1 /* 2 * Copyright (C) 2005,2010-2011 Freescale Semiconductor, Inc. 3 * 4 * Author: Shlomi Gridish 5 * 6 * Description: UCC GETH Driver -- PHY handling 7 * Driver for UEC on QE 8 * Based on 8260_io/fcc_enet.c 9 * 10 * SPDX-License-Identifier: GPL-2.0+ 11 */ 12 13 #include "common.h" 14 #include "net.h" 15 #include "malloc.h" 16 #include "asm/errno.h" 17 #include "asm/immap_qe.h" 18 #include "asm/io.h" 19 #include "qe.h" 20 #include "uccf.h" 21 #include "uec.h" 22 #include "uec_phy.h" 23 #include "miiphy.h" 24 #include <phy.h> 25 26 #define ugphy_printk(format, arg...) \ 27 printf(format "\n", ## arg) 28 29 #define ugphy_dbg(format, arg...) \ 30 ugphy_printk(format , ## arg) 31 #define ugphy_err(format, arg...) \ 32 ugphy_printk(format , ## arg) 33 #define ugphy_info(format, arg...) \ 34 ugphy_printk(format , ## arg) 35 #define ugphy_warn(format, arg...) \ 36 ugphy_printk(format , ## arg) 37 38 #ifdef UEC_VERBOSE_DEBUG 39 #define ugphy_vdbg ugphy_dbg 40 #else 41 #define ugphy_vdbg(ugeth, fmt, args...) do { } while (0) 42 #endif /* UEC_VERBOSE_DEBUG */ 43 44 /*--------------------------------------------------------------------+ 45 * Fixed PHY (PHY-less) support for Ethernet Ports. 46 * 47 * Copied from arch/powerpc/cpu/ppc4xx/4xx_enet.c 48 *--------------------------------------------------------------------*/ 49 50 /* 51 * Some boards do not have a PHY for each ethernet port. These ports are known 52 * as Fixed PHY (or PHY-less) ports. For such ports, set the appropriate 53 * CONFIG_SYS_UECx_PHY_ADDR equal to CONFIG_FIXED_PHY_ADDR (an unused address) 54 * When the drver tries to identify the PHYs, CONFIG_FIXED_PHY will be returned 55 * and the driver will search CONFIG_SYS_FIXED_PHY_PORTS to find what network 56 * speed and duplex should be for the port. 57 * 58 * Example board header configuration file: 59 * #define CONFIG_FIXED_PHY 0xFFFFFFFF 60 * #define CONFIG_SYS_FIXED_PHY_ADDR 0x1E (pick an unused phy address) 61 * 62 * #define CONFIG_SYS_UEC1_PHY_ADDR CONFIG_SYS_FIXED_PHY_ADDR 63 * #define CONFIG_SYS_UEC2_PHY_ADDR 0x02 64 * #define CONFIG_SYS_UEC3_PHY_ADDR CONFIG_SYS_FIXED_PHY_ADDR 65 * #define CONFIG_SYS_UEC4_PHY_ADDR 0x04 66 * 67 * #define CONFIG_SYS_FIXED_PHY_PORT(name,speed,duplex) \ 68 * {name, speed, duplex}, 69 * 70 * #define CONFIG_SYS_FIXED_PHY_PORTS \ 71 * CONFIG_SYS_FIXED_PHY_PORT("UEC0",SPEED_100,DUPLEX_FULL) \ 72 * CONFIG_SYS_FIXED_PHY_PORT("UEC2",SPEED_100,DUPLEX_HALF) 73 */ 74 75 #ifndef CONFIG_FIXED_PHY 76 #define CONFIG_FIXED_PHY 0xFFFFFFFF /* Fixed PHY (PHY-less) */ 77 #endif 78 79 #ifndef CONFIG_SYS_FIXED_PHY_PORTS 80 #define CONFIG_SYS_FIXED_PHY_PORTS /* default is an empty array */ 81 #endif 82 83 struct fixed_phy_port { 84 char name[16]; /* ethernet port name */ 85 unsigned int speed; /* specified speed 10,100 or 1000 */ 86 unsigned int duplex; /* specified duplex FULL or HALF */ 87 }; 88 89 static const struct fixed_phy_port fixed_phy_port[] = { 90 CONFIG_SYS_FIXED_PHY_PORTS /* defined in board configuration file */ 91 }; 92 93 /*--------------------------------------------------------------------+ 94 * BitBang MII support for ethernet ports 95 * 96 * Based from MPC8560ADS implementation 97 *--------------------------------------------------------------------*/ 98 /* 99 * Example board header file to define bitbang ethernet ports: 100 * 