xref: /openbmc/u-boot/drivers/sound/wm8994.c (revision 224f7452)
1 // SPDX-License-Identifier: GPL-2.0+
2 /*
3  * Copyright (C) 2012 Samsung Electronics
4  * R. Chandrasekar <rcsekar@samsung.com>
5  */
6 #include <common.h>
7 #include <audio_codec.h>
8 #include <dm.h>
9 #include <div64.h>
10 #include <fdtdec.h>
11 #include <i2c.h>
12 #include <i2s.h>
13 #include <sound.h>
14 #include <asm/gpio.h>
15 #include <asm/io.h>
16 #include <asm/arch/clk.h>
17 #include <asm/arch/cpu.h>
18 #include <asm/arch/sound.h>
19 #include "wm8994.h"
20 #include "wm8994_registers.h"
21 
22 /* defines for wm8994 system clock selection */
23 #define SEL_MCLK1	0x00
24 #define SEL_MCLK2	0x08
25 #define SEL_FLL1	0x10
26 #define SEL_FLL2	0x18
27 
28 /* fll config to configure fll */
29 struct wm8994_fll_config {
30 	int src;	/* Source */
31 	int in;		/* Input frequency in Hz */
32 	int out;	/* output frequency in Hz */
33 };
34 
35 /* codec private data */
36 struct wm8994_priv {
37 	enum wm8994_type type;		/* codec type of wolfson */
38 	int revision;			/* Revision */
39 	int sysclk[WM8994_MAX_AIF];	/* System clock frequency in Hz  */
40 	int mclk[WM8994_MAX_AIF];	/* master clock frequency in Hz */
41 	int aifclk[WM8994_MAX_AIF];	/* audio interface clock in Hz   */
42 	struct wm8994_fll_config fll[2]; /* fll config to configure fll */
43 	struct udevice *dev;
44 };
45 
46 /* wm 8994 supported sampling rate values */
47 static unsigned int src_rate[] = {
48 			 8000, 11025, 12000, 16000, 22050, 24000,
49 			 32000, 44100, 48000, 88200, 96000
50 };
51 
52 /* op clock divisions */
53 static int opclk_divs[] = { 10, 20, 30, 40, 55, 60, 80, 120, 160 };
54 
55 /* lr clock frame size ratio */
56 static int fs_ratios[] = {
57 	64, 128, 192, 256, 348, 512, 768, 1024, 1408, 1536
58 };
59 
60 /* bit clock divisors */
61 static int bclk_divs[] = {
62 	10, 15, 20, 30, 40, 50, 60, 80, 110, 120, 160, 220, 240, 320, 440, 480,
63 	640, 880, 960, 1280, 1760, 1920
64 };
65 
66 /*
67  * Writes value to a device register through i2c
68  *
69  * @param priv	Private data for driver
70  * @param reg	reg number to be write
71  * @param data	data to be writen to the above registor
72  *
73  * @return	int value 1 for change, 0 for no change or negative error code.
74  */
75 static int wm8994_i2c_write(struct wm8994_priv *priv, unsigned int reg,
76 			    unsigned short data)
77 {
78 	unsigned char val[2];
79 
80 	val[0] = (unsigned char)((data >> 8) & 0xff);
81 	val[1] = (unsigned char)(data & 0xff);
82 	debug("Write Addr : 0x%04X, Data :  0x%04X\n", reg, data);
83 
84 	return dm_i2c_write(priv->dev, reg, val, 2);
85 }
86 
87 /*
88  * Read a value from a device register through i2c
89  *
90  * @param priv	Private data for driver
91  * @param reg	reg number to be read
92  * @param data	address of read data to be stored
93  *
94  * @return	int value 0 for success, -1 in case of error.
95  */
96 static unsigned int wm8994_i2c_read(struct wm8994_priv *priv, unsigned int reg,
97 				    unsigned short *data)
98 {
99 	unsigned char val[2];
100 	int ret;
101 
102 	ret = dm_i2c_read(priv->dev, reg, val, 1);
103 	if (ret != 0) {
104 		debug("%s: Error while reading register %#04x\n",
105 		      __func__, reg);
106 		return -1;
107 	}
108 
109 	*data = val[0];
110 	*data <<= 8;
111 	*data |= val[1];
112 
113 	return 0;
114 }
115 
116 /*
117  * update device register bits through i2c
118  *
119  * @param priv	Private data for driver
120  * @param reg	codec register
121  * @param mask	register mask
122  * @param value	new value
123  *
124  * @return int value 1 if change in the register value,
125  * 0 for no change or negative error code.
