1# 2# Serial device configuration 3# 4 5menu "Serial drivers" 6 7config REQUIRE_SERIAL_CONSOLE 8 bool "Require a serial port for console" 9 # Running without a serial console is not supported by the 10 # non-dm serial code 11 depends on DM_SERIAL 12 default y 13 help 14 Require a serial port for the console, and panic if none is found 15 during serial port initialization (default y). Set this to n on 16 boards which have no debug serial port whatsoever. 17 18config SERIAL_PRESENT 19 bool "Provide a serial driver" 20 depends on DM_SERIAL 21 default y 22 help 23 In very space-constrained devices even the full UART driver is too 24 large. In this case the debug UART can still be used in some cases. 25 This option enables the full UART in U-Boot, so if is it disabled, 26 the full UART driver will be omitted, thus saving space. 27 28config SPL_SERIAL_PRESENT 29 bool "Provide a serial driver in SPL" 30 depends on DM_SERIAL 31 default y 32 help 33 In very space-constrained devices even the full UART driver is too 34 large. In this case the debug UART can still be used in some cases. 35 This option enables the full UART in SPL, so if is it disabled, 36 the full UART driver will be omitted, thus saving space. 37 38config DM_SERIAL 39 bool "Enable Driver Model for serial drivers" 40 depends on DM 41 help 42 Enable driver model for serial. This replaces 43 drivers/serial/serial.c with the serial uclass, which 44 implements serial_putc() etc. The uclass interface is 45 defined in include/serial.h. 46 47config DEBUG_UART 48 bool "Enable an early debug UART for debugging" 49 help 50 The debug UART is intended for use very early in U-Boot to debug 51 problems when an ICE or other debug mechanism is not available. 52 53 To use it you should: 54 - Make sure your UART supports this interface 55 - Enable CONFIG_DEBUG_UART 56 - Enable the CONFIG for your UART to tell it to provide this interface 57 (e.g. CONFIG_DEBUG_UART_NS16550) 58 - Define the required settings as needed (see below) 59 - Call debug_uart_init() before use 60 - Call debug_uart_putc() to output a character 61 62 Depending on your platform it may be possible to use this UART before 63 a stack is available. 64 65 If your UART does not support this interface you can probably add 66 support quite easily. Remember that you cannot use driver model and 67 it is preferred to use no stack. 68 69 You must not use this UART once driver model is working and the 70 serial drivers are up and running (done in serial_init()). Otherwise 71 the drivers may conflict and you will get strange output. 72 73choice 74 prompt "Select which UART will provide the debug UART" 75 depends on DEBUG_UART 76 default DEBUG_UART_NS16550 77 78config DEBUG_UART_ALTERA_JTAGUART 79 bool "Altera JTAG UART" 80 help 81 Select this to enable a debug UART using the altera_jtag_uart driver. 82 You will need to provide parameters to make this work. The driver will 83 be available until the real driver model serial is running. 84 85config DEBUG_UART_ALTERA_UART 86 bool "Altera UART" 87 help 88 Select this to enable a debug UART using the altera_uart driver. 89 You will need to provide parameters to make this work. The driver will 90 be available until the real driver model serial is running. 91 92config DEBUG_UART_AR933X 93 bool "QCA/Atheros ar933x" 94 depends on AR933X_UART 95 help 96 Select this to enable a debug UART using the ar933x uart driver. 97 You will need to provide parameters to make this work. The 98 driver will be available until the real driver model serial is 99 running. 100 101config DEBUG_UART_NS16550 102 bool "ns16550" 103 help 104 Select this to enable a debug UART using the ns16550 driver. You 105 will need to provide parameters to make this work. The driver will 106 be available until the real driver model serial is running. 107 108config DEBUG_EFI_CONSOLE 109 bool "EFI" 110 depends on EFI_APP 111 help 112 Select this to enable a debug console which calls back to EFI to 113 output to the console. This can be useful for early debugging of 114 U-Boot when running on top of EFI (Extensive Firmware Interface). 115 This is a type of BIOS used by PCs. 116 117config DEBUG_UART_S5P 118 bool "Samsung S5P" 119 help 120 Select this to enable a debug UART using the serial_s5p driver. You 121 will need to provide parameters to make this work. The driver will 122 be available until the real driver-model serial is running. 123 124config DEBUG_UART_MESON 125 bool "Amlogic Meson" 126 depends on MESON_SERIAL 127 help 128 Select this to enable a debug UART using the serial_meson driver. You 129 will need to provide parameters to make this work. The driver will 130 be available until the real driver-model serial is running. 