1 /* 2 * Copyright (C) 2007 Atmel Corporation 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 #include <common.h> 7 #include <clk.h> 8 #include <dm.h> 9 #include <fdtdec.h> 10 #include <spi.h> 11 #include <malloc.h> 12 #include <wait_bit.h> 13 14 #include <asm/io.h> 15 16 #include <asm/arch/clk.h> 17 #include <asm/arch/hardware.h> 18 #ifdef CONFIG_DM_SPI 19 #include <asm/arch/at91_spi.h> 20 #endif 21 #ifdef CONFIG_DM_GPIO 22 #include <asm/gpio.h> 23 #endif 24 25 #include "atmel_spi.h" 26 27 DECLARE_GLOBAL_DATA_PTR; 28 29 #ifndef CONFIG_DM_SPI 30 31 static int spi_has_wdrbt(struct atmel_spi_slave *slave) 32 { 33 unsigned int ver; 34 35 ver = spi_readl(slave, VERSION); 36 37 return (ATMEL_SPI_VERSION_REV(ver) >= 0x210); 38 } 39 40 void spi_init() 41 { 42 43 } 44 45 struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs, 46 unsigned int max_hz, unsigned int mode) 47 { 48 struct atmel_spi_slave *as; 49 unsigned int scbr; 50 u32 csrx; 51 void *regs; 52 53 if (!spi_cs_is_valid(bus, cs)) 54 return NULL; 55 56 switch (bus) { 57 case 0: 58 regs = (void *)ATMEL_BASE_SPI0; 59 break; 60 #ifdef ATMEL_BASE_SPI1 61 case 1: 62 regs = (void *)ATMEL_BASE_SPI1; 63 break; 64 #endif 65 #ifdef ATMEL_BASE_SPI2 66 case 2: 67 regs = (void *)ATMEL_BASE_SPI2; 68 break; 69 #endif 70 #ifdef ATMEL_BASE_SPI3 71 case 3: 72 regs = (void *)ATMEL_BASE_SPI3; 73 break; 74 #endif 75 default: 76 return NULL; 77 } 78 79 80 scbr = (get_spi_clk_rate(bus) + max_hz - 1) / max_hz; 81 if (scbr > ATMEL_SPI_CSRx_SCBR_MAX) 82 /* Too low max SCK rate */ 83 return NULL; 84 if (scbr < 1) 85 scbr = 1; 86 87 csrx = ATMEL_SPI_CSRx_SCBR(scbr); 88 csrx |= ATMEL_SPI_CSRx_BITS(ATMEL_SPI_BITS_8); 89 if (!(mode & SPI_CPHA)) 90 csrx |= ATMEL_SPI_CSRx_NCPHA; 91 if (mode & SPI_CPOL) 92 csrx |= ATMEL_SPI_CSRx_CPOL; 93 94 as = spi_alloc_slave(struct atmel_spi_slave, bus, cs); 95 if (!as) 96 return NULL; 97 98 as->regs = regs; 99 as->mr = ATMEL_SPI_MR_MSTR | ATMEL_SPI_MR_MODFDIS 100 | ATMEL_SPI_MR_PCS(~(1 << cs) & 0xf); 101 if (spi_has_wdrbt(as)) 102 as->mr |= ATMEL_SPI_MR_WDRBT; 103 104 spi_writel(as, CSR(cs), csrx); 105 106 return &as->slave; 107 } 108 109 void spi_free_slave(struct spi_slave *slave) 110 { 111 struct atmel_spi_slave *as = to_atmel_spi(slave); 112 113 free(as); 114 } 115 116 int spi_claim_bus(struct spi_slave *slave) 117 { 118 struct atmel_spi_slave *as = to_atmel_spi(slave); 119 120 /* Enable the SPI hardware */ 121 spi_writel(as, CR, ATMEL_SPI_CR_SPIEN); 122 123 /* 124 * Select the slave. This should set SCK to the correct 125 * initial state, etc. 126 */ 127 spi_writel(as, MR, as->mr); 128 129 return 0; 130 } 131 132 void spi_release_bus(struct spi_slave *slave) 133 { 134 struct atmel_spi_slave *as = to_atmel_spi(slave); 135 136 /* Disable the SPI hardware */ 137 spi_writel(as, CR, ATMEL_SPI_CR_SPIDIS); 138 } 139 140 int spi_xfer(struct spi_slave *slave, unsigned int bitlen, 141 const void *dout, void *din, unsigned long flags) 142 { 143 struct atmel_spi_slave *as = to_atmel_spi(slave); 144 