101 * #define CONFIG_SYS_BITBANG_PHY_PORT(name) name, 102 * #define CONFIG_SYS_BITBANG_PHY_PORTS CONFIG_SYS_BITBANG_PHY_PORT("UEC0") 103 */ 104 #ifndef CONFIG_SYS_BITBANG_PHY_PORTS 105 #define CONFIG_SYS_BITBANG_PHY_PORTS /* default is an empty array */ 106 #endif 107 108 #if defined(CONFIG_BITBANGMII) 109 static const char *bitbang_phy_port[] = { 110 CONFIG_SYS_BITBANG_PHY_PORTS /* defined in board configuration file */ 111 }; 112 #endif /* CONFIG_BITBANGMII */ 113 114 static void config_genmii_advert (struct uec_mii_info *mii_info); 115 static void genmii_setup_forced (struct uec_mii_info *mii_info); 116 static void genmii_restart_aneg (struct uec_mii_info *mii_info); 117 static int gbit_config_aneg (struct uec_mii_info *mii_info); 118 static int genmii_config_aneg (struct uec_mii_info *mii_info); 119 static int genmii_update_link (struct uec_mii_info *mii_info); 120 static int genmii_read_status (struct uec_mii_info *mii_info); 121 u16 uec_phy_read(struct uec_mii_info *mii_info, u16 regnum); 122 void uec_phy_write(struct uec_mii_info *mii_info, u16 regnum, u16 val); 123 124 /* Write value to the PHY for this device to the register at regnum, */ 125 /* waiting until the write is done before it returns. All PHY */ 126 /* configuration has to be done through the TSEC1 MIIM regs */ 127 void uec_write_phy_reg (struct eth_device *dev, int mii_id, int regnum, int value) 128 { 129 uec_private_t *ugeth = (uec_private_t *) dev->priv; 130 uec_mii_t *ug_regs; 131 enet_tbi_mii_reg_e mii_reg = (enet_tbi_mii_reg_e) regnum; 132 u32 tmp_reg; 133 134 135 #if defined(CONFIG_BITBANGMII) 136 u32 i = 0; 137 138 for (i = 0; i < ARRAY_SIZE(bitbang_phy_port); i++) { 139 if (strncmp(dev->name, bitbang_phy_port[i], 140 sizeof(dev->name)) == 0) { 141 (void)bb_miiphy_write(NULL, mii_id, regnum, value); 142 return; 143 } 144 } 145 #endif /* CONFIG_BITBANGMII */ 146 147 ug_regs = ugeth->uec_mii_regs; 148 149 /* Stop the MII management read cycle */ 150 out_be32 (&ug_regs->miimcom, 0); 151 /* Setting up the MII Mangement Address Register */ 152 tmp_reg = ((u32) mii_id << MIIMADD_PHY_ADDRESS_SHIFT) | mii_reg; 153 out_be32 (&ug_regs->miimadd, tmp_reg); 154 155 /* Setting up the MII Mangement Control Register with the value */ 156 out_be32 (&ug_regs->miimcon, (u32) value); 157 sync(); 158 159 /* Wait till MII management write is complete */ 160 while ((in_be32 (&ug_regs->miimind)) & MIIMIND_BUSY); 161 } 162 163 /* Reads from register regnum in the PHY for device dev, */ 164 /* returning the value. Clears miimcom first. All PHY */ 165 /* configuration has to be done through the TSEC1 MIIM regs */ 166 int uec_read_phy_reg (struct eth_device *dev, int mii_id, int regnum) 167 { 168 uec_private_t *ugeth = (uec_private_t *) dev->priv; 169 uec_mii_t *ug_regs; 170 enet_tbi_mii_reg_e mii_reg = (enet_tbi_mii_reg_e) regnum; 171 u32 tmp_reg; 172 u16 value; 173 174 175 #if defined(CONFIG_BITBANGMII) 176 u32 i = 0; 177 178 for (i = 0; i < ARRAY_SIZE(bitbang_phy_port); i++) { 179 if (strncmp(dev->name, bitbang_phy_port[i], 180 sizeof(dev->name)) == 0) { 181 (void)bb_miiphy_read(NULL, mii_id, regnum, &value); 182 return (value); 183 } 184 } 185 #endif /* CONFIG_BITBANGMII */ 186 187 ug_regs = ugeth->uec_mii_regs; 188 189 /* Setting up the MII Mangement Address Register */ 190 tmp_reg = ((u32) mii_id << MIIMADD_PHY_ADDRESS_SHIFT) | mii_reg; 191 out_be32 (&ug_regs->miimadd, tmp_reg); 192 193 /* clear MII management command cycle */ 194 out_be32 (&ug_regs->miimcom, 0); 195 sync(); 196 197 /* Perform an MII management read cycle */ 198 out_be32 (&ug_regs->miimcom, MIIMCOM_READ_CYCLE); 199 200 /* Wait till MII management write is complete */ 201 while ((in_be32 (&ug_regs->miimind)) & 202 (MIIMIND_NOT_VALID | MIIMIND_BUSY)); 203 204 /* Read MII management status */ 205 value = (u16) in_be32 (&ug_regs->miimstat); 206 if (value == 0xffff) 207 ugphy_vdbg 208 ("read wrong value : mii_id %d,mii_reg %d, base %08x", 209 mii_id, mii_reg, (u32) & (ug_regs->miimcfg)); 210 211 return (value); 212 } 213 214 void mii_clear_phy_interrupt (struct uec_mii_info *mii_info) 215 { 216 if (mii_info->phyinfo->ack_interrupt) 217 mii_info->phyinfo->ack_interrupt (mii_info); 218 } 219 220 void mii_configure_phy_interrupt (struct uec_mii_info *mii_info, 221 u32 interrupts) 222 { 223 mii_info->interrupts = interrupts; 224 if (mii_info->phyinfo->config_intr) 225 mii_info->phyinfo->config_intr (mii_info); 226 } 227 228 /* Writes MII_ADVERTISE with the appropriate values, after 229 * sanitizing advertise to make sure only supported features 230 * are advertised 231 */ 232 static void config_genmii_advert (struct uec_mii_info *mii_info) 233 { 234 u32 advertise; 235 u16 adv; 236 237 /* Only allow advertising what this PHY supports */ 238 mii_info->advertising &= mii_info->phyinfo->features; 239 advertise = mii_info->advertising; 240 241 /* Setup standard advertisement */ 242 adv = uec_phy_read(mii_info, MII_ADVERTISE); 243 adv &= ~(ADVERTISE_ALL | ADVERTISE_100BASE4); 244 if (advertise & ADVERTISED_10baseT_Half) 245 adv |= ADVERTISE_10HALF; 246 if (advertise & ADVERTISED_10baseT_Full) 247 adv |= ADVERTISE_10FULL; 248 if (advertise & ADVERTISED_100baseT_Half) 249 adv |= ADVERTISE_100HALF; 250 if (advertise & ADVERTISED_100baseT_Full) 251 adv |= ADVERTISE_100FULL; 252 uec_phy_write(mii_info, MII_ADVERTISE, adv); 253 } 254 255 static void genmii_setup_forced (struct uec_mii_info *mii_info) 256 { 257 u16 ctrl; 258 u32 features = mii_info->phyinfo->features; 259 260 ctrl = uec_phy_read(mii_info, MII_BMCR); 261 262 ctrl &= ~(BMCR_FULLDPLX | BMCR_SPEED100 | 263 BMCR_SPEED1000 | BMCR_ANENABLE); 264 ctrl |= BMCR_RESET; 265 266 switch (mii_info->speed) { 267 case SPEED_1000: 268 if (features & (SUPPORTED_1000baseT_Half 269 | SUPPORTED_1000baseT_Full)) { 270 ctrl |= BMCR_SPEED1000; 271 break; 272 } 273 mii_info->speed = SPEED_100; 274 case SPEED_100: 275 if (features & (SUPPORTED_100baseT_Half 276 | SUPPORTED_100baseT_Full)) { 277 ctrl |= BMCR_SPEED100; 278 break; 279 } 280 mii_info->speed = SPEED_10; 281 case SPEED_10: 282 if (features & (SUPPORTED_10baseT_Half 283 | SUPPORTED_10baseT_Full)) 284 break; 285 default: /* Unsupported speed! */ 286 ugphy_err ("%s: Bad speed!", mii_info->dev->name); 287 break; 288 } 289 290 uec_phy_write(mii_info, MII_BMCR, ctrl); 291 } 292 293 /* Enable and Restart Autonegotiation */ 294 static void genmii_restart_aneg (struct uec_mii_info *mii_info) 295 { 296 u16 ctl; 297 298 ctl = uec_phy_read(mii_info, MII_BMCR); 299 ctl |= (BMCR_ANENABLE | BMCR_ANRESTART); 300 uec_phy_write(mii_info, MII_BMCR, ctl); 301 } 302 303 static int gbit_config_aneg (struct uec_mii_info *mii_info) 304 { 305 u16 adv; 