126  */
127 static int wm8994_bic_or(struct wm8994_priv *priv, unsigned int reg,
128 			 unsigned short mask, unsigned short value)
129 {
130 	int change , ret = 0;
131 	unsigned short old, new;
132 
133 	if (wm8994_i2c_read(priv, reg, &old) != 0)
134 		return -1;
135 	new = (old & ~mask) | (value & mask);
136 	change  = (old != new) ? 1 : 0;
137 	if (change)
138 		ret = wm8994_i2c_write(priv, reg, new);
139 	if (ret < 0)
140 		return ret;
141 
142 	return change;
143 }
144 
145 /*
146  * Sets i2s set format
147  *
148  * @param priv		wm8994 information
149  * @param aif_id	Interface ID
150  * @param fmt		i2S format
151  *
152  * @return -1 for error and 0  Success.
153  */
154 static int wm8994_set_fmt(struct wm8994_priv *priv, int aif_id, uint fmt)
155 {
156 	int ms_reg;
157 	int aif_reg;
158 	int ms = 0;
159 	int aif = 0;
160 	int aif_clk = 0;
161 	int error = 0;
162 
163 	switch (aif_id) {
164 	case 1:
165 		ms_reg = WM8994_AIF1_MASTER_SLAVE;
166 		aif_reg = WM8994_AIF1_CONTROL_1;
167 		aif_clk = WM8994_AIF1_CLOCKING_1;
168 		break;
169 	case 2:
170 		ms_reg = WM8994_AIF2_MASTER_SLAVE;
171 		aif_reg = WM8994_AIF2_CONTROL_1;
172 		aif_clk = WM8994_AIF2_CLOCKING_1;
173 		break;
174 	default:
175 		debug("%s: Invalid audio interface selection\n", __func__);
176 		return -1;
177 	}
178 
179 	switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) {
180 	case SND_SOC_DAIFMT_CBS_CFS:
181 		break;
182 	case SND_SOC_DAIFMT_CBM_CFM:
183 		ms = WM8994_AIF1_MSTR;
184 		break;
185 	default:
186 		debug("%s: Invalid i2s master selection\n", __func__);
187 		return -1;
188 	}
189 
190 	switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
191 	case SND_SOC_DAIFMT_DSP_B:
192 		aif |= WM8994_AIF1_LRCLK_INV;
193 	case SND_SOC_DAIFMT_DSP_A:
194 		aif |= 0x18;
195 		break;
196 	case SND_SOC_DAIFMT_I2S:
197 		aif |= 0x10;
198 		break;
199 	case SND_SOC_DAIFMT_RIGHT_J:
200 		break;
201 	case SND_SOC_DAIFMT_LEFT_J:
202 		aif |= 0x8;
203 		break;
204 	default:
205 		debug("%s: Invalid i2s format selection\n", __func__);
206 		return -1;
207 	}
208 
209 	switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
210 	case SND_SOC_DAIFMT_DSP_A:
211 	case SND_SOC_DAIFMT_DSP_B:
212 		/* frame inversion not valid for DSP modes */
213 		switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
214 		case SND_SOC_DAIFMT_NB_NF:
215 			break;
216 		case SND_SOC_DAIFMT_IB_NF:
217 			aif |= WM8994_AIF1_BCLK_INV;
218 			break;
219 		default:
220 			debug("%s: Invalid i2s frame inverse selection\n",
221 			      __func__);
222 			return -1;
223 		}
224 		break;
225 
226 	case SND_SOC_DAIFMT_I2S:
227 	case SND_SOC_DAIFMT_RIGHT_J:
228 	case SND_SOC_DAIFMT_LEFT_J:
229 		switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
230 		case SND_SOC_DAIFMT_NB_NF:
231 			break;
232 		case SND_SOC_DAIFMT_IB_IF:
233 			aif |= WM8994_AIF1_BCLK_INV | WM8994_AIF1_LRCLK_INV;
234 			break;
235 		case SND_SOC_DAIFMT_IB_NF:
236 			aif |= WM8994_AIF1_BCLK_INV;
237 			break;
238 		case SND_SOC_DAIFMT_NB_IF:
239 			aif |= WM8994_AIF1_LRCLK_INV;
240 			break;
241 		default:
242 			debug("%s: Invalid i2s clock polarity selection\n",
243 			      __func__);
244 			return -1;
245 		}
246 		break;
247 	default:
248 		debug("%s: Invalid i2s format selection\n", __func__);
249 		return -1;
250 	}
251 
252 	error = wm8994_bic_or(priv, aif_reg, WM8994_AIF1_BCLK_INV |
253 			      WM8994_AIF1_LRCLK_INV_MASK |
254 			       WM8994_AIF1_FMT_MASK, aif);
255 
256 	error |= wm8994_bic_or(priv, ms_reg, WM8994_AIF1_MSTR_MASK, ms);
257 	error |= wm8994_bic_or(priv, aif_clk, WM8994_AIF1CLK_ENA_MASK,
258 			       WM8994_AIF1CLK_ENA);
259 	if (error < 0) {
260 		debug("%s: codec register access error\n", __func__);
261 		return -1;
262 	}
263 
264 	return 0;
265 }
266 
267 /*
268  * Sets hw params FOR WM8994
269  *
270  * @param priv			wm8994 information pointer
271  * @param aif_id		Audio interface ID
272  * @param sampling_rate		Sampling rate
273  * @param bits_per_sample	Bits per sample
274  * @param Channels		Channels in the given audio input
275  *
276  * @return -1 for error  and 0  Success.