unsigned int len_tx; 145 unsigned int len_rx; 146 unsigned int len; 147 u32 status; 148 const u8 *txp = dout; 149 u8 *rxp = din; 150 u8 value; 151 152 if (bitlen == 0) 153 /* Finish any previously submitted transfers */ 154 goto out; 155 156 /* 157 * TODO: The controller can do non-multiple-of-8 bit 158 * transfers, but this driver currently doesn't support it. 159 * 160 * It's also not clear how such transfers are supposed to be 161 * represented as a stream of bytes...this is a limitation of 162 * the current SPI interface. 163 */ 164 if (bitlen % 8) { 165 /* Errors always terminate an ongoing transfer */ 166 flags |= SPI_XFER_END; 167 goto out; 168 } 169 170 len = bitlen / 8; 171 172 /* 173 * The controller can do automatic CS control, but it is 174 * somewhat quirky, and it doesn't really buy us much anyway 175 * in the context of U-Boot. 176 */ 177 if (flags & SPI_XFER_BEGIN) { 178 spi_cs_activate(slave); 179 /* 180 * sometimes the RDR is not empty when we get here, 181 * in theory that should not happen, but it DOES happen. 182 * Read it here to be on the safe side. 183 * That also clears the OVRES flag. Required if the 184 * following loop exits due to OVRES! 185 */ 186 spi_readl(as, RDR); 187 } 188 189 for (len_tx = 0, len_rx = 0; len_rx < len; ) { 190 status = spi_readl(as, SR); 191 192 if (status & ATMEL_SPI_SR_OVRES) 193 return -1; 194 195 if (len_tx < len && (status & ATMEL_SPI_SR_TDRE)) { 196 if (txp) 197 value = *txp++; 198 else 199 value = 0; 200 spi_writel(as, TDR, value); 201 len_tx++; 202 } 203 if (status & ATMEL_SPI_SR_RDRF) { 204 value = spi_readl(as, RDR); 205 if (rxp) 206 *rxp++ = value; 207 len_rx++; 208 } 209 } 210 211 out: 212 if (flags & SPI_XFER_END) { 213 /* 214 * Wait until the transfer is completely done before 215 * we deactivate CS. 216 */ 217 do { 218 status = spi_readl(as, SR); 219 } while (!(status & ATMEL_SPI_SR_TXEMPTY)); 220 221 spi_cs_deactivate(slave); 222 } 223 224 return 0; 225 } 226 227 #else 228 229 #define MAX_CS_COUNT 4 230 231 struct atmel_spi_platdata { 232 struct at91_spi *regs; 233 }; 234 235 struct atmel_spi_priv { 236 unsigned int freq; /* Default frequency */ 237 unsigned int mode; 238 ulong bus_clk_rate; 239 struct gpio_desc cs_gpios[MAX_CS_COUNT]; 240 }; 241 242 static int atmel_spi_claim_bus(struct udevice *dev) 243 { 244 struct udevice *bus = dev_get_parent(dev); 245 struct atmel_spi_platdata *bus_plat = dev_get_platdata(bus); 246 struct atmel_spi_priv *priv = dev_get_priv(bus); 247 struct dm_spi_slave_platdata *slave_plat = dev_get_parent_platdata(dev); 248 struct at91_spi *reg_base = bus_plat->regs; 249 u32 cs = slave_plat->cs; 250 u32 freq = priv->freq; 251 u32 scbr, csrx, mode; 252 253 scbr = (priv->bus_clk_rate + freq - 1) / freq; 254 if (scbr > ATMEL_SPI_CSRx_SCBR_MAX) 255 return -EINVAL; 256 257 if (scbr < 1) 258 scbr = 1; 259 260 csrx = ATMEL_SPI_CSRx_SCBR(scbr); 261 csrx |= ATMEL_SPI_CSRx_BITS(ATMEL_SPI_BITS_8); 262 263 if (!