1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * (C) Copyright 2009 SAMSUNG Electronics 4 * Minkyu Kang <mk7.kang@samsung.com> 5 * Heungjun Kim <riverful.kim@samsung.com> 6 * 7 * based on drivers/serial/s3c64xx.c 8 */ 9 10 #include <common.h> 11 #include <dm.h> 12 #include <errno.h> 13 #include <fdtdec.h> 14 #include <linux/compiler.h> 15 #include <asm/io.h> 16 #include <asm/arch/clk.h> 17 #include <asm/arch/uart.h> 18 #include <serial.h> 19 #include <clk.h> 20 21 DECLARE_GLOBAL_DATA_PTR; 22 23 #define RX_FIFO_COUNT_SHIFT 0 24 #define RX_FIFO_COUNT_MASK (0xff << RX_FIFO_COUNT_SHIFT) 25 #define RX_FIFO_FULL (1 << 8) 26 #define TX_FIFO_COUNT_SHIFT 16 27 #define TX_FIFO_COUNT_MASK (0xff << TX_FIFO_COUNT_SHIFT) 28 #define TX_FIFO_FULL (1 << 24) 29 30 /* Information about a serial port */ 31 struct s5p_serial_platdata { 32 struct s5p_uart *reg; /* address of registers in physical memory */ 33 u8 port_id; /* uart port number */ 34 }; 35 36 /* 37 * The coefficient, used to calculate the baudrate on S5P UARTs is 38 * calculated as 39 * C = UBRDIV * 16 + number_of_set_bits_in_UDIVSLOT 40 * however, section 31.6.11 of the datasheet doesn't recomment using 1 for 1, 41 * 3 for 2, ... (2^n - 1) for n, instead, they suggest using these constants: 42 */ 43 static const int udivslot[] = { 44 0, 45 0x0080, 46 0x0808, 47 0x0888, 48 0x2222, 49 0x4924, 50 0x4a52, 51 0x54aa, 52 0x5555, 53 0xd555, 54 0xd5d5, 55 0xddd5, 56 0xdddd, 57 0xdfdd, 58 0xdfdf, 59 0xffdf, 60 }; 61 62 static void __maybe_unused s5p_serial_init(struct s5p_uart *uart) 63 { 64 /* enable FIFOs, auto clear Rx FIFO */ 65 writel(0x3, &uart->ufcon); 66 writel(0, &uart->umcon); 67 /* 8N1 */ 68 writel(0x3, &uart->ulcon); 69 /* No interrupts, no DMA, pure polling */ 70 writel(0x245, &uart->ucon); 71 } 72 73 static void __maybe_unused s5p_serial_baud(struct s5p_uart *uart, uint uclk, 74 int baudrate) 75 { 76 u32 val; 77 78 val = uclk / baudrate; 79 80 writel(val / 16 - 1, &uart->ubrdiv); 81 82 if (s5p_uart_divslot()) 83 writew(udivslot[val % 16], &uart->rest.slot); 84 else 85 writeb(val % 16, &uart->rest.value); 86 } 87 88 #ifndef CONFIG_SPL_BUILD 89 int s5p_serial_setbrg(struct udevice *dev, int baudrate) 90 { 91 struct s5p_serial_platdata *plat = dev->platdata; 92 struct s5p_uart *const uart = plat->reg; 93 u32 uclk; 94 95 #ifdef CONFIG_CLK_EXYNOS 96 struct clk clk; 97 u32 ret; 98 99 ret = clk_get_by_index(dev, 1, &clk); 100 if (ret < 0) 101 return ret; 102 uclk = clk_get_rate(&clk); 103 #else 104 uclk = get_uart_clk(plat->port_id); 105 #endif 106 107 s5p_serial_baud(uart, uclk, baudrate); 108 109 return 0; 110 } 111 112 static int s5p_serial_probe(struct udevice *dev) 113 { 114 struct s5p_serial_platdata *plat = dev->platdata; 115 struct s5p_uart *const uart = plat->reg; 116 117 s5p_serial_init(uart); 118 119 return 0; 120 } 121 122 static int serial_err_check(const struct s5p_uart *const uart, int op) 123 { 124 unsigned int mask; 125 126 /* 