277  */
278 static int wm8994_hw_params(struct wm8994_priv *priv, int aif_id,
279 			    uint sampling_rate, uint bits_per_sample,
280 			    uint channels)
281 {
282 	int aif1_reg;
283 	int aif2_reg;
284 	int bclk_reg;
285 	int bclk = 0;
286 	int rate_reg;
287 	int aif1 = 0;
288 	int aif2 = 0;
289 	int rate_val = 0;
290 	int id = aif_id - 1;
291 	int i, cur_val, best_val, bclk_rate, best;
292 	unsigned short reg_data;
293 	int ret = 0;
294 
295 	switch (aif_id) {
296 	case 1:
297 		aif1_reg = WM8994_AIF1_CONTROL_1;
298 		aif2_reg = WM8994_AIF1_CONTROL_2;
299 		bclk_reg = WM8994_AIF1_BCLK;
300 		rate_reg = WM8994_AIF1_RATE;
301 		break;
302 	case 2:
303 		aif1_reg = WM8994_AIF2_CONTROL_1;
304 		aif2_reg = WM8994_AIF2_CONTROL_2;
305 		bclk_reg = WM8994_AIF2_BCLK;
306 		rate_reg = WM8994_AIF2_RATE;
307 		break;
308 	default:
309 		return -1;
310 	}
311 
312 	bclk_rate = sampling_rate * 32;
313 	switch (bits_per_sample) {
314 	case 16:
315 		bclk_rate *= 16;
316 		break;
317 	case 20:
318 		bclk_rate *= 20;
319 		aif1 |= 0x20;
320 		break;
321 	case 24:
322 		bclk_rate *= 24;
323 		aif1 |= 0x40;
324 		break;
325 	case 32:
326 		bclk_rate *= 32;
327 		aif1 |= 0x60;
328 		break;
329 	default:
330 		return -1;
331 	}
332 
333 	/* Try to find an appropriate sample rate; look for an exact match. */
334 	for (i = 0; i < ARRAY_SIZE(src_rate); i++)
335 		if (src_rate[i] == sampling_rate)
336 			break;
337 
338 	if (i == ARRAY_SIZE(src_rate)) {
339 		debug("%s: Could not get the best matching samplingrate\n",
340 		      __func__);
341 		return -1;
342 	}
343 
344 	rate_val |= i << WM8994_AIF1_SR_SHIFT;
345 
346 	/* AIFCLK/fs ratio; look for a close match in either direction */
347 	best = 0;
348 	best_val = abs((fs_ratios[0] * sampling_rate) - priv->aifclk[id]);
349 
350 	for (i = 1; i < ARRAY_SIZE(fs_ratios); i++) {
351 		cur_val = abs(fs_ratios[i] * sampling_rate - priv->aifclk[id]);
352 		if (cur_val >= best_val)
353 			continue;
354 		best = i;
355 		best_val = cur_val;
356 	}
357 
358 	rate_val |= best;
359 
360 	/*
361 	 * We may not get quite the right frequency if using
362 	 * approximate clocks so look for the closest match that is
363 	 * higher than the target (we need to ensure that there enough
364 	 * BCLKs to clock out the samples).