306 u32 advertise; 307 308 if (mii_info->autoneg) { 309 /* Configure the ADVERTISE register */ 310 config_genmii_advert (mii_info); 311 advertise = mii_info->advertising; 312 313 adv = uec_phy_read(mii_info, MII_CTRL1000); 314 adv &= ~(ADVERTISE_1000FULL | 315 ADVERTISE_1000HALF); 316 if (advertise & SUPPORTED_1000baseT_Half) 317 adv |= ADVERTISE_1000HALF; 318 if (advertise & SUPPORTED_1000baseT_Full) 319 adv |= ADVERTISE_1000FULL; 320 uec_phy_write(mii_info, MII_CTRL1000, adv); 321 322 /* Start/Restart aneg */ 323 genmii_restart_aneg (mii_info); 324 } else 325 genmii_setup_forced (mii_info); 326 327 return 0; 328 } 329 330 static int marvell_config_aneg (struct uec_mii_info *mii_info) 331 { 332 /* The Marvell PHY has an errata which requires 333 * that certain registers get written in order 334 * to restart autonegotiation */ 335 uec_phy_write(mii_info, MII_BMCR, BMCR_RESET); 336 337 uec_phy_write(mii_info, 0x1d, 0x1f); 338 uec_phy_write(mii_info, 0x1e, 0x200c); 339 uec_phy_write(mii_info, 0x1d, 0x5); 340 uec_phy_write(mii_info, 0x1e, 0); 341 uec_phy_write(mii_info, 0x1e, 0x100); 342 343 gbit_config_aneg (mii_info); 344 345 return 0; 346 } 347 348 static int genmii_config_aneg (struct uec_mii_info *mii_info) 349 { 350 if (mii_info->autoneg) { 351 /* Speed up the common case, if link is already up, speed and 352 duplex match, skip auto neg as it already matches */ 353 if (!genmii_read_status(mii_info) && mii_info->link) 354 if (mii_info->duplex == DUPLEX_FULL && 355 mii_info->speed == SPEED_100) 356 if (mii_info->advertising & 357 ADVERTISED_100baseT_Full) 358 return 0; 359 360 config_genmii_advert (mii_info); 361 genmii_restart_aneg (mii_info); 362 } else 363 genmii_setup_forced (mii_info); 364 365 return 0; 366 } 367 368 static int genmii_update_link (struct uec_mii_info *mii_info) 369 { 370 u16 status; 371 372 /* Status is read once to clear old link state */ 373 uec_phy_read(mii_info, MII_BMSR); 374 375 /* 376 * Wait if the link is up, and autonegotiation is in progress 377 * (ie - we're capable and it's not done) 378 */ 379 status = uec_phy_read(mii_info, MII_BMSR); 380 if ((status & BMSR_LSTATUS) && (status & BMSR_ANEGCAPABLE) 381 && !(status & BMSR_ANEGCOMPLETE)) { 382 int i = 0; 383 384 while (!(status & BMSR_ANEGCOMPLETE)) { 385 /* 386 * Timeout reached ? 387 */ 388 if (i > UGETH_AN_TIMEOUT) { 389 mii_info->link = 0; 390 return 0; 391 } 392 393 i++; 394 udelay(1000); /* 1 ms */ 395 status = uec_phy_read(mii_info, MII_BMSR); 396 } 397 mii_info->link = 1; 398 } else { 399 if (status & BMSR_LSTATUS) 400 mii_info->link = 1; 401 else 402 mii_info->link = 0; 403 } 404 405 return 0; 406 } 407 408 static int genmii_read_status (struct uec_mii_info *mii_info) 409 { 410 u16 status; 411 int err; 412 413 /* Update the link, but return if there 414 * was an error */ 415 err = genmii_update_link (mii_info); 416 if (err) 417 return err; 418 419 if (mii_info->autoneg) { 420 status = uec_phy_read(mii_info, MII_STAT1000); 421 422 if (status & (LPA_1000FULL | LPA_1000HALF)) { 423 mii_info->speed = SPEED_1000; 424 if (status & LPA_1000FULL) 425 mii_info->duplex = DUPLEX_FULL; 426 else 427 mii_info->duplex = DUPLEX_HALF; 428 } else { 429 status = uec_phy_read(mii_info, MII_LPA); 430 431 if (status & (LPA_10FULL | LPA_100FULL)) 432 mii_info->duplex = DUPLEX_FULL; 433 else 434 