(priv->mode & SPI_CPHA)) 264 csrx |= ATMEL_SPI_CSRx_NCPHA; 265 if (priv->mode & SPI_CPOL) 266 csrx |= ATMEL_SPI_CSRx_CPOL; 267 268 writel(csrx, ®_base->csr[cs]); 269 270 mode = ATMEL_SPI_MR_MSTR | 271 ATMEL_SPI_MR_MODFDIS | 272 ATMEL_SPI_MR_WDRBT | 273 ATMEL_SPI_MR_PCS(~(1 << cs)); 274 275 writel(mode, ®_base->mr); 276 277 writel(ATMEL_SPI_CR_SPIEN, ®_base->cr); 278 279 return 0; 280 } 281 282 static int atmel_spi_release_bus(struct udevice *dev) 283 { 284 struct udevice *bus = dev_get_parent(dev); 285 struct atmel_spi_platdata *bus_plat = dev_get_platdata(bus); 286 287 writel(ATMEL_SPI_CR_SPIDIS, &bus_plat->regs->cr); 288 289 return 0; 290 } 291 292 static void atmel_spi_cs_activate(struct udevice *dev) 293 { 294 struct udevice *bus = dev_get_parent(dev); 295 struct atmel_spi_priv *priv = dev_get_priv(bus); 296 struct dm_spi_slave_platdata *slave_plat = dev_get_parent_platdata(dev); 297 u32 cs = slave_plat->cs; 298 299 if (!dm_gpio_is_valid(&priv->cs_gpios[cs])) 300 return; 301 302 dm_gpio_set_value(&priv->cs_gpios[cs], 0); 303 } 304 305 static void atmel_spi_cs_deactivate(struct udevice *dev) 306 { 307 struct udevice *bus = dev_get_parent(dev); 308 struct atmel_spi_priv *priv = dev_get_priv(bus); 309 struct dm_spi_slave_platdata *slave_plat = dev_get_parent_platdata(dev); 310 u32 cs = slave_plat->cs; 311 312 if (!dm_gpio_is_valid(&priv->cs_gpios[cs])) 313 return; 314 315 dm_gpio_set_value(&priv->cs_gpios[cs], 1); 316 } 317 318 static int atmel_spi_xfer(struct udevice *dev, unsigned int bitlen, 319 const void *dout, void *din, unsigned long flags) 320 { 321 struct udevice *bus = dev_get_parent(dev); 322 struct atmel_spi_platdata *bus_plat = dev_get_platdata(bus); 323 struct at91_spi *reg_base = bus_plat->regs; 324 325 u32 len_tx, len_rx, len; 326 u32 status; 327 const u8 *txp = dout; 328 u8 *rxp = din; 329 u8 value; 330 331 if (bitlen == 0) 332 goto out; 333 334 /* 335 * The controller can do non-multiple-of-8 bit 336 * transfers, but this driver currently doesn't support it. 337 * 338 * It's also not clear how such transfers are supposed to be 339 * represented as a stream of bytes...this is a limitation of 340 * the current SPI interface. 341 */ 342 if (bitlen % 8) { 343 /* Errors always terminate an ongoing transfer */ 344 flags |= SPI_XFER_END; 345 goto out; 346 } 347 348 len = bitlen / 8; 349 350 /* 351 * The controller can do automatic CS control, but it is 352 * somewhat quirky, and it doesn't really buy us much anyway 353 * in the context of U-Boot. 354 */ 355 if (flags & SPI_XFER_BEGIN) { 356 atmel_spi_cs_activate(dev); 357 358 /* 359 * sometimes the RDR is not empty when we get here, 360 * in theory that should not happen, but it DOES happen. 361 * Read it here to be on the safe side. 362 * That also clears the OVRES flag. Required if the 363 * following loop exits due to OVRES! 