CLR_RXF_MASK | QSPI_MCR_CLR_TXF_MASK | 699 QSPI_MCR_RESERVED_MASK | QSPI_MCR_END_CFD_LE); 700 qspi_write32(priv->flags, ®s->rbct, QSPI_RBCT_RXBRD_USEIPS); 701 702 qspi_write32(priv->flags, ®s->sfar, priv->cur_amba_base); 703 704 qspi_write32(priv->flags, ®s->ipcr, 705 (SEQID_RDSR << QSPI_IPCR_SEQID_SHIFT) | 0); 706 while (qspi_read32(priv->flags, ®s->sr) & QSPI_SR_BUSY_MASK) 707 ; 708 709 while (1) { 710 WATCHDOG_RESET(); 711 712 reg = qspi_read32(priv->flags, ®s->rbsr); 713 if (reg & QSPI_RBSR_RDBFL_MASK) { 714 data = qspi_read32(priv->flags, ®s->rbdr[0]); 715 data = qspi_endian_xchg(data); 716 memcpy(rxbuf, &data, len); 717 qspi_write32(priv->flags, ®s->mcr, 718 qspi_read32(priv->flags, ®s->mcr) | 719 QSPI_MCR_CLR_RXF_MASK); 720 break; 721 } 722 } 723 724 qspi_write32(priv->flags, ®s->mcr, mcr_reg); 725 } 726 727 static void qspi_op_erase(struct fsl_qspi_priv *priv) 728 { 729 struct fsl_qspi_regs *regs = priv->regs; 730 u32 mcr_reg; 731 u32 to_or_from = 0; 732 733 mcr_reg = qspi_read32(priv->flags, ®s->mcr); 734 qspi_write32(priv->flags, ®s->mcr, 735 QSPI_MCR_CLR_RXF_MASK | QSPI_MCR_CLR_TXF_MASK | 736 QSPI_MCR_RESERVED_MASK | QSPI_MCR_END_CFD_LE); 737 qspi_write32(priv->flags, ®s->rbct, QSPI_RBCT_RXBRD_USEIPS); 738 739 to_or_from = priv->sf_addr + priv->cur_amba_base; 740 qspi_write32(priv->flags, ®s->sfar, to_or_from); 741 742 qspi_write32(priv->flags, ®s->ipcr, 743 (SEQID_WREN << QSPI_IPCR_SEQID_SHIFT) | 0); 744 while (qspi_read32(priv->flags, ®s->sr) & QSPI_SR_BUSY_MASK) 745 ; 746 747 if (priv->cur_seqid == QSPI_CMD_SE) { 748 qspi_write32(priv->flags, ®s->ipcr, 749 (SEQID_SE << QSPI_IPCR_SEQID_SHIFT) | 0); 750 } else if (priv->cur_seqid == QSPI_CMD_BE_4K) { 751 qspi_write32(priv->flags, ®s->ipcr, 752 (SEQID_BE_4K << QSPI_IPCR_SEQID_SHIFT) | 0); 753 } 754 while (qspi_read32(priv->flags, ®s->sr) & QSPI_SR_BUSY_MASK) 755 ; 756 757 qspi_write32(priv->flags, ®s->mcr, mcr_reg); 758 } 759 760 int qspi_xfer(struct fsl_qspi_priv *priv, unsigned int bitlen, 761 const void *dout, void *din, unsigned long flags) 762 { 763 u32 bytes = DIV_ROUND_UP(bitlen, 8); 764 static u32 wr_sfaddr; 765 u32 txbuf; 766 767 WATCHDOG_RESET(); 768 769 if (dout) { 770 if (flags & SPI_XFER_BEGIN) { 771 priv->cur_seqid = *(u8 *)dout; 772 memcpy(&txbuf, dout, 4); 773 } 774 775 if (flags == SPI_XFER_END) { 776 priv->sf_addr = wr_sfaddr; 777 qspi_op_write(priv, (u8 *)dout, bytes); 778 return 0; 779 } 780 781 if (priv->cur_seqid == QSPI_CMD_FAST_READ || 782 priv->cur_seqid == QSPI_CMD_RDAR) { 783 priv->sf_addr = swab32(txbuf) & OFFSET_BITS_MASK; 784 } else if ((priv->cur_seqid == QSPI_CMD_SE) || 785 (priv->cur_seqid == QSPI_CMD_BE_4K)) { 786 priv->sf_addr = swab32(txbuf) & OFFSET_BITS_MASK; 787 qspi_op_erase(priv); 788 } else if (priv->cur_seqid == QSPI_CMD_PP || 789 priv->cur_seqid == QSPI_CMD_WRAR) { 790 wr_sfaddr = swab32(txbuf) & OFFSET_BITS_MASK; 791 } else if ((priv->cur_seqid == QSPI_CMD_BRWR) || 792 (priv->cur_seqid == QSPI_CMD_WREAR)) { 793 #ifdef CONFIG_SPI_FLASH_BAR 794 wr_sfaddr = 0; 795 #endif 796 } 797 } 798 799 if (din) { 800 if (priv->cur_seqid == QSPI_CMD_FAST_READ) { 801 #ifdef CONFIG_SYS_FSL_QSPI_AHB 802 qspi_ahb_read(priv, din, bytes); 803 #else 804 qspi_op_read(priv, din, bytes); 805 #endif 806 } else if (priv->cur_seqid == QSPI_CMD_RDAR) { 807 qspi_op_read(priv, din, bytes); 808 } else if (priv->cur_seqid == QSPI_CMD_RDID) 809 qspi_op_rdid(priv, din, bytes); 810 else if (priv->cur_seqid == QSPI_CMD_RDSR) 811 qspi_op_rdsr(priv, din, bytes); 812 #ifdef CONFIG_SPI_FLASH_BAR 813 else if ((priv->cur_seqid == QSPI_CMD_BRRD) || 814 (priv->cur_seqid == QSPI_CMD_RDEAR)) { 815 priv->sf_addr = 0; 816 qspi_op_rdbank(priv, din, bytes); 817 } 818 #endif 819 } 820 821 #ifdef CONFIG_SYS_FSL_QSPI_AHB 822 if ((priv->cur_seqid == QSPI_CMD_SE) || 823 (priv->cur_seqid == QSPI_CMD_PP) || 824 (priv->cur_seqid == QSPI_CMD_BE_4K) || 825 (priv->cur_seqid == QSPI_CMD_WREAR) || 826 (priv->cur_seqid == QSPI_CMD_BRWR)) 827 qspi_ahb_invalid(priv); 828 #endif 829 830 return 0; 831 } 832 833 void qspi_module_disable(struct fsl_qspi_priv *priv, u8 disable) 834 { 835 u32 mcr_val; 836 837 mcr_val = qspi_read32(priv->flags, &priv->regs->mcr); 838 if (disable) 839 mcr_val |= QSPI_MCR_MDIS_MASK; 840 else 841 mcr_val &= ~QSPI_MCR_MDIS_MASK; 842 qspi_write32(priv->flags, &priv->regs->mcr, mcr_val); 843 } 844 845 void qspi_cfg_smpr(struct fsl_qspi_priv *priv, u32 clear_bits, u32 set_bits) 846 { 847 u32 smpr_val; 848 849 smpr_val = qspi_read32(priv->flags, &priv->regs->smpr); 850 smpr_val &= ~clear_bits; 851 smpr_val |= set_bits; 852 qspi_write32(priv->flags, &priv->regs->smpr, smpr_val); 853 } 854 #ifndef CONFIG_DM_SPI 855 static unsigned long spi_bases[] = { 856 QSPI0_BASE_ADDR, 857 #ifdef CONFIG_MX6SX 858 QSPI1_BASE_ADDR, 859 #endif 860 }; 861 862 static unsigned long amba_bases[] = { 863 QSPI0_AMBA_BASE, 864 #ifdef CONFIG_MX6SX 865 QSPI1_AMBA_BASE, 866 #endif 867 }; 868 869 static inline struct fsl_qspi *to_qspi_spi(struct spi_slave *slave) 870 { 871 return container_of(slave, struct fsl_qspi, slave); 872 } 873 874 struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs, 875 unsigned int max_hz, unsigned int mode) 876 { 877 u32 mcr_val; 878 struct fsl_qspi *qspi; 879 struct fsl_qspi_regs *regs; 880 u32 total_size; 881 882 if (bus >= ARRAY_SIZE(spi_bases)) 883 return NULL; 884 885 if (cs >= FSL_QSPI_FLASH_NUM) 886 return NULL; 887 888 qspi = spi_alloc_slave(struct fsl_qspi, bus, cs); 889 if (!qspi) 890 return NULL; 891 892 #ifdef CONFIG_SYS_FSL_QSPI_BE 893 qspi->priv.flags |= QSPI_FLAG_REGMAP_ENDIAN_BIG; 894 #endif 895 896 regs = (struct fsl_qspi_regs *)spi_bases[bus]; 897 qspi->priv.regs = regs; 898 /* 899 * According cs, use different amba_base to choose the 900 * corresponding flash devices. 