365 	 */
366 	best = 0;
367 	for (i = 0; i < ARRAY_SIZE(bclk_divs); i++) {
368 		cur_val = (priv->aifclk[id] * 10 / bclk_divs[i]) - bclk_rate;
369 		if (cur_val < 0) /* BCLK table is sorted */
370 			break;
371 		best = i;
372 	}
373 
374 	if (i ==  ARRAY_SIZE(bclk_divs)) {
375 		debug("%s: Could not get the best matching bclk division\n",
376 		      __func__);
377 		return -1;
378 	}
379 
380 	bclk_rate = priv->aifclk[id] * 10 / bclk_divs[best];
381 	bclk |= best << WM8994_AIF1_BCLK_DIV_SHIFT;
382 
383 	if (wm8994_i2c_read(priv, aif1_reg, &reg_data) != 0) {
384 		debug("%s: AIF1 register read Failed\n", __func__);
385 		return -1;
386 	}
387 
388 	if ((channels == 1) && ((reg_data & 0x18) == 0x18))
389 		aif2 |= WM8994_AIF1_MONO;
390 
391 	if (priv->aifclk[id] == 0) {
392 		debug("%s:Audio interface clock not set\n", __func__);
393 		return -1;
394 	}
395 
396 	ret = wm8994_bic_or(priv, aif1_reg, WM8994_AIF1_WL_MASK, aif1);
397 	ret |= wm8994_bic_or(priv, aif2_reg, WM8994_AIF1_MONO, aif2);
398 	ret |= wm8994_bic_or(priv, bclk_reg, WM8994_AIF1_BCLK_DIV_MASK,
399 				  bclk);
400 	ret |= wm8994_bic_or(priv, rate_reg, WM8994_AIF1_SR_MASK |
401 				  WM8994_AIF1CLK_RATE_MASK, rate_val);
402 
403 	debug("rate vale = %x , bclk val= %x\n", rate_val, bclk);
404 
405 	if (ret < 0) {
406 		debug("%s: codec register access error\n", __func__);
407 		return -1;
408 	}
409 
410 	return 0;
411 }
412 
413 /*
414  * Configures Audio interface Clock
415  *
416  * @param priv		wm8994 information pointer
417  * @param aif		Audio Interface ID
418  *
419  * @return -1 for error  and 0  Success.
420  */
421 static int configure_aif_clock(struct wm8994_priv *priv, int aif)
422 {
423 	int rate;
424 	int reg1 = 0;
425 	int offset;
426 	int ret;
427 
428 	/* AIF(1/0) register adress offset calculated */
429 	if (aif-1)
430 		offset = 4;
431 	else
432 		offset = 0;
433 
434 	switch (priv->sysclk[aif - 1]) {
435 	case WM8994_SYSCLK_MCLK1:
436 		reg1 |= SEL_MCLK1;
437 		rate = priv->mclk[0];
438 		break;
439 
440 	case WM8994_SYSCLK_MCLK2:
441 		reg1 |= SEL_MCLK2;
442 		rate = priv->mclk[1];
443 		break;
444 
445 	case WM8994_SYSCLK_FLL1:
446 		reg1 |= SEL_FLL1;
447 		rate = priv->fll[0].out;
448 		break;
449 
450 	case WM8994_SYSCLK_FLL2:
451 		reg1 |= SEL_FLL2;
452 		rate = priv->fll[1].out;
453 		break;
454 
455 	default:
456 		debug("%s: Invalid input clock selection [%d]\n",
457 		      __func__, priv->sysclk[aif - 1]);
458 		return -1;
459 	}
460 
461 	/* if input clock frequenct is more than 135Mhz then divide */
462 	if (rate >= WM8994_MAX_INPUT_CLK_FREQ) {
463 		rate /= 2;
464 		reg1 |= WM8994_AIF1CLK_DIV;
465 	}
466 
467 	priv->aifclk[aif - 1] = rate;
468 
469 	ret = wm8994_bic_or(priv, WM8994_AIF1_CLOCKING_1 + offset,
470 			    WM8994_AIF1CLK_SRC_MASK | WM8994_AIF1CLK_DIV,
471 			    reg1);
472 
473 	if (aif == WM8994_AIF1)
474 		ret |= wm8994_bic_or(priv, WM8994_CLOCKING_1,
475 			WM8994_AIF1DSPCLK_ENA_MASK | WM8994_SYSDSPCLK_ENA_MASK,
476 			WM8994_AIF1DSPCLK_ENA | WM8994_SYSDSPCLK_ENA);
477 	else if (aif == WM8994_AIF2)
478 		ret |= wm8994_bic_or(priv, WM8994_CLOCKING_1,
479 			WM8994_SYSCLK_SRC | WM8994_AIF2DSPCLK_ENA_MASK |
480 			WM8994_SYSDSPCLK_ENA_MASK, WM8994_SYSCLK_SRC |
481 			WM8994_AIF2DSPCLK_ENA | WM8994_SYSDSPCLK_ENA);
482 
483 	if (ret < 0) {
484 		debug("%s: codec register access error\n", __func__);
485 		return -1;
486 	}
487 
488 	return 0;
489 }
490 
491 /*
492  * Configures Audio interface  for the given frequency
493  *
494  * @param priv		wm8994 information
495  * @param aif_id	Audio Interface
496  * @param clk_id	Input Clock ID
497  * @param freq		Sampling frequency in Hz
498  *
499  * @return -1 for error and 0 success.