364 */ 365 readl(®_base->rdr); 366 } 367 368 for (len_tx = 0, len_rx = 0; len_rx < len; ) { 369 status = readl(®_base->sr); 370 371 if (status & ATMEL_SPI_SR_OVRES) 372 return -1; 373 374 if ((len_tx < len) && (status & ATMEL_SPI_SR_TDRE)) { 375 if (txp) 376 value = *txp++; 377 else 378 value = 0; 379 writel(value, ®_base->tdr); 380 len_tx++; 381 } 382 383 if (status & ATMEL_SPI_SR_RDRF) { 384 value = readl(®_base->rdr); 385 if (rxp) 386 *rxp++ = value; 387 len_rx++; 388 } 389 } 390 391 out: 392 if (flags & SPI_XFER_END) { 393 /* 394 * Wait until the transfer is completely done before 395 * we deactivate CS. 396 */ 397 wait_for_bit_le32(®_base->sr, 398 ATMEL_SPI_SR_TXEMPTY, true, 1000, false); 399 400 atmel_spi_cs_deactivate(dev); 401 } 402 403 return 0; 404 } 405 406 static int atmel_spi_set_speed(struct udevice *bus, uint speed) 407 { 408 struct atmel_spi_priv *priv = dev_get_priv(bus); 409 410 priv->freq = speed; 411 412 return 0; 413 } 414 415 static int atmel_spi_set_mode(struct udevice *bus, uint mode) 416 { 417 struct atmel_spi_priv *priv = dev_get_priv(bus); 418 419 priv->mode = mode; 420 421 return 0; 422 } 423 424 static const struct dm_spi_ops atmel_spi_ops = { 425 .claim_bus = atmel_spi_claim_bus, 426 .release_bus = atmel_spi_release_bus, 427 .xfer = atmel_spi_xfer, 428 .set_speed = atmel_spi_set_speed, 429 .set_mode = atmel_spi_set_mode, 430 /* 431 * cs_info is not needed, since we require all chip selects to be 432 * in the device tree explicitly 433 */ 434 }; 435 436 static int atmel_spi_enable_clk(struct udevice *bus) 437 { 438 struct atmel_spi_priv *priv = dev_get_priv(bus); 439 struct clk clk; 440 ulong clk_rate; 441 int ret; 442 443 ret = clk_get_by_index(bus, 0, &clk); 444 if (ret) 445 return -EINVAL; 446 447 ret = clk_enable(&clk); 448 if (ret) 449 return ret; 450 451 clk_rate = clk_get_rate(&clk); 452 if (!clk_rate) 453 return -EINVAL; 454 455 priv->bus_clk_rate = clk_rate; 456 457 clk_free(&clk); 458 459 return 0; 460 } 461 462 static int atmel_spi_probe(struct udevice *bus) 463 { 464 struct atmel_spi_platdata *bus_plat = dev_get_platdata(bus); 465 struct atmel_spi_priv *priv = dev_get_priv(bus); 466 int i, ret; 467 468 ret = atmel_spi_enable_clk(bus); 469 if (ret) 470 return ret; 471 472 bus_plat->regs = (struct at91_spi *)devfdt_get_addr(bus); 473 474 ret = gpio_request_list_by_name(bus, "cs-gpios", priv->cs_gpios, 475 ARRAY_SIZE(priv->cs_gpios), 0); 476 if (ret < 0) { 477 pr_err("Can't get %s gpios! Error: %d", bus->name, ret); 478 return ret; 479 } 480 481 for(i = 0; i < ARRAY_SIZE(priv->cs_gpios); i++) { 482 if (!dm_gpio_is_valid(&priv->cs_gpios[i])) 483 continue; 484 485 dm_gpio_set_dir_flags(&priv->cs_gpios[i], 486 GPIOD_IS_OUT | GPIOD_IS_OUT_ACTIVE); 487 } 488 489 writel(ATMEL_SPI_CR_SWRST, &bus_plat->regs->cr); 490 491 return 0; 492 } 493 494 static const struct udevice_id atmel_spi_ids[] = { 495 { .compatible = "atmel,at91rm9200-spi" }, 496 { } 497 }; 498 499 U_BOOT_DRIVER(atmel_spi) = { 500 .name = "atmel_spi", 501 .id = UCLASS_SPI, 502 .of_match = atmel_spi_ids, 503 .ops = &atmel_spi_ops, 504 .platdata_auto_alloc_size = sizeof(struct atmel_spi_platdata), 505 .priv_auto_alloc_size = sizeof(struct atmel_spi_priv), 506 .probe = atmel_spi_probe, 507 }; 508 #endif 509