901 * 902 * If not, only one flash device is used even if passing 903 * different cs using `sf probe` 904 */ 905 qspi->priv.cur_amba_base = amba_bases[bus] + cs * FSL_QSPI_FLASH_SIZE; 906 907 qspi->slave.max_write_size = TX_BUFFER_SIZE; 908 909 mcr_val = qspi_read32(qspi->priv.flags, ®s->mcr); 910 911 /* Set endianness to LE for i.mx */ 912 if (IS_ENABLED(CONFIG_MX6) || IS_ENABLED(CONFIG_MX7)) 913 mcr_val = QSPI_MCR_END_CFD_LE; 914 915 qspi_write32(qspi->priv.flags, ®s->mcr, 916 QSPI_MCR_RESERVED_MASK | QSPI_MCR_MDIS_MASK | 917 (mcr_val & QSPI_MCR_END_CFD_MASK)); 918 919 qspi_cfg_smpr(&qspi->priv, 920 ~(QSPI_SMPR_FSDLY_MASK | QSPI_SMPR_DDRSMP_MASK | 921 QSPI_SMPR_FSPHS_MASK | QSPI_SMPR_HSENA_MASK), 0); 922 923 total_size = FSL_QSPI_FLASH_SIZE * FSL_QSPI_FLASH_NUM; 924 /* 925 * Any read access to non-implemented addresses will provide 926 * undefined results. 927 * 928 * In case single die flash devices, TOP_ADDR_MEMA2 and 929 * TOP_ADDR_MEMB2 should be initialized/programmed to 930 * TOP_ADDR_MEMA1 and TOP_ADDR_MEMB1 respectively - in effect, 931 * setting the size of these devices to 0. This would ensure 932 * that the complete memory map is assigned to only one flash device. 933 */ 934 qspi_write32(qspi->priv.flags, ®s->sfa1ad, 935 FSL_QSPI_FLASH_SIZE | amba_bases[bus]); 936 qspi_write32(qspi->priv.flags, ®s->sfa2ad, 937 FSL_QSPI_FLASH_SIZE | amba_bases[bus]); 938 qspi_write32(qspi->priv.flags, ®s->sfb1ad, 939 total_size | amba_bases[bus]); 940 qspi_write32(qspi->priv.flags, ®s->sfb2ad, 941 total_size | amba_bases[bus]); 942 943 qspi_set_lut(&qspi->priv); 944 945 #ifdef CONFIG_SYS_FSL_QSPI_AHB 946 qspi_init_ahb_read(&qspi->priv); 947 #endif 948 949 qspi_module_disable(&qspi->priv, 0); 950 951 return &qspi->slave; 952 } 953 954 void spi_free_slave(struct spi_slave *slave) 955 { 956 struct fsl_qspi *qspi = to_qspi_spi(slave); 957 958 free(qspi); 959 } 960 961 int spi_claim_bus(struct spi_slave *slave) 962 { 963 return 0; 964 } 965 966 void spi_release_bus(struct spi_slave *slave) 967 { 968 /* Nothing to do */ 969 } 970 971 int spi_xfer(struct spi_slave *slave, unsigned int bitlen, 972 const void *dout, void *din, unsigned long flags) 973 { 974 struct fsl_qspi *qspi = to_qspi_spi(slave); 975 976 return qspi_xfer(&qspi->priv, bitlen, dout, din, flags); 977 } 978 979 void spi_init(void) 980 { 981 /* Nothing to do */ 982 } 983 #else 984 static int fsl_qspi_child_pre_probe(struct udevice *dev) 985 { 986 struct spi_slave *slave = dev_get_parent_priv(dev); 987 988 slave->max_write_size = TX_BUFFER_SIZE; 989 990 return 0; 991 } 992 993 static int fsl_qspi_probe(struct udevice *bus) 994 { 995 u32 mcr_val; 996 u32 amba_size_per_chip; 997 struct fsl_qspi_platdata *plat = dev_get_platdata(bus); 998 struct fsl_qspi_priv *priv = dev_get_priv(bus); 999 struct dm_spi_bus *dm_spi_bus; 1000 int i, ret; 1001 1002 dm_spi_bus = bus->uclass_priv; 1003 1004 dm_spi_bus->max_hz = plat->speed_hz; 1005 1006 priv->regs = (struct fsl_qspi_regs *)(uintptr_t)plat->reg_base; 1007 priv->flags = plat->flags; 1008 1009 priv->speed_hz = plat->speed_hz; 1010 /* 1011 * QSPI SFADR width is 32bits, the max dest addr is 4GB-1. 1012 * AMBA memory zone should be located on the 0~4GB space 1013 * even on a 64bits cpu. 1014 */ 1015 priv->amba_base[0] = (u32)plat->amba_base; 1016 priv->amba_total_size = (u32)plat->amba_total_size; 1017 priv->flash_num = plat->flash_num; 1018 priv->num_chipselect = plat->num_chipselect; 1019 1020 /* make sure controller is not busy anywhere */ 1021 ret = wait_for_bit_le32(&priv->regs->sr, 1022 QSPI_SR_BUSY_MASK | 1023 QSPI_SR_AHB_ACC_MASK | 1024 QSPI_SR_IP_ACC_MASK, 1025 false, 100, false); 1026 1027 if (ret) { 1028 debug("ERROR : The controller is busy\n"); 1029 return ret; 1030 } 1031 1032 mcr_val = qspi_read32(priv->flags, &priv->regs->mcr); 1033 1034 /* Set endianness to LE for i.mx */ 1035 if (IS_ENABLED(CONFIG_MX6) || IS_ENABLED(CONFIG_MX7)) 1036 mcr_val = QSPI_MCR_END_CFD_LE; 1037 1038 qspi_write32(priv->flags, &priv->regs->mcr, 1039 QSPI_MCR_RESERVED_MASK | QSPI_MCR_MDIS_MASK | 1040 (mcr_val & QSPI_MCR_END_CFD_MASK)); 1041 1042 qspi_cfg_smpr(priv, ~(QSPI_SMPR_FSDLY_MASK | QSPI_SMPR_DDRSMP_MASK | 1043 QSPI_SMPR_FSPHS_MASK | QSPI_SMPR_HSENA_MASK), 0); 1044 1045 /* 1046 * Assign AMBA memory zone for every chipselect 1047 * QuadSPI has two channels, every channel has two chipselects. 1048 * If the property 'num-cs' in dts is 2, the AMBA memory will be divided 1049 * into two parts and assign to every channel. This indicate that every 1050 * channel only has one valid chipselect. 1051 * If the property 'num-cs' in dts is 4, the AMBA memory will be divided 1052 * into four parts and assign to every chipselect. 1053 * Every channel will has two valid chipselects. 1054 */ 1055 amba_size_per_chip = priv->amba_total_size >> 1056 (priv->num_chipselect >> 1); 1057 for (i = 1 ; i < priv->num_chipselect ; i++) 1058 priv->amba_base[i] = 1059 amba_size_per_chip + priv->amba_base[i - 1]; 1060 1061 /* 1062 * Any read access to non-implemented addresses will provide 1063 * undefined results. 