127 * UERSTAT 128 * Break Detect [3] 129 * Frame Err [2] : receive operation 130 * Parity Err [1] : receive operation 131 * Overrun Err [0] : receive operation 132 */ 133 if (op) 134 mask = 0x8; 135 else 136 mask = 0xf; 137 138 return readl(&uart->uerstat) & mask; 139 } 140 141 static int s5p_serial_getc(struct udevice *dev) 142 { 143 struct s5p_serial_platdata *plat = dev->platdata; 144 struct s5p_uart *const uart = plat->reg; 145 146 if (!(readl(&uart->ufstat) & RX_FIFO_COUNT_MASK)) 147 return -EAGAIN; 148 149 serial_err_check(uart, 0); 150 return (int)(readb(&uart->urxh) & 0xff); 151 } 152 153 static int s5p_serial_putc(struct udevice *dev, const char ch) 154 { 155 struct s5p_serial_platdata *plat = dev->platdata; 156 struct s5p_uart *const uart = plat->reg; 157 158 if (readl(&uart->ufstat) & TX_FIFO_FULL) 159 return -EAGAIN; 160 161 writeb(ch, &uart->utxh); 162 serial_err_check(uart, 1); 163 164 return 0; 165 } 166 167 static int s5p_serial_pending(struct udevice *dev, bool input) 168 { 169 struct s5p_serial_platdata *plat = dev->platdata; 170 struct s5p_uart *const uart = plat->reg; 171 uint32_t ufstat = readl(&uart->ufstat); 172 173 if (input) 174 return (ufstat & RX_FIFO_COUNT_MASK) >> RX_FIFO_COUNT_SHIFT; 175 else 176 return (ufstat & TX_FIFO_COUNT_MASK) >> TX_FIFO_COUNT_SHIFT; 177 } 178 179 static int s5p_serial_ofdata_to_platdata(struct udevice *dev) 180 { 181 struct s5p_serial_platdata *plat = dev->platdata; 182 fdt_addr_t addr; 183 184 addr = devfdt_get_addr(dev); 185 if (addr == FDT_ADDR_T_NONE) 186 return -EINVAL; 187 188 plat->reg = (struct s5p_uart *)addr; 189 plat->port_id = fdtdec_get_int(gd->fdt_blob, dev_of_offset(dev), 190 "id", dev->seq); 191 return 0; 192 } 193 194 static const struct dm_serial_ops s5p_serial_ops = { 195 .putc = s5p_serial_putc, 196 .pending = s5p_serial_pending, 197 .getc = s5p_serial_getc, 198 .setbrg = s5p_serial_setbrg, 199 }; 200 201 static const struct udevice_id s5p_serial_ids[] = { 202 { .compatible = "samsung,exynos4210-uart" }, 203 { } 204 }; 205 206 U_BOOT_DRIVER(serial_s5p) = { 207 .name = "serial_s5p", 208 .id = UCLASS_SERIAL, 209 .of_match = s5p_serial_ids, 210 .ofdata_to_platdata = s5p_serial_ofdata_to_platdata, 211 .platdata_auto_alloc_size = sizeof(struct s5p_serial_platdata), 212 .probe = s5p_serial_probe, 213 .ops = &s5p_serial_ops, 214 .flags = DM_FLAG_PRE_RELOC, 215 }; 216 #endif 217 218 #ifdef CONFIG_DEBUG_UART_S5P 219 220 #include <debug_uart.h> 221 222 static inline void _debug_uart_init(void) 223 { 224 struct s5p_uart *uart = (struct s5p_uart *)CONFIG_DEBUG_UART_BASE; 225 226 s5p_serial_init(uart); 227 s5p_serial_baud(uart, CONFIG_DEBUG_UART_CLOCK, CONFIG_BAUDRATE); 228 } 229 230 static inline void _debug_uart_putc(int ch) 231 { 232 struct s5p_uart *uart = (struct s5p_uart *)CONFIG_DEBUG_UART_BASE; 233 234 while (readl(&uart->ufstat) & TX_FIFO_FULL); 235 236 writeb(ch, &uart->utxh); 237 } 238 239 DEBUG_UART_FUNCS 240 241 #endif 242