mii_info->duplex = DUPLEX_HALF; 435 if (status & (LPA_100FULL | LPA_100HALF)) 436 mii_info->speed = SPEED_100; 437 else 438 mii_info->speed = SPEED_10; 439 } 440 mii_info->pause = 0; 441 } 442 /* On non-aneg, we assume what we put in BMCR is the speed, 443 * though magic-aneg shouldn't prevent this case from occurring 444 */ 445 446 return 0; 447 } 448 449 static int bcm_init(struct uec_mii_info *mii_info) 450 { 451 struct eth_device *edev = mii_info->dev; 452 uec_private_t *uec = edev->priv; 453 454 gbit_config_aneg(mii_info); 455 456 if ((uec->uec_info->enet_interface_type == 457 PHY_INTERFACE_MODE_RGMII_RXID) && 458 (uec->uec_info->speed == SPEED_1000)) { 459 u16 val; 460 int cnt = 50; 461 462 /* Wait for aneg to complete. */ 463 do 464 val = uec_phy_read(mii_info, MII_BMSR); 465 while (--cnt && !(val & BMSR_ANEGCOMPLETE)); 466 467 /* Set RDX clk delay. */ 468 uec_phy_write(mii_info, 0x18, 0x7 | (7 << 12)); 469 470 val = uec_phy_read(mii_info, 0x18); 471 /* Set RDX-RXC skew. */ 472 val |= (1 << 8); 473 val |= (7 | (7 << 12)); 474 /* Write bits 14:0. */ 475 val |= (1 << 15); 476 uec_phy_write(mii_info, 0x18, val); 477 } 478 479 return 0; 480 } 481 482 static int uec_marvell_init(struct uec_mii_info *mii_info) 483 { 484 struct eth_device *edev = mii_info->dev; 485 uec_private_t *uec = edev->priv; 486 phy_interface_t iface = uec->uec_info->enet_interface_type; 487 int speed = uec->uec_info->speed; 488 489 if ((speed == SPEED_1000) && 490 (iface == PHY_INTERFACE_MODE_RGMII_ID || 491 iface == PHY_INTERFACE_MODE_RGMII_RXID || 492 iface == PHY_INTERFACE_MODE_RGMII_TXID)) { 493 int temp; 494 495 temp = uec_phy_read(mii_info, MII_M1111_PHY_EXT_CR); 496 if (iface == PHY_INTERFACE_MODE_RGMII_ID) { 497 temp |= MII_M1111_RX_DELAY | MII_M1111_TX_DELAY; 498 } else if (iface == PHY_INTERFACE_MODE_RGMII_RXID) { 499 temp &= ~MII_M1111_TX_DELAY; 500 temp |= MII_M1111_RX_DELAY; 501 } else if (iface == PHY_INTERFACE_MODE_RGMII_TXID) { 502 temp &= ~MII_M1111_RX_DELAY; 503 temp |= MII_M1111_TX_DELAY; 504 } 505 uec_phy_write(mii_info, MII_M1111_PHY_EXT_CR, temp); 506 507 temp = uec_phy_read(mii_info, MII_M1111_PHY_EXT_SR); 508 temp &= ~MII_M1111_HWCFG_MODE_MASK; 509 temp |= MII_M1111_HWCFG_MODE_RGMII; 510 uec_phy_write(mii_info, MII_M1111_PHY_EXT_SR, temp); 511 512 uec_phy_write(mii_info, MII_BMCR, BMCR_RESET); 513 } 514 515 return 0; 516 } 517 518 static int marvell_read_status (struct uec_mii_info *mii_info) 519 { 520 u16 status; 521 int err; 522 523 /* Update the link, but return if there 524 * was an error */ 525 err = genmii_update_link (mii_info); 526 if (err) 527 return err; 528 529 /* If the link is up, read the speed and duplex */ 530 /* If we aren't autonegotiating, assume speeds 531 * are as set */ 532 if (mii_info->autoneg && mii_info->link) { 533 int speed; 534 535 status = uec_phy_read(mii_info, MII_M1011_PHY_SPEC_STATUS); 536 537 /* Get the duplexity */ 538 if (status & MII_M1011_PHY_SPEC_STATUS_FULLDUPLEX) 539 mii_info->duplex = DUPLEX_FULL; 540 else 541 mii_info->duplex = DUPLEX_HALF; 542 543 /* Get the speed */ 544 speed = status & MII_M1011_PHY_SPEC_STATUS_SPD_MASK; 545 switch (speed) { 546 case MII_M1011_PHY_SPEC_STATUS_1000: 547 mii_info->speed = SPEED_1000; 548 break; 549 case MII_M1011_PHY_SPEC_STATUS_100: 550 mii_info->speed = SPEED_100; 551 break; 552 default: 553 