1064 * 1065 * In case single die flash devices, TOP_ADDR_MEMA2 and 1066 * TOP_ADDR_MEMB2 should be initialized/programmed to 1067 * TOP_ADDR_MEMA1 and TOP_ADDR_MEMB1 respectively - in effect, 1068 * setting the size of these devices to 0. This would ensure 1069 * that the complete memory map is assigned to only one flash device. 1070 */ 1071 qspi_write32(priv->flags, &priv->regs->sfa1ad, 1072 priv->amba_base[0] + amba_size_per_chip); 1073 switch (priv->num_chipselect) { 1074 case 1: 1075 break; 1076 case 2: 1077 qspi_write32(priv->flags, &priv->regs->sfa2ad, 1078 priv->amba_base[1]); 1079 qspi_write32(priv->flags, &priv->regs->sfb1ad, 1080 priv->amba_base[1] + amba_size_per_chip); 1081 qspi_write32(priv->flags, &priv->regs->sfb2ad, 1082 priv->amba_base[1] + amba_size_per_chip); 1083 break; 1084 case 4: 1085 qspi_write32(priv->flags, &priv->regs->sfa2ad, 1086 priv->amba_base[2]); 1087 qspi_write32(priv->flags, &priv->regs->sfb1ad, 1088 priv->amba_base[3]); 1089 qspi_write32(priv->flags, &priv->regs->sfb2ad, 1090 priv->amba_base[3] + amba_size_per_chip); 1091 break; 1092 default: 1093 debug("Error: Unsupported chipselect number %u!\n", 1094 priv->num_chipselect); 1095 qspi_module_disable(priv, 1); 1096 return -EINVAL; 1097 } 1098 1099 qspi_set_lut(priv); 1100 1101 #ifdef CONFIG_SYS_FSL_QSPI_AHB 1102 qspi_init_ahb_read(priv); 1103 #endif 1104 1105 qspi_module_disable(priv, 0); 1106 1107 return 0; 1108 } 1109 1110 static int fsl_qspi_ofdata_to_platdata(struct udevice *bus) 1111 { 1112 struct fdt_resource res_regs, res_mem; 1113 struct fsl_qspi_platdata *plat = bus->platdata; 1114 const void *blob = gd->fdt_blob; 1115 int node = dev_of_offset(bus); 1116 int ret, flash_num = 0, subnode; 1117 1118 if (fdtdec_get_bool(blob, node, "big-endian")) 1119 plat->flags |= QSPI_FLAG_REGMAP_ENDIAN_BIG; 1120 1121 ret = fdt_get_named_resource(blob, node, "reg", "reg-names", 1122 "QuadSPI", &res_regs); 1123 if (ret) { 1124 debug("Error: can't get regs base addresses(ret = %d)!\n", ret); 1125 return -ENOMEM; 1126 } 1127 ret = fdt_get_named_resource(blob, node, "reg", "reg-names", 1128 "QuadSPI-memory", &res_mem); 1129 if (ret) { 1130 debug("Error: can't get AMBA base addresses(ret = %d)!\n", ret); 1131 return -ENOMEM; 1132 } 1133 1134 /* Count flash numbers */ 1135 fdt_for_each_subnode(subnode, blob, node) 1136 ++flash_num; 1137 1138 if (flash_num == 0) { 1139 debug("Error: Missing flashes!\n"); 1140 return -ENODEV; 1141 } 1142 1143 plat->speed_hz = fdtdec_get_int(blob, node, "spi-max-frequency", 1144 FSL_QSPI_DEFAULT_SCK_FREQ); 1145 plat->num_chipselect = fdtdec_get_int(blob, node, "num-cs", 1146 FSL_QSPI_MAX_CHIPSELECT_NUM); 1147 1148 plat->reg_base = res_regs.start; 1149 plat->amba_base = res_mem.start; 1150 plat->amba_total_size = res_mem.end - res_mem.start + 1; 1151 plat->flash_num = flash_num; 1152 1153 debug("%s: regs=<0x%llx> <0x%llx, 