1 /* 2 * (c) 2007 Sascha Hauer <s.hauer@pengutronix.de> 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #include <common.h> 8 #include <watchdog.h> 9 #include <asm/arch/imx-regs.h> 10 #include <asm/arch/clock.h> 11 #include <serial.h> 12 #include <linux/compiler.h> 13 14 #define __REG(x) (*((volatile u32 *)(x))) 15 16 #ifndef CONFIG_MXC_UART_BASE 17 #error "define CONFIG_MXC_UART_BASE to use the MXC UART driver" 18 #endif 19 20 #define UART_PHYS CONFIG_MXC_UART_BASE 21 22 /* Register definitions */ 23 #define URXD 0x0 /* Receiver Register */ 24 #define UTXD 0x40 /* Transmitter Register */ 25 #define UCR1 0x80 /* Control Register 1 */ 26 #define UCR2 0x84 /* Control Register 2 */ 27 #define UCR3 0x88 /* Control Register 3 */ 28 #define UCR4 0x8c /* Control Register 4 */ 29 #define UFCR 0x90 /* FIFO Control Register */ 30 #define USR1 0x94 /* Status Register 1 */ 31 #define USR2 0x98 /* Status Register 2 */ 32 #define UESC 0x9c /* Escape Character Register */ 33 #define UTIM 0xa0 /* Escape Timer Register */ 34 #define UBIR 0xa4 /* BRM Incremental Register */ 35 #define UBMR 0xa8 /* BRM Modulator Register */ 36 #define UBRC 0xac /* Baud Rate Count Register */ 37 #define UTS 0xb4 /* UART Test Register (mx31) */ 38 39 /* UART Control Register Bit Fields.*/ 40 #define URXD_CHARRDY (1<<15) 41 #define URXD_ERR (1<<14) 42 #define URXD_OVRRUN (1<<13) 43 #define URXD_FRMERR (1<<12) 44 #define URXD_BRK (1<<11) 45 #define URXD_PRERR (1<<10) 46 #define URXD_RX_DATA (0xFF) 47 #define UCR1_ADEN (1<<15) /* Auto dectect interrupt */ 48 #define UCR1_ADBR (1<<14) /* Auto detect baud rate */ 49 #define UCR1_TRDYEN (1<<13) /* Transmitter ready interrupt enable */ 50 #define UCR1_IDEN (1<<12) /* Idle condition interrupt */ 51 #define UCR1_RRDYEN (1<<9) /* Recv ready interrupt enable */ 52 #define UCR1_RDMAEN (1<<8) /* Recv ready DMA enable */ 53 #define UCR1_IREN (1<<7) /* Infrared interface enable */ 54 #define UCR1_TXMPTYEN (1<<6) /* Transimitter empty interrupt enable */ 55 #define UCR1_RTSDEN (1<<5) /* RTS delta interrupt enable */ 56 #define UCR1_SNDBRK (1<<4) /* Send break */ 57 #define UCR1_TDMAEN (1<<3) /* Transmitter ready DMA enable */ 58 #define UCR1_UARTCLKEN (1<<2) /* UART clock enabled */ 59 #define UCR1_DOZE (1<<1) /* Doze */ 60 #define UCR1_UARTEN (1<<0) /* UART enabled */ 61 #define UCR2_ESCI (1<<15) /* Escape seq interrupt enable */ 62 #define UCR2_IRTS (1<<14) /* Ignore RTS pin */ 63 #define UCR2_CTSC (1<<13) /* CTS pin control */ 64 #define UCR2_CTS (1<<12) /* Clear to send */ 65 #define UCR2_ESCEN (1<<11) /* Escape enable */ 66 #define UCR2_PREN (1<<8) /* Parity enable */ 67 #define UCR2_PROE (1<<7) /* Parity odd/even */ 68 #define UCR2_STPB (1<<6) /* Stop */ 69 #define UCR2_WS (1<<5) /* Word size */ 70 #define UCR2_RTSEN (1<<4) /* Request to send interrupt enable */ 71 #define UCR2_TXEN (1<<2) /* Transmitter