500  */
501 static int wm8994_set_sysclk(struct wm8994_priv *priv, int aif_id, int clk_id,
502 			     unsigned int freq)
503 {
504 	int i;
505 	int ret = 0;
506 
507 	priv->sysclk[aif_id - 1] = clk_id;
508 
509 	switch (clk_id) {
510 	case WM8994_SYSCLK_MCLK1:
511 		priv->mclk[0] = freq;
512 		if (aif_id == 2) {
513 			ret = wm8994_bic_or(priv, WM8994_AIF1_CLOCKING_2,
514 					    WM8994_AIF2DAC_DIV_MASK, 0);
515 		}
516 		break;
517 
518 	case WM8994_SYSCLK_MCLK2:
519 		/* TODO: Set GPIO AF */
520 		priv->mclk[1] = freq;
521 		break;
522 
523 	case WM8994_SYSCLK_FLL1:
524 	case WM8994_SYSCLK_FLL2:
525 		break;
526 
527 	case WM8994_SYSCLK_OPCLK:
528 		/*
529 		 * Special case - a division (times 10) is given and
530 		 * no effect on main clocking.
531 		 */
532 		if (freq) {
533 			for (i = 0; i < ARRAY_SIZE(opclk_divs); i++)
534 				if (opclk_divs[i] == freq)
535 					break;
536 			if (i == ARRAY_SIZE(opclk_divs)) {
537 				debug("%s frequency divisor not found\n",
538 				      __func__);
539 				return -1;
540 			}
541 			ret = wm8994_bic_or(priv, WM8994_CLOCKING_2,
542 					    WM8994_OPCLK_DIV_MASK, i);
543 			ret |= wm8994_bic_or(priv, WM8994_POWER_MANAGEMENT_2,
544 					     WM8994_OPCLK_ENA,
545 					     WM8994_OPCLK_ENA);
546 		} else {
547 			ret |= wm8994_bic_or(priv, WM8994_POWER_MANAGEMENT_2,
548 					     WM8994_OPCLK_ENA, 0);
549 		}
550 
551 	default:
552 		debug("%s Invalid input clock selection [%d]\n",
553 		      __func__, clk_id);
554 		return -1;
555 	}
556 
557 	ret |= configure_aif_clock(priv, aif_id);
558 
559 	if (ret < 0) {
560 		debug("%s: codec register access error\n", __func__);
561 		return -1;
562 	}
563 
564 	return 0;
565 }
566 
567 /*
568  * Initializes Volume for AIF2 to HP path
569  *
570  * @param priv		wm8994 information
571  * @returns -1 for error  and 0 Success.
572  *
573  */
574 static int wm8994_init_volume_aif2_dac1(struct wm8994_priv *priv)
575 {
576 	int ret;
577 
578 	/* Unmute AIF2DAC */
579 	ret = wm8994_bic_or(priv, WM8994_AIF2_DAC_FILTERS_1,
580 			    WM8994_AIF2DAC_MUTE_MASK, 0);
581 
582 
583 	ret |= wm8994_bic_or(priv, WM8994_AIF2_DAC_LEFT_VOLUME,
584 			     WM8994_AIF2DAC_VU_MASK | WM8994_AIF2DACL_VOL_MASK,
585 			     WM8994_AIF2DAC_VU | 0xff);
586 
587 	ret |= wm8994_bic_or(priv, WM8994_AIF2_DAC_RIGHT_VOLUME,
588 			     WM8994_AIF2DAC_VU_MASK | WM8994_AIF2DACR_VOL_MASK,
589 			     WM8994_AIF2DAC_VU | 0xff);
590 
591 
592 	ret |= wm8994_bic_or(priv, WM8994_DAC1_LEFT_VOLUME,
593 			     WM8994_DAC1_VU_MASK | WM8994_DAC1L_VOL_MASK |
594 			     WM8994_DAC1L_MUTE_MASK, WM8994_DAC1_VU | 0xc0);
595 
596 	ret |= wm8994_bic_or(priv, WM8994_DAC1_RIGHT_VOLUME,
597 			     WM8994_DAC1_VU_MASK | WM8994_DAC1R_VOL_MASK |
598 			     WM8994_DAC1R_MUTE_MASK, WM8994_DAC1_VU | 0xc0);
599 	/* Head Phone Volume */
600 	ret |= wm8994_i2c_write(priv, WM8994_LEFT_OUTPUT_VOLUME, 0x12D);
601 	ret |= wm8994_i2c_write(priv, WM8994_RIGHT_OUTPUT_VOLUME, 0x12D);
602 
603 	if (ret < 0) {
604 		debug("%s: codec register access error\n", __func__);
605 		return -1;
606 	}
607 
608 	return 0;
609 }
610 
611 /*
612  * Initializes Volume for AIF1 to HP path
613  *
614  * @param priv		wm8994 information
615  * @returns -1 for error  and 0 Success.