mii_info->speed = SPEED_10; 554 break; 555 } 556 mii_info->pause = 0; 557 } 558 559 return 0; 560 } 561 562 static int marvell_ack_interrupt (struct uec_mii_info *mii_info) 563 { 564 /* Clear the interrupts by reading the reg */ 565 uec_phy_read(mii_info, MII_M1011_IEVENT); 566 567 return 0; 568 } 569 570 static int marvell_config_intr (struct uec_mii_info *mii_info) 571 { 572 if (mii_info->interrupts == MII_INTERRUPT_ENABLED) 573 uec_phy_write(mii_info, MII_M1011_IMASK, MII_M1011_IMASK_INIT); 574 else 575 uec_phy_write(mii_info, MII_M1011_IMASK, 576 MII_M1011_IMASK_CLEAR); 577 578 return 0; 579 } 580 581 static int dm9161_init (struct uec_mii_info *mii_info) 582 { 583 /* Reset the PHY */ 584 uec_phy_write(mii_info, MII_BMCR, uec_phy_read(mii_info, MII_BMCR) | 585 BMCR_RESET); 586 /* PHY and MAC connect */ 587 uec_phy_write(mii_info, MII_BMCR, uec_phy_read(mii_info, MII_BMCR) & 588 ~BMCR_ISOLATE); 589 590 uec_phy_write(mii_info, MII_DM9161_SCR, MII_DM9161_SCR_INIT); 591 592 config_genmii_advert (mii_info); 593 /* Start/restart aneg */ 594 genmii_config_aneg (mii_info); 595 596 return 0; 597 } 598 599 static int dm9161_config_aneg (struct uec_mii_info *mii_info) 600 { 601 return 0; 602 } 603 604 static int dm9161_read_status (struct uec_mii_info *mii_info) 605 { 606 u16 status; 607 int err; 608 609 /* Update the link, but return if there was an error */ 610 err = genmii_update_link (mii_info); 611 if (err) 612 return err; 613 /* If the link is up, read the speed and duplex 614 If we aren't autonegotiating assume speeds are as set */ 615 if (mii_info->autoneg && mii_info->link) { 616 status = uec_phy_read(mii_info, MII_DM9161_SCSR); 617 if (status & (MII_DM9161_SCSR_100F | MII_DM9161_SCSR_100H)) 618 mii_info->speed = SPEED_100; 619 else 620 mii_info->speed = SPEED_10; 621 622 if (status & (MII_DM9161_SCSR_100F | MII_DM9161_SCSR_10F)) 623 mii_info->duplex = DUPLEX_FULL; 624 else 625 mii_info->duplex = DUPLEX_HALF; 626 } 627 628 return 0; 629 } 630 631 static int dm9161_ack_interrupt (struct uec_mii_info *mii_info) 632 { 633 /* Clear the interrupt by reading the reg */ 634 uec_phy_read(mii_info, MII_DM9161_INTR); 635 636 return 0; 637 } 638 639 static int dm9161_config_intr (struct uec_mii_info *mii_info) 640 { 641 if (mii_info->interrupts == MII_INTERRUPT_ENABLED) 642 uec_phy_write(mii_info, MII_DM9161_INTR, MII_DM9161_INTR_INIT); 643 else 644 uec_phy_write(mii_info, MII_DM9161_INTR, MII_DM9161_INTR_STOP); 645 646 return 0; 647 } 648 649 static void dm9161_close (struct uec_mii_info *mii_info) 650 { 651 } 652 653 static int fixed_phy_aneg (struct uec_mii_info *mii_info) 654 { 655 mii_info->autoneg = 0; /* Turn off auto negotiation for fixed phy */ 656 return 0; 657 } 658 659 static int fixed_phy_read_status (struct uec_mii_info *mii_info) 660 { 661 int i = 0; 662 663 for (i = 0; i < ARRAY_SIZE(fixed_phy_port); i++) { 664 if (strncmp(mii_info->dev->name, fixed_phy_port[i].name, 665 strlen(mii_info->dev->name)) == 0) { 666 mii_info->speed = fixed_phy_port[i].speed; 667 mii_info->duplex = fixed_phy_port[i].duplex; 668 mii_info->link = 1; /* Link is always UP */ 669 mii_info->pause = 0; 670 break; 671 } 672 } 673 return 0; 674 } 675 676 static int smsc_config_aneg (struct uec_mii_info *mii_info) 677 { 678 return 0; 679 } 680 681 static int smsc_read_status (struct uec_mii_info *mii_info) 682 { 683 u16 status; 684 int err; 685 686 /* Update the link, but return if there 687 * was an error */ 688 err = genmii_update_link (mii_info); 689 if (err) 690 return err; 691 692 /* If the link is up, read the speed and duplex */ 693 /* If we aren't autonegotiating, assume speeds 694 * are as set */ 695 if (mii_info->autoneg && mii_info->link) { 696 int val; 697 698 status = uec_phy_read(mii_info, 0x1f); 699 val = (status & 0x1c) >> 2; 700 701 switch (val) { 702 case 1: 703 mii_info->duplex = DUPLEX_HALF; 704 mii_info->speed = SPEED_10; 705 break; 706 case 5: 707 mii_info->duplex = DUPLEX_FULL; 708 mii_info->speed = SPEED_10; 709 break; 710 case 2: 711 mii_info->duplex = DUPLEX_HALF; 712 mii_info->speed = SPEED_100; 713 break; 714 case 6: 715 mii_info->duplex = DUPLEX_FULL; 716 mii_info->speed = SPEED_100; 717 break; 718 } 719 mii_info->pause = 0; 720 } 721 722 return 0; 723 } 724 725 static struct phy_info phy_info_dm9161 = { 726 .phy_id = 0x0181b880, 727 .phy_id_mask = 0x0ffffff0, 728 .name = "Davicom DM9161E", 729 .init = dm9161_init, 730 .config_aneg = dm9161_config_aneg, 731 .read_status = dm9161_read_status, 732 .close = dm9161_close, 733 }; 734 735 static struct phy_info phy_info_dm9161a = { 736 .phy_id = 0x0181b8a0, 737 .phy_id_mask = 0x0ffffff0, 738 .name = "Davicom DM9161A", 739 .features = MII_BASIC_FEATURES, 740 .init = dm9161_init, 741 .config_aneg = dm9161_config_aneg, 742 .read_status = dm9161_read_status, 743 .ack_interrupt = dm9161_ack_interrupt, 744 .config_intr = dm9161_config_intr, 745 .close = dm9161_close, 746 }; 747 748 static struct phy_info phy_info_marvell = { 749 .phy_id = 0x01410c00, 750 .phy_id_mask = 0xffffff00, 751 .name = "Marvell 88E11x1", 752 .features = MII_GBIT_FEATURES, 753 .init = &uec_marvell_init, 754 .config_aneg = &marvell_config_aneg, 755 .read_status = &marvell_read_status, 756 .ack_interrupt = &marvell_ack_interrupt, 757 .config_intr = &marvell_config_intr, 758 }; 759 760 static struct phy_info phy_info_bcm5481 = { 761 .phy_id = 0x0143bca0, 762 .phy_id_mask = 0xffffff0, 763 .name = "Broadcom 5481", 764 .features = MII_GBIT_FEATURES, 765 .read_status = genmii_read_status, 766 .init = bcm_init, 767 }; 768 769 static struct phy_info phy_info_fixedphy = { 770 .phy_id = CONFIG_FIXED_PHY, 771 .phy_id_mask = CONFIG_FIXED_PHY, 772 .name = "Fixed PHY", 773 .config_aneg = fixed_phy_aneg, 774 .read_status = fixed_phy_read_status, 775 }; 776 777 static struct phy_info phy_info_smsclan8700 = { 778 .phy_id = 0x0007c0c0, 779 .phy_id_mask = 0xfffffff0, 780 .name = "SMSC LAN8700", 781 .features = MII_BASIC_FEATURES, 782 .config_aneg = smsc_config_aneg, 783 .read_status = smsc_read_status, 784 }; 785 786 static struct phy_info phy_info_genmii = { 787 .phy_id = 0x00000000, 788 .phy_id_mask = 0x00000000, 789 .name = "Generic MII", 790 .features = MII_BASIC_FEATURES, 791 .config_aneg = genmii_config_aneg, 792 .read_status = genmii_read_status, 793 }; 794 795 static struct phy_info *phy_info[] = { 796 &phy_info_dm9161, 797 &phy_info_dm9161a, 798 &phy_info_marvell, 799 &phy_info_bcm5481, 800 &phy_info_smsclan8700, 801 &phy_info_fixedphy, 802 &phy_info_genmii, 803 NULL 804 }; 805 806 u16 uec_phy_read(struct uec_mii_info *mii_info, u16 regnum) 807 { 808 return mii_info->mdio_read (mii_info->dev, mii_info->mii_id, regnum); 809 } 