enabled */ 72 #define UCR2_RXEN (1<<1) /* Receiver enabled */ 73 #define UCR2_SRST (1<<0) /* SW reset */ 74 #define UCR3_DTREN (1<<13) /* DTR interrupt enable */ 75 #define UCR3_PARERREN (1<<12) /* Parity enable */ 76 #define UCR3_FRAERREN (1<<11) /* Frame error interrupt enable */ 77 #define UCR3_DSR (1<<10) /* Data set ready */ 78 #define UCR3_DCD (1<<9) /* Data carrier detect */ 79 #define UCR3_RI (1<<8) /* Ring indicator */ 80 #define UCR3_TIMEOUTEN (1<<7) /* Timeout interrupt enable */ 81 #define UCR3_RXDSEN (1<<6) /* Receive status interrupt enable */ 82 #define UCR3_AIRINTEN (1<<5) /* Async IR wake interrupt enable */ 83 #define UCR3_AWAKEN (1<<4) /* Async wake interrupt enable */ 84 #define UCR3_REF25 (1<<3) /* Ref freq 25 MHz */ 85 #define UCR3_REF30 (1<<2) /* Ref Freq 30 MHz */ 86 #define UCR3_INVT (1<<1) /* Inverted Infrared transmission */ 87 #define UCR3_BPEN (1<<0) /* Preset registers enable */ 88 #define UCR4_CTSTL_32 (32<<10) /* CTS trigger level (32 chars) */ 89 #define UCR4_INVR (1<<9) /* Inverted infrared reception */ 90 #define UCR4_ENIRI (1<<8) /* Serial infrared interrupt enable */ 91 #define UCR4_WKEN (1<<7) /* Wake interrupt enable */ 92 #define UCR4_REF16 (1<<6) /* Ref freq 16 MHz */ 93 #define UCR4_IRSC (1<<5) /* IR special case */ 94 #define UCR4_TCEN (1<<3) /* Transmit complete interrupt enable */ 95 #define UCR4_BKEN (1<<2) /* Break condition interrupt enable */ 96 #define UCR4_OREN (1<<1) /* Receiver overrun interrupt enable */ 97 #define UCR4_DREN (1<<0) /* Recv data ready interrupt enable */ 98 #define UFCR_RXTL_SHF 0 /* Receiver trigger level shift */ 99 #define UFCR_RFDIV (7<<7) /* Reference freq divider mask */ 100 #define UFCR_TXTL_SHF 10 /* Transmitter trigger level shift */ 101 #define USR1_PARITYERR (1<<15) /* Parity error interrupt flag */ 102 #define USR1_RTSS (1<<14) /* RTS pin status */ 103 #define USR1_TRDY (1<<13) /* Transmitter ready interrupt/dma flag */ 104 #define USR1_RTSD (1<<12) /* RTS delta */ 105 #define USR1_ESCF (1<<11) /* Escape seq interrupt flag */ 106 #define USR1_FRAMERR (1<<10) /* Frame error interrupt flag */ 107 #define USR1_RRDY (1<<9) /* Receiver ready interrupt/dma flag */ 108 #define USR1_TIMEOUT (1<<7) /* Receive timeout interrupt status */ 109 #define USR1_RXDS (1<<6) /* Receiver idle interrupt flag */ 110 #define USR1_AIRINT (1<<5) /* Async IR wake interrupt flag */ 111 #define USR1_AWAKE (1<<4) /* Aysnc wake interrupt flag */ 112 #define USR2_ADET (1<<15) /* Auto baud rate detect complete */ 113 #define USR2_TXFE (1<<14) /* Transmit buffer FIFO empty */ 114 #define USR2_DTRF (1<<13) /* DTR edge interrupt flag */ 115 #define USR2_IDLE (1<<12) /* Idle condition */ 116 #define USR2_IRINT (1<<8) /* Serial infrared interrupt flag */ 117 #define USR2_WAKE (1<<7) /* Wake */ 118 #define USR2_RTSF (1<<4) /* RTS edge interrupt flag */ 