616  *
617  */
618 static int wm8994_init_volume_aif1_dac1(struct wm8994_priv *priv)
619 {
620 	int ret = 0;
621 
622 	/* Unmute AIF1DAC */
623 	ret |= wm8994_i2c_write(priv, WM8994_AIF1_DAC_FILTERS_1, 0x0000);
624 
625 	ret |= wm8994_bic_or(priv, WM8994_DAC1_LEFT_VOLUME,
626 			     WM8994_DAC1_VU_MASK | WM8994_DAC1L_VOL_MASK |
627 			     WM8994_DAC1L_MUTE_MASK, WM8994_DAC1_VU | 0xc0);
628 
629 	ret |= wm8994_bic_or(priv, WM8994_DAC1_RIGHT_VOLUME,
630 			     WM8994_DAC1_VU_MASK | WM8994_DAC1R_VOL_MASK |
631 			     WM8994_DAC1R_MUTE_MASK, WM8994_DAC1_VU | 0xc0);
632 	/* Head Phone Volume */
633 	ret |= wm8994_i2c_write(priv, WM8994_LEFT_OUTPUT_VOLUME, 0x12D);
634 	ret |= wm8994_i2c_write(priv, WM8994_RIGHT_OUTPUT_VOLUME, 0x12D);
635 
636 	if (ret < 0) {
637 		debug("%s: codec register access error\n", __func__);
638 		return -1;
639 	}
640 
641 	return 0;
642 }
643 
644 /*
645  * Intialise wm8994 codec device
646  *
647  * @param priv		wm8994 information
648  *
649  * @returns -1 for error  and 0 Success.
650  */
651 static int wm8994_device_init(struct wm8994_priv *priv)
652 {
653 	const char *devname;
654 	unsigned short reg_data;
655 	int ret;
656 
657 	wm8994_i2c_write(priv, WM8994_SOFTWARE_RESET, WM8994_SW_RESET);
658 
659 	ret = wm8994_i2c_read(priv, WM8994_SOFTWARE_RESET, &reg_data);
660 	if (ret < 0) {
661 		debug("Failed to read ID register\n");
662 		return ret;
663 	}
664 
665 	if (reg_data == WM8994_ID) {
666 		devname = "WM8994";
667 		debug("Device registered as type %d\n", priv->type);
668 		priv->type = WM8994;
669 	} else {
670 		debug("Device is not a WM8994, ID is %x\n", ret);
671 		return -ENXIO;
672 	}
673 
674 	ret = wm8994_i2c_read(priv, WM8994_CHIP_REVISION, &reg_data);
675 	if (ret < 0) {
676 		debug("Failed to read revision register: %d\n", ret);
677 		return ret;
678 	}
679 	priv->revision = reg_data;
680 	debug("%s revision %c\n", devname, 'A' + priv->revision);
681 
682 	return 0;
683 }
684 
685 static int wm8994_setup_interface(struct wm8994_priv *priv,
686 				  enum en_audio_interface aif_id)
687 {
688 	int ret;
689 
690 	/* VMID Selection */
691 	ret = wm8994_bic_or(priv, WM8994_POWER_MANAGEMENT_1,
692 			    WM8994_VMID_SEL_MASK | WM8994_BIAS_ENA_MASK, 0x3);
693 
694 	/* Charge Pump Enable */
695 	ret |= wm8994_bic_or(priv, WM8994_CHARGE_PUMP_1, WM8994_CP_ENA_MASK,
696 			     WM8994_CP_ENA);
697 
698 	/* Head Phone Power Enable */
699 	ret |= wm8994_bic_or(priv, WM8994_POWER_MANAGEMENT_1,
700 			     WM8994_HPOUT1L_ENA_MASK, WM8994_HPOUT1L_ENA);
701 
702 	ret |= wm8994_bic_or(priv, WM8994_POWER_MANAGEMENT_1,
703 			     WM8994_HPOUT1R_ENA_MASK, WM8994_HPOUT1R_ENA);
704 
705 	if (aif_id == WM8994_AIF1) {
706 		ret |= wm8994_i2c_write(priv, WM8994_POWER_MANAGEMENT_2,