810 811 void uec_phy_write(struct uec_mii_info *mii_info, u16 regnum, u16 val) 812 { 813 mii_info->mdio_write (mii_info->dev, mii_info->mii_id, regnum, val); 814 } 815 816 /* Use the PHY ID registers to determine what type of PHY is attached 817 * to device dev. return a struct phy_info structure describing that PHY 818 */ 819 struct phy_info *uec_get_phy_info (struct uec_mii_info *mii_info) 820 { 821 u16 phy_reg; 822 u32 phy_ID; 823 int i; 824 struct phy_info *theInfo = NULL; 825 826 /* Grab the bits from PHYIR1, and put them in the upper half */ 827 phy_reg = uec_phy_read(mii_info, MII_PHYSID1); 828 phy_ID = (phy_reg & 0xffff) << 16; 829 830 /* Grab the bits from PHYIR2, and put them in the lower half */ 831 phy_reg = uec_phy_read(mii_info, MII_PHYSID2); 832 phy_ID |= (phy_reg & 0xffff); 833 834 /* loop through all the known PHY types, and find one that */ 835 /* matches the ID we read from the PHY. */ 836 for (i = 0; phy_info[i]; i++) 837 if (phy_info[i]->phy_id == 838 (phy_ID & phy_info[i]->phy_id_mask)) { 839 theInfo = phy_info[i]; 840 break; 841 } 842 843 /* This shouldn't happen, as we have generic PHY support */ 844 if (theInfo == NULL) { 845 ugphy_info ("UEC: PHY id %x is not supported!", phy_ID); 846 return NULL; 847 } else { 848 ugphy_info ("UEC: PHY is %s (%x)", theInfo->name, phy_ID); 849 } 850 851 return theInfo; 852 } 853 854 void marvell_phy_interface_mode(struct eth_device *dev, phy_interface_t type, 855 int speed) 856 { 857 uec_private_t *uec = (uec_private_t *) dev->priv; 858 struct uec_mii_info *mii_info; 859 u16 status; 860 861 if (!uec->mii_info) { 862 printf ("%s: the PHY not initialized\n", __FUNCTION__); 863 return; 864 } 865 mii_info = uec->mii_info; 866 867 if (type == PHY_INTERFACE_MODE_RGMII) { 868 if (speed == SPEED_100) { 869 uec_phy_write(mii_info, 0x00, 0x9140); 870 uec_phy_write(mii_info, 0x1d, 0x001f); 871 uec_phy_write(mii_info, 0x1e, 0x200c); 872 uec_phy_write(mii_info, 0x1d, 0x0005); 873 uec_phy_write(mii_info, 0x1e, 0x0000); 874 uec_phy_write(mii_info, 0x1e, 0x0100); 875 uec_phy_write(mii_info, 0x09, 0x0e00); 876 uec_phy_write(mii_info, 0x04, 0x01e1); 877 uec_phy_write(mii_info, 0x00, 0x9140); 878 uec_phy_write(mii_info, 0x00, 0x1000); 879 udelay (100000); 880 uec_phy_write(mii_info, 0x00, 0x2900); 881 uec_phy_write(mii_info, 0x14, 0x0cd2); 882 uec_phy_write(mii_info, 0x00, 0xa100); 883 uec_phy_write(mii_info, 0x09, 0x0000); 884 uec_phy_write(mii_info, 0x1b, 0x800b); 885 uec_phy_write(mii_info, 0x04, 0x05e1); 886 uec_phy_write(mii_info, 0x00, 0xa100); 887 uec_phy_write(mii_info, 0x00, 0x2100); 888 udelay (1000000); 889 } else if (speed == SPEED_10) { 890 uec_phy_write(mii_info, 0x14, 0x8e40); 891 uec_phy_write(mii_info, 0x1b, 0x800b); 892 uec_phy_write(mii_info, 0x14, 0x0c82); 893 uec_phy_write(mii_info, 0x00, 0x8100); 894 udelay (1000000); 895 } 896 } 897 898 /* handle 88e1111 rev.B2 erratum 5.6 */ 899 if (mii_info->autoneg) { 900 status = uec_phy_read(mii_info, MII_BMCR); 901 uec_phy_write(mii_info, MII_BMCR, status | BMCR_ANENABLE); 902 } 903 /* now the B2 will correctly report autoneg completion status */ 904 } 905 906 void change_phy_interface_mode (struct eth_device *dev, 907 phy_interface_t type, int speed) 908 { 909 #ifdef CONFIG_PHY_MODE_NEED_CHANGE 910 marvell_phy_interface_mode (dev, type, speed); 911 #endif 912 } 913