131 132config DEBUG_UART_UARTLITE 133 bool "Xilinx Uartlite" 134 help 135 Select this to enable a debug UART using the serial_uartlite driver. 136 You will need to provide parameters to make this work. The driver will 137 be available until the real driver-model serial is running. 138 139config DEBUG_UART_ARM_DCC 140 bool "ARM DCC" 141 help 142 Select this to enable a debug UART using the ARM JTAG DCC port. 143 The DCC port can be used for very early debugging and doesn't require 144 any additional setting like address/baudrate/clock. On systems without 145 any serial interface this is the easiest way how to get console. 146 Every ARM core has own DCC port which is the part of debug interface. 147 This port is available at least on ARMv6, ARMv7, ARMv8 and XScale 148 architectures. 149 150config DEBUG_UART_ZYNQ 151 bool "Xilinx Zynq" 152 help 153 Select this to enable a debug UART using the serial_zynq driver. You 154 will need to provide parameters to make this work. The driver will 155 be available until the real driver-model serial is running. 156 157config DEBUG_UART_APBUART 158 depends on LEON3 159 bool "Gaisler APBUART" 160 help 161 Select this to enable a debug UART using the serial_leon3 driver. You 162 will need to provide parameters to make this work. The driver will 163 be available until the real driver model serial is running. 164 165config DEBUG_UART_PL010 166 bool "pl010" 167 help 168 Select this to enable a debug UART using the pl01x driver with the 169 PL010 UART type. You will need to provide parameters to make this 170 work. The driver will be available until the real driver model 171 serial is running. 172 173config DEBUG_UART_PL011 174 bool "pl011" 175 help 176 Select this to enable a debug UART using the pl01x driver with the 177 PL011 UART type. You will need to provide parameters to make this 178 work. The driver will be available until the real driver model 179 serial is running. 180 181config DEBUG_UART_PIC32 182 bool "Microchip PIC32" 183 depends on PIC32_SERIAL 184 help 185 Select this to enable a debug UART using the serial_pic32 driver. You 186 will need to provide parameters to make this work. The driver will 187 be available until the real driver model serial is running. 188 189config DEBUG_UART_UNIPHIER 190 bool "UniPhier on-chip UART" 191 depends on ARCH_UNIPHIER 192 help 193 Select this to enable a debug UART using the UniPhier on-chip UART. 194 You will need to provide DEBUG_UART_BASE to make this work. The 195 driver will be available until the real driver-model serial is 196 running. 197 198endchoice 199 200config DEBUG_UART_BASE 201 hex "Base address of UART" 202 depends on DEBUG_UART 203 help 204 This is the base address of your UART for memory-mapped UARTs. 205 206 A default should be provided by your board, but if not you will need 207 to use the correct value here. 208 209config DEBUG_UART_CLOCK 210 int "UART input clock" 211 depends on DEBUG_UART 212 help 213 The UART input clock determines the speed of the internal UART 214 circuitry. The baud rate is derived from this by dividing the input 215 clock down. 216 217 A default should be provided by your board, but if not you will need 218 to use the correct value here. 219 220config DEBUG_UART_SHIFT 221 int "UART register shift" 222 depends on DEBUG_UART 223 default 0 if DEBUG_UART 224 help 225 Some UARTs (notably ns16550) support different register layouts 226 where the registers are spaced either as bytes, words or some other 227 value. Use this value to specify the shift to use, where 0=byte 228 registers, 2=32-bit word registers, etc. 229 230config DEBUG_UART_BOARD_INIT 231 bool "Enable board-specific debug UART init" 232 depends on DEBUG_UART 233 help 234 Some boards need to set things up before the debug UART can be used. 235 On these boards a call to debug_uart_init() is insufficient. When 236 this option is enabled, the function board_debug_uart_init() will 237 be called when debug_uart_init() is called. You can put any code 238 here that is needed to set up the UART ready for use, such as set 239 pin multiplexing or enable clocks. 240 241config DEBUG_UART_ANNOUNCE 242 bool "Show a message when the debug UART starts up" 243 depends on DEBUG_UART 244 help 245 Enable this option to show a message when the debug UART is ready 246 for use. You will see a message like "<debug_uart> " as soon as 247 U-Boot has the UART ready for use (i.e. your code calls 248 debug_uart_init()). This can be useful just as a check that 249 everything is working. 