707 					WM8994_TSHUT_ENA | WM8994_MIXINL_ENA |
708 					WM8994_MIXINR_ENA | WM8994_IN2L_ENA |
709 					WM8994_IN2R_ENA);
710 
711 		ret |= wm8994_i2c_write(priv, WM8994_POWER_MANAGEMENT_4,
712 					WM8994_ADCL_ENA | WM8994_ADCR_ENA |
713 					WM8994_AIF1ADC1R_ENA |
714 					WM8994_AIF1ADC1L_ENA);
715 
716 		/* Power enable for AIF1 and DAC1 */
717 		ret |= wm8994_i2c_write(priv, WM8994_POWER_MANAGEMENT_5,
718 					WM8994_AIF1DACL_ENA |
719 					WM8994_AIF1DACR_ENA |
720 					WM8994_DAC1L_ENA | WM8994_DAC1R_ENA);
721 	} else if (aif_id == WM8994_AIF2) {
722 		/* Power enable for AIF2 and DAC1 */
723 		ret |= wm8994_bic_or(priv, WM8994_POWER_MANAGEMENT_5,
724 			WM8994_AIF2DACL_ENA_MASK | WM8994_AIF2DACR_ENA_MASK |
725 			WM8994_DAC1L_ENA_MASK | WM8994_DAC1R_ENA_MASK,
726 			WM8994_AIF2DACL_ENA | WM8994_AIF2DACR_ENA |
727 			WM8994_DAC1L_ENA | WM8994_DAC1R_ENA);
728 	}
729 	/* Head Phone Initialisation */
730 	ret |= wm8994_bic_or(priv, WM8994_ANALOGUE_HP_1,
731 		WM8994_HPOUT1L_DLY_MASK | WM8994_HPOUT1R_DLY_MASK,
732 		WM8994_HPOUT1L_DLY | WM8994_HPOUT1R_DLY);
733 
734 	ret |= wm8994_bic_or(priv, WM8994_DC_SERVO_1,
735 			WM8994_DCS_ENA_CHAN_0_MASK |
736 			WM8994_DCS_ENA_CHAN_1_MASK , WM8994_DCS_ENA_CHAN_0 |
737 			WM8994_DCS_ENA_CHAN_1);
738 
739 	ret |= wm8994_bic_or(priv, WM8994_ANALOGUE_HP_1,
740 			WM8994_HPOUT1L_DLY_MASK |
741 			WM8994_HPOUT1R_DLY_MASK | WM8994_HPOUT1L_OUTP_MASK |
742 			WM8994_HPOUT1R_OUTP_MASK |
743 			WM8994_HPOUT1L_RMV_SHORT_MASK |
744 			WM8994_HPOUT1R_RMV_SHORT_MASK, WM8994_HPOUT1L_DLY |
745 			WM8994_HPOUT1R_DLY | WM8994_HPOUT1L_OUTP |
746 			WM8994_HPOUT1R_OUTP | WM8994_HPOUT1L_RMV_SHORT |
747 			WM8994_HPOUT1R_RMV_SHORT);
748 
749 	/* MIXER Config DAC1 to HP */
750 	ret |= wm8994_bic_or(priv, WM8994_OUTPUT_MIXER_1,
751 			     WM8994_DAC1L_TO_HPOUT1L_MASK,
752 			     WM8994_DAC1L_TO_HPOUT1L);
753 
754 	ret |= wm8994_bic_or(priv, WM8994_OUTPUT_MIXER_2,
755 			     WM8994_DAC1R_TO_HPOUT1R_MASK,
756 			     WM8994_DAC1R_TO_HPOUT1R);
757 
758 	if (aif_id == WM8994_AIF1) {
759 		/* Routing AIF1 to DAC1 */
760 		ret |= wm8994_i2c_write(priv, WM8994_DAC1_LEFT_MIXER_ROUTING,
761 					WM8994_AIF1DAC1L_TO_DAC1L);
762 
763 		ret |= wm8994_i2c_write(priv, WM8994_DAC1_RIGHT_MIXER_ROUTING,
764 					WM8994_AIF1DAC1R_TO_DAC1R);
765 
766 		/* GPIO Settings for AIF1 */
767 		ret |=  wm8994_i2c_write(priv, WM8994_GPIO_1,
768 					 WM8994_GPIO_DIR_OUTPUT |
769 					 WM8994_GPIO_FUNCTION_I2S_CLK |
770 					 WM8994_GPIO_INPUT_DEBOUNCE);
771 
772 		ret |= wm8994_init_volume_aif1_dac1(priv);
773 	} else if (aif_id == WM8994_AIF2) {
774 		/* Routing AIF2 to DAC1 */
775 		ret |= wm8994_bic_or(priv, WM8994_DAC1_LEFT_MIXER_ROUTING,
776 				     WM8994_AIF2DACL_TO_DAC1L_MASK,
777 				     WM8994_AIF2DACL_TO_DAC1L);
778 