0x%llx>, max-frequency=%d, endianess=%s\n", 1154 __func__, 1155 (u64)plat->reg_base, 1156 (u64)plat->amba_base, 1157 (u64)plat->amba_total_size, 1158 plat->speed_hz, 1159 plat->flags & QSPI_FLAG_REGMAP_ENDIAN_BIG ? "be" : "le" 1160 ); 1161 1162 return 0; 1163 } 1164 1165 static int fsl_qspi_xfer(struct udevice *dev, unsigned int bitlen, 1166 const void *dout, void *din, unsigned long flags) 1167 { 1168 struct fsl_qspi_priv *priv; 1169 struct udevice *bus; 1170 1171 bus = dev->parent; 1172 priv = dev_get_priv(bus); 1173 1174 return qspi_xfer(priv, bitlen, dout, din, flags); 1175 } 1176 1177 static int fsl_qspi_claim_bus(struct udevice *dev) 1178 { 1179 struct fsl_qspi_priv *priv; 1180 struct udevice *bus; 1181 struct dm_spi_slave_platdata *slave_plat = dev_get_parent_platdata(dev); 1182 int ret; 1183 1184 bus = dev->parent; 1185 priv = dev_get_priv(bus); 1186 1187 /* make sure controller is not busy anywhere */ 1188 ret = wait_for_bit_le32(&priv->regs->sr, 1189 QSPI_SR_BUSY_MASK | 1190 QSPI_SR_AHB_ACC_MASK | 1191 QSPI_SR_IP_ACC_MASK, 1192 false, 100, false); 1193 1194 if (ret) { 1195 debug("ERROR : The controller is busy\n"); 1196 return ret; 1197 } 1198 1199 priv->cur_amba_base = priv->amba_base[slave_plat->cs]; 1200 1201 qspi_module_disable(priv, 0); 1202 1203 return 0; 1204 } 1205 1206 static int fsl_qspi_release_bus(struct udevice *dev) 1207 { 1208 struct fsl_qspi_priv *priv; 1209 struct udevice *bus; 1210 1211 bus = dev->parent; 1212 priv = dev_get_priv(bus); 1213 1214 qspi_module_disable(priv, 1); 1215 1216 return 0; 1217 } 1218 1219 static int fsl_qspi_set_speed(struct udevice *bus, uint speed) 1220 { 1221 /* Nothing to do */ 1222 return 0; 1223 } 1224 1225 static int fsl_qspi_set_mode(struct udevice *bus, uint mode) 1226 { 1227 /* Nothing to do */ 1228 return 0; 1229 } 1230 1231 static const struct dm_spi_ops fsl_qspi_ops = { 1232 .claim_bus = fsl_qspi_claim_bus, 1233 .release_bus = fsl_qspi_release_bus, 1234 .xfer = fsl_qspi_xfer, 1235 .set_speed = fsl_qspi_set_speed, 1236 .set_mode = fsl_qspi_set_mode, 1237 }; 1238 1239 static const struct udevice_id fsl_qspi_ids[] = { 1240 { .compatible = "fsl,vf610-qspi" }, 1241 { .compatible = "fsl,imx6sx-qspi" }, 1242 { .compatible = "fsl,imx6ul-qspi" }, 1243 { .compatible = "fsl,imx7d-qspi" }, 1244 { } 1245 }; 1246 1247 U_BOOT_DRIVER(fsl_qspi) = { 1248 .name = "fsl_qspi", 1249 .id = UCLASS_SPI, 1250 .of_match = fsl_qspi_ids, 1251 .ops = &fsl_qspi_ops, 1252 .ofdata_to_platdata = fsl_qspi_ofdata_to_platdata, 1253 .platdata_auto_alloc_size = sizeof(struct fsl_qspi_platdata), 1254 .priv_auto_alloc_size = sizeof(struct fsl_qspi_priv), 1255 .probe = fsl_qspi_probe, 1256 .child_pre_probe = fsl_qspi_child_pre_probe, 1257 }; 1258 #endif 1259