250 251config DEBUG_UART_SKIP_INIT 252 bool "Skip UART initialization" 253 help 254 Select this if the UART you want to use for debug output is already 255 initialized by the time U-Boot starts its execution. 256 257config ALTERA_JTAG_UART 258 bool "Altera JTAG UART support" 259 depends on DM_SERIAL 260 help 261 Select this to enable an JTAG UART for Altera devices.The JTAG UART 262 core implements a method to communicate serial character streams 263 between a host PC and a Qsys system on an Altera FPGA. Please find 264 details on the "Embedded Peripherals IP User Guide" of Altera. 265 266config ALTERA_JTAG_UART_BYPASS 267 bool "Bypass output when no connection" 268 depends on ALTERA_JTAG_UART 269 help 270 Bypass console output and keep going even if there is no JTAG 271 terminal connection with the host. The console output will resume 272 once the JTAG terminal is connected. Without the bypass, the console 273 output will wait forever until a JTAG terminal is connected. If you 274 not are sure, say Y. 275 276config ALTERA_UART 277 bool "Altera UART support" 278 depends on DM_SERIAL 279 help 280 Select this to enable an UART for Altera devices. Please find 281 details on the "Embedded Peripherals IP User Guide" of Altera. 282 283config AR933X_UART 284 bool "QCA/Atheros ar933x UART support" 285 depends on DM_SERIAL && SOC_AR933X 286 help 287 Select this to enable UART support for QCA/Atheros ar933x 288 devices. This driver uses driver model and requires a device 289 tree binding to operate, please refer to the document at 290 doc/device-tree-bindings/serial/qca,ar9330-uart.txt. 291 292config FSL_LPUART 293 bool "Freescale LPUART support" 294 help 295 Select this to enable a Low Power UART for Freescale VF610 and 296 QorIQ Layerscape devices. 297 298config PIC32_SERIAL 299 bool "Support for Microchip PIC32 on-chip UART" 300 depends on DM_SERIAL && MACH_PIC32 301 default y 302 help 303 Support for the UART found on Microchip PIC32 SoC's. 304 305config SYS_NS16550 306 bool "NS16550 UART or compatible" 307 help 308 Support NS16550 UART or compatible. This can be enabled in the 309 device tree with the correct input clock frequency. If the input 310 clock frequency is not defined in the device tree, the macro 311 CONFIG_SYS_NS16550_CLK defined in a legacy board header file will 312 be used. It can be a constant or a function to get clock, eg, 313 get_serial_clock(). 314 315config ROCKCHIP_SERIAL 316 bool "Rockchip on-chip UART support" 317 depends on DM_SERIAL && SPL_OF_PLATDATA 318 help 319 Select this to enable a debug UART for Rockchip devices when using 320 CONFIG_OF_PLATDATA (i.e. a compiled-in device tree replacemenmt). 321 This uses the ns16550 driver, converting the platdata from of-platdata 322 to the ns16550 format. 323 324config SANDBOX_SERIAL 325 bool "Sandbox UART support" 326 depends on SANDBOX 327 help 328 Select this to enable a seral UART for sandbox. This is required to 329 operate correctly, otherwise you will see no serial output from 330 sandbox. The emulated UART will display to the console and console 331 input will be fed into the UART. This allows you to interact with 332 U-Boot. 333 334 The operation of the console is controlled by the -t command-line 335 flag. In raw mode, U-Boot sees all characters from the terminal 336 before they are processed, including Ctrl-C. In cooked mode, Ctrl-C 337 is processed by the terminal, and terminates U-Boot. Valid options 338 are: 339 340 -t raw-with-sigs Raw mode, Ctrl-C will terminate U-Boot 341 -t raw Raw mode, Ctrl-C is processed by U-Boot 342 -t cooked Cooked mode, Ctrl-C terminates 343 344config UNIPHIER_SERIAL 345 bool "Support for UniPhier on-chip UART" 346 depends on ARCH_UNIPHIER 347 help 348 If you have a UniPhier based board and want to use the on-chip 349 serial ports, say Y to this option. If unsure, say N. 350 351config XILINX_UARTLITE 352 bool "Xilinx Uarlite support" 353 depends on DM_SERIAL && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP || 4xx) 354 help 355 If you have a Xilinx based board and want to use the uartlite 356 serial ports, say Y to this option. If unsure, say N. 357 358config MESON_SERIAL 359 bool "Support for Amlogic Meson UART" 360 depends on DM_SERIAL && ARCH_MESON 361 help 362 If you have an Amlogic Meson based board and want to use the on-chip 363 serial ports, say Y to this option. If unsure, say N. 364 365config MSM_SERIAL 366 bool "Qualcomm on-chip UART" 367 depends on DM_SERIAL 368 help 369 Support Data Mover UART used on Qualcomm Snapdragon SoCs. 370 It should support all Qualcomm devices with UARTDM version 1.4, 371 for example APQ8016 and MSM8916. 372 Single baudrate is supported in current implementation (115200). 373endmenu 374