779 		ret |= wm8994_bic_or(priv, WM8994_DAC1_RIGHT_MIXER_ROUTING,
780 				     WM8994_AIF2DACR_TO_DAC1R_MASK,
781 				     WM8994_AIF2DACR_TO_DAC1R);
782 
783 		/* GPIO Settings for AIF2 */
784 		/* B CLK */
785 		ret |= wm8994_bic_or(priv, WM8994_GPIO_3, WM8994_GPIO_DIR_MASK |
786 				     WM8994_GPIO_FUNCTION_MASK,
787 				     WM8994_GPIO_DIR_OUTPUT);
788 
789 		/* LR CLK */
790 		ret |= wm8994_bic_or(priv, WM8994_GPIO_4, WM8994_GPIO_DIR_MASK |
791 				     WM8994_GPIO_FUNCTION_MASK,
792 				     WM8994_GPIO_DIR_OUTPUT);
793 
794 		/* DATA */
795 		ret |= wm8994_bic_or(priv, WM8994_GPIO_5, WM8994_GPIO_DIR_MASK |
796 				     WM8994_GPIO_FUNCTION_MASK,
797 				     WM8994_GPIO_DIR_OUTPUT);
798 
799 		ret |= wm8994_init_volume_aif2_dac1(priv);
800 	}
801 
802 	if (ret < 0)
803 		goto err;
804 
805 	debug("%s: Codec chip setup ok\n", __func__);
806 	return 0;
807 err:
808 	debug("%s: Codec chip setup error\n", __func__);
809 	return -1;
810 }
811 
812 static int _wm8994_init(struct wm8994_priv *priv,
813 			enum en_audio_interface aif_id, int sampling_rate,
814 			int mclk_freq, int bits_per_sample,
815 			unsigned int channels)
816 {
817 	int ret;
818 
819 	ret = wm8994_setup_interface(priv, aif_id);
820 	if (ret < 0) {
821 		debug("%s: wm8994 codec chip init failed\n", __func__);
822 		return ret;
823 	}
824 
825 	ret = wm8994_set_sysclk(priv, aif_id, WM8994_SYSCLK_MCLK1, mclk_freq);
826 	if (ret < 0) {
827 		debug("%s: wm8994 codec set sys clock failed\n", __func__);
828 		return ret;
829 	}
830 
831 	ret = wm8994_hw_params(priv, aif_id, sampling_rate, bits_per_sample,
832 			       channels);
833 
834 	if (ret == 0) {
835 		ret = wm8994_set_fmt(priv, aif_id, SND_SOC_DAIFMT_I2S |
836 				     SND_SOC_DAIFMT_NB_NF |
837 				     SND_SOC_DAIFMT_CBS_CFS);
838 	}
839 
840 	return ret;
841 }
842 
843 static int wm8994_set_params(struct udevice *dev, int interface, int rate,
844 			     int mclk_freq, int bits_per_sample, uint channels)
845 {
846 	struct wm8994_priv *priv = dev_get_priv(dev);
847 
848 	return _wm8994_init(priv, interface, rate, mclk_freq, bits_per_sample,
849 			    channels);
850 }
851 
852 static int wm8994_probe(struct udevice *dev)
853 {
854 	struct wm8994_priv *priv = dev_get_priv(dev);
855 
856 	priv->dev = dev;
857 	return wm8994_device_init(priv);
858 }
859 
860 static const struct audio_codec_ops wm8994_ops = {
861 	.set_params	= wm8994_set_params,
862 };
863 
864 static const struct udevice_id wm8994_ids[] = {
865 	{ .compatible = "wolfson,wm8994" },
866 	{ }
867 };
868 
869 U_BOOT_DRIVER(wm8994) = {
870 	.name		= "wm8994",
871 	.id		= UCLASS_AUDIO_CODEC,
872 	.of_match	= wm8994_ids,
873 	.probe		= wm8994_probe,
874 	.ops		= &wm8994_ops,
875 	.priv_auto_alloc_size	= sizeof(struct wm8994_priv),
876 };
877