119 #define USR2_TXDC (1<<3) /* Transmitter complete */ 120 #define USR2_BRCD (1<<2) /* Break condition */ 121 #define USR2_ORE (1<<1) /* Overrun error */ 122 #define USR2_RDR (1<<0) /* Recv data ready */ 123 #define UTS_FRCPERR (1<<13) /* Force parity error */ 124 #define UTS_LOOP (1<<12) /* Loop tx and rx */ 125 #define UTS_TXEMPTY (1<<6) /* TxFIFO empty */ 126 #define UTS_RXEMPTY (1<<5) /* RxFIFO empty */ 127 #define UTS_TXFULL (1<<4) /* TxFIFO full */ 128 #define UTS_RXFULL (1<<3) /* RxFIFO full */ 129 #define UTS_SOFTRST (1<<0) /* Software reset */ 130 131 DECLARE_GLOBAL_DATA_PTR; 132 133 static void mxc_serial_setbrg(void) 134 { 135 u32 clk = imx_get_uartclk(); 136 137 if (!gd->baudrate) 138 gd->baudrate = CONFIG_BAUDRATE; 139 140 __REG(UART_PHYS + UFCR) = 4 << 7; /* divide input clock by 2 */ 141 __REG(UART_PHYS + UBIR) = 0xf; 142 __REG(UART_PHYS + UBMR) = clk / (2 * gd->baudrate); 143 144 } 145 146 static int mxc_serial_getc(void) 147 { 148 while (__REG(UART_PHYS + UTS) & UTS_RXEMPTY) 149 WATCHDOG_RESET(); 150 return (__REG(UART_PHYS + URXD) & URXD_RX_DATA); /* mask out status from upper word */ 151 } 152 153 static void mxc_serial_putc(const char c) 154 { 155 __REG(UART_PHYS + UTXD) = c; 156 157 /* wait for transmitter to be ready */ 158 while (!(__REG(UART_PHYS + UTS) & UTS_TXEMPTY)) 159 WATCHDOG_RESET(); 160 161 /* If \n, also do \r */ 162 if (c == '\n') 163 serial_putc ('\r'); 164 } 165 166 /* 167 * Test whether a character is in the RX buffer 168 */ 169 static int mxc_serial_tstc(void) 170 { 171 /* If receive fifo is empty, return false */ 172 if (__REG(UART_PHYS + UTS) & UTS_RXEMPTY) 173 return 0; 174 return 1; 175 } 176 177 /* 178 * Initialise the serial port with the given baudrate. The settings 179 * are always 8 data bits, no parity, 1 stop bit, no start bits. 180 * 181 */ 182 static int mxc_serial_init(void) 183 { 184 __REG(UART_PHYS + UCR1) = 0x0; 185 __REG(UART_PHYS + UCR2) = 0x0; 186 187 while (!(__REG(UART_PHYS + UCR2) & UCR2_SRST)); 188 189 __REG(UART_PHYS + UCR3) = 0x0704; 190 __REG(UART_PHYS + UCR4) = 0x8000; 191 __REG(UART_PHYS + UESC) = 0x002b; 192 __REG(UART_PHYS + UTIM) = 0x0; 193 194 __REG(UART_PHYS + UTS) = 0x0; 195 196 serial_setbrg(); 197 198 __REG(UART_PHYS + UCR2) = UCR2_WS | UCR2_IRTS | UCR2_RXEN | UCR2_TXEN | UCR2_SRST; 199 200 __REG(UART_PHYS + UCR1) = UCR1_UARTEN; 201 202 return 0; 203 } 204 205 static struct serial_device mxc_serial_drv = { 206 .name = "mxc_serial", 207 .start = mxc_serial_init, 208 .stop = NULL, 209 .setbrg = mxc_serial_setbrg, 210 .putc = mxc_serial_putc, 211 .puts = default_serial_puts, 212 .getc = mxc_serial_getc, 213 .tstc = mxc_serial_tstc, 214 }; 215 216 void mxc_serial_initialize(void) 217 { 218 serial_register(&mxc_serial_drv); 219 } 220 221 __weak struct serial_device *default_serial_console(void) 222 { 223 return